I have tried booting it with one board/2 boards and it wont power on. so put all 3 again and now my root password doesn't work, didn't change it last night.
So i realized it happened to me yesterday as well and i reset it and it got a different IP and then i was able to get on the config page.
Now i can not go to configuration page even when its showing green light.
something's very strange.
For now i have assigned it a static IP on router front and it did took it, but root does not work.
SMH
Might have to return this and just buy from antminer directly
Topic: S7 wont hash (Read 186 times)
Unplug all boards and test them one by one. if they all work individually, try two at a time in all the combinations. We can go from there, but there is no point in trying to diagnose it before testing all the boards.
Take a look here for my reasoning, very similar issue: https://bitcointalksearch.org/topic/antminer-s7-hash-board-versions-2599853
Ended up I had a board that was a couple versions older and it was causing any boards plugged in with it to not hash as well.
Take a look here for my reasoning, very similar issue: https://bitcointalksearch.org/topic/antminer-s7-hash-board-versions-2599853
Ended up I had a board that was a couple versions older and it was causing any boards plugged in with it to not hash as well.
Either will work, but as is you're underpowering the S7. Until you get a different psu or input voltage, you could power 2 of the 3 boards and run like that. Just remember to disconnect the I/O ribbon cable from the board you don't power.
Appreciate the response, 
Yes I have been using 110, but its putting out around 120V. should I be using another PSU for 110 or running a new 220, any thought.
Yes I have been using 110, but its putting out around 120V. should I be using another PSU for 110 or running a new 220, any thought.
Are you running your psu on 110? If so that's your problem: the apw3++ only puts out 1200W on 110 input.
fwiw I have been using APW++ as PSU
Apologies for the mess,
However that's what I was trying to share , but for whatever reason I cant attach a document here .
Found an alternative.
https://prnt.sc/hsp9hb
However that's what I was trying to share , but for whatever reason I cant attach a document here .
Found an alternative.
https://prnt.sc/hsp9hb
Try screenshots of the miner page rather than text vomit like that. Also you need to be looking at the kernel log for problems, the status page tells you very little.
so I bought a second had s7 , when I get to miner status , It looks like its not hashing..
Anyone seen this?
Any help is appreciated.
steps so far.
1. upgraded firmware
2. reset S7, which now shows the default config.
room temp is 24/25 degree Celsius.
(Moderator note: This post was edited by frodocooper to use code tags for the log output.)
Anyone seen this?
Any help is appreciated.
steps so far.
1. upgraded firmware
2. reset S7, which now shows the default config.
room temp is 24/25 degree Celsius.
Code:
Miner Status
Summary
Elapsed 25m16s
GH/S(5s) 0.00
GH/S(avg) 0.00
FoundBlocks 0
LocalWork 3,282,593
Utility 0.00
WU 0.00
BestShare 0
Pools
Pool
URL
User
Status
Diff
GetWorks
Priority
Accepted
Diff1#
DiffA#
DiffR#
DiffS#
Rejected
Discarded
Stale
LSDiff
LSTime
0
stratum+tcp://solo.antpool.com:3333
antminer_1
Alive
65.5K
23
0
0
0
0
0
0
0
437
0
0
0
1
stratum+tcp://p2p.antpool.com:3333
antminer
Dead
0
1
0
0
0
0
0
0
0
0
0
0
2
stratum+tcp://stratum.f2pool.com:3333
ant.1
Alive
2.05K
74
2
0
0
0
0
0
0
508
0
0
0
total
97
0
0
0
0
0
0
945
0
HW
2264
0
0
AntMiner
Chain#
ASIC#
Frequency
Temp
ASIC status
1
45
700
24
oooooooo ooooo oooooooo oooooooo oooooooo oooooooo
2
45
700
25
oooooooo ooooo oooooooo oooooooo oooooooo oooooooo
3
45
700
25
oooooooo ooooo oooooooo oooooooo oooooooo oooooooo
Fan#
Fan1
Fan2
Fan3
Fan4
Fan5
Fan6
Speed (r/min)
2,040
0
2,160
0
0
0
(Moderator note: This post was edited by frodocooper to use code tags for the log output.)
Jump to: