Hello Renatopinto,
Sorry for delay.
This is classic TTL cable: https://www.ebay.fr/itm/400708482567
Plug TTL Cable on your PC and lets windows install driver. Go in Windows bar and in "Device Manager" and in "PORT & COM" you will see your cable and his PORT attributed.
After that you need to have software to manage result of signal (on terminal), for exemple on Windows you have: MobaXterm
Launch MobaXTerm -> Session -> Select Serial ->Select right COM port -> Speed 15600 bps and RUN
Plug your TTL cable on controal board (TX, GND, RX) and turn on the board.
and all result will appear on your screen !
Best regards
Topic: S19 Amlogic control board brick ? (Read 250 times)
Hello, how are you?
I have a problem with my Control Board, I did a bad update. And the same happened with others that keep restarting.
Can you help me with the question I asked on the Forum?
. https://bitcointalksearch.org/topic/m.63041239
How can I get the TTL cable and test it? Can you show me the cable model and how to connect it?
I'm trying to buy a new card, but the time the machine will be offline is bad.
Thanks and best regards,
I have a problem with my Control Board, I did a bad update. And the same happened with others that keep restarting.
Can you help me with the question I asked on the Forum?
. https://bitcointalksearch.org/topic/m.63041239
How can I get the TTL cable and test it? Can you show me the cable model and how to connect it?
I'm trying to buy a new card, but the time the machine will be offline is bad.
Thanks and best regards,
Oh yes !
Info of PHY chip of an AMLOGIC C76 control board is:
SMSC 8710A
and link is this: https://fr.aliexpress.com/item/1924473024.html?spm=a2g0o.order_detail.order_detail_item.3.6bba7d56CYPPDm&gatewayAdapt=glo2fra
If anyone in UE want a piece, let me know ! (to avoid 3weeks delivery)
Info of PHY chip of an AMLOGIC C76 control board is:
SMSC 8710A
and link is this: https://fr.aliexpress.com/item/1924473024.html?spm=a2g0o.order_detail.order_detail_item.3.6bba7d56CYPPDm&gatewayAdapt=glo2fra
If anyone in UE want a piece, let me know ! (to avoid 3weeks delivery)
Hello everyone,
So I received the PHY chips, and I can confirm....that it came from there.
So in conclusion, if you have the DDR blinks which are faintly lit and the ETH socket blinks off and in your logs via TTL cable you have code similar to mine up to "eth%d: No PHY found".
there's a good chance that the PHY part is responsible for the control board not booting. Because it's one of the last parts to boot (after the CPU in any case).
The following diagram gave me a clue, as it clearly shows that the PHY module controls the ETHERNET, the LEDS and the magnetic.
I hope this has helped some people! (but I curse AMLOGIC anyway, it's poorly documented and fragile as hell).
I'm glad that you fixed the issue the only clue that I could see from your previous logs is the ethernet or a chip that is responsible for Ethernet.So I received the PHY chips, and I can confirm....that it came from there.
So in conclusion, if you have the DDR blinks which are faintly lit and the ETH socket blinks off and in your logs via TTL cable you have code similar to mine up to "eth%d: No PHY found".
there's a good chance that the PHY part is responsible for the control board not booting. Because it's one of the last parts to boot (after the CPU in any case).
The following diagram gave me a clue, as it clearly shows that the PHY module controls the ETHERNET, the LEDS and the magnetic.
I hope this has helped some people! (but I curse AMLOGIC anyway, it's poorly documented and fragile as hell).
Why not also post the source where you buy PHY chips? Can you share the code name of the chip you can read it under the chip as I couldn't find it on Zeusbtc if I type PHy.
Hello everyone,
So I received the PHY chips, and I can confirm....that it came from there.
So in conclusion, if you have the DDR blinks which are faintly lit and the ETH socket blinks off and in your logs via TTL cable you have code similar to mine up to "eth%d: No PHY found".
there's a good chance that the PHY part is responsible for the control board not booting. Because it's one of the last parts to boot (after the CPU in any case).
The following diagram gave me a clue, as it clearly shows that the PHY module controls the ETHERNET, the LEDS and the magnetic.
I hope this has helped some people! (but I curse AMLOGIC anyway, it's poorly documented and fragile as hell).
So I received the PHY chips, and I can confirm....that it came from there.
So in conclusion, if you have the DDR blinks which are faintly lit and the ETH socket blinks off and in your logs via TTL cable you have code similar to mine up to "eth%d: No PHY found".
there's a good chance that the PHY part is responsible for the control board not booting. Because it's one of the last parts to boot (after the CPU in any case).
The following diagram gave me a clue, as it clearly shows that the PHY module controls the ETHERNET, the LEDS and the magnetic.
I hope this has helped some people! (but I curse AMLOGIC anyway, it's poorly documented and fragile as hell).
hello, i have a same problem on my Amlogic board ... after update its totaly bricked...
Me too, i look in TTL, i see boot correctly but no ethernet exange...
i work for this, and i find the problem, see my website, and try my SD S19J-PRO AML Stock . and paste your comment if work or not
Me too, i look in TTL, i see boot correctly but no ethernet exange...
i work for this, and i find the problem, see my website, and try my SD S19J-PRO AML Stock . and paste your comment if work or not
All right! I ordered a set of PHY chip, it will arrive in 15 days.
See you
See you
Nice work. Please get back to us and let us know if that chip fixes it.
After careful analysis, the last line corresponds to "No Phy Found". The rest of the logs show a healthy boot and NAND. So I started looking at the PHY chip.
On the internet you can find this diagram:
I conclude that since my leds and eth plug are off and PHY is controlling this, the little PHY chip is dead.
So I unsoldered the part and ran the analysis, and the logs are exactly the same, confirming my point.
I'll order the part and keep you posted.
On the internet you can find this diagram:
I conclude that since my leds and eth plug are off and PHY is controlling this, the little PHY chip is dead.
So I unsoldered the part and ran the analysis, and the logs are exactly the same, confirming my point.
I'll order the part and keep you posted.
Based on the logs during flashing it said burn success.
Have you used any commands during flashing through the TTL method?
There is another method to flash the unit through TTL but I do not know if the commands will work on the s19j pro.
Can you try this method Recovery Method of Serial Port Bitmain also have the same guide but the problem is they didn't include the command lines? That is I think the last step you haven't tried yet(sending command during flashing).
Have you used any commands during flashing through the TTL method?
There is another method to flash the unit through TTL but I do not know if the commands will work on the s19j pro.
Can you try this method Recovery Method of Serial Port Bitmain also have the same guide but the problem is they didn't include the command lines? That is I think the last step you haven't tried yet(sending command during flashing).
Hello,
I went straight to the TTL step because all the previous steps (the IpReport button, the flash with microUSB with the little green light that comes on after 30sec) had already been done but the restart doesn't happen. So I decided to use mobaxterm and a TTL cable to check what was happening in the control board, and I've posted the results above. I've also attached below the TTL log during boot with the microUSB for firmware.
I went straight to the TTL step because all the previous steps (the IpReport button, the flash with microUSB with the little green light that comes on after 30sec) had already been done but the restart doesn't happen. So I decided to use mobaxterm and a TTL cable to check what was happening in the control board, and I've posted the results above. I've also attached below the TTL log during boot with the microUSB for firmware.
Code:
AXG:BL1:d1dbf2:a4926f;FEAT:F0DC31BC:2000;POC:F;EMMC:800;NAND:0;READ:0;0.0;0.0;CHK:0;
sdio debug board detected
TE: 136410
BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh
set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 17 00 2f 2a 11 44 1b 00 37 26 0c 41 00 00 00 00 00 00 00 00 00 00 00 00 721 - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE: BL31: v1.3(release):3edeb02
NOTICE: BL31: Built : 16:43:54, Apr 14 2020
NOTICE: BL31: AXG secure boot!
NOTICE: BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015880 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12
DRAM: 256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC: aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In: serial
Out: serial
Err: serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
[fat]Filesize is 0x25aB[0M]
[FAT_ERR]L1208,offset(0x0) + wantsz(0x6c40) > filesize(0x25a)
ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_img_decoder.c)L104:want to read 27712, but 0
[MSG]cfg[aml_sdc_burn.ini] not valid aml pkg, parse it as ini
[MSG]ini sz 0x25aB
[fat]Filesize is 0x25aB[0M]
[fat]0x:leftSz 25a < BPS 1000, gotSz 25a
=========sdc_burn_paras=====>>>
[common]
erase_bootloader = 1
erase_flash = 1
reboot = 0x1
key_overwrite = 0x0
erase_ddr_para = 0x0
[burn_ex]
package = aml_upgrade_package_enc.img
media =
[burn_parts]
burn_num = 0
<<<<=====sdc_burn_paras======
[fat]Filesize is 0x15ee8a8B[21M]
[fat]0x:leftSz c40 < BPS 1000, gotSz 6c40
[MSG]image version [0x00000002]
[MSG]SecureEnabled, use meson1_ENC
[fat]Seek 0x192300 from 0x6c40
[MSG]itemSizeNotAligned 0xd00
[MSG]align 4 mmc read... [fat]0x:leftSz 720 < BPS 1000, gotSz 7420
[MSG]Down(mem) part(dtb) sz(0x7420) fmt(normal)
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x7420
[MSG]Burn complete
[MSG]Exit before re-init
command: store exit
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
start dts,buffer=0000000001000000,dt_addr=0000000001010800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x3ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x3ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x3ff2800
EMMC init failed
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
XXXXXXX======enter NAND boot======XXXXXX
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
Amlogic multi-DTB tool
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
whole chip
do_nand(): off 0, size 268435456
Erasing at 0x0 -- 0% complete.aml_nand_erase_cmd blk 0x14 is protected
Erasing at 0x280000 -- 1% complete.aml_nand_erase_cmd blk 0x15 is protected
aml_nand_erase_cmd blk 0x16 is protected
aml_nand_erase_cmd blk 0x17 is protected
Erasing at 0xffe0000 -- 100% complete.
OK
[burn_parts]
burn_num = 3
burn_part0 = _aml_dtb
burn_part1 = boot
burn_part2 = recovery
[MSG]=====>To burn part [_aml_dtb]
[MSG]itemSizeNotAligned 0xd00
[MSG]Down(store) part(_aml_dtb) sz(0x7420) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[MSG]itemSizeNotAligned 0xd00, itemSizePreload 0xd00
[fat]0x:leftSz 720 < BPS 1000, gotSz 6720
[MSG]Burn Start...
[MSG]cmd[store erase partition _aml_dtb]
0x000000000000-0x000000200000 : "bootloader"
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
--- find_dev_and_part ---
id = _aml_dtb
[MSG]optimus_download_dtb_image:dataSzReceived=0x7420
sub cmd dtb
new argv[1] dtb_erase
do_dtb_ops(): argc 2
arg 0: amlnf
arg 1: dtb_erase
do_dtb_ops() erase
amlnf_dtb_erase: ####
erasing ndtb:
erasing valid info block: 520000
erasing free info block: 500000
erasing free info block: 540000
erasing free info block: 560000
do_dtb_ops() erase Okay
[store]To run cmd[amlnf dtb_write 0x00000000013ff300 0x40000]
sub cmd dtb
new argv[1] dtb_write
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_write
arg 2: 0x00000000013ff300
arg 3: 0x40000
do_dtb_ops() write
amlnf_dtb_save: ####
warnning!!! amlnf_dtb_save: length too much
aml_nand_save_rsv_info:685, ndtb: valid=1, pages=64
release_free_node 112: bitmap=ffffff
release_free_node 125: bitmap=fbffff
aml_nand_save_rsv_info:750,save info to 500000
do_dtb_ops(): 262144 bytes write : OK
[MSG]Burn complete
[store]To run cmd[amlnf dtb_read 0x0000000001400000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x0000000001400000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 500000
do_dtb_ops(): 262144 bytes read : OK
[MSG]VERIFY OK
[MSG]=====>To burn part [boot]
[fat]Seek 0x3295b0 from 0x199750
[MSG]itemSizeNotAligned 0xa50
[MSG]flash LOGIC partCap 0x400000000B
[MSG]Down(store) part(boot) sz(0xc2c200) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 13
[MSG]itemSizeNotAligned 0xa50, itemSizePreload 0xa50
[fat]0x:leftSz 7b0 < BPS 1000, gotSz 2b7b0
[MSG]Burn Start...
[MSG]cmd[store erase partition boot]
mtdparts_init() 848, already init
--- find_dev_and_part ---
id = boot
found boot @ 4/7do_nand(): off 35651584, size 33554432
Erasing at 0x41e0000 -- 100% complete.
OK
[burnup]Wr:Up sz 0xc2c200 to align 0x1000
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part boot in fmt normal
[burnup]Rd:Up sz 0x2c200 to align 0x1000
[MSG]Verify End
[MSG]VERIFY OK
[MSG]=====>To burn part [recovery]
[fat]Seek 0x1024678 from 0xf557e0
[MSG]itemSizeNotAligned 0x988
[MSG]flash LOGIC partCap 0x200000000B
[MSG]Down(store) part(recovery) sz(0x5ca200) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 6
[MSG]itemSizeNotAligned 0x988, itemSizePreload 0x988
[fat]0x:leftSz 878 < BPS 1000, gotSz c9878
[MSG]Burn Start...
[MSG]cmd[store erase partition recovery]
mtdparts_init() 848, already init
--- find_dev_and_part ---
id = recovery
found recovery @ 3/7do_nand(): off 18874368, size 16777216
Erasing at 0x21e0000 -- 100% complete.
OK
[burnup]Wr:Up sz 0x5ca200 to align 0x1000
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part recovery in fmt normal
[burnup]Rd:Up sz 0x1ca200 to align 0x1000
[MSG]Verify End
[MSG]VERIFY OK
[MSG]=====>To burn part [bootloader]
[MSG]itemSizeNotAligned 0x820
[MSG]Down(store) part(bootloader) sz(0xc7e00) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[MSG]itemSizeNotAligned 0x820, itemSizePreload 0x820
[fat]0x:leftSz 5e0 < BPS 1000, gotSz c75e0
[MSG]Burn Start...
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 0
do_rom_ops() erase
Erasing at 0x20000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 0
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 1
do_rom_ops() erase
Erasing at 0x60000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 1
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 2
do_rom_ops() erase
Erasing at 0xa0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 2
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 3
do_rom_ops() erase
Erasing at 0xe0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 3
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 4
do_rom_ops() erase
Erasing at 0x120000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 4
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 5
do_rom_ops() erase
Erasing at 0x160000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 5
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 6
do_rom_ops() erase
Erasing at 0x1a0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 6
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 7
do_rom_ops() erase
Erasing at 0x1e0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 7
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 0
do_fip_ops() erase, base 2
Erasing at 0x9e0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 0
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 1
do_fip_ops() erase, base 2
Erasing at 0xbe0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 200000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 2
do_fip_ops() erase, base 2
Erasing at 0xde0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 400000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 3
do_fip_ops() erase, base 2
Erasing at 0xfe0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 600000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
[MSG]Burn complete
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 0
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 1
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 2
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 3
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd fip
new argv[1] fip_read
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_read
arg 2: 0x000000000dec7e50
arg 3: 0
arg 4: 0xbbe00
do_fip_ops() read
sub cmd fip
new argv[1] fip_read
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_read
arg 2: 0x000000000dec7e50
arg 3: 200000
arg 4: 0xbbe00
do_fip_ops() read
[MSG]VERIFY OK
[MSG]Set upgrade_step to 1
Saving Environment to aml-storage...
uboot env amlnf_env_save : ####
aml_nand_save_rsv_info:685, nenv: valid=1, pages=32
release_free_node 112: bitmap=ffffff
release_free_node 125: bitmap=fffff7
aml_nand_save_rsv_info:750,save info to 300000
[MSG]to close image
[MSG]======sdc burn SUCCESS.
gpio: pin GPIOA_16 (gpio 56) value is 1
sdio debug board detected
TE: 136410
BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh
set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 17 00 2f 2a 11 44 1b 00 37 26 0c 41 00 00 00 00 00 00 00 00 00 00 00 00 721 - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE: BL31: v1.3(release):3edeb02
NOTICE: BL31: Built : 16:43:54, Apr 14 2020
NOTICE: BL31: AXG secure boot!
NOTICE: BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015880 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12
DRAM: 256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC: aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In: serial
Out: serial
Err: serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
[fat]Filesize is 0x25aB[0M]
[FAT_ERR]L1208,offset(0x0) + wantsz(0x6c40) > filesize(0x25a)
ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_img_decoder.c)L104:want to read 27712, but 0
[MSG]cfg[aml_sdc_burn.ini] not valid aml pkg, parse it as ini
[MSG]ini sz 0x25aB
[fat]Filesize is 0x25aB[0M]
[fat]0x:leftSz 25a < BPS 1000, gotSz 25a
=========sdc_burn_paras=====>>>
[common]
erase_bootloader = 1
erase_flash = 1
reboot = 0x1
key_overwrite = 0x0
erase_ddr_para = 0x0
[burn_ex]
package = aml_upgrade_package_enc.img
media =
[burn_parts]
burn_num = 0
<<<<=====sdc_burn_paras======
[fat]Filesize is 0x15ee8a8B[21M]
[fat]0x:leftSz c40 < BPS 1000, gotSz 6c40
[MSG]image version [0x00000002]
[MSG]SecureEnabled, use meson1_ENC
[fat]Seek 0x192300 from 0x6c40
[MSG]itemSizeNotAligned 0xd00
[MSG]align 4 mmc read... [fat]0x:leftSz 720 < BPS 1000, gotSz 7420
[MSG]Down(mem) part(dtb) sz(0x7420) fmt(normal)
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x7420
[MSG]Burn complete
[MSG]Exit before re-init
command: store exit
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
start dts,buffer=0000000001000000,dt_addr=0000000001010800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x3ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x3ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x3ff2800
EMMC init failed
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
XXXXXXX======enter NAND boot======XXXXXX
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
Amlogic multi-DTB tool
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
whole chip
do_nand(): off 0, size 268435456
Erasing at 0x0 -- 0% complete.aml_nand_erase_cmd blk 0x14 is protected
Erasing at 0x280000 -- 1% complete.aml_nand_erase_cmd blk 0x15 is protected
aml_nand_erase_cmd blk 0x16 is protected
aml_nand_erase_cmd blk 0x17 is protected
Erasing at 0xffe0000 -- 100% complete.
OK
[burn_parts]
burn_num = 3
burn_part0 = _aml_dtb
burn_part1 = boot
burn_part2 = recovery
[MSG]=====>To burn part [_aml_dtb]
[MSG]itemSizeNotAligned 0xd00
[MSG]Down(store) part(_aml_dtb) sz(0x7420) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[MSG]itemSizeNotAligned 0xd00, itemSizePreload 0xd00
[fat]0x:leftSz 720 < BPS 1000, gotSz 6720
[MSG]Burn Start...
[MSG]cmd[store erase partition _aml_dtb]
0x000000000000-0x000000200000 : "bootloader"
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
--- find_dev_and_part ---
id = _aml_dtb
[MSG]optimus_download_dtb_image:dataSzReceived=0x7420
sub cmd dtb
new argv[1] dtb_erase
do_dtb_ops(): argc 2
arg 0: amlnf
arg 1: dtb_erase
do_dtb_ops() erase
amlnf_dtb_erase: ####
erasing ndtb:
erasing valid info block: 520000
erasing free info block: 500000
erasing free info block: 540000
erasing free info block: 560000
do_dtb_ops() erase Okay
[store]To run cmd[amlnf dtb_write 0x00000000013ff300 0x40000]
sub cmd dtb
new argv[1] dtb_write
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_write
arg 2: 0x00000000013ff300
arg 3: 0x40000
do_dtb_ops() write
amlnf_dtb_save: ####
warnning!!! amlnf_dtb_save: length too much
aml_nand_save_rsv_info:685, ndtb: valid=1, pages=64
release_free_node 112: bitmap=ffffff
release_free_node 125: bitmap=fbffff
aml_nand_save_rsv_info:750,save info to 500000
do_dtb_ops(): 262144 bytes write : OK
[MSG]Burn complete
[store]To run cmd[amlnf dtb_read 0x0000000001400000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x0000000001400000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 500000
do_dtb_ops(): 262144 bytes read : OK
[MSG]VERIFY OK
[MSG]=====>To burn part [boot]
[fat]Seek 0x3295b0 from 0x199750
[MSG]itemSizeNotAligned 0xa50
[MSG]flash LOGIC partCap 0x400000000B
[MSG]Down(store) part(boot) sz(0xc2c200) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 13
[MSG]itemSizeNotAligned 0xa50, itemSizePreload 0xa50
[fat]0x:leftSz 7b0 < BPS 1000, gotSz 2b7b0
[MSG]Burn Start...
[MSG]cmd[store erase partition boot]
mtdparts_init() 848, already init
--- find_dev_and_part ---
id = boot
found boot @ 4/7do_nand(): off 35651584, size 33554432
Erasing at 0x41e0000 -- 100% complete.
OK
[burnup]Wr:Up sz 0xc2c200 to align 0x1000
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part boot in fmt normal
[burnup]Rd:Up sz 0x2c200 to align 0x1000
[MSG]Verify End
[MSG]VERIFY OK
[MSG]=====>To burn part [recovery]
[fat]Seek 0x1024678 from 0xf557e0
[MSG]itemSizeNotAligned 0x988
[MSG]flash LOGIC partCap 0x200000000B
[MSG]Down(store) part(recovery) sz(0x5ca200) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 6
[MSG]itemSizeNotAligned 0x988, itemSizePreload 0x988
[fat]0x:leftSz 878 < BPS 1000, gotSz c9878
[MSG]Burn Start...
[MSG]cmd[store erase partition recovery]
mtdparts_init() 848, already init
--- find_dev_and_part ---
id = recovery
found recovery @ 3/7do_nand(): off 18874368, size 16777216
Erasing at 0x21e0000 -- 100% complete.
OK
[burnup]Wr:Up sz 0x5ca200 to align 0x1000
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part recovery in fmt normal
[burnup]Rd:Up sz 0x1ca200 to align 0x1000
[MSG]Verify End
[MSG]VERIFY OK
[MSG]=====>To burn part [bootloader]
[MSG]itemSizeNotAligned 0x820
[MSG]Down(store) part(bootloader) sz(0xc7e00) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[MSG]itemSizeNotAligned 0x820, itemSizePreload 0x820
[fat]0x:leftSz 5e0 < BPS 1000, gotSz c75e0
[MSG]Burn Start...
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 0
do_rom_ops() erase
Erasing at 0x20000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 0
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 1
do_rom_ops() erase
Erasing at 0x60000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 1
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 2
do_rom_ops() erase
Erasing at 0xa0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 2
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 3
do_rom_ops() erase
Erasing at 0xe0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 3
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 4
do_rom_ops() erase
Erasing at 0x120000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 4
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 5
do_rom_ops() erase
Erasing at 0x160000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 5
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 6
do_rom_ops() erase
Erasing at 0x1a0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 6
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 7
do_rom_ops() erase
Erasing at 0x1e0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 7
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 0
do_fip_ops() erase, base 2
Erasing at 0x9e0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 0
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 1
do_fip_ops() erase, base 2
Erasing at 0xbe0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 200000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 2
do_fip_ops() erase, base 2
Erasing at 0xde0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 400000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 3
do_fip_ops() erase, base 2
Erasing at 0xfe0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 600000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
[MSG]Burn complete
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 0
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 1
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 2
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 3
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd fip
new argv[1] fip_read
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_read
arg 2: 0x000000000dec7e50
arg 3: 0
arg 4: 0xbbe00
do_fip_ops() read
sub cmd fip
new argv[1] fip_read
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_read
arg 2: 0x000000000dec7e50
arg 3: 200000
arg 4: 0xbbe00
do_fip_ops() read
[MSG]VERIFY OK
[MSG]Set upgrade_step to 1
Saving Environment to aml-storage...
uboot env amlnf_env_save : ####
aml_nand_save_rsv_info:685, nenv: valid=1, pages=32
release_free_node 112: bitmap=ffffff
release_free_node 125: bitmap=fffff7
aml_nand_save_rsv_info:750,save info to 300000
[MSG]to close image
[MSG]======sdc burn SUCCESS.
gpio: pin GPIOA_16 (gpio 56) value is 1
You might have upgraded it to the wrong firmware?
How did you know it was bricked? Have you tried to access through the browser?
Have you also tried to factory reset the unit by holding the IP report button for 5 seconds?
If you already did that but can't still able to access the miner then you can try SD card flashing You can follow the steps below it requires a Card reader with an OTG plug( if you do not have an OTG card reader you can use the "Micro USB port to USB female connector") and then SD card and PC.
- First, download the s19j-Pro-a113d-amlctrl-flashCard-20211119.zip
- Extract the file to the desktop
- Copy all extracted files and paste them into an SD card(Make sure to format it to FAT32)
- Now plug the OTG Card reader with SD card into the unit then power on
- Leave it for 30 seconds to flash.
Once it's done test the unit again and update here.
How did you know it was bricked? Have you tried to access through the browser?
Have you also tried to factory reset the unit by holding the IP report button for 5 seconds?
If you already did that but can't still able to access the miner then you can try SD card flashing You can follow the steps below it requires a Card reader with an OTG plug( if you do not have an OTG card reader you can use the "Micro USB port to USB female connector") and then SD card and PC.
- First, download the s19j-Pro-a113d-amlctrl-flashCard-20211119.zip
- Extract the file to the desktop
- Copy all extracted files and paste them into an SD card(Make sure to format it to FAT32)
- Now plug the OTG Card reader with SD card into the unit then power on
- Leave it for 30 seconds to flash.
Once it's done test the unit again and update here.
Hello everyone,
I have an amlogic s19 j pro card which I think is totally brick following the firmware update.
I used a TTL cable to analyze the outputs of the board, and here is the log. If anyone has an idea of the fatal error and how to solve it, thank you!
I have an amlogic s19 j pro card which I think is totally brick following the firmware update.
I used a TTL cable to analyze the outputs of the board, and here is the log. If anyone has an idea of the fatal error and how to solve it, thank you!
Code:
AXG:BL1:d1dbf2:a4926f;FEAT:F0DC31BC:2000;POC:F;EMMC:800;NAND:0;READ:0;0.0;0.0;CHK:0;
sdio debug board detected
TE: 136410
BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh
set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 18 00 30 2b 12 45 1d 01 39 25 0b 40 00 00 00 00 00 00 00 00 00 00 00 00 721 - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE: BL31: v1.3(release):3edeb02
NOTICE: BL31: Built : 16:43:54, Apr 14 2020
NOTICE: BL31: AXG secure boot!
NOTICE: BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015884 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12
DRAM: 256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC: aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In: serial
Out: serial
Err: serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
fail in cmd [fatsize usb 0 aml_sdc_burn.ini], rcode 1
ERR(../drivers/usb/gadget/v2_burning/v2_usb_burn/optimus_usb_burn.c)L41:The [aml_sdc_burn.ini] not exist in udisk
Net: sysnopsys gmac3.7
Phy 0 not found
dwmac.ff3f0000amlkey_init() enter!
amlnf_key_read: ####
amlnf_key_read key data len too much
aml_nand_ext_read_rsv_info 520: nkey is invalid! read exit![EFUSE_MSG]keynum is 4
MACADDR:02:97:ad:94:7e:fc(from chipid)
ramdump_init, add:0, size:0
usb_update_flag=
Start read misc partition datas!
[burnup]Rd:Up sz 0x440 to align 0x1000
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
recovery_status=
upgrade_step=2
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
[imgread]szTimeStamp[2021111922403917]
[imgread]secureKernelImgSz=0xc2c000
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
avb2: 0
save_power_post ...
avb2: 0
## Booting Android Image at 0x01080000 ...
reloc_addr =ded86d0
copy done
Kernel command line: init=/sbin/init
[store]Is good fdt check header, no need decrypt!
load dtb from 0x1000000 ......
Amlogic multi-DTB tool
Single DTB detected
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x0203aa00
Loading Ramdisk to 0d83b000, end 0de9d000 ... OK
Loading Device Tree to 000000000d82c000, end 000000000d83a188 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 4224925 us
[ 0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Nov 19 22:32:14 CST 2021
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[ 0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139534 ( 1019 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] can't find symbol:arm_dma_alloc
[ 0.000000@0] can't find symbol:__alloc_from_contiguous
[ 0.000000@0] can't find symbol:cma_allocator_alloc
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0]
[ 0.000000@0] **********************************************************
[ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000@0] ** **
[ 0.000000@0] ** trace_printk() being used. Allocating extra memory. **
[ 0.000000@0] ** **
[ 0.000000@0] ** This means that this is a DEBUG kernel and it is **
[ 0.000000@0] ** unsafe for production use. **
[ 0.000000@0] ** **
[ 0.000000@0] ** If you see this message and you are not debugging **
[ 0.000000@0] ** the kernel, report this immediately to your vendor! **
[ 0.000000@0] ** **
[ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000@0] **********************************************************
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok![ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016907@0] Console: colour dummy device 80x25
[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031586@0] pid_max: default: 32768 minimum: 301
[ 0.036439@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
[ 0.045773@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
[ 0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
[ 0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
[ 0.068603@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
[ 0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
[ 0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
[ 0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
[ 0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
[ 0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
[ 0.106465@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114428@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128873@0] ftrace: allocating 30089 entries in 118 pages
[ 0.184510@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.185326@0] CPU0: update cpu_capacity 1024
[ 0.189652@0] ASID allocator initialised with 32768 entries
[ 0.227632@0] secmon: can't fine clear_range
[ 0.227841@0] EFI services will not be available.
[ 0.231112@0] Meson chip version = RevC (25:C - 23:0)
[ 0.264979@1] Detected VIPT I-cache on CPU1
[ 0.265040@1] CPU1: update cpu_capacity 1024
[ 0.265042@1] CPU1: Booted secondary processor [410fd034]
[ 0.293040@2] Detected VIPT I-cache on CPU2
[ 0.293096@2] CPU2: update cpu_capacity 1024
[ 0.293098@2] CPU2: Booted secondary processor [410fd034]
[ 0.321116@3] Detected VIPT I-cache on CPU3
[ 0.321169@3] CPU3: update cpu_capacity 1024
[ 0.321171@3] CPU3: Booted secondary processor [410fd034]
[ 0.321262@0] Brought up 4 CPUs
[ 0.360482@0] SMP: Total of 4 processors activated.
[ 0.365390@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.371427@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.381994@0] CPU: All CPU(s) started at EL2
[ 0.383167@0] alternatives: patching kernel code
[ 0.388493@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.395698@0] devtmpfs: initialized
[ 0.411161@0] DMI not present or invalid.
[ 0.411522@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.419546@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.426106@0] pinctrl core: initialized pinctrl subsystem
[ 0.432534@0] NET: Registered protocol family 16
[ 0.452056@0] cpuidle: using governor menu
[ 0.452549@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.458169@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.465578@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.471744@0] clkmsr: clkmsr: driver init
[ 0.475764@0] aml_watch_point_probe, in, wp:2
[ 0.480363@0] pstore: using zlib compression
[ 0.484708@0] console [pstore-1] enabled
[ 0.488041@0] pstore: Registered ramoops as persistent store backend
[ 0.494454@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
domain-0 init dvfs: 3
[ 0.508799@0] aml_iomap: amlogic iomap probe done
[ 0.515765@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.517701@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.618064@0] usbcore: registered new interface driver usbfs
[ 0.618239@0] usbcore: registered new interface driver hub
[ 0.623852@0] usbcore: registered new device driver usb
[ 0.629140@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.634088@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.643474@0] PTP clock support registered
[ 0.647834@0] dmi: Firmware registration failed.
[ 0.656640@0] secmon: reserve_mem_size:0x300000
[ 0.656784@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.663792@0] secmon: get page:ffffffbf00140000, 5000
[ 0.668466@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.676827@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.684735@0] NetLabel: Initializing
[ 0.686877@0] NetLabel: domain hash size = 128
[ 0.691464@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.696718@0] NetLabel: unlabeled traffic allowed by default
[ 0.703305@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.832758@0] VFS: Disk quotas dquot_6.6.0
[ 0.832906@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.859843@1] NET: Registered protocol family 2
[ 0.860944@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.866103@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.872770@1] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.879355@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.885304@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.892046@1] NET: Registered protocol family 1
[ 0.897021@1] RPC: Registered named UNIX socket transport module.
[ 0.902435@1] RPC: Registered udp transport module.
[ 0.907326@1] RPC: Registered tcp transport module.
[ 0.912214@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.921441@1] Unpacking initramfs...
[ 1.421674@3] Initramfs unpacking failed: junk in compressed archive
[ 1.428528@3] Freeing initrd memory: 6536K
[ 1.429403@3] hw perfevents: clusterb_enabled = 0
[ 1.431780@3] hw perfevents: cpumasks 0xf, 0x0
[ 1.436248@3] hw perfevents: cluster A irq = 7
[ 1.440814@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.450979@3] audit: initializing netlink subsys (disabled)
[ 1.454377@3] audit: type=2000 audit(1.268:1): initialized
[ 1.461681@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.486533@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.489593@3] NFS: Registering the id_resolver key type
[ 1.492263@3] Key type id_resolver registered
[ 1.496569@3] Key type id_legacy registered
[ 1.501204@3] fuse init (API version 7.26)
[ 1.513161@3] NET: Registered protocol family 38
[ 1.513219@3] Key type asymmetric registered
[ 1.516465@3] Asymmetric key parser 'x509' registered
[ 1.521965@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.529162@3] io scheduler noop registered (default)
[ 1.534130@3] io scheduler deadline registered
[ 1.539030@3] io scheduler cfq registered
[ 1.560049@2] random: fast init done
[ 1.560149@2] random: crng init done
[ 1.560622@3] Unable to detect cache hierarchy for CPU 0
[ 1.603337@3] loop: module loaded
[ 1.604937@3] zram: Added device: zram0
[ 1.605359@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.612105@3] libphy: Fixed MDIO Bus: probed
[ 1.616634@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.621088@3] tun: (C) 1999-2004 Max Krasnyansky
[ 1.629293@3] ee eth reset:Addr = ffffff80081fd008
[ 1.636806@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.638730@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.644011@3] Ring mode enabled
[ 1.647210@3] DMA HW capability register supported[ 1.651953@3] Normal descriptors
[ 1.655259@3] RX Checksum Offload Engine supported
[ 1.660184@3] COE Type 2
[ 1.662783@3] TX Checksum insertion supported
[ 1.667262@3] Wake-Up On Lan supported
[ 1.671215@3] Enable RX Mitigation via HW Watchdog Timer
[ 1.679356@3] libphy: stmmac: probed
[ 1.680114@3] eth%d: No PHY found
sdio debug board detected
TE: 136410
BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh
set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 18 00 30 2b 12 45 1d 01 39 25 0b 40 00 00 00 00 00 00 00 00 00 00 00 00 721 - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE: BL31: v1.3(release):3edeb02
NOTICE: BL31: Built : 16:43:54, Apr 14 2020
NOTICE: BL31: AXG secure boot!
NOTICE: BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015884 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12
DRAM: 256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC: aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In: serial
Out: serial
Err: serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
fail in cmd [fatsize usb 0 aml_sdc_burn.ini], rcode 1
ERR(../drivers/usb/gadget/v2_burning/v2_usb_burn/optimus_usb_burn.c)L41:The [aml_sdc_burn.ini] not exist in udisk
Net: sysnopsys gmac3.7
Phy 0 not found
dwmac.ff3f0000amlkey_init() enter!
amlnf_key_read: ####
amlnf_key_read key data len too much
aml_nand_ext_read_rsv_info 520: nkey is invalid! read exit![EFUSE_MSG]keynum is 4
MACADDR:02:97:ad:94:7e:fc(from chipid)
ramdump_init, add:0, size:0
usb_update_flag=
Start read misc partition datas!
[burnup]Rd:Up sz 0x440 to align 0x1000
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
recovery_status=
upgrade_step=2
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
[imgread]szTimeStamp[2021111922403917]
[imgread]secureKernelImgSz=0xc2c000
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
avb2: 0
save_power_post ...
avb2: 0
## Booting Android Image at 0x01080000 ...
reloc_addr =ded86d0
copy done
Kernel command line: init=/sbin/init
[store]Is good fdt check header, no need decrypt!
load dtb from 0x1000000 ......
Amlogic multi-DTB tool
Single DTB detected
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x0203aa00
Loading Ramdisk to 0d83b000, end 0de9d000 ... OK
Loading Device Tree to 000000000d82c000, end 000000000d83a188 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 4224925 us
[ 0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Nov 19 22:32:14 CST 2021
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[ 0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139534 ( 1019 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] can't find symbol:arm_dma_alloc
[ 0.000000@0] can't find symbol:__alloc_from_contiguous
[ 0.000000@0] can't find symbol:cma_allocator_alloc
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0]
[ 0.000000@0] **********************************************************
[ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000@0] ** **
[ 0.000000@0] ** trace_printk() being used. Allocating extra memory. **
[ 0.000000@0] ** **
[ 0.000000@0] ** This means that this is a DEBUG kernel and it is **
[ 0.000000@0] ** unsafe for production use. **
[ 0.000000@0] ** **
[ 0.000000@0] ** If you see this message and you are not debugging **
[ 0.000000@0] ** the kernel, report this immediately to your vendor! **
[ 0.000000@0] ** **
[ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000@0] **********************************************************
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok![ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016907@0] Console: colour dummy device 80x25
[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031586@0] pid_max: default: 32768 minimum: 301
[ 0.036439@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
[ 0.045773@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
[ 0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
[ 0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
[ 0.068603@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
[ 0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
[ 0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
[ 0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
[ 0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
[ 0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
[ 0.106465@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114428@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128873@0] ftrace: allocating 30089 entries in 118 pages
[ 0.184510@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.185326@0] CPU0: update cpu_capacity 1024
[ 0.189652@0] ASID allocator initialised with 32768 entries
[ 0.227632@0] secmon: can't fine clear_range
[ 0.227841@0] EFI services will not be available.
[ 0.231112@0] Meson chip version = RevC (25:C - 23:0)
[ 0.264979@1] Detected VIPT I-cache on CPU1
[ 0.265040@1] CPU1: update cpu_capacity 1024
[ 0.265042@1] CPU1: Booted secondary processor [410fd034]
[ 0.293040@2] Detected VIPT I-cache on CPU2
[ 0.293096@2] CPU2: update cpu_capacity 1024
[ 0.293098@2] CPU2: Booted secondary processor [410fd034]
[ 0.321116@3] Detected VIPT I-cache on CPU3
[ 0.321169@3] CPU3: update cpu_capacity 1024
[ 0.321171@3] CPU3: Booted secondary processor [410fd034]
[ 0.321262@0] Brought up 4 CPUs
[ 0.360482@0] SMP: Total of 4 processors activated.
[ 0.365390@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.371427@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.381994@0] CPU: All CPU(s) started at EL2
[ 0.383167@0] alternatives: patching kernel code
[ 0.388493@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.395698@0] devtmpfs: initialized
[ 0.411161@0] DMI not present or invalid.
[ 0.411522@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.419546@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.426106@0] pinctrl core: initialized pinctrl subsystem
[ 0.432534@0] NET: Registered protocol family 16
[ 0.452056@0] cpuidle: using governor menu
[ 0.452549@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.458169@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.465578@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.471744@0] clkmsr: clkmsr: driver init
[ 0.475764@0] aml_watch_point_probe, in, wp:2
[ 0.480363@0] pstore: using zlib compression
[ 0.484708@0] console [pstore-1] enabled
[ 0.488041@0] pstore: Registered ramoops as persistent store backend
[ 0.494454@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
domain-0 init dvfs: 3
[ 0.508799@0] aml_iomap: amlogic iomap probe done
[ 0.515765@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.517701@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.618064@0] usbcore: registered new interface driver usbfs
[ 0.618239@0] usbcore: registered new interface driver hub
[ 0.623852@0] usbcore: registered new device driver usb
[ 0.629140@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.634088@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.643474@0] PTP clock support registered
[ 0.647834@0] dmi: Firmware registration failed.
[ 0.656640@0] secmon: reserve_mem_size:0x300000
[ 0.656784@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.663792@0] secmon: get page:ffffffbf00140000, 5000
[ 0.668466@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.676827@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.684735@0] NetLabel: Initializing
[ 0.686877@0] NetLabel: domain hash size = 128
[ 0.691464@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.696718@0] NetLabel: unlabeled traffic allowed by default
[ 0.703305@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.832758@0] VFS: Disk quotas dquot_6.6.0
[ 0.832906@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.859843@1] NET: Registered protocol family 2
[ 0.860944@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.866103@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.872770@1] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.879355@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.885304@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.892046@1] NET: Registered protocol family 1
[ 0.897021@1] RPC: Registered named UNIX socket transport module.
[ 0.902435@1] RPC: Registered udp transport module.
[ 0.907326@1] RPC: Registered tcp transport module.
[ 0.912214@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.921441@1] Unpacking initramfs...
[ 1.421674@3] Initramfs unpacking failed: junk in compressed archive
[ 1.428528@3] Freeing initrd memory: 6536K
[ 1.429403@3] hw perfevents: clusterb_enabled = 0
[ 1.431780@3] hw perfevents: cpumasks 0xf, 0x0
[ 1.436248@3] hw perfevents: cluster A irq = 7
[ 1.440814@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.450979@3] audit: initializing netlink subsys (disabled)
[ 1.454377@3] audit: type=2000 audit(1.268:1): initialized
[ 1.461681@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.486533@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.489593@3] NFS: Registering the id_resolver key type
[ 1.492263@3] Key type id_resolver registered
[ 1.496569@3] Key type id_legacy registered
[ 1.501204@3] fuse init (API version 7.26)
[ 1.513161@3] NET: Registered protocol family 38
[ 1.513219@3] Key type asymmetric registered
[ 1.516465@3] Asymmetric key parser 'x509' registered
[ 1.521965@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.529162@3] io scheduler noop registered (default)
[ 1.534130@3] io scheduler deadline registered
[ 1.539030@3] io scheduler cfq registered
[ 1.560049@2] random: fast init done
[ 1.560149@2] random: crng init done
[ 1.560622@3] Unable to detect cache hierarchy for CPU 0
[ 1.603337@3] loop: module loaded
[ 1.604937@3] zram: Added device: zram0
[ 1.605359@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.612105@3] libphy: Fixed MDIO Bus: probed
[ 1.616634@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.621088@3] tun: (C) 1999-2004 Max Krasnyansky
[ 1.629293@3] ee eth reset:Addr = ffffff80081fd008
[ 1.636806@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.638730@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.644011@3] Ring mode enabled
[ 1.647210@3] DMA HW capability register supported[ 1.651953@3] Normal descriptors
[ 1.655259@3] RX Checksum Offload Engine supported
[ 1.660184@3] COE Type 2
[ 1.662783@3] TX Checksum insertion supported
[ 1.667262@3] Wake-Up On Lan supported
[ 1.671215@3] Enable RX Mitigation via HW Watchdog Timer
[ 1.679356@3] libphy: stmmac: probed
[ 1.680114@3] eth%d: No PHY found
Jump to: