S17 Pro no longer hashing | Bitcointalksearch.org

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

You followed up thank you keep posting you now have merits so you will soon be a jr member not a newbie.

agilmore

jr. member

Activity: 40

Merit: 13

Thanks all. To verify that it was a fan issue, I moved a working fan connector to a different set of pins and saw that the list of working fans listed within the kernel log was updated to show the new fan location. I purchased and installed the fan below. That fixed my problem.

https://www.ebay.com/itm/6500RPM-Cooling-Fan-Replacement-4-pin-Connector-For-Antminer-Bitmain-S7-S9-Black/112634675926

mikeywith

legendary

Activity: 2394

Merit: 6581

be constructive or S.T.F.U

Before you waste your money and time on a new fan, you must first confirm that the control board is actually correctly reading the FANS' rpm by swapping fan 0 and fan 1

Code:

2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 0, fan_speed = 0

The S17 pro has 4 fans labeled as Fan0, Fan1,Fan2 and Fan3, after swapping the cable from fan0 to fan1 you will get one of two results

1-

Code:

2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 0, fan_speed = 5xxx
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 1, fan_speed = 0

This indicates the original fan0 (now fan1) is bad and needs a replacement.

2-

Code:

2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 0, fan_speed = 0
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 1, fan_speed = 5xxx

This indicates the fan has no problem but the control board fails to detect the fan due to a faulty socket or bad firmware.

also in your initial post, there is a pool-related issue, you must use a working pool, if you are using nicehash which is known to have issues with these new miners, use another pool, actually use two pools just incase.

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: agilmore on February 07, 2020, 07:13:32 PM

Thanks all. I'll replace the fan and report back.

Good luck with this. Please post results. TIA

agilmore

jr. member

Activity: 40

Merit: 13

Thanks all. I'll replace the fan and report back.

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

please read all of this right to the end.

you have a bad fan it may spin but it does not register the rpm some times this happens.

you need a fan

are you usa based?

this should work

https://www.ebay.com/itm/6500RPM-Cooling-Fan-Replacement-4-pin-Connector-For-Antminer-Bitmain-S7-S9-Black/112634675926?

note any I give you should work I don't know the sellers

https://www.amazon.com/Matoen-6000RPM-Replacement-Connector-Antminer/dp/B078PBG2B2

you may or may not need these

https://www.amazon.com/Dayree-Extension-Connector-Extending-Compatible/dp/B0788Q4TND

buy these from bitmain may be very slow

you will need both parts

https://shop.bitmain.com/product/detail?pid=000201910151107519921qKMCqzJ06A8

https://shop.bitmain.com/product/detail?pid=00020191021143636786sS54N4Xt0679

Lastly

try to do this test switch the bad fan with a good one.

if the problem follows the fan you have a bad fan

if the problem stays with the fan power slot you have a bad controller

controllers are sold out https://shop.bitmain.com/product/detail?pid=000201908151010180899X61guRp068C for Control board for S17, S17Pro, T17

agilmore

jr. member

Activity: 40

Merit: 13

Here's the latest log:

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203612K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25764K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12724K (cce94000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 306349061
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 038216C1-D266-46DA-A76E-C04B142933A3, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2053/1021, WL threshold: 4096, image sequence number: 1751317449
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 51C7124B-A562-4AA0-948B-184BE8DB9030, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
2020-02-07 23:11:01 driver-btm-api.c:515:init_freq_mode: This is scan-user version
2020-02-07 23:11:01 driver-btm-api.c:1871:bitmain_soc_init: opt_multi_version     = 1
2020-02-07 23:11:01 driver-btm-api.c:1872:bitmain_soc_init: opt_bitmain_ab        = 1
2020-02-07 23:11:01 driver-btm-api.c:1873:bitmain_soc_init: opt_bitmain_work_mode = 2
2020-02-07 23:11:01 driver-btm-api.c:1874:bitmain_soc_init: Miner compile time: Wed Dec 25 09:47:07 CST 2019 type: Antminer S17
2020-02-07 23:11:01 driver-btm-api.c:1875:bitmain_soc_init: commit version: b1e11d0 2019-12-24 22:26:20, build by: lol 2019-12-25 09:59:19
2020-02-07 23:11:01 driver-btm-api.c:1664:show_sn: no SN got, please write SN to /nvdata/sn
2020-02-07 23:11:01 driver-btm-api.c:1013:miner_device_init: Detect 256MB control board of XILINX
2020-02-07 23:11:01 driver-btm-api.c:961:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-02-07 23:11:07 driver-btm-api.c:945:init_miner_version: miner ID : 81248c2e5740885c
2020-02-07 23:11:07 driver-btm-api.c:951:init_miner_version: FPGA Version = 0xB013
2020-02-07 23:11:13 thread.c:699:create_read_nonce_reg_thread: create thread
2020-02-07 23:11:13 driver-btm-api.c:589:get_product_id: product_id[0] = 0
2020-02-07 23:11:13 driver-btm-api.c:589:get_product_id: product_id[1] = 0
2020-02-07 23:11:13 driver-btm-api.c:589:get_product_id: product_id[2] = 0
2020-02-07 23:11:13 driver-btm-api.c:533:_set_project_type: project:0
2020-02-07 23:11:13 driver-btm-api.c:558:_set_project_type: Project type: Antminer S17 Pro
2020-02-07 23:11:13 driver-btm-api.c:569:dump_pcb_bom_version: Chain [0] PCB Version: 0x0101
2020-02-07 23:11:13 driver-btm-api.c:570:dump_pcb_bom_version: Chain [0] BOM Version: 0x0103
2020-02-07 23:11:13 driver-btm-api.c:569:dump_pcb_bom_version: Chain [1] PCB Version: 0x0101
2020-02-07 23:11:13 driver-btm-api.c:570:dump_pcb_bom_version: Chain [1] BOM Version: 0x0103
2020-02-07 23:11:13 driver-btm-api.c:569:dump_pcb_bom_version: Chain [2] PCB Version: 0x0101
2020-02-07 23:11:13 driver-btm-api.c:570:dump_pcb_bom_version: Chain [2] BOM Version: 0x0103
2020-02-07 23:11:33 fan.c:83:check_fan_status: Error, fan lost, only find 3 (< 4)
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 0, fan_speed = 0
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 1, fan_speed = 5880
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 2, fan_speed = 4800
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 3, fan_speed = 4920
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 4, fan_speed = 0
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 5, fan_speed = 0
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 6, fan_speed = 0
2020-02-07 23:11:33 fan.c:86:check_fan_status: fan_id = 7, fan_speed = 0
2020-02-07 23:11:33 driver-btm-api.c:197:set_miner_status: ERROR_FAN_LOST
2020-02-07 23:11:33 driver-btm-api.c:138:stop_mining: stop mining: fan lost
2020-02-07 23:11:33 thread.c:744:cancel_read_nonce_reg_thread: cancel thread
2020-02-07 23:11:33 driver-btm-api.c:124:killall_hashboard: ****power off hashboard****

Is the fan issue causing my problem? I can see all 4 fans spinning. The miner Status page is empty.

Here's other info:

Code:

Miner Type	Antminer S17 Pro
Hostname	antMiner
Model	GNU/Linux
Hardware Version	Socket connect failed: Connection refused
Kernel Version	Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
File System Version	Wed Dec 25 09:47:07 CST 2019

VRobb

hero member

Activity: 1610

Merit: 538

I'm in BTC XTC

Five lines up from the bottom shows:

2020-01-25 20:58:25 driver-btm-api.c:1648:check_pool_worker: No valid pools, please configure them first!

Nothing happened to the pool info, did it? Maybe got garbled, or the dreaded hidden at the end?

agilmore

jr. member

Activity: 40

Merit: 13

Hi, My miner was working fine, but then stopped working. See the screenshots. Any suggestions?

The miner status page doesn't contain hashing info.

Code:

HW Version:  Socket connect failed: Connection refused.

In the log, i noticed some a single fan failure.

How can i attach screenshots? lol

Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203612K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25764K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12724K (cce94000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 306349061
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 038216C1-D266-46DA-A76E-C04B142933A3, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2053/1021, WL threshold: 4096, image sequence number: 1751317449
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 51C7124B-A562-4AA0-948B-184BE8DB9030, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
2020-01-25 20:58:13 driver-btm-api.c:515:init_freq_mode: This is scan-user version
2020-01-25 20:58:13 driver-btm-api.c:1871:bitmain_soc_init: opt_multi_version     = 1
2020-01-25 20:58:13 driver-btm-api.c:1872:bitmain_soc_init: opt_bitmain_ab        = 1
2020-01-25 20:58:13 driver-btm-api.c:1873:bitmain_soc_init: opt_bitmain_work_mode = 2
2020-01-25 20:58:13 driver-btm-api.c:1874:bitmain_soc_init: Miner compile time: Wed Dec 25 09:47:07 CST 2019 type: Antminer S17
2020-01-25 20:58:13 driver-btm-api.c:1875:bitmain_soc_init: commit version: b1e11d0 2019-12-24 22:26:20, build by: lol 2019-12-25 09:59:19
2020-01-25 20:58:13 driver-btm-api.c:1664:show_sn: no SN got, please write SN to /nvdata/sn
2020-01-25 20:58:13 driver-btm-api.c:1013:miner_device_init: Detect 256MB control board of XILINX
2020-01-25 20:58:13 driver-btm-api.c:961:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2020-01-25 20:58:19 driver-btm-api.c:945:init_miner_version: miner ID : 81248c2e5740885c
2020-01-25 20:58:19 driver-btm-api.c:951:init_miner_version: FPGA Version = 0xB013
2020-01-25 20:58:25 thread.c:699:create_read_nonce_reg_thread: create thread
2020-01-25 20:58:25 driver-btm-api.c:589:get_product_id: product_id[0] = 0
2020-01-25 20:58:25 driver-btm-api.c:589:get_product_id: product_id[1] = 0
2020-01-25 20:58:25 driver-btm-api.c:589:get_product_id: product_id[2] = 0
2020-01-25 20:58:25 driver-btm-api.c:533:_set_project_type: project:0
2020-01-25 20:58:25 driver-btm-api.c:558:_set_project_type: Project type: Antminer S17 Pro
2020-01-25 20:58:25 driver-btm-api.c:569:dump_pcb_bom_version: Chain [0] PCB Version: 0x0101
2020-01-25 20:58:25 driver-btm-api.c:570:dump_pcb_bom_version: Chain [0] BOM Version: 0x0103
2020-01-25 20:58:25 driver-btm-api.c:569:dump_pcb_bom_version: Chain [1] PCB Version: 0x0101
2020-01-25 20:58:25 driver-btm-api.c:570:dump_pcb_bom_version: Chain [1] BOM Version: 0x0103
2020-01-25 20:58:25 driver-btm-api.c:569:dump_pcb_bom_version: Chain [2] PCB Version: 0x0101
2020-01-25 20:58:25 driver-btm-api.c:570:dump_pcb_bom_version: Chain [2] BOM Version: 0x0103
2020-01-25 20:58:25 driver-btm-api.c:1648:check_pool_worker: No valid pools, please configure them first!
2020-01-25 20:58:25 driver-btm-api.c:197:set_miner_status: ERROR_SOC_INIT
2020-01-25 20:58:25 driver-btm-api.c:138:stop_mining: stop mining: soc init failed!
2020-01-25 20:58:25 thread.c:744:cancel_read_nonce_reg_thread: cancel thread
2020-01-25 20:58:25 driver-btm-api.c:124:killall_hashboard: ****power off hashboard****

Topic: S17 Pro no longer hashing (Read 275 times)