S19 Stopped! | Bitcointalksearch.org

baro0k

copper member

Activity: 35

Merit: 5

Quote from: philipma1957 on July 27, 2021, 08:58:12 AM

Quote from: gt_addict on July 27, 2021, 02:43:24 AM

Quote from: mikeywith on July 27, 2021, 02:25:58 AM

Quote from: baro0k on July 24, 2021, 10:19:55 PM

I just replaced this PSU a month ago and I lost one of the secrws that connected it with the hashboards and tried to find a titanium screw in local shops and find nothing, and I took one of the screws from a house machine and it works fine for around a month now. I upload a photo if you didn't get my point.

As long as the screw is tight enough and the connection isn't loose - there shouldn't be a problem, I highly doubt that reason alone is what killed the PSU, what is your input AC voltage?

Also just check the screw its too long as its going through and possibly touching components.

good point.

I must ask does the room run hot?
35C or 90f or higher.
is the gear clocked high speed vs medium speed.
I have s17pros they like medium or low when it is really hot.

Maybe you have it on high in a hot room.

Maybe you have 205 or 208 volts vs 220-240

if volts sag lower it kills psu's

It's a 220v and yes I used long screws long time ago and it's will take less than a minute to change the screws colour because of heat for the AC voltage am living in Kuwait so 220v is the standard and I followed mikey post about his room step by step so I have a cold and hot rooms the temperature in the cold room runs around 24-28C and for the devices setting its all runs on normal no over clocks at all.

The spare parts arrived today I'll replace the power supply and make sure to send the old one for testing.

ok done replacing it with OEM one and replaced one of the fans since I cut the wire, it's work fine I noticed a high pool rejection might be fixed by the next few hours if not I'll rechecking it again.

after 6 hours of working I lost a fan 😪

Code:


===========================================Miner log===========================================
1970-01-01 00:00:09 Miner compile time: Fri Dec 11 11:23:44 CST 2020 type: Antminer S19 Pro
1970-01-01 00:00:10 This is fix-freq version
1970-01-01 00:00:10 Miner compile time: Fri Dec 11 11:23:44 CST 2020 type: Antminer S19 Pro
1970-01-01 00:00:10 commit version: 1821c90 2020-11-16 16:05:37, build by: jenkins 2020-12-11 11:35:43
1970-01-01 00:00:10 opt_multi_version     = 1
1970-01-01 00:00:10 opt_bitmain_ab        = 1
1970-01-01 00:00:10 mid_auto_gen          = 0
1970-01-01 00:00:10 opt_bitmain_work_mode = 0
1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5800000
1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0x7
1970-01-01 00:00:10 Note: front fan is power on!
1970-01-01 00:00:10 Note: rear fan is power on!
1970-01-01 00:00:10 start the http log.
1970-01-01 00:00:10 httpListenThread start ret=0
1970-01-01 00:00:10 start listen on 6060 ...
1970-01-01 00:00:10 load machine NBP1901 conf
1970-01-01 00:00:10 machine : NBP1901 
1970-01-01 00:00:10 chain_num 4, chain_domain_num 38, chain_asic_num 114, domain_asic_num 3
1970-01-01 00:00:16 miner ID : 8114944857104814
1970-01-01 00:00:16 FPGA Version = 0xB031
1970-01-01 00:00:16 HASH_ON_PLUG V9 = 0x7
1970-01-01 00:00:16 ==========================capability start==========================
1970-01-01 00:00:16 board num = 3
1970-01-01 00:00:16 board id = 0, chain num = 1
1970-01-01 00:00:16 	chain id = 0
1970-01-01 00:00:16 board id = 1, chain num = 1
1970-01-01 00:00:16 	chain id = 1
1970-01-01 00:00:16 board id = 2, chain num = 1
1970-01-01 00:00:16 	chain id = 2
1970-01-01 00:00:16 ==========================capability end============================
1970-01-01 00:00:16 chain num = 3
2021-07-27 21:14:53 [chain 0]
2021-07-27 21:14:53 0x0000 11 4A A6 B4 FC 5D 3B 06   BC A2 07 A9 DD CB 76 B3 
2021-07-27 21:14:53 0x0010 8F 7D DB 5F A7 B9 4A BA   0E 54 4C 06 CF 33 C0 73 
2021-07-27 21:14:53 0x0020 BA AD DE 1F E6 4A 29 62   41 E6 44 CE 57 5A 5E 74 
2021-07-27 21:14:53 0x0030 B9 6E 4A 70 D6 A6 2F FE   89 39 B6 C5 DF EF 42 01 
2021-07-27 21:14:53 0x0040 01 EF 91 C7 1A 04 74 D9   CA 8C FF FF FF FF FF FF 
2021-07-27 21:14:53 0x0050 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x0060 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x0070 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x0080 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x0090 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x00A0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x00B0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:53 0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF 5A 
2021-07-27 21:14:53 
2021-07-27 21:14:55 [chain 1]
2021-07-27 21:14:55 0x0000 11 4A 2C D1 DB C7 7C 2B   4A C7 C0 C2 97 66 08 A9 
2021-07-27 21:14:55 0x0010 7C 85 BF 6D ED 5E 10 75   98 25 29 F1 EB FD 37 1E 
2021-07-27 21:14:55 0x0020 F4 2D 64 02 CD A9 AD E0   4E 4D D2 FB C8 09 7F A9 
2021-07-27 21:14:55 0x0030 F1 1A E3 35 20 A0 83 A2   0E 93 BC E7 D7 D7 CD FD 
2021-07-27 21:14:55 0x0040 74 04 DC 92 34 03 AE 7B   B9 9F FF FF FF FF FF FF 
2021-07-27 21:14:55 0x0050 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x0060 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x0070 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x0080 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x0090 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x00A0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x00B0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:55 0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF 5A 
2021-07-27 21:14:55 
2021-07-27 21:14:57 [chain 2]
2021-07-27 21:14:57 0x0000 11 4A 43 7C 58 3C 04 5A   84 7E EC BE 94 F0 BF 99 
2021-07-27 21:14:57 0x0010 4D DF 78 39 E0 9D 60 44   68 AE 9D 16 25 50 85 E4 
2021-07-27 21:14:57 0x0020 4A EF 84 8F EB 42 3A 8E   5F 27 0F 62 86 29 77 C7 
2021-07-27 21:14:57 0x0030 77 08 2A 8F C1 2F 37 10   6F 16 EF 30 D4 3A 52 60 
2021-07-27 21:14:57 0x0040 27 EC 42 54 8F 48 FD 35   8B 4D FF FF FF FF FF FF 
2021-07-27 21:14:57 0x0050 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x0060 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x0070 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x0080 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x0090 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x00A0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x00B0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x00C0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x00D0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x00E0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF FF 
2021-07-27 21:14:57 0x00F0 FF FF FF FF FF FF FF FF   FF FF FF FF FF FF FF 5A 
2021-07-27 21:14:57 
2021-07-27 21:14:57 fan_eft : 0  fan_pwm : 100
2021-07-27 21:14:57 create thread
2021-07-27 21:14:57 fixed working voltage = 1260
2021-07-27 21:14:57 Chain [0] PCB Version: 0x0100
2021-07-27 21:14:57 Chain [0] BOM Version: 0x0100
2021-07-27 21:14:57 Chain [1] PCB Version: 0x0100
2021-07-27 21:14:57 Chain [1] BOM Version: 0x0100
2021-07-27 21:14:57 Chain [2] PCB Version: 0x0100
2021-07-27 21:14:57 Chain [2] BOM Version: 0x0100
2021-07-27 21:15:01 Fan check passed.
2021-07-27 21:15:02 chain[0] PIC jump to app
2021-07-27 21:15:03 Check chain[0] PIC fw version=0x89
2021-07-27 21:15:04 chain[1] PIC jump to app
2021-07-27 21:15:06 Check chain[1] PIC fw version=0x89
2021-07-27 21:15:07 chain[2] PIC jump to app
2021-07-27 21:15:09 Check chain[2] PIC fw version=0x89
2021-07-27 21:15:09 create thread
2021-07-27 21:15:09 max sensor num = 4
2021-07-27 21:15:09 temperature_monitor_thread start...
2021-07-27 21:15:13 power type version: 0x0071
2021-07-27 21:15:13 Enter sleep to make sure power release finish.
2021-07-27 21:15:44 Slept 30 seconds, diff = 4.
2021-07-27 21:15:44 set_voltage_by_steps to 1500.
2021-07-27 21:15:49 start up min temp by 75a = 32
2021-07-27 21:15:49 set UART baud to 115200
2021-07-27 21:15:54 chain avg vol rise to 15.21
2021-07-27 21:15:58 Chain[0]: find 114 asic, times 0
2021-07-27 21:16:05 Chain[1]: find 114 asic, times 0
2021-07-27 21:16:13 Chain[2]: find 114 asic, times 0
2021-07-27 21:16:13 pulse_mode = 1, ccdly_sel = 1, pwth_sel = 1
2021-07-27 21:16:18 min freq in eeprom = 525
2021-07-27 21:16:18 fixed frequency is 525
2021-07-27 21:16:18 Bring up temperature is 31
2021-07-27 21:16:18 set UART baud to 12000000
2021-07-27 21:16:18 set_voltage_by_steps to 1260.
2021-07-27 21:16:25 STATUS_INITED: soc init done!
2021-07-27 21:16:25 create thread
2021-07-27 21:16:25 create thread
2021-07-27 21:16:28 start to init...
2021-07-27 21:16:36 Init done!
2021-07-27 21:16:36 STATUS_OKAY
2021-07-27 21:16:36 start the cached job
2021-07-27 21:16:36 Version num 8
2021-07-27 21:16:36 Mask num 0xe000
2021-07-27 21:16:36 freq = 525, percent = 90, hcn = 12480, timeout = 449
2021-07-27 21:16:36 set_start_time_point total_tv_start_sys=122 total_tv_end_sys=123
2021-07-28 03:10:20 Error, fan lost, only find 3 (< 4)
2021-07-28 03:10:20 fan_id = 0, fan_speed = 4560
2021-07-28 03:10:20 fan_id = 1, fan_speed = 0
2021-07-28 03:10:20 fan_id = 2, fan_speed = 5160
2021-07-28 03:10:20 fan_id = 3, fan_speed = 5160
2021-07-28 03:10:20 Sweep error string = F:1.
2021-07-28 03:10:20 ERROR_FAN_LOST: fan lost
2021-07-28 03:10:20 stop_mining: fan lost
2021-07-28 03:10:20 uninit_temp_info
2021-07-28 03:10:20 do not read temp anymore...
2021-07-28 03:10:20 cancel thread
2021-07-28 03:10:20 cancel thread
2021-07-28 03:10:20 cancel thread
2021-07-28 03:10:20 ****power off hashboard****
2021-07-28 03:10:22 temp monitor thread exit
2021-07-28 03:16:44 chain 0 hash rate 21373.00 low in 15 mins
2021-07-28 03:16:44 chain 1 hash rate 21556.00 low in 15 mins
2021-07-28 03:16:44 chain 2 hash rate 21688.00 low in 15 mins
2021-07-28 03:31:45 chain 0 hash rate 0.00 low in 15 mins
2021-07-28 03:31:45 chain 1 hash rate 0.00 low in 15 mins
2021-07-28 03:31:45 chain 2 hash rate 0.00 low in 15 mins

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: gt_addict on July 27, 2021, 02:43:24 AM

Quote from: mikeywith on July 27, 2021, 02:25:58 AM

Quote from: baro0k on July 24, 2021, 10:19:55 PM

I just replaced this PSU a month ago and I lost one of the secrws that connected it with the hashboards and tried to find a titanium screw in local shops and find nothing, and I took one of the screws from a house machine and it works fine for around a month now. I upload a photo if you didn't get my point.

As long as the screw is tight enough and the connection isn't loose - there shouldn't be a problem, I highly doubt that reason alone is what killed the PSU, what is your input AC voltage?

Also just check the screw its too long as its going through and possibly touching components.

good point.

I must ask does the room run hot?
35C or 90f or higher.
is the gear clocked high speed vs medium speed.
I have s17pros they like medium or low when it is really hot.

Maybe you have it on high in a hot room.

Maybe you have 205 or 208 volts vs 220-240

if volts sag lower it kills psu's

gt_addict

hero member

Activity: 2534

Merit: 623

Quote from: mikeywith on July 27, 2021, 02:25:58 AM

Quote from: baro0k on July 24, 2021, 10:19:55 PM

I just replaced this PSU a month ago and I lost one of the secrws that connected it with the hashboards and tried to find a titanium screw in local shops and find nothing, and I took one of the screws from a house machine and it works fine for around a month now. I upload a photo if you didn't get my point.

As long as the screw is tight enough and the connection isn't loose - there shouldn't be a problem, I highly doubt that reason alone is what killed the PSU, what is your input AC voltage?

Also just check the screw if its too long as its going through its possibly touching components.

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

Quote from: baro0k on July 24, 2021, 10:19:55 PM

I just replaced this PSU a month ago and I lost one of the secrws that connected it with the hashboards and tried to find a titanium screw in local shops and find nothing, and I took one of the screws from a house machine and it works fine for around a month now. I upload a photo if you didn't get my point.

As long as the screw is tight enough and the connection isn't loose - there shouldn't be a problem, I highly doubt that reason alone is what killed the PSU, what is your input AC voltage?

baro0k

copper member

Activity: 35

Merit: 5

Quote from: philipma1957 on July 24, 2021, 10:07:17 PM

Quote from: baro0k on July 24, 2021, 10:03:31 PM

Quote from: philipma1957 on July 24, 2021, 09:53:24 PM

DEAD PSU.

In your case you need a psu.

So order it from Bitmain

https://shop.bitmain.com/product/parts

oh look it is out of stock.

so you now have a 5000 dollar or more brick

and out of stock here
https://miningcave.com/product/antminer-powersupply-apw12-for-s19-s19-pro-t19/

not available here
https://blokforge.com/product-category/power-supplies/

not here
https://minefarmbuy.com/product-category/psu/

found this one on ebay. very pricey
https://www.ebay.com/itm/255028994952?hash=item3b60e9a388:g:1McAAOSwyRVgfYsu

where do you live what country?

Thank God I purchased an extra one 2 weeks ago 😅 in will come today, the problem is one of the screws isn't the original dose it make since its the reason that this power supply dies?

you are not making sense who told you to update the firmware.

and WTF does this mean:

the problem is one of the screws isn't the original dose it make since its the reason that this power supply dies?

What are you using google translate?

I did a search and find a post in bitmain issues section someone post a reply "try to update firmware .." and the thread starter answer was "thanks its working"

That's why I update it before posting so if its work no sense to post in here.

I just replaced this PSU a month ago and I lost one of the secrws that connected it with the hashboards and tried to find a titanium screw in local shops and find nothing, and I took one of the screws from a house machine and it works fine for around a month now. I upload a photo if you didn't get my point.

https://keybase.pub/baro0k/021a6b14-6b9f-4c05-a7bf-0c1947564bd2.jpg

Excuse my weak English cause its not my main language as well.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: baro0k on July 24, 2021, 10:03:31 PM

Quote from: philipma1957 on July 24, 2021, 09:53:24 PM

DEAD PSU.

In your case you need a psu.

So order it from Bitmain

https://shop.bitmain.com/product/parts

oh look it is out of stock.

so you now have a 5000 dollar or more brick

and out of stock here
https://miningcave.com/product/antminer-powersupply-apw12-for-s19-s19-pro-t19/

not available here
https://blokforge.com/product-category/power-supplies/

not here
https://minefarmbuy.com/product-category/psu/

found this one on ebay. very pricey
https://www.ebay.com/itm/255028994952?hash=item3b60e9a388:g:1McAAOSwyRVgfYsu

where do you live what country?

Thank God I purchased an extra one 2 weeks ago 😅 in will come today, the problem is one of the screws isn't the original dose it make since its the reason that this power supply dies?

you are not making sense who told you to update the firmware.

and WTF does this mean:

the problem is one of the screws isn't the original dose it make since its the reason that this power supply dies?

What are you using google translate?

baro0k

copper member

Activity: 35

Merit: 5

Quote from: philipma1957 on July 24, 2021, 09:53:24 PM

DEAD PSU.

In your case you need a psu.

So order it from Bitmain

https://shop.bitmain.com/product/parts

oh look it is out of stock.

so you now have a 5000 dollar or more brick

and out of stock here
https://miningcave.com/product/antminer-powersupply-apw12-for-s19-s19-pro-t19/

not available here
https://blokforge.com/product-category/power-supplies/

not here
https://minefarmbuy.com/product-category/psu/

found this one on ebay. very pricey
https://www.ebay.com/itm/255028994952?hash=item3b60e9a388:g:1McAAOSwyRVgfYsu

where do you live what country?

Thank God I purchased an extra one 2 weeks ago 😅 in will come today, the problem is one of the screws isn't the original dose it make since its the reason that this power supply dies?

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

DEAD PSU.

In your case you need a psu.

So order it from Bitmain

https://shop.bitmain.com/product/parts

oh look it is out of stock.

so you now have a 5000 dollar or more brick

and out of stock here
https://miningcave.com/product/antminer-powersupply-apw12-for-s19-s19-pro-t19/

not available here
https://blokforge.com/product-category/power-supplies/

not here
https://minefarmbuy.com/product-category/psu/

found this one on ebay. very pricey
https://www.ebay.com/itm/255028994952?hash=item3b60e9a388:g:1McAAOSwyRVgfYsu

where do you live what country?

baro0k

copper member

Activity: 35

Merit: 5

all the devices went offline suddenly so I thud it's a problem with the pool then I saw everything is back to normal except one miner I checked the first log and find an answer in the forum that the miner needs to be software updated I update the software and still facing another issue, everything shows normal but the miner isn't hashing.

a photo shows everything is normal

https://keybase.pub/baro0k/7d6d0c68-fef9-45af-8671-ff5f030a8a55.jpg

Code:

2021-07-25 02:04:34 fan_eft : 0  fan_pwm : 100
2021-07-25 02:04:34 create thread
2021-07-25 02:04:34 fixed working voltage = 1260
2021-07-25 02:04:34 Chain [0] PCB Version: 0x0100
2021-07-25 02:04:34 Chain [0] BOM Version: 0x0100
2021-07-25 02:04:34 Chain [1] PCB Version: 0x0100
2021-07-25 02:04:34 Chain [1] BOM Version: 0x0100
2021-07-25 02:04:34 Chain [2] PCB Version: 0x0100
2021-07-25 02:04:34 Chain [2] BOM Version: 0x0100
2021-07-25 02:04:38 Fan check passed.
2021-07-25 02:04:39 chain[0] PIC jump to app
2021-07-25 02:04:41 Check chain[0] PIC fw version=0x89
2021-07-25 02:04:42 chain[1] PIC jump to app
2021-07-25 02:04:43 Check chain[1] PIC fw version=0x89
2021-07-25 02:04:44 chain[2] PIC jump to app
2021-07-25 02:04:46 Check chain[2] PIC fw version=0x89
2021-07-25 02:04:46 create thread
2021-07-25 02:04:46 max sensor num = 4
2021-07-25 02:04:46 temperature_monitor_thread start...
2021-07-25 02:04:50 power type version: 0x0071
2021-07-25 02:04:50 Enter sleep to make sure power release finish.
2021-07-25 02:05:21 Slept 30 seconds, diff = 1.
2021-07-25 02:05:21 set_voltage_by_steps to 1500.
2021-07-25 02:05:27 power voltage can not meet the target
2021-07-25 02:05:29 power voltage can not meet the target
2021-07-25 02:05:31 power voltage can not meet the target
2021-07-25 02:05:31 Sweep error string = V:1.
2021-07-25 02:05:31 ERROR_POWER_LOST: get power type version failed!
2021-07-25 02:05:31 stop_mining: get power type version failed!
2021-07-25 02:05:31 uninit_temp_info
2021-07-25 02:05:31 do not read temp anymore...
2021-07-25 02:05:31 cancel thread
2021-07-25 02:05:31 cancel thread
2021-07-25 02:05:31 ****power off hashboard****
2021-07-25 02:05:34 start to init...
2021-07-25 02:05:34 Version num 8
2021-07-25 02:05:34 Mask num 0xe000
2021-07-25 02:05:34 Note: addrInterval or corenum is not initialized.
2021-07-25 02:05:34 temp monitor thread exit
2021-07-25 02:05:34 ERROR_SOC_INIT: soc init failed!
2021-07-25 02:05:34 stop_mining: soc init failed!
2021-07-25 02:05:34 ****power off hashboard****
2021-07-25 02:05:36 STATUS_OKAY
2021-07-25 02:05:36 set_start_time_point total_tv_start_sys=85 total_tv_end_sys=86

Topic: S19 Stopped! (Read 158 times)