Bitcoin Forum>Bitcoin>Mining>Mining support
Author

Topic: S17 Pro Help, Miners Keep Restarting (Read 193 times)

mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
S17 Pro Help, Miners Keep Restarting
February 02, 2021, 06:57:58 PM
#10
Quote from: NotFuzzyWarm on February 02, 2021, 03:48:20 PM
Query: Are the miners and laptop using DHCP or static IP addresses? If they are static addresses perhaps the laptop is using the same address as your router or a miner and causing a conflict somewhere.

This is a good point but based on this theory and regardless of his set-up the worst result that would come out of an IP conflict would be 1 miner going offline, also if the laptop was using the gateway address as its own IP it can't possibly affect the router the way OP describes.

It's most likely this

Quote from: favebook on January 29, 2021, 03:43:07 PM
Were you using too much bandwidth on your laptop so some machines were dropping hash on dev fee and then they would restart? Or did your laptop just idle?

Quote from: BigStarMine on February 02, 2021, 03:22:00 PM
Just the laptop getting on the network would cause the problems. it wasn't using any bandwidth, it just logged on.

If it's logged in then it's connected to the network, and thus is using bandwidth, I would refrain from using the word bandwidth to clear a lot of confusion, and let's call it "traffic", there is an on-going connection between the laptop and the router as long as they are connected, even if it was sitting there doing nothing, also, it could be doing something in the background such as windows/antivirus update, unless you closely monitor the router's inbound and outbound traffic you can't tell.

With that being said, if your laptop caused that then it's very likely that either your router or internet speed is pretty must at a critical level, so the slightest extra traffic will again cause the same issue, you might want to get a proper router and perbaps a better internet connection, you can't tell where the problem actualy is unless you troubelshoot it.
NotFuzzyWarm
legendary
Activity: 3822
Merit: 2703
Evil beware: We have waffles!
Re: S17 Pro Help, Miners Keep Restarting
February 02, 2021, 03:48:20 PM
#9
Query: Are the miners and laptop using DHCP or static IP addresses? If they are static addresses perhaps the laptop is using the same address as your router or a miner and causing a conflict somewhere.
BigStarMine
newbie
Activity: 6
Merit: 1
Re: S17 Pro Help, Miners Keep Restarting
February 02, 2021, 03:22:00 PM
#8
Quote from: favebook on January 29, 2021, 03:43:07 PM
I am not sure how could that be a problem. Were you using too much bandwidth on your laptop so some machines were dropping hash on dev fee and then they would restart? Or did your laptop just idle?

Just the laptop getting on the network would cause the problems. it wasn't using any bandwidth, it just logged on. It is the craziest thing and haven't had a problem since.

Quote from: wndsnb on January 29, 2021, 05:59:13 PM
Yeah, also can't think of any way for a device on the network would do that, especially only to some of the miners. Do the miners go down when you turn the laptop back on?

yes they do. Also no problems when the lap[top is off the network. It has been running smooth ever since 5-6 days now.
wndsnb
hero member
Activity: 544
Merit: 589
Re: S17 Pro Help, Miners Keep Restarting
January 29, 2021, 05:59:13 PM
#7
Yeah, also can't think of any way for a device on the network would do that, especially only to some of the miners. Do the miners go down when you turn the laptop back on?
favebook
sr. member
Activity: 604
Merit: 416
Re: S17 Pro Help, Miners Keep Restarting
January 29, 2021, 03:43:07 PM
#6
Quote from: BigStarMine on January 29, 2021, 10:34:24 AM
Just to keep things updated, the problem seems to be a laptop that was causing a conflict with these 6 miners. Took the laptop offline and it has been perfect for 48 hours. What was causing the conflict I am not sure yet! I changed IP addresses and moved their locations in the mine. By chance this laptop came on at the right time and it started happening. It was luck to catch it like that, now to find out why.

I am not sure how could that be a problem. Were you using too much bandwidth on your laptop so some machines were dropping hash on dev fee and then they would restart? Or did your laptop just idle?
BigStarMine
newbie
Activity: 6
Merit: 1
Re: S17 Pro Help, Miners Keep Restarting
January 29, 2021, 10:34:24 AM
#5
Just to keep things updated, the problem seems to be a laptop that was causing a conflict with these 6 miners. Took the laptop offline and it has been perfect for 48 hours. What was causing the conflict I am not sure yet! I changed IP addresses and moved their locations in the mine. By chance this laptop came on at the right time and it started happening. It was luck to catch it like that, now to find out why.
favebook
sr. member
Activity: 604
Merit: 416
Re: S17 Pro Help, Miners Keep Restarting
January 26, 2021, 07:47:38 PM
#4
I'd firstly try unplugging them and letting them "rest" for a few minutes and the turning them on again.

If I see right, you are using Vnish (Asic.to) firmware, which should by default restart it whenever it fails to boot or encounters a problem during mining, you can disable some of those "features" in options if you want to mine without interrupts with few of those hashboards that work fine.

Although, I would check the PSUs. They are "easy" to replace especially if you have that many units, you can take one from 100% working one and try it on problematic ones.
But do keep in mind that transferring PSU from one unit to another takes 15-20min.
BigStarMine
newbie
Activity: 6
Merit: 1
Re: S17 Pro Help, Miners Keep Restarting
January 26, 2021, 01:18:29 PM
#3
I will get on that now, and keep you updated.
wndsnb
hero member
Activity: 544
Merit: 589
Re: S17 Pro Help, Miners Keep Restarting
January 26, 2021, 01:16:30 PM
#2
So now I'm more confident that your issue is the control board. I had this exact problem on a S17 a few months ago, the same one that gave me the "Malformed power response" error. I eventually had to replace the control board to get it to work reliably.

My suggestion is to try doing a factory reset and reflashing the firmware, then try a known good control board, and if that doesn't work try a known good PSU.
BigStarMine
newbie
Activity: 6
Merit: 1
Re: S17 Pro Help, Miners Keep Restarting
January 26, 2021, 01:04:46 PM
#1
Hello,

I am new here and am lost so hopefully someone can help or point me in the right direction.

i have 192 s17 pro's running in total immersion, with awesome miner firmware. All of a sudden 3 days ago 6 of them all came down with the exact same problem. They will start up running 144/144 chips hash perfectly for 3-5 minutes, then hashing power goes down for a minute then restarts. it will do it indefinitely if i allow it. currently i have them shut off to protect the miners. I am posting the kernel log and the miner log as well and well answer any questions you may have I am stumped.

Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203020K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 26356K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 13316K (ccdff000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 76/49, WL threshold: 4096, image sequence number: 306349061
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 038216C1-D266-46DA-A76E-C04B142933A3, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 415/151, WL threshold: 4096, image sequence number: 1751317449
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 51C7124B-A562-4AA0-948B-184BE8DB9030, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
random: nonblocking pool is initialized

Code:
[2021/01/25 12:51:05] INFO: Start mining!
[2021/01/25 12:52:05] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 12:52:29] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 12:52:53] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 12:53:17] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:10:39] INFO: Detected 256 Mb of RAM
[2021/01/25 13:10:39] INFO: Switching to immersion fan control
[2021/01/25 13:10:45] INFO: Power ON
[2021/01/25 13:10:47] ERROR: src/power.c:161 Malformed power response
[2021/01/25 13:10:49] INFO: Starting FPGA queue
[2021/01/25 13:10:49] INFO: Initializing hash boards
[2021/01/25 13:10:49] INFO: chain[0] - Initializing
[2021/01/25 13:10:49] INFO: chain[1] - Initializing
[2021/01/25 13:10:49] INFO: chain[2] - Initializing
[2021/01/25 13:11:05] INFO: chain[0] - 48 chips detected
[2021/01/25 13:11:07] INFO: chain[1] - 48 chips detected
[2021/01/25 13:11:08] INFO: chain[2] - 48 chips detected
[2021/01/25 13:11:15] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:11:15] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:11:15] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:11:47] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:12:03] INFO: Switching to immersion fan control
[2021/01/25 13:12:03] INFO: Start mining!
[2021/01/25 13:13:03] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:13:26] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:13:51] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:14:15] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:15:17] INFO: Detected 256 Mb of RAM
[2021/01/25 13:15:17] INFO: Switching to immersion fan control
[2021/01/25 13:15:23] INFO: Power ON
[2021/01/25 13:15:25] INFO: Starting FPGA queue
[2021/01/25 13:15:25] INFO: Initializing hash boards
[2021/01/25 13:15:25] INFO: chain[0] - Initializing
[2021/01/25 13:15:25] INFO: chain[1] - Initializing
[2021/01/25 13:15:25] INFO: chain[2] - Initializing
[2021/01/25 13:15:41] INFO: chain[0] - 48 chips detected
[2021/01/25 13:15:43] INFO: chain[1] - 48 chips detected
[2021/01/25 13:15:44] INFO: chain[2] - 48 chips detected
[2021/01/25 13:15:51] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:15:51] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:15:51] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:16:23] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:16:39] INFO: Switching to immersion fan control
[2021/01/25 13:16:39] INFO: Start mining!
[2021/01/25 13:17:39] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:18:02] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:18:27] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:18:51] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:27:03] INFO: Detected 256 Mb of RAM
[2021/01/25 13:27:03] INFO: Switching to immersion fan control
[2021/01/25 13:27:09] INFO: Power ON
[2021/01/25 13:27:11] INFO: Starting FPGA queue
[2021/01/25 13:27:11] INFO: Initializing hash boards
[2021/01/25 13:27:11] INFO: chain[0] - Initializing
[2021/01/25 13:27:11] INFO: chain[1] - Initializing
[2021/01/25 13:27:11] INFO: chain[2] - Initializing
[2021/01/25 13:27:27] INFO: chain[0] - 48 chips detected
[2021/01/25 13:27:29] INFO: chain[1] - 48 chips detected
[2021/01/25 13:27:31] INFO: chain[2] - 48 chips detected
[2021/01/25 13:27:38] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:27:38] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:27:38] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:28:10] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:28:26] INFO: Switching to immersion fan control
[2021/01/25 13:28:26] INFO: Start mining!
[2021/01/25 13:29:26] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:29:50] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:30:14] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:30:38] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:31:21] INFO: Detected 256 Mb of RAM
[2021/01/25 13:31:21] INFO: Switching to immersion fan control
[2021/01/25 13:31:27] INFO: Power ON
[2021/01/25 13:31:29] INFO: Starting FPGA queue
[2021/01/25 13:31:29] INFO: Initializing hash boards
[2021/01/25 13:31:29] INFO: chain[0] - Initializing
[2021/01/25 13:31:29] INFO: chain[1] - Initializing
[2021/01/25 13:31:29] INFO: chain[2] - Initializing
[2021/01/25 13:31:45] INFO: chain[0] - 48 chips detected
[2021/01/25 13:31:47] INFO: chain[1] - 48 chips detected
[2021/01/25 13:31:49] INFO: chain[2] - 48 chips detected
[2021/01/25 13:31:56] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:31:56] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:31:56] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:32:27] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:32:44] INFO: Switching to immersion fan control
[2021/01/25 13:32:44] INFO: Start mining!
[2021/01/25 13:33:44] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:34:07] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:34:32] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:34:55] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:37:00] INFO: Detected 256 Mb of RAM
[2021/01/25 13:37:00] INFO: Switching to immersion fan control
[2021/01/25 13:37:06] INFO: Power ON
[2021/01/25 13:37:08] INFO: Starting FPGA queue
[2021/01/25 13:37:08] INFO: Initializing hash boards
[2021/01/25 13:37:08] INFO: chain[0] - Initializing
[2021/01/25 13:37:08] INFO: chain[1] - Initializing
[2021/01/25 13:37:08] INFO: chain[2] - Initializing
[2021/01/25 13:37:24] INFO: chain[0] - 48 chips detected
[2021/01/25 13:37:26] INFO: chain[1] - 48 chips detected
[2021/01/25 13:37:28] INFO: chain[2] - 48 chips detected
[2021/01/25 13:37:35] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:37:35] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:37:35] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:38:07] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:38:23] INFO: Switching to immersion fan control
[2021/01/25 13:38:23] INFO: Start mining!
[2021/01/25 13:39:23] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:39:46] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:40:11] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:40:35] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:40:59] INFO: Detected 256 Mb of RAM
[2021/01/25 13:40:59] INFO: Switching to immersion fan control
[2021/01/25 13:41:05] INFO: Power ON
[2021/01/25 13:41:07] INFO: Starting FPGA queue
[2021/01/25 13:41:07] INFO: Initializing hash boards
[2021/01/25 13:41:07] INFO: chain[1] - Initializing
[2021/01/25 13:41:07] INFO: chain[0] - Initializing
[2021/01/25 13:41:07] INFO: chain[2] - Initializing
[2021/01/25 13:41:23] INFO: chain[1] - 48 chips detected
[2021/01/25 13:41:25] INFO: chain[0] - 48 chips detected
[2021/01/25 13:41:27] INFO: chain[2] - 48 chips detected
[2021/01/25 13:41:34] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:41:34] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:41:34] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:42:06] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:42:22] INFO: Switching to immersion fan control
[2021/01/25 13:42:22] INFO: Start mining!
[2021/01/25 13:43:22] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:43:45] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:44:10] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:44:34] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:44:56] INFO: Detected 256 Mb of RAM
[2021/01/25 13:44:56] INFO: Switching to immersion fan control
[2021/01/25 13:45:02] INFO: Power ON
[2021/01/25 13:45:04] INFO: Starting FPGA queue
[2021/01/25 13:45:04] INFO: Initializing hash boards
[2021/01/25 13:45:04] INFO: chain[0] - Initializing
[2021/01/25 13:45:04] INFO: chain[2] - Initializing
[2021/01/25 13:45:04] INFO: chain[1] - Initializing
[2021/01/25 13:45:21] INFO: chain[0] - 48 chips detected
[2021/01/25 13:45:23] INFO: chain[2] - 48 chips detected
[2021/01/25 13:45:25] INFO: chain[1] - 48 chips detected
[2021/01/25 13:45:32] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:45:32] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:45:32] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:46:03] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:46:19] INFO: Switching to immersion fan control
[2021/01/25 13:46:19] INFO: Start mining!
[2021/01/25 13:47:19] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:47:43] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:48:07] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:48:31] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:48:55] INFO: Detected 256 Mb of RAM
[2021/01/25 13:48:55] INFO: Switching to immersion fan control
[2021/01/25 13:49:01] INFO: Power ON
[2021/01/25 13:49:03] INFO: Starting FPGA queue
[2021/01/25 13:49:03] INFO: Initializing hash boards
[2021/01/25 13:49:03] INFO: chain[0] - Initializing
[2021/01/25 13:49:03] INFO: chain[2] - Initializing
[2021/01/25 13:49:03] INFO: chain[1] - Initializing
[2021/01/25 13:49:19] INFO: chain[0] - 48 chips detected
[2021/01/25 13:49:21] INFO: chain[2] - 48 chips detected
[2021/01/25 13:49:23] INFO: chain[1] - 48 chips detected
[2021/01/25 13:49:30] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:49:30] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:49:30] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:50:02] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:50:18] INFO: Switching to immersion fan control
[2021/01/25 13:50:18] INFO: Start mining!
[2021/01/25 13:51:18] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:51:41] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:52:06] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:52:29] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 13:53:52] INFO: Detected 256 Mb of RAM
[2021/01/25 13:53:52] INFO: Switching to immersion fan control
[2021/01/25 13:53:58] INFO: Power ON
[2021/01/25 13:54:00] INFO: Starting FPGA queue
[2021/01/25 13:54:00] INFO: Initializing hash boards
[2021/01/25 13:54:00] INFO: chain[0] - Initializing
[2021/01/25 13:54:00] INFO: chain[1] - Initializing
[2021/01/25 13:54:00] INFO: chain[2] - Initializing
[2021/01/25 13:54:16] INFO: chain[0] - 48 chips detected
[2021/01/25 13:54:18] INFO: chain[1] - 48 chips detected
[2021/01/25 13:54:20] INFO: chain[2] - 48 chips detected
[2021/01/25 13:54:28] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 13:54:28] INFO: Switching to manual fan control (100 %)
[2021/01/25 13:54:28] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 13:54:59] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 13:55:15] INFO: Switching to immersion fan control
[2021/01/25 13:55:15] INFO: Start mining!
[2021/01/25 13:56:15] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 13:56:39] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 13:57:03] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 13:57:27] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 14:10:23] INFO: Detected 256 Mb of RAM
[2021/01/25 14:10:23] INFO: Switching to immersion fan control
[2021/01/25 14:10:29] INFO: Power ON
[2021/01/25 14:10:31] INFO: Starting FPGA queue
[2021/01/25 14:10:31] INFO: Initializing hash boards
[2021/01/25 14:10:31] INFO: chain[1] - Initializing
[2021/01/25 14:10:31] INFO: chain[0] - Initializing
[2021/01/25 14:10:31] INFO: chain[2] - Initializing
[2021/01/25 14:10:47] INFO: chain[1] - 48 chips detected
[2021/01/25 14:10:49] INFO: chain[0] - 48 chips detected
[2021/01/25 14:10:51] INFO: chain[2] - 48 chips detected
[2021/01/25 14:10:59] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 14:10:59] INFO: Switching to manual fan control (100 %)
[2021/01/25 14:10:59] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 14:11:30] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 14:11:46] INFO: Switching to immersion fan control
[2021/01/25 14:11:46] INFO: Start mining!
[2021/01/25 14:12:46] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 14:13:08] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 14:13:31] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 14:13:55] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 14:14:21] INFO: Detected 256 Mb of RAM
[2021/01/25 14:14:21] INFO: Switching to immersion fan control
[2021/01/25 14:14:27] INFO: Power ON
[2021/01/25 14:14:29] INFO: Starting FPGA queue
[2021/01/25 14:14:29] INFO: Initializing hash boards
[2021/01/25 14:14:29] INFO: chain[0] - Initializing
[2021/01/25 14:14:29] INFO: chain[1] - Initializing
[2021/01/25 14:14:29] INFO: chain[2] - Initializing
[2021/01/25 14:14:45] INFO: chain[0] - 48 chips detected
[2021/01/25 14:14:47] INFO: chain[1] - 48 chips detected
[2021/01/25 14:14:48] INFO: chain[2] - 48 chips detected
[2021/01/25 14:14:56] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 14:14:56] INFO: Switching to manual fan control (100 %)
[2021/01/25 14:14:56] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 14:15:27] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 14:15:43] INFO: Switching to immersion fan control
[2021/01/25 14:15:43] INFO: Start mining!
[2021/01/25 14:16:43] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 14:17:07] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 14:17:31] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 14:18:18] INFO: Detected 256 Mb of RAM
[2021/01/25 14:18:18] INFO: Switching to immersion fan control
[2021/01/25 14:18:24] INFO: Power ON
[2021/01/25 14:18:26] INFO: Starting FPGA queue
[2021/01/25 14:18:26] INFO: Initializing hash boards
[2021/01/25 14:18:26] INFO: chain[2] - Initializing
[2021/01/25 14:18:26] INFO: chain[0] - Initializing
[2021/01/25 14:18:26] INFO: chain[1] - Initializing
[2021/01/25 14:18:41] INFO: chain[2] - 48 chips detected
[2021/01/25 14:18:43] INFO: chain[0] - 48 chips detected
[2021/01/25 14:18:45] INFO: chain[1] - 48 chips detected
[2021/01/25 14:18:52] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 14:18:52] INFO: Switching to manual fan control (100 %)
[2021/01/25 14:18:52] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 14:19:24] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 14:19:40] INFO: Switching to immersion fan control
[2021/01/25 14:19:40] INFO: Start mining!
[2021/01/25 14:20:40] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 14:21:03] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 14:21:28] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 14:21:51] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 14:31:24] INFO: Detected 256 Mb of RAM
[2021/01/25 14:31:24] INFO: Switching to immersion fan control
[2021/01/25 14:31:31] INFO: Power ON
[2021/01/25 14:31:33] INFO: Starting FPGA queue
[2021/01/25 14:31:33] INFO: Initializing hash boards
[2021/01/25 14:31:33] INFO: chain[1] - Initializing
[2021/01/25 14:31:33] INFO: chain[2] - Initializing
[2021/01/25 14:31:33] INFO: chain[0] - Initializing
[2021/01/25 14:31:49] INFO: chain[1] - 48 chips detected
[2021/01/25 14:31:51] INFO: chain[2] - 48 chips detected
[2021/01/25 14:31:53] INFO: chain[0] - 48 chips detected
[2021/01/25 14:32:00] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 14:32:00] INFO: Switching to manual fan control (100 %)
[2021/01/25 14:32:00] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 14:32:31] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 14:32:47] INFO: Switching to immersion fan control
[2021/01/25 14:32:47] INFO: Start mining!
[2021/01/25 14:33:47] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 14:34:11] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 14:34:36] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 14:34:59] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 14:40:06] INFO: Detected 256 Mb of RAM
[2021/01/25 14:40:06] INFO: Switching to immersion fan control
[2021/01/25 14:40:12] INFO: Power ON
[2021/01/25 14:40:14] INFO: Starting FPGA queue
[2021/01/25 14:40:14] INFO: Initializing hash boards
[2021/01/25 14:40:14] INFO: chain[0] - Initializing
[2021/01/25 14:40:14] INFO: chain[1] - Initializing
[2021/01/25 14:40:14] INFO: chain[2] - Initializing
[2021/01/25 14:40:30] INFO: chain[0] - 48 chips detected
[2021/01/25 14:40:32] INFO: chain[1] - 48 chips detected
[2021/01/25 14:40:34] INFO: chain[2] - 48 chips detected
[2021/01/25 14:40:42] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 14:40:42] INFO: Switching to manual fan control (100 %)
[2021/01/25 14:40:42] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 14:41:13] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 14:41:29] INFO: Switching to immersion fan control
[2021/01/25 14:41:29] INFO: Start mining!
[2021/01/25 14:42:29] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 14:42:53] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 14:43:17] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 14:43:41] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:08:13] INFO: Detected 256 Mb of RAM
[2021/01/25 15:08:13] INFO: Switching to immersion fan control
[2021/01/25 15:08:20] INFO: Power ON
[2021/01/25 15:08:22] INFO: Starting FPGA queue
[2021/01/25 15:08:22] INFO: Initializing hash boards
[2021/01/25 15:08:22] INFO: chain[0] - Initializing
[2021/01/25 15:08:22] INFO: chain[2] - Initializing
[2021/01/25 15:08:22] INFO: chain[1] - Initializing
[2021/01/25 15:08:38] INFO: chain[0] - 48 chips detected
[2021/01/25 15:08:40] INFO: chain[2] - 48 chips detected
[2021/01/25 15:08:42] INFO: chain[1] - 48 chips detected
[2021/01/25 15:08:49] INFO: Start-up temperature is 40 C (min -15 C)
[2021/01/25 15:08:49] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:08:49] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:09:20] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:09:36] INFO: Switching to immersion fan control
[2021/01/25 15:09:36] INFO: Start mining!
[2021/01/25 15:10:36] INFO: Detected 256 Mb of RAM
[2021/01/25 15:10:36] INFO: Switching to immersion fan control
[2021/01/25 15:10:42] INFO: Power ON
[2021/01/25 15:10:44] INFO: Starting FPGA queue
[2021/01/25 15:10:44] INFO: Initializing hash boards
[2021/01/25 15:10:44] INFO: chain[2] - Initializing
[2021/01/25 15:10:44] INFO: chain[1] - Initializing
[2021/01/25 15:10:44] INFO: chain[0] - Initializing
[2021/01/25 15:11:00] INFO: chain[2] - 48 chips detected
[2021/01/25 15:11:01] INFO: chain[1] - 48 chips detected
[2021/01/25 15:11:03] INFO: chain[0] - 48 chips detected
[2021/01/25 15:11:10] INFO: Start-up temperature is 40 C (min -15 C)
[2021/01/25 15:11:10] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:11:10] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:11:42] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:11:58] INFO: Switching to immersion fan control
[2021/01/25 15:11:58] INFO: Start mining!
[2021/01/25 15:12:58] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:13:21] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:13:46] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:14:10] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:15:45] INFO: Detected 256 Mb of RAM
[2021/01/25 15:15:45] INFO: Switching to immersion fan control
[2021/01/25 15:15:51] INFO: Power ON
[2021/01/25 15:15:53] INFO: Starting FPGA queue
[2021/01/25 15:15:53] INFO: Initializing hash boards
[2021/01/25 15:15:53] INFO: chain[2] - Initializing
[2021/01/25 15:15:53] INFO: chain[1] - Initializing
[2021/01/25 15:15:53] INFO: chain[0] - Initializing
[2021/01/25 15:16:09] INFO: chain[2] - 48 chips detected
[2021/01/25 15:16:11] INFO: chain[1] - 48 chips detected
[2021/01/25 15:16:13] INFO: chain[0] - 48 chips detected
[2021/01/25 15:16:20] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 15:16:20] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:16:20] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:16:52] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:17:08] INFO: Switching to immersion fan control
[2021/01/25 15:17:08] INFO: Start mining!
[2021/01/25 15:18:08] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:18:31] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:18:56] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:19:20] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:21:25] INFO: Detected 256 Mb of RAM
[2021/01/25 15:21:25] INFO: Switching to immersion fan control
[2021/01/25 15:21:31] INFO: Power ON
[2021/01/25 15:21:33] INFO: Starting FPGA queue
[2021/01/25 15:21:33] INFO: Initializing hash boards
[2021/01/25 15:21:33] INFO: chain[1] - Initializing
[2021/01/25 15:21:33] INFO: chain[0] - Initializing
[2021/01/25 15:21:33] INFO: chain[2] - Initializing
[2021/01/25 15:21:49] INFO: chain[1] - 48 chips detected
[2021/01/25 15:21:51] INFO: chain[0] - 48 chips detected
[2021/01/25 15:21:52] INFO: chain[2] - 48 chips detected
[2021/01/25 15:21:59] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 15:21:59] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:21:59] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:22:31] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:22:47] INFO: Switching to immersion fan control
[2021/01/25 15:22:47] INFO: Start mining!
[2021/01/25 15:23:47] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:24:11] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:24:35] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:34:09] INFO: Detected 256 Mb of RAM
[2021/01/25 15:34:09] INFO: Switching to immersion fan control
[2021/01/25 15:34:15] INFO: Power ON
[2021/01/25 15:34:17] INFO: Starting FPGA queue
[2021/01/25 15:34:17] INFO: Initializing hash boards
[2021/01/25 15:34:17] INFO: chain[2] - Initializing
[2021/01/25 15:34:17] INFO: chain[1] - Initializing
[2021/01/25 15:34:17] INFO: chain[0] - Initializing
[2021/01/25 15:34:32] INFO: chain[2] - 48 chips detected
[2021/01/25 15:34:33] INFO: chain[1] - 48 chips detected
[2021/01/25 15:34:34] INFO: chain[0] - 48 chips detected
[2021/01/25 15:34:41] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 15:34:41] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:34:41] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:35:13] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:35:29] INFO: Switching to immersion fan control
[2021/01/25 15:35:29] INFO: Start mining!
[2021/01/25 15:36:29] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:36:53] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:37:17] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:37:41] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:38:48] INFO: Detected 256 Mb of RAM
[2021/01/25 15:38:48] INFO: Switching to immersion fan control
[2021/01/25 15:38:54] INFO: Power ON
[2021/01/25 15:38:56] INFO: Starting FPGA queue
[2021/01/25 15:38:56] INFO: Initializing hash boards
[2021/01/25 15:38:57] INFO: chain[0] - Initializing
[2021/01/25 15:38:57] INFO: chain[2] - Initializing
[2021/01/25 15:38:57] INFO: chain[1] - Initializing
[2021/01/25 15:39:13] INFO: chain[0] - 48 chips detected
[2021/01/25 15:39:14] INFO: chain[2] - 48 chips detected
[2021/01/25 15:39:16] INFO: chain[1] - 48 chips detected
[2021/01/25 15:39:23] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 15:39:23] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:39:23] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:39:54] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:40:10] INFO: Switching to immersion fan control
[2021/01/25 15:40:10] INFO: Start mining!
[2021/01/25 15:41:10] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:41:34] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:41:58] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:42:22] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:43:40] INFO: Detected 256 Mb of RAM
[2021/01/25 15:43:40] INFO: Switching to immersion fan control
[2021/01/25 15:43:46] INFO: Power ON
[2021/01/25 15:43:48] ERROR: src/power.c:161 Malformed power response
[2021/01/25 15:43:50] INFO: Starting FPGA queue
[2021/01/25 15:43:50] INFO: Initializing hash boards
[2021/01/25 15:43:50] INFO: chain[2] - Initializing
[2021/01/25 15:43:50] INFO: chain[1] - Initializing
[2021/01/25 15:43:50] INFO: chain[0] - Initializing
[2021/01/25 15:44:06] INFO: chain[2] - 48 chips detected
[2021/01/25 15:44:07] INFO: chain[1] - 48 chips detected
[2021/01/25 15:44:09] INFO: chain[0] - 48 chips detected
[2021/01/25 15:44:16] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 15:44:16] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:44:16] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:44:48] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:45:04] INFO: Switching to immersion fan control
[2021/01/25 15:45:04] INFO: Start mining!
[2021/01/25 15:46:04] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:46:27] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:46:52] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:47:16] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:48:40] INFO: Detected 256 Mb of RAM
[2021/01/25 15:48:40] INFO: Switching to immersion fan control
[2021/01/25 15:48:46] INFO: Power ON
[2021/01/25 15:48:48] INFO: Starting FPGA queue
[2021/01/25 15:48:48] INFO: Initializing hash boards
[2021/01/25 15:48:48] INFO: chain[2] - Initializing
[2021/01/25 15:48:48] INFO: chain[0] - Initializing
[2021/01/25 15:48:48] INFO: chain[1] - Initializing
[2021/01/25 15:49:04] INFO: chain[2] - 48 chips detected
[2021/01/25 15:49:06] INFO: chain[0] - 48 chips detected
[2021/01/25 15:49:08] INFO: chain[1] - 48 chips detected
[2021/01/25 15:49:15] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 15:49:15] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:49:15] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:49:47] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:50:03] INFO: Switching to immersion fan control
[2021/01/25 15:50:03] INFO: Start mining!
[2021/01/25 15:52:33] INFO: Detected 256 Mb of RAM
[2021/01/25 15:52:33] INFO: Switching to immersion fan control
[2021/01/25 15:52:39] INFO: Power ON
[2021/01/25 15:52:41] INFO: Starting FPGA queue
[2021/01/25 15:52:41] INFO: Initializing hash boards
[2021/01/25 15:52:41] INFO: chain[2] - Initializing
[2021/01/25 15:52:41] INFO: chain[1] - Initializing
[2021/01/25 15:52:41] INFO: chain[0] - Initializing
[2021/01/25 15:52:56] INFO: chain[2] - 48 chips detected
[2021/01/25 15:52:57] INFO: chain[1] - 48 chips detected
[2021/01/25 15:52:58] INFO: chain[0] - 48 chips detected
[2021/01/25 15:53:05] INFO: Start-up temperature is 41 C (min -15 C)
[2021/01/25 15:53:05] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:53:05] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:53:37] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:53:53] INFO: Switching to immersion fan control
[2021/01/25 15:53:53] INFO: Start mining!
[2021/01/25 15:54:53] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 15:55:17] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 15:55:41] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 15:56:05] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 15:57:33] INFO: Detected 256 Mb of RAM
[2021/01/25 15:57:33] INFO: Switching to immersion fan control
[2021/01/25 15:57:39] INFO: Power ON
[2021/01/25 15:57:41] INFO: Starting FPGA queue
[2021/01/25 15:57:41] INFO: Initializing hash boards
[2021/01/25 15:57:41] INFO: chain[1] - Initializing
[2021/01/25 15:57:41] INFO: chain[2] - Initializing
[2021/01/25 15:57:41] INFO: chain[0] - Initializing
[2021/01/25 15:57:57] INFO: chain[1] - 48 chips detected
[2021/01/25 15:57:58] INFO: chain[2] - 48 chips detected
[2021/01/25 15:58:00] INFO: chain[0] - 48 chips detected
[2021/01/25 15:58:07] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 15:58:07] INFO: Switching to manual fan control (100 %)
[2021/01/25 15:58:07] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 15:58:39] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 15:58:55] INFO: Switching to immersion fan control
[2021/01/25 15:58:55] INFO: Start mining!
[2021/01/25 15:59:55] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 16:00:18] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 16:00:43] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 16:01:38] INFO: Detected 256 Mb of RAM
[2021/01/25 16:01:38] INFO: Switching to immersion fan control
[2021/01/25 16:01:44] INFO: Power ON
[2021/01/25 16:01:46] INFO: Starting FPGA queue
[2021/01/25 16:01:46] INFO: Initializing hash boards
[2021/01/25 16:01:46] INFO: chain[1] - Initializing
[2021/01/25 16:01:46] INFO: chain[0] - Initializing
[2021/01/25 16:01:46] INFO: chain[2] - Initializing
[2021/01/25 16:02:02] INFO: chain[1] - 48 chips detected
[2021/01/25 16:02:04] INFO: chain[0] - 48 chips detected
[2021/01/25 16:02:05] INFO: chain[2] - 48 chips detected
[2021/01/25 16:02:12] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 16:02:12] INFO: Switching to manual fan control (100 %)
[2021/01/25 16:02:12] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 16:02:44] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 18:05:07] INFO: Detected 256 Mb of RAM
[2021/01/25 18:05:07] INFO: Switching to immersion fan control
[2021/01/25 18:05:13] INFO: Power ON
[2021/01/25 18:05:15] INFO: Starting FPGA queue
[2021/01/25 18:05:15] INFO: Initializing hash boards
[2021/01/25 18:05:15] INFO: chain[2] - Initializing
[2021/01/25 18:05:15] INFO: chain[1] - Initializing
[2021/01/25 18:05:15] INFO: chain[0] - Initializing
[2021/01/25 18:05:30] INFO: chain[2] - 48 chips detected
[2021/01/25 18:05:31] INFO: chain[1] - 48 chips detected
[2021/01/25 18:05:32] INFO: chain[0] - 48 chips detected
[2021/01/25 18:05:39] INFO: Start-up temperature is 40 C (min -15 C)
[2021/01/25 18:05:39] INFO: Switching to manual fan control (100 %)
[2021/01/25 18:05:39] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 18:06:11] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 18:06:27] INFO: Switching to immersion fan control
[2021/01/25 18:06:27] INFO: Start mining!
[2021/01/25 18:07:27] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 18:07:50] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 18:08:15] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 18:08:38] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 18:10:28] INFO: Detected 256 Mb of RAM
[2021/01/25 18:10:28] INFO: Switching to immersion fan control
[2021/01/25 18:10:34] INFO: Power ON
[2021/01/25 18:10:36] INFO: Starting FPGA queue
[2021/01/25 18:10:36] INFO: Initializing hash boards
[2021/01/25 18:10:36] INFO: chain[0] - Initializing
[2021/01/25 18:10:36] INFO: chain[1] - Initializing
[2021/01/25 18:10:36] INFO: chain[2] - Initializing
[2021/01/25 18:10:52] INFO: chain[0] - 48 chips detected
[2021/01/25 18:10:54] INFO: chain[1] - 48 chips detected
[2021/01/25 18:10:56] INFO: chain[2] - 48 chips detected
[2021/01/25 18:11:03] INFO: Start-up temperature is 42 C (min -15 C)
[2021/01/25 18:11:03] INFO: Switching to manual fan control (100 %)
[2021/01/25 18:11:03] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 18:11:35] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 18:11:51] INFO: Switching to immersion fan control
[2021/01/25 18:11:51] INFO: Start mining!
[2021/01/25 18:12:51] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 18:13:14] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 18:13:39] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 18:14:02] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 18:14:55] INFO: Detected 256 Mb of RAM
[2021/01/25 18:14:55] INFO: Switching to immersion fan control
[2021/01/25 18:15:02] INFO: Power ON
[2021/01/25 18:15:04] INFO: Starting FPGA queue
[2021/01/25 18:15:04] INFO: Initializing hash boards
[2021/01/25 18:15:04] INFO: chain[2] - Initializing
[2021/01/25 18:15:04] INFO: chain[1] - Initializing
[2021/01/25 18:15:04] INFO: chain[0] - Initializing
[2021/01/25 18:15:19] INFO: chain[2] - 48 chips detected
[2021/01/25 18:15:21] INFO: chain[1] - 48 chips detected
[2021/01/25 18:15:23] INFO: chain[0] - 48 chips detected
[2021/01/25 18:15:30] INFO: Start-up temperature is 43 C (min -15 C)
[2021/01/25 18:15:30] INFO: Switching to manual fan control (100 %)
[2021/01/25 18:15:30] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 18:16:01] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 18:16:18] INFO: Switching to immersion fan control
[2021/01/25 18:16:18] INFO: Start mining!
[2021/01/25 18:17:18] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 18:17:41] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 18:18:05] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 18:18:29] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 18:19:09] INFO: Detected 256 Mb of RAM
[2021/01/25 18:19:09] INFO: Switching to immersion fan control
[2021/01/25 18:19:15] INFO: Power ON
[2021/01/25 18:19:17] ERROR: src/power.c:161 Malformed power response
[2021/01/25 18:19:19] INFO: Starting FPGA queue
[2021/01/25 18:19:19] INFO: Initializing hash boards
[2021/01/25 18:19:19] INFO: chain[0] - Initializing
[2021/01/25 18:19:19] INFO: chain[1] - Initializing
[2021/01/25 18:19:19] INFO: chain[2] - Initializing
[2021/01/25 18:19:35] INFO: chain[0] - 48 chips detected
[2021/01/25 18:19:36] INFO: chain[1] - 48 chips detected
[2021/01/25 18:19:37] INFO: chain[2] - 48 chips detected
[2021/01/25 18:19:44] INFO: Start-up temperature is 43 C (min -15 C)
[2021/01/25 18:19:44] INFO: Switching to manual fan control (100 %)
[2021/01/25 18:19:44] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 18:20:15] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 18:20:31] INFO: Switching to immersion fan control
[2021/01/25 18:20:31] INFO: Start mining!
[2021/01/25 18:21:31] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 18:21:55] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 18:22:19] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 18:23:02] INFO: Detected 256 Mb of RAM
[2021/01/25 18:23:02] INFO: Switching to immersion fan control
[2021/01/25 18:23:04] INFO: Shutting down the miner
[2021/01/25 18:23:04] INFO: Power OFF
[2021/01/25 22:04:00] INFO: Detected 256 Mb of RAM
[2021/01/25 22:04:00] INFO: Switching to immersion fan control
[2021/01/25 22:04:06] INFO: Power ON
[2021/01/25 22:04:08] ERROR: src/power.c:161 Malformed power response
[2021/01/25 22:04:10] INFO: Starting FPGA queue
[2021/01/25 22:04:10] INFO: Initializing hash boards
[2021/01/25 22:04:10] INFO: chain[2] - Initializing
[2021/01/25 22:04:10] INFO: chain[1] - Initializing
[2021/01/25 22:04:10] INFO: chain[0] - Initializing
[2021/01/25 22:04:25] INFO: chain[2] - 48 chips detected
[2021/01/25 22:04:26] INFO: chain[1] - 48 chips detected
[2021/01/25 22:04:27] INFO: chain[0] - 48 chips detected
[2021/01/25 22:04:34] INFO: Start-up temperature is 40 C (min -15 C)
[2021/01/25 22:04:34] INFO: Switching to manual fan control (100 %)
[2021/01/25 22:04:34] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 22:05:06] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 22:05:22] INFO: Switching to immersion fan control
[2021/01/25 22:05:22] INFO: Start mining!
[2021/01/25 22:06:22] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 22:06:46] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 22:07:11] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 22:07:34] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/25 23:05:35] INFO: Detected 256 Mb of RAM
[2021/01/25 23:05:35] INFO: Switching to immersion fan control
[2021/01/25 23:05:42] INFO: Power ON
[2021/01/25 23:05:44] INFO: Starting FPGA queue
[2021/01/25 23:05:44] INFO: Initializing hash boards
[2021/01/25 23:05:44] INFO: chain[0] - Initializing
[2021/01/25 23:05:44] INFO: chain[1] - Initializing
[2021/01/25 23:05:44] INFO: chain[2] - Initializing
[2021/01/25 23:06:00] INFO: chain[0] - 48 chips detected
[2021/01/25 23:06:02] INFO: chain[1] - 48 chips detected
[2021/01/25 23:06:03] INFO: chain[2] - 48 chips detected
[2021/01/25 23:06:10] INFO: Start-up temperature is 43 C (min -15 C)
[2021/01/25 23:06:10] INFO: Switching to manual fan control (100 %)
[2021/01/25 23:06:10] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 23:06:41] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 23:06:57] INFO: Switching to immersion fan control
[2021/01/25 23:06:57] INFO: Start mining!
[2021/01/25 23:07:57] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 23:08:21] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 23:08:46] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 23:09:37] INFO: Detected 256 Mb of RAM
[2021/01/25 23:09:37] INFO: Switching to immersion fan control
[2021/01/25 23:09:43] INFO: Power ON
[2021/01/25 23:09:45] INFO: Starting FPGA queue
[2021/01/25 23:09:45] INFO: Initializing hash boards
[2021/01/25 23:09:45] INFO: chain[2] - Initializing
[2021/01/25 23:09:45] INFO: chain[0] - Initializing
[2021/01/25 23:09:45] INFO: chain[1] - Initializing
[2021/01/25 23:10:01] INFO: chain[2] - 48 chips detected
[2021/01/25 23:10:02] INFO: chain[0] - 48 chips detected
[2021/01/25 23:10:03] INFO: chain[1] - 48 chips detected
[2021/01/25 23:10:11] INFO: Start-up temperature is 43 C (min -15 C)
[2021/01/25 23:10:11] INFO: Switching to manual fan control (100 %)
[2021/01/25 23:10:11] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 23:10:42] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 23:10:58] INFO: Switching to immersion fan control
[2021/01/25 23:10:58] INFO: Start mining!
[2021/01/25 23:11:58] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 23:12:21] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 23:12:46] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 23:14:01] INFO: Detected 256 Mb of RAM
[2021/01/25 23:14:01] INFO: Switching to immersion fan control
[2021/01/25 23:14:07] INFO: Power ON
[2021/01/25 23:14:09] ERROR: src/power.c:161 Malformed power response
[2021/01/25 23:14:11] INFO: Starting FPGA queue
[2021/01/25 23:14:11] INFO: Initializing hash boards
[2021/01/25 23:14:11] INFO: chain[2] - Initializing
[2021/01/25 23:14:11] INFO: chain[1] - Initializing
[2021/01/25 23:14:11] INFO: chain[0] - Initializing
[2021/01/25 23:14:27] INFO: chain[2] - 48 chips detected
[2021/01/25 23:14:28] INFO: chain[1] - 48 chips detected
[2021/01/25 23:14:30] INFO: chain[0] - 48 chips detected
[2021/01/25 23:14:37] INFO: Start-up temperature is 43 C (min -15 C)
[2021/01/25 23:14:37] INFO: Switching to manual fan control (100 %)
[2021/01/25 23:14:37] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/25 23:15:09] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/25 23:15:25] INFO: Switching to immersion fan control
[2021/01/25 23:15:25] INFO: Start mining!
[2021/01/25 23:16:25] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/25 23:16:48] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/25 23:17:13] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/25 23:17:37] INFO: Changing voltage from 18800 to 18600 mV gradually
[2021/01/26 15:04:41] INFO: Detected 256 Mb of RAM
[2021/01/26 15:04:41] INFO: Switching to immersion fan control
[2021/01/26 15:04:47] INFO: Power ON
[2021/01/26 15:04:49] INFO: Starting FPGA queue
[2021/01/26 15:04:49] INFO: Initializing hash boards
[2021/01/26 15:04:49] INFO: chain[2] - Initializing
[2021/01/26 15:04:49] INFO: chain[1] - Initializing
[2021/01/26 15:04:49] INFO: chain[0] - Initializing
[2021/01/26 15:05:04] INFO: chain[2] - 48 chips detected
[2021/01/26 15:05:05] INFO: chain[1] - 48 chips detected
[2021/01/26 15:05:06] INFO: chain[0] - 48 chips detected
[2021/01/26 15:05:13] INFO: Start-up temperature is 40 C (min -15 C)
[2021/01/26 15:05:13] INFO: Switching to manual fan control (100 %)
[2021/01/26 15:05:13] INFO: Changing voltage from 21000 to 19400 mV gradually
[2021/01/26 15:05:45] INFO: Raising freq from 50 to 700 Mhz gradually
[2021/01/26 15:06:01] INFO: Switching to immersion fan control
[2021/01/26 15:06:01] INFO: Start mining!
[2021/01/26 15:07:01] INFO: Changing voltage from 19400 to 19200 mV gradually
[2021/01/26 15:07:25] INFO: Changing voltage from 19200 to 19000 mV gradually
[2021/01/26 15:07:49] INFO: Changing voltage from 19000 to 18800 mV gradually
[2021/01/26 15:08:13] INFO: Changing voltage from 18800 to 18600 mV gradually
Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: