Topic: S19J pro 104th NO HASH (Read 42 times)
My room is around 27 celsius. No heating problem.
Hello,
My S19J Pro 104th stopped hash yesterday.
Rate abnormal
Temp abnormal
Fault light is on.
Im new to mining and would be nice with some support.
Pool: Nicehash
My log here:
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 load chain 1 eeprom data
2023-12-24 18:18:34 load chain 2 eeprom data
2023-12-24 18:18:34 i2c_sim_init start
2023-12-24 18:18:34 init gpio477
2023-12-24 18:18:34 init gpio476
2023-12-24 18:18:34 i2c_sim_init end
2023-12-24 18:18:36 power open power_version = 0x75
2023-12-24 18:18:38 power is not calibrated
2023-12-24 18:18:40 miner type: Antminer S19j Pro
2023-12-24 18:18:40 multimachine mode
2023-12-24 18:18:40 load machine BHB42631 conf
2023-12-24 18:18:40 machine: BHB42631
2023-12-24 18:18:40 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-12-24 18:18:40 abandon mixboard!
2023-12-24 18:18:40 abandon mixboard!
2023-12-24 18:18:40 fan_eft: 1 fan_pwm: 80
2023-12-24 18:18:40 create thread get_nonce_and_register_thread
2023-12-24 18:18:40 fixed working voltage = 1360
2023-12-24 18:18:40 fixed frequency is 525
2023-12-24 18:18:40 Chain
2023-12-24 18:18:40 Chain [1] BOM Version: 0x0010
2023-12-24 18:18:40 Chain [2] PCB Version: 0x0130
2023-12-24 18:18:40 Chain [2] BOM Version: 0x0010
2023-12-24 18:18:40 bad chain ID = 3
2023-12-24 18:18:40 Fan control approved.
2023-12-24 18:18:40 uart_trans addr:0xf70a6000.
2023-12-24 18:18:40 max sensor number = 4
2023-12-24 18:18:40 STATUS_INITED: soc init complete!
2023-12-24 18:18:40 temperature_monitor_thread_start...
2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:40 cannot read image temp for chain 1
2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:40 cannot read image temp for chain 1
2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:41 unable to read image temp for chain 1
2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:41 unable to read image temp for chain 1
2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:42 cannot read image temp for chain 1
2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:42 cannot read image temp for chain 1
2023-12-24 18:18:42 over max temp, pcb temp 26 (max 75), chip temp 26 (max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6
2023-12-24 18:18:42 Sweep error string = J0:6.
2023-12-24 18:18:42 ERROR_TEMP_TOO_HIGH: over max temp
2023-12-24 18:18:42 stop_mining: over max temp
2023-12-24 18:18:42 uninit_temp_info
2023-12-24 18:18:42 no longer reading temp...
2023-12-24 18:18:42 cancel thread
2023-12-24 18:18:42 *power off hashboard*
2023-12-24 18:18:42 starting...
2023-12-24 18:18:42 warning: power is not calibrated.
2023-12-24 18:18:42 Version number 65536
2023-12-24 18:18:42 Mask num 0x1fffe000
2023-12-24 18:18:42 opt_multi_version = 65536, interval timeout = 2945120
2023-12-24 18:18:42 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-12-24 18:18:44 power type version: 0x0075
2023-12-24 18:18:45 disable power watchdog: 0x0000
2023-12-24 18:18:46 temp monitor thread exit
2023-12-24 18:18:46 Initializing power, wait, this may take up to 2 minutes...
My S19J Pro 104th stopped hash yesterday.
Rate abnormal
Temp abnormal
Fault light is on.
Im new to mining and would be nice with some support.
Pool: Nicehash
My log here:
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 load chain 1 eeprom data
2023-12-24 18:18:34 load chain 2 eeprom data
2023-12-24 18:18:34 i2c_sim_init start
2023-12-24 18:18:34 init gpio477
2023-12-24 18:18:34 init gpio476
2023-12-24 18:18:34 i2c_sim_init end
2023-12-24 18:18:36 power open power_version = 0x75
2023-12-24 18:18:38 power is not calibrated
2023-12-24 18:18:40 miner type: Antminer S19j Pro
2023-12-24 18:18:40 multimachine mode
2023-12-24 18:18:40 load machine BHB42631 conf
2023-12-24 18:18:40 machine: BHB42631
2023-12-24 18:18:40 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-12-24 18:18:40 abandon mixboard!
2023-12-24 18:18:40 abandon mixboard!
2023-12-24 18:18:40 fan_eft: 1 fan_pwm: 80
2023-12-24 18:18:40 create thread get_nonce_and_register_thread
2023-12-24 18:18:40 fixed working voltage = 1360
2023-12-24 18:18:40 fixed frequency is 525
2023-12-24 18:18:40 Chain
- PCB Version: 0x0130
- BOM Version: 0x0010
2023-12-24 18:18:40 Chain [1] BOM Version: 0x0010
2023-12-24 18:18:40 Chain [2] PCB Version: 0x0130
2023-12-24 18:18:40 Chain [2] BOM Version: 0x0010
2023-12-24 18:18:40 bad chain ID = 3
2023-12-24 18:18:40 Fan control approved.
2023-12-24 18:18:40 uart_trans addr:0xf70a6000.
2023-12-24 18:18:40 max sensor number = 4
2023-12-24 18:18:40 STATUS_INITED: soc init complete!
2023-12-24 18:18:40 temperature_monitor_thread_start...
2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:40 cannot read image temp for chain 1
2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:40 cannot read image temp for chain 1
2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:41 unable to read image temp for chain 1
2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:41 unable to read image temp for chain 1
2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:42 cannot read image temp for chain 1
2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:42 cannot read image temp for chain 1
2023-12-24 18:18:42 over max temp, pcb temp 26 (max 75), chip temp 26 (max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6
2023-12-24 18:18:42 Sweep error string = J0:6.
2023-12-24 18:18:42 ERROR_TEMP_TOO_HIGH: over max temp
2023-12-24 18:18:42 stop_mining: over max temp
2023-12-24 18:18:42 uninit_temp_info
2023-12-24 18:18:42 no longer reading temp...
2023-12-24 18:18:42 cancel thread
2023-12-24 18:18:42 *power off hashboard*
2023-12-24 18:18:42 starting...
2023-12-24 18:18:42 warning: power is not calibrated.
2023-12-24 18:18:42 Version number 65536
2023-12-24 18:18:42 Mask num 0x1fffe000
2023-12-24 18:18:42 opt_multi_version = 65536, interval timeout = 2945120
2023-12-24 18:18:42 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-12-24 18:18:44 power type version: 0x0075
2023-12-24 18:18:45 disable power watchdog: 0x0000
2023-12-24 18:18:46 temp monitor thread exit
2023-12-24 18:18:46 Initializing power, wait, this may take up to 2 minutes...
Jump to: