Fan sensor might be broken it sometimes gives a wrong RPM speed or faulty result.
If OP has extra s9 he can test the fan by replacing it and monitor the fan speed this is only what I think, but if it's shorted OP must have multi-tester to check the fan terminal or the fan socket. The negative and positive should not be equal reversely.
@OP you can also try to customize the fan speed by enabling secret menu option from antminer s9 you can follow the guide from here Solution for ANTMINER S9 FANS SPEED Up & Down every 20 Seconds.
Then you can reduce the fan speed, but you must monitor the hashboard temp.
Topic: S9 fans rpm very high and is only detecting two hashboard out of the three (Read 287 times)
October 29, 2018, 05:56:14 PM
October 28, 2018, 10:47:09 PM
I think fan speeds of 30600 rpm would indicate that the tachometer has shorted with +V somewhere. Fan speed reading is 1 byte and measured in multiples of 120, thus the max reading of 255 times 120 gives you 30600. Could be the fans or the controller board that is faulty.
October 22, 2018, 03:17:06 PM
Those fan RPMs are not real and are indicative of a possible failure, if there are fan issues your remaining boards wont hash. As far as the board not registering, its probably just bad at this point.
October 21, 2018, 12:58:25 PM
Have you tried to flash it with autofreq-firmware? According to other miners, the missing hashboard shows after they flash it with this firmware.
Source from here https://bitcointalksearch.org/topic/a-quick-fix-for-antminer-s9-missingnot-showing-hash-board-no-skills-needed-d-5034849
So, I suggest you that flashing your miner with "Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz" may solve your issue.
You can find this firmware from here https://service.bitmain.com/support/download?product=Antminer%20S9
Source from here https://bitcointalksearch.org/topic/a-quick-fix-for-antminer-s9-missingnot-showing-hash-board-no-skills-needed-d-5034849
So, I suggest you that flashing your miner with "Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz" may solve your issue.
You can find this firmware from here https://service.bitmain.com/support/download?product=Antminer%20S9
I have had customers where once we flashed the firmware, this issue indeed was resolved. However, there were some cases where the voltage regulators were bad on a board and thus the firmware push did not solve the issue. If the firmware does not fix the problem, If you are still under warranty I suggest shipping this to Bitmain in California.
October 19, 2018, 06:45:43 PM
Have you tried to flash it with autofreq-firmware? According to other miners, the missing hashboard shows after they flash it with this firmware.
Source from here https://bitcointalksearch.org/topic/a-quick-fix-for-antminer-s9-missingnot-showing-hash-board-no-skills-needed-d-5034849
So, I suggest you that flashing your miner with "Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz" may solve your issue.
You can find this firmware from here https://service.bitmain.com/support/download?product=Antminer%20S9
Source from here https://bitcointalksearch.org/topic/a-quick-fix-for-antminer-s9-missingnot-showing-hash-board-no-skills-needed-d-5034849
So, I suggest you that flashing your miner with "Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz" may solve your issue.
You can find this firmware from here https://service.bitmain.com/support/download?product=Antminer%20S9
October 19, 2018, 10:10:14 AM
S9 fans rpm very high and is only detecting two hash board out of the three and when try to connect to pool it doesn't connect?
in the antminer section it only shows two boards number 6 and number 8.
number 6 has a GH/S(RT) = 12,743.9 HW=31 Temp=67
number 8 has a GH/S(RT) = 4,142.93 HW = 10 Temp=71
Fan3 Fan6
fan speed ()r/min) 30600 30600
kernel after reboot
in the antminer section it only shows two boards number 6 and number 8.
number 6 has a GH/S(RT) = 12,743.9 HW=31 Temp=67
number 8 has a GH/S(RT) = 4,142.93 HW = 10 Temp=71
Fan3 Fan6
fan speed ()r/min) 30600 30600
kernel after reboot
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000310] ps7-ttc #0 at df804000, irq=43
[ 0.000621] Console: colour dummy device 80x30
[ 0.000653] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040209] pid_max: default: 32768 minimum: 301
[ 0.040431] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042631] CPU: Testing write buffer coherency: ok
[ 0.042979] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043040] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[ 0.043261] L310 cache controller enabled
[ 0.043280] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121038] CPU1: Booted secondary processor
[ 0.210231] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210366] Brought up 2 CPUs
[ 0.210386] SMP: Total of 2 processors activated.
[ 0.210395] CPU: All CPU(s) started in SVC mode.
[ 0.211063] devtmpfs: initialized
[ 0.213504] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214759] regulator-dummy: no parameters
[ 0.223744] NET: Registered protocol family 16
[ 0.225952] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.228272] cpuidle: using governor ladder
[ 0.228286] cpuidle: using governor menu
[ 0.235850] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.237387] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.237401] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.237524] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.259639] bio: create slab at 0
[ 0.261427] vgaarb: loaded
[ 0.262151] SCSI subsystem initialized
[ 0.263045] usbcore: registered new interface driver usbfs
[ 0.263220] usbcore: registered new interface driver hub
[ 0.263449] usbcore: registered new device driver usb
[ 0.263978] media: Linux media interface: v0.10
[ 0.264137] Linux video capture interface: v2.00
[ 0.264380] pps_core: LinuxPPS API ver. 1 registered
[ 0.264392] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.264517] PTP clock support registered
[ 0.264899] EDAC MC: Ver: 3.0.0
[ 0.265954] Advanced Linux Sound Architecture Driver Initialized.
[ 0.268981] DMA-API: preallocated 4096 debug entries
[ 0.268997] DMA-API: debugging enabled by kernel config
[ 0.269095] Switched to clocksource arm_global_timer
[ 0.290807] NET: Registered protocol family 2
[ 0.291476] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.291533] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.291618] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.291666] TCP: reno registered
[ 0.291683] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.291719] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.291966] NET: Registered protocol family 1
[ 0.292332] RPC: Registered named UNIX socket transport module.
[ 0.292344] RPC: Registered udp transport module.
[ 0.292353] RPC: Registered tcp transport module.
[ 0.292361] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.292374] PCI: CLS 0 bytes, default 64
[ 0.292828] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.294893] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.297070] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.297258] msgmni has been set to 967
[ 0.298057] io scheduler noop registered
[ 0.298071] io scheduler deadline registered
[ 0.298115] io scheduler cfq registered (default)
[ 0.305821] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.305841] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.430892] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.998358] console [ttyPS0] enabled
[ 1.002651] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.010295] [drm] Initialized drm 1.1.0 20060810
[ 1.027450] brd: module loaded
[ 1.036893] loop: module loaded
[ 1.046487] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.052506] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.060641] libphy: XEMACPS mii bus: probed
[ 1.065014] ------------- phy_id = 0x3625e62
[ 1.069803] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.078356] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.085041] ehci-pci: EHCI PCI platform driver
[ 1.092298] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.099149] usbcore: registered new interface driver usb-storage
[ 1.106014] mousedev: PS/2 mouse device common for all mice
[ 1.112247] i2c /dev entries driver
[ 1.119215] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.124708] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.130637] Xilinx Zynq CpuIdle Driver started
[ 1.135487] sdhci: Secure Digital Host Controller Interface driver
[ 1.141607] sdhci: Copyright(c) Pierre Ossman
[ 1.145919] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.152755] mmc0: no vqmmc regulator found
[ 1.156772] mmc0: no vmmc regulator found
[ 1.199120] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.207836] usbcore: registered new interface driver usbhid
[ 1.213358] usbhid: USB HID core driver
[ 1.218078] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.224369] nand: Micron MT29F2G08ABAEAWP
[ 1.228338] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.234294] Bad block table found at page 131008, version 0x01
[ 1.240535] Bad block table found at page 130944, version 0x01
[ 1.246518] nand_read_bbt: bad block at 0x000006a20000
[ 1.251655] 3 ofpart partitions found on MTD device pl353-nand
[ 1.257406] Creating 3 MTD partitions on "pl353-nand":
[ 1.262563] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.270631] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.277952] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.286942] TCP: cubic registered
[ 1.290209] NET: Registered protocol family 17
[ 1.294865] Registering SWP/SWPB emulation handler
[ 1.300808] regulator-dummy: disabling
[ 1.305153] UBI: attaching mtd1 to ubi0
[ 1.828263] UBI: scanning is finished
[ 1.839926] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.846979] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.853775] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.860452] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.867289] UBI: good PEBs: 1151, bad PEBs: 1, corrupted PEBs: 0
[ 1.873300] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.880410] UBI: max/mean erase counter: 36/21, WL threshold: 4096, image sequence number: 1984962504
[ 1.889615] UBI: available PEBs: 0, total reserved PEBs: 1151, PEBs reserved for bad PEB handling: 39
[ 1.898812] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.898818] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.902878] ALSA device list:
[ 1.902882] No soundcards found.
[ 1.919292] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.980152] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.986078] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.995222] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.005097] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.010136] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 56FDF5FA-8D29-4AA7-95D4-1C2E28C7C4E9, small LPT model
[ 2.021692] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.029120] devtmpfs: mounted
[ 2.032227] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.885605] random: dd urandom read with 0 bits of entropy available
[ 3.279115]
[ 3.279115] bcm54xx_config_init
[ 3.889136]
[ 3.889136] bcm54xx_config_init
[ 6.889974] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 6.896066] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 19.592731] In axi fpga driver!
[ 19.595798] request_mem_region OK!
[ 19.599226] AXI fpga dev virtual address is 0xdf9fc000
[ 19.604295] *base_vir_addr = 0x8c510
[ 19.619575] In fpga mem driver!
[ 19.622779] request_mem_region OK!
[ 19.626338] fpga mem virtual address is 0xe2000000
[ 20.389133]
[ 20.389133] bcm54xx_config_init
[ 21.029116]
[ 21.029116] bcm54xx_config_init
[ 24.029973] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 24.035994] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 219.488629] random: nonblocking pool is initialized
Detect 512MB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=650 Chain[5] voltage_pic=108 value=880
Fix freq=650 Chain[6] voltage_pic=108 value=880
Fix freq=650 Chain[7] voltage_pic=108 value=880
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
Chain[J8] has 63 asic
Chain[J6] has no freq in PIC, set default freq=650M
Chain[J6] has no core num in PIC
Chain[J8] has no freq in PIC, set default freq=650M
Chain[J8] has no core num in PIC
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:5 max freq=650
Chain:5 min freq=650
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
max freq = 650
set baud=1
Chain[J6] PIC temp offset=62,-25,0,0,0,0,0,0
Chain[J6] chip[244] use PIC middle temp offset=-25 typeID=55
New offset Chain[5] chip[244] local:29 remote:31 offset:28
Chain[J6] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset=62,-28,0,0,0,0,0,0
Chain[J8] chip[244] use PIC middle temp offset=-28 typeID=55
New offset Chain[7] chip[244] local:29 remote:31 offset:28
Chain[J8] chip[244] get middle temp offset=28 typeID=55
Chain[J6] set working voltage=880 [108]
Chain[J8] set working voltage=880 [108]
setStartTimePoint total_tv_start_sys=82 total_tv_end_sys=83
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=75.2960 Asic[02]=80.7150 Asic[03]=74.8260 Asic[04]=54.8270 Asic[05]=75.2120 Asic[06]=74.1720 Asic[07]=72.3260 Asic[08]=73.5510
Asic[09]=68.4000 Asic[10]=71.7390 Asic[11]=73.4670 Asic[12]=76.1180 Asic[13]=68.7530 Asic[14]=78.3830 Asic[15]=73.9030 Asic[16]=71.2860
Asic[17]=71.2520 Asic[18]=73.6510 Asic[19]=74.8930 Asic[20]=75.1780 Asic[21]=77.4100 Asic[22]=73.1310 Asic[23]=73.4000 Asic[24]=7884.52
Asic[25]=71.0510 Asic[26]=70.1950 Asic[27]=79.5240 Asic[28]=81.4360 Asic[29]=76.7890 Asic[30]=75.9330 Asic[31]=75.4470 Asic[32]=79.1040
Asic[33]=79.6740 Asic[34]=74.2390 Asic[35]=73.0310 Asic[36]=74.1040 Asic[37]=75.5980 Asic[38]=74.2550 Asic[39]=70.0950 Asic[40]=72.9640
Asic[41]=71.1010 Asic[42]=76.7220 Asic[43]=68.7020 Asic[44]=74.2720 Asic[45]=74.0210 Asic[46]=76.2520 Asic[47]=73.4000 Asic[48]=70.7660
Asic[49]=77.0740 Asic[50]=69.9440 Asic[51]=72.9300 Asic[52]=77.8460 Asic[53]=75.7320 Asic[54]=74.1720 Asic[55]=36.5570 Asic[56]=73.6680
Asic[57]=74.6580 Asic[58]=67.9300 Asic[59]=79.1040 Asic[60]=76.5200 Asic[61]=67.7460 Asic[62]=75.2120 Asic[63]=77.2250
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=75.5140 Asic[02]=77.7620 Asic[03]=68.3670 Asic[04]=81.3860 Asic[05]=82.4430 Asic[06]=70.3800 Asic[07]=70.6990 Asic[08]=74.7420
Asic[09]=74.5240 Asic[10]=81.9060 Asic[11]=74.8260 Asic[12]=71.6720 Asic[13]=74.6080 Asic[14]=8.87500 Asic[15]=71.7050 Asic[16]=74.1550
Asic[17]=55.2640 Asic[18]=671.088 Asic[19]=70.5480 Asic[20]=75.5980 Asic[21]=77.4600 Asic[22]=76.2020 Asic[23]=70.6650 Asic[24]=1.19100
Asic[25]=70.2790 Asic[26]=71.4870 Asic[27]=71.8230 Asic[28]=69.9440 Asic[29]=73.2660 Asic[30]=74.1210 Asic[31]=74.0040 Asic[32]=72.2090
Asic[33]=70.5980 Asic[34]=73.1150 Asic[35]=73.4670 Asic[36]=75.1110 Asic[37]=78.0810 Asic[38]=41.3890 Asic[39]=37.4630 Asic[40]=70.2120
Asic[41]=77.0070 Asic[42]=73.8020 Asic[43]=68.2660 Asic[44]=65.4640 Asic[45]=71.2190 Asic[46]=6.89500 Asic[47]=71.9910 Asic[48]=72.1920
Asic[49]=77.6780 Asic[50]=75.8160 Asic[51]=6.61000 Asic[52]=76.2860 Asic[53]=36.6070 Asic[54]=71.7560 Asic[55]=76.0340 Asic[56]=37.3790
Asic[57]=75.9000 Asic[58]=76.6040 Asic[59]=36.3730 Asic[60]=71.7220 Asic[61]=69.9770 Asic[62]=69.6420 Asic[63]=11.4920
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Asic[24]=7884.520000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[18]=671.088000
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=28
Chain[5] Chip[62] local Temp=58
Chain[5] Chip[62] middle Temp=71
Done read temp on Chain[5]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=28
read failed, old value: Chain[7] Chip[62] local Temp=62
Chain[7] Chip[62] middle Temp=75
Done read temp on Chain[7]
set FAN speed according to: temp_highest=75 temp_top1[PWM_T]=75 temp_top1[TEMP_POS_LOCAL]=62 temp_change=0 fix_fan_steps=-8
set normal FAN speed... with fix_fan_steps=-9
FAN PWM: 52
read_temp_func Done!
CRC error counter=1
[ 0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000310] ps7-ttc #0 at df804000, irq=43
[ 0.000621] Console: colour dummy device 80x30
[ 0.000653] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040209] pid_max: default: 32768 minimum: 301
[ 0.040431] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042631] CPU: Testing write buffer coherency: ok
[ 0.042979] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043040] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[ 0.043261] L310 cache controller enabled
[ 0.043280] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121038] CPU1: Booted secondary processor
[ 0.210231] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210366] Brought up 2 CPUs
[ 0.210386] SMP: Total of 2 processors activated.
[ 0.210395] CPU: All CPU(s) started in SVC mode.
[ 0.211063] devtmpfs: initialized
[ 0.213504] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214759] regulator-dummy: no parameters
[ 0.223744] NET: Registered protocol family 16
[ 0.225952] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.228272] cpuidle: using governor ladder
[ 0.228286] cpuidle: using governor menu
[ 0.235850] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.237387] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.237401] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.237524] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.259639] bio: create slab
[ 0.261427] vgaarb: loaded
[ 0.262151] SCSI subsystem initialized
[ 0.263045] usbcore: registered new interface driver usbfs
[ 0.263220] usbcore: registered new interface driver hub
[ 0.263449] usbcore: registered new device driver usb
[ 0.263978] media: Linux media interface: v0.10
[ 0.264137] Linux video capture interface: v2.00
[ 0.264380] pps_core: LinuxPPS API ver. 1 registered
[ 0.264392] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.264517] PTP clock support registered
[ 0.264899] EDAC MC: Ver: 3.0.0
[ 0.265954] Advanced Linux Sound Architecture Driver Initialized.
[ 0.268981] DMA-API: preallocated 4096 debug entries
[ 0.268997] DMA-API: debugging enabled by kernel config
[ 0.269095] Switched to clocksource arm_global_timer
[ 0.290807] NET: Registered protocol family 2
[ 0.291476] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.291533] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.291618] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.291666] TCP: reno registered
[ 0.291683] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.291719] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.291966] NET: Registered protocol family 1
[ 0.292332] RPC: Registered named UNIX socket transport module.
[ 0.292344] RPC: Registered udp transport module.
[ 0.292353] RPC: Registered tcp transport module.
[ 0.292361] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.292374] PCI: CLS 0 bytes, default 64
[ 0.292828] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.294893] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.297070] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.297258] msgmni has been set to 967
[ 0.298057] io scheduler noop registered
[ 0.298071] io scheduler deadline registered
[ 0.298115] io scheduler cfq registered (default)
[ 0.305821] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.305841] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.430892] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.998358] console [ttyPS0] enabled
[ 1.002651] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.010295] [drm] Initialized drm 1.1.0 20060810
[ 1.027450] brd: module loaded
[ 1.036893] loop: module loaded
[ 1.046487] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.052506] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.060641] libphy: XEMACPS mii bus: probed
[ 1.065014] ------------- phy_id = 0x3625e62
[ 1.069803] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.078356] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.085041] ehci-pci: EHCI PCI platform driver
[ 1.092298] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.099149] usbcore: registered new interface driver usb-storage
[ 1.106014] mousedev: PS/2 mouse device common for all mice
[ 1.112247] i2c /dev entries driver
[ 1.119215] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.124708] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.130637] Xilinx Zynq CpuIdle Driver started
[ 1.135487] sdhci: Secure Digital Host Controller Interface driver
[ 1.141607] sdhci: Copyright(c) Pierre Ossman
[ 1.145919] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.152755] mmc0: no vqmmc regulator found
[ 1.156772] mmc0: no vmmc regulator found
[ 1.199120] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.207836] usbcore: registered new interface driver usbhid
[ 1.213358] usbhid: USB HID core driver
[ 1.218078] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.224369] nand: Micron MT29F2G08ABAEAWP
[ 1.228338] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.234294] Bad block table found at page 131008, version 0x01
[ 1.240535] Bad block table found at page 130944, version 0x01
[ 1.246518] nand_read_bbt: bad block at 0x000006a20000
[ 1.251655] 3 ofpart partitions found on MTD device pl353-nand
[ 1.257406] Creating 3 MTD partitions on "pl353-nand":
[ 1.262563] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.270631] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.277952] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.286942] TCP: cubic registered
[ 1.290209] NET: Registered protocol family 17
[ 1.294865] Registering SWP/SWPB emulation handler
[ 1.300808] regulator-dummy: disabling
[ 1.305153] UBI: attaching mtd1 to ubi0
[ 1.828263] UBI: scanning is finished
[ 1.839926] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.846979] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.853775] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.860452] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.867289] UBI: good PEBs: 1151, bad PEBs: 1, corrupted PEBs: 0
[ 1.873300] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.880410] UBI: max/mean erase counter: 36/21, WL threshold: 4096, image sequence number: 1984962504
[ 1.889615] UBI: available PEBs: 0, total reserved PEBs: 1151, PEBs reserved for bad PEB handling: 39
[ 1.898812] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.898818] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.902878] ALSA device list:
[ 1.902882] No soundcards found.
[ 1.919292] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.980152] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.986078] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.995222] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.005097] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.010136] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 56FDF5FA-8D29-4AA7-95D4-1C2E28C7C4E9, small LPT model
[ 2.021692] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.029120] devtmpfs: mounted
[ 2.032227] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.885605] random: dd urandom read with 0 bits of entropy available
[ 3.279115]
[ 3.279115] bcm54xx_config_init
[ 3.889136]
[ 3.889136] bcm54xx_config_init
[ 6.889974] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 6.896066] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 19.592731] In axi fpga driver!
[ 19.595798] request_mem_region OK!
[ 19.599226] AXI fpga dev virtual address is 0xdf9fc000
[ 19.604295] *base_vir_addr = 0x8c510
[ 19.619575] In fpga mem driver!
[ 19.622779] request_mem_region OK!
[ 19.626338] fpga mem virtual address is 0xe2000000
[ 20.389133]
[ 20.389133] bcm54xx_config_init
[ 21.029116]
[ 21.029116] bcm54xx_config_init
[ 24.029973] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 24.035994] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 219.488629] random: nonblocking pool is initialized
Detect 512MB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=650 Chain[5] voltage_pic=108 value=880
Fix freq=650 Chain[6] voltage_pic=108 value=880
Fix freq=650 Chain[7] voltage_pic=108 value=880
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
Chain[J8] has 63 asic
Chain[J6] has no freq in PIC, set default freq=650M
Chain[J6] has no core num in PIC
Chain[J8] has no freq in PIC, set default freq=650M
Chain[J8] has no core num in PIC
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:5 max freq=650
Chain:5 min freq=650
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
max freq = 650
set baud=1
Chain[J6] PIC temp offset=62,-25,0,0,0,0,0,0
Chain[J6] chip[244] use PIC middle temp offset=-25 typeID=55
New offset Chain[5] chip[244] local:29 remote:31 offset:28
Chain[J6] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset=62,-28,0,0,0,0,0,0
Chain[J8] chip[244] use PIC middle temp offset=-28 typeID=55
New offset Chain[7] chip[244] local:29 remote:31 offset:28
Chain[J8] chip[244] get middle temp offset=28 typeID=55
Chain[J6] set working voltage=880 [108]
Chain[J8] set working voltage=880 [108]
setStartTimePoint total_tv_start_sys=82 total_tv_end_sys=83
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=75.2960 Asic[02]=80.7150 Asic[03]=74.8260 Asic[04]=54.8270 Asic[05]=75.2120 Asic[06]=74.1720 Asic[07]=72.3260 Asic[08]=73.5510
Asic[09]=68.4000 Asic[10]=71.7390 Asic[11]=73.4670 Asic[12]=76.1180 Asic[13]=68.7530 Asic[14]=78.3830 Asic[15]=73.9030 Asic[16]=71.2860
Asic[17]=71.2520 Asic[18]=73.6510 Asic[19]=74.8930 Asic[20]=75.1780 Asic[21]=77.4100 Asic[22]=73.1310 Asic[23]=73.4000 Asic[24]=7884.52
Asic[25]=71.0510 Asic[26]=70.1950 Asic[27]=79.5240 Asic[28]=81.4360 Asic[29]=76.7890 Asic[30]=75.9330 Asic[31]=75.4470 Asic[32]=79.1040
Asic[33]=79.6740 Asic[34]=74.2390 Asic[35]=73.0310 Asic[36]=74.1040 Asic[37]=75.5980 Asic[38]=74.2550 Asic[39]=70.0950 Asic[40]=72.9640
Asic[41]=71.1010 Asic[42]=76.7220 Asic[43]=68.7020 Asic[44]=74.2720 Asic[45]=74.0210 Asic[46]=76.2520 Asic[47]=73.4000 Asic[48]=70.7660
Asic[49]=77.0740 Asic[50]=69.9440 Asic[51]=72.9300 Asic[52]=77.8460 Asic[53]=75.7320 Asic[54]=74.1720 Asic[55]=36.5570 Asic[56]=73.6680
Asic[57]=74.6580 Asic[58]=67.9300 Asic[59]=79.1040 Asic[60]=76.5200 Asic[61]=67.7460 Asic[62]=75.2120 Asic[63]=77.2250
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=75.5140 Asic[02]=77.7620 Asic[03]=68.3670 Asic[04]=81.3860 Asic[05]=82.4430 Asic[06]=70.3800 Asic[07]=70.6990 Asic[08]=74.7420
Asic[09]=74.5240 Asic[10]=81.9060 Asic[11]=74.8260 Asic[12]=71.6720 Asic[13]=74.6080 Asic[14]=8.87500 Asic[15]=71.7050 Asic[16]=74.1550
Asic[17]=55.2640 Asic[18]=671.088 Asic[19]=70.5480 Asic[20]=75.5980 Asic[21]=77.4600 Asic[22]=76.2020 Asic[23]=70.6650 Asic[24]=1.19100
Asic[25]=70.2790 Asic[26]=71.4870 Asic[27]=71.8230 Asic[28]=69.9440 Asic[29]=73.2660 Asic[30]=74.1210 Asic[31]=74.0040 Asic[32]=72.2090
Asic[33]=70.5980 Asic[34]=73.1150 Asic[35]=73.4670 Asic[36]=75.1110 Asic[37]=78.0810 Asic[38]=41.3890 Asic[39]=37.4630 Asic[40]=70.2120
Asic[41]=77.0070 Asic[42]=73.8020 Asic[43]=68.2660 Asic[44]=65.4640 Asic[45]=71.2190 Asic[46]=6.89500 Asic[47]=71.9910 Asic[48]=72.1920
Asic[49]=77.6780 Asic[50]=75.8160 Asic[51]=6.61000 Asic[52]=76.2860 Asic[53]=36.6070 Asic[54]=71.7560 Asic[55]=76.0340 Asic[56]=37.3790
Asic[57]=75.9000 Asic[58]=76.6040 Asic[59]=36.3730 Asic[60]=71.7220 Asic[61]=69.9770 Asic[62]=69.6420 Asic[63]=11.4920
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Asic[24]=7884.520000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[18]=671.088000
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=28
Chain[5] Chip[62] local Temp=58
Chain[5] Chip[62] middle Temp=71
Done read temp on Chain[5]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=28
read failed, old value: Chain[7] Chip[62] local Temp=62
Chain[7] Chip[62] middle Temp=75
Done read temp on Chain[7]
set FAN speed according to: temp_highest=75 temp_top1[PWM_T]=75 temp_top1[TEMP_POS_LOCAL]=62 temp_change=0 fix_fan_steps=-8
set normal FAN speed... with fix_fan_steps=-9
FAN PWM: 52
read_temp_func Done!
CRC error counter=1
Jump to: