S9 HELP! PSU Burnout - Now acting funny

MinerMEDIC

member

Activity: 166

Merit: 82

EET/NASA intern 2013 Bitmain/MicroBT/IPC cert

Fan 5 is decidedly bad, because it's a closed system without any added power the tach should read almost identical to fan 2. If it were closer to zero the system would error out and not begin hashing.

Then there's the bad asics on 7 & 8. CORE=1 asics are basically heaters. But they haven't totally screwed the pooch because they are still passing clock and data up and down the chain.

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Lastly

Since you have a lot of s9s

Pull two good ones swap them to the weird controller.

If problem still there then the controller has a issue.

To confirm this take the fans from the weird controller put to the good controller

If they work you have some kind of controller issue

Hockeybum

member

Activity: 113

Merit: 31

Or remove 1 fan from the end by taking out the 4 screws. If they are both plugged in and attached one will have enough pressure to spin the other, especially if the exhaust fan is dead. See if they are both spinning under their own power.

tim-bc

full member

Activity: 538

Merit: 175

Quote from: PPickles on May 14, 2018, 07:11:27 PM

the fan speed shows as FAN3=1680 , Fan 4=1680 and Fan 6= 4,440.

You might need to replace whichever fan is being detected twice. You can check by booting with one fan plugged in at a time.

https://bitcointalksearch.org/topic/antminer-s9-three-fans-3684164

fanatic26

hero member

Activity: 756

Merit: 560

What do you mean when you apply firmware it doesnt 'hold'?

WHen you fresh flash that auto tune firmware did you give it like 30 minutes to start hashing? They wont hash immediately on fresh firmware.

P.S. The hardware version being blank just means that bminer isnt running, its not a symptom of anything else.

PPickles

newbie

Activity: 3

Merit: 0

Hi, Thanks for taking the time to respond. I really appreciate it.

A) I changed the board, I assumed that the was the first problem.
B) I then tested the hashboards one by one.
C) All the hashboards work.

To recap: The Fan does is not operating correctly and the hashboards are running hotter than normal. Every time I attempt to apply firmware, it does not hold. However, the S9 still operates, at a low fan speed and about 10 degrees hotter than normal.

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: PPickles on May 14, 2018, 08:05:56 PM

No it was not a tokamak. My Question is, how do i apply the correct firmware and get the S9 to behave normally.

you go back and read the rest of my post.

there is a huge chance the psu fried the controller

and you need a new controller

there is a smaller chance the controller could be flashed if it is bad.

the third possibility is the psu damaged 1 board and the board needs repair

that is why I ask you to test the boards 1 by 1.

PPickles

newbie

Activity: 3

Merit: 0

No it was not a tokamak. My Question is, how do i apply the correct firmware and get the S9 to behave normally.

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

I don't get the question did the rosewill die? Was the rosewill a tokamak titanium?

So I ask as I had 3 rosewill tokamak psu's die.

So lets assume the rosewill died and killed off your controller board.

the easy way to test is open the dead miner and pull the 3 boards.

open a good miner and pull the three boards.

Take 1 board from the dead miner and put it in the good miner then see if the known good miner will run the one board.

If it does not run the board the board is damaged

if that board runs take a second board from the dead miner and run it with the good miner.

if that board works then 2 boards are good.

do it up to the three.

if all three run you need a replacement for the controller

myrig some times stocks them.

PPickles

newbie

Activity: 3

Merit: 0

Hi all,

I'd to start by saying I'm happy to pay for service if someone knows how to fix this issue.

I had one of my S9's (13.5 TH) plugged in to 1600W Rosewill PSU. It ran fine for about 4 months. At some point, there was what we are assuming was a power surge. The S9 stopped working.

I did some testing and found that the control board seemed to be the issue. I've gone ahead and replaced the control board. It works now - sort of.

Issues are as follows:

First, when I apply the the AUTO_FREQ fireware update, the hardware version on the system tab is blank and the hashboards do not turn on.

I can get the hash board and the device to turn on when I apply the 650m fixed frequency firmware. However, when I go to the miner config tab and apply the Search Frequency From, it doesn't work. The hashboards turn off after a few seconds and the device resets.

I've updated everything else on the same tab and its mining but the temps are MUCH HIGHER than avg (99,92,95) this is in a room with normal temp (21 degree Celsius) and the fan speed shows as FAN3=1680 , Fan 4=1680 and Fan 6= 4,440.

I have 10 other machines and they dont nearly operate as hot as this ( they are in a room all together with the avg temp at 35 degrees) and the fans only show 2 as operational fan3=6003 and fan6=4,440

I've attached my Kernel Log below. Please ADVISE. Thanks in advance.

Code:

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017

[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine model: Xilinx Zynq

[    0.000000] cma: CMA: reserved 128 MiB at 16800000

[    0.000000] Memory policy: Data cache writealloc

[    0.000000] On node 0 totalpages: 126976

[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000

[    0.000000]   Normal zone: 992 pages used for memmap

[    0.000000]   Normal zone: 0 pages reserved

[    0.000000]   Normal zone: 126976 pages, LIFO batch:31

[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768

[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096

[    0.000000] pcpu-alloc: [0] 0 [0] 1

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984

[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait

[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)

[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)

[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)

[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)

[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)

[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)

[    0.000000] Preemptible hierarchical RCU implementation.

[    0.000000]      Dump stacks of tasks blocking RCU-preempt GP.

[    0.000000]      RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

[    0.000000] NR_IRQS:16 nr_irqs:16 16

[    0.000000] ps7-slcr mapped to df802000

[    0.000000] zynq_clock_init: clkc starts at df802100

[    0.000000] Zynq clock init

[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns

[    0.000310] ps7-ttc #0 at df804000, irq=43

[    0.000619] Console: colour dummy device 80x30

[    0.000651] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)

[    0.040211] pid_max: default: 32768 minimum: 301

[    0.040428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.040447] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.042579] CPU: Testing write buffer coherency: ok

[    0.042920] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[    0.042980] Setting up static identity map for 0x4c4b00 - 0x4c4b58

[    0.043204] L310 cache controller enabled

[    0.043223] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB

[    0.121036] CPU1: Booted secondary processor

[    0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

[    0.210364] Brought up 2 CPUs

[    0.210383] SMP: Total of 2 processors activated.

[    0.210391] CPU: All CPU(s) started in SVC mode.

[    0.211054] devtmpfs: initialized

[    0.213471] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

[    0.214685] regulator-dummy: no parameters

[    0.222362] NET: Registered protocol family 16

[    0.224657] DMA: preallocated 256 KiB pool for atomic coherent allocations

[    0.226946] cpuidle: using governor ladder

[    0.226960] cpuidle: using governor menu

[    0.234399] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered

[    0.235924] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

[    0.235938] hw-breakpoint: maximum watchpoint size is 4 bytes.

[    0.236052] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000

[    0.257859] bio: create slab  at 0

[    0.259270] vgaarb: loaded

[    0.259964] SCSI subsystem initialized

[    0.260977] usbcore: registered new interface driver usbfs

[    0.261179] usbcore: registered new interface driver hub

[    0.261399] usbcore: registered new device driver usb

[    0.261935] media: Linux media interface: v0.10

[    0.262094] Linux video capture interface: v2.00

[    0.262341] pps_core: LinuxPPS API ver. 1 registered

[    0.262353] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 

[    0.262477] PTP clock support registered

[    0.262832] EDAC MC: Ver: 3.0.0

[    0.263908] Advanced Linux Sound Architecture Driver Initialized.

[    0.266757] DMA-API: preallocated 4096 debug entries

[    0.266771] DMA-API: debugging enabled by kernel config

[    0.266844] Switched to clocksource arm_global_timer

[    0.287861] NET: Registered protocol family 2

[    0.288509] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[    0.288566] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[    0.288651] TCP: Hash tables configured (established 4096 bind 4096)

[    0.288695] TCP: reno registered

[    0.288711] UDP hash table entries: 256 (order: 1, 8192 bytes)

[    0.288743] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[    0.288980] NET: Registered protocol family 1

[    0.289330] RPC: Registered named UNIX socket transport module.

[    0.289343] RPC: Registered udp transport module.

[    0.289351] RPC: Registered tcp transport module.

[    0.289359] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.289372] PCI: CLS 0 bytes, default 64

[    0.289808] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

[    0.291833] futex hash table entries: 512 (order: 3, 32768 bytes)

[    0.293933] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

[    0.294118] msgmni has been set to 967

[    0.294899] io scheduler noop registered

[    0.294912] io scheduler deadline registered

[    0.294953] io scheduler cfq registered (default)

[    0.306608] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208

[    0.306627] dma-pl330 f8003000.ps7-dma:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16

[    0.430052] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps

[    0.997681] console [ttyPS0] enabled

[    1.001925] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000

[    1.009556] [drm] Initialized drm 1.1.0 20060810

[    1.026474] brd: module loaded

[    1.035854] loop: module loaded

[    1.045315] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k

[    1.051461] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.

[    1.059408] libphy: XEMACPS mii bus: probed

[    1.063782] ------------- phy_id = 0x3625e62

[    1.068542] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54

[    1.077145] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    1.083768] ehci-pci: EHCI PCI platform driver

[    1.091030] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?

[    1.097894] usbcore: registered new interface driver usb-storage

[    1.104745] mousedev: PS/2 mouse device common for all mice

[    1.110870] i2c /dev entries driver

[    1.117872] zynq-edac f8006000.ps7-ddrc: ecc not enabled

[    1.123351] cpufreq_cpu0: failed to get cpu0 regulator: -19

[    1.129276] Xilinx Zynq CpuIdle Driver started

[    1.134113] sdhci: Secure Digital Host Controller Interface driver

[    1.140319] sdhci: Copyright(c) Pierre Ossman

[    1.144591] sdhci-pltfm: SDHCI platform and OF driver helper

[    1.151416] mmc0: no vqmmc regulator found

[    1.155427] mmc0: no vmmc regulator found

[    1.196868] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA

[    1.205563] usbcore: registered new interface driver usbhid

[    1.211074] usbhid: USB HID core driver

[    1.215790] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda

[    1.222092] nand: Micron MT29F2G08ABAEAWP

[    1.226055] nand: 256MiB, SLC, page size: 2048, OOB size: 64

[    1.231999] Bad block table found at page 131008, version 0x01

[    1.238226] Bad block table found at page 130944, version 0x01

[    1.244274] 3 ofpart partitions found on MTD device pl353-nand

[    1.250056] Creating 3 MTD partitions on "pl353-nand":

[    1.255146] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"

[    1.263180] 0x000002000000-0x00000b000000 : "angstram-rootfs"

[    1.270529] 0x00000b000000-0x000010000000 : "upgrade-rootfs"

[    1.279503] TCP: cubic registered

[    1.282737] NET: Registered protocol family 17

[    1.287446] Registering SWP/SWPB emulation handler

[    1.293327] regulator-dummy: disabling

[    1.297688] UBI: attaching mtd1 to ubi0

[    1.825891] UBI: scanning is finished

[    1.837544] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0

[    1.844601] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[    1.851397] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[    1.858073] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

[    1.864911] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0

[    1.870920] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

[    1.878032] UBI: max/mean erase counter: 16/8, WL threshold: 4096, image sequence number: 1283732989

[    1.887148] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40

[    1.896346] UBI: background thread "ubi_bgt0d" started, PID 1080

[    1.896351] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

[    1.900289] ALSA device list:

[    1.900293]   No soundcards found.

[    1.916728] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082

[    1.945908] UBIFS: recovery needed

[    2.882285] UBIFS: recovery completed

[    2.885964] UBIFS: mounted UBI device 0, volume 0, name "rootfs"

[    2.891914] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[    2.901017] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

[    2.910906] UBIFS: reserved for root: 0 bytes (0 KiB)

[    2.915936] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model

[    2.927256] VFS: Mounted root (ubifs filesystem) on device 0:11.

[    2.934434] devtmpfs: mounted

[    2.937578] Freeing unused kernel memory: 204K (c06d2000 - c0705000)

[    3.797880] random: dd urandom read with 0 bits of entropy available

[    4.186896]

[    4.186896] bcm54xx_config_init

[    4.796891]

[    4.796891] bcm54xx_config_init

[    7.797710] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz

[    7.803805] xemacps e000b000.ps7-ethernet: link up (100/FULL)

[   21.326624] In axi fpga driver!

[   21.329689] request_mem_region OK!

[   21.333080] AXI fpga dev virtual address is 0xdf9fc000

[   21.338219] *base_vir_addr = 0x8c510

[   21.353857] In fpga mem driver!

[   21.356986] request_mem_region OK!

[   21.360491] fpga mem virtual address is 0xe2000000

[   22.156292]

[   22.156292] bcm54xx_config_init

[   22.786220]

[   22.786220] bcm54xx_config_init

[   25.786760] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz

[   25.792781] xemacps e000b000.ps7-ethernet: link up (100/FULL)

[  500.025340] random: nonblocking pool is initialized

This is XILINX board. Totalram:       507527168

Detect 512MB control board of XILINX

DETECT HW version=0008c510

miner ID : 810455825c208814

Miner Type = S9

AsicType = 1387

real AsicNum = 63

use critical mode to search freq...

get PLUG ON=0x000000e0

Find hashboard on Chain[5]

Find hashboard on Chain[6]

Find hashboard on Chain[7]

set_reset_allhashboard = 0x0000ffff

Check chain[5] PIC fw version=0x03

Check chain[6] PIC fw version=0x03

Check chain[7] PIC fw version=0x03

chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

has freq in PIC, will disable freq setting.

chain[5] has freq in PIC and will jump over...

Chain[5] has core num in PIC

Check chain[5] PIC fw version=0x03

chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

has freq in PIC, will disable freq setting.

chain[6] has freq in PIC and will jump over...

Chain[6] has core num in PIC

Chain[6] ASIC[26] has core num=2

Chain[6] ASIC[29] has core num=2

Check chain[6] PIC fw version=0x03

chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

has freq in PIC, will disable freq setting.

chain[7] has freq in PIC and will jump over...

Chain[7] has core num in PIC

Chain[7] ASIC[37] has core num=1

Chain[7] ASIC[40] has core num=1

Chain[7] ASIC[42] has core num=7

Chain[7] ASIC[43] has core num=11

Chain[7] ASIC[61] has core num=1

Check chain[7] PIC fw version=0x03

get PIC voltage=91 on chain[5], value=890

get PIC voltage=125 on chain[6], value=870

get PIC voltage=125 on chain[7], value=870

set_reset_allhashboard = 0x00000000

chain[5] temp offset record: 62,0,0,0,0,0,35,28

chain[5] temp chip I2C addr=0x98

chain[5] has no middle temp, use special fix mode.

chain[6] temp offset record: 62,0,0,0,0,0,35,28

chain[6] temp chip I2C addr=0x98

chain[6] has no middle temp, use special fix mode.

chain[7] temp offset record: 62,0,0,0,0,0,35,28

chain[7] temp chip I2C addr=0x98

chain[7] has no middle temp, use special fix mode.

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

CRC error counter=0

set command mode to VIL

 

--- check asic number

After Get ASIC NUM CRC error counter=0

set_baud=0

The min freq=700

set real timeout 52, need sleep=379392

After TEST CRC error counter=0

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

search freq for 1 times, completed chain = 3, total chain num = 3

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

restart Miner chance num=2

waiting for receive_func to exit!

waiting for pic heart to exit!

bmminer not found= 1376 root       0:00 grep bmminer

 

bmminer not found, restart bmminer ...

bmminer not found=20786 root       0:00 grep bmminer

 

bmminer not found, restart bmminer ...

This is user mode for mining

Detect 512MB control board of XILINX

Miner Type = S9

Miner compile time: Fri Nov 17 17:37:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

set_reset_allhashboard = 0x0000ffff

miner ID : 810455825c208814

set_reset_allhashboard = 0x0000ffff

Checking fans!get fan[2] speed=6000

get fan[2] speed=6000

get fan[2] speed=6000

get fan[2] speed=6000

get fan[2] speed=6000

get fan[2] speed=6000

get fan[5] speed=4560

get fan[2] speed=6000

get fan[5] speed=4560

get fan[2] speed=6000

get fan[5] speed=4560

chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Detect: use voltage limit rules on single board!

Detect: S9_63 use voltage level=1 : 1

Chain[J6] has backup chain_voltage=890

Check chain[5] PIC fw version=0x03

chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Detect: use voltage limit rules on single board!

Detect: S9_63 use voltage level=1 : 1

Chain[J7] has backup chain_voltage=870

Check chain[6] PIC fw version=0x03

chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Detect: use voltage limit rules on single board!

Detect: S9_63 use voltage level=1 : 1

Chain[J8] has backup chain_voltage=870

Check chain[7] PIC fw version=0x03

Chain[J6] orignal chain_voltage_pic=91 value=890

Chain[J7] orignal chain_voltage_pic=125 value=870

Chain[J8] orignal chain_voltage_pic=125 value=870

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

Chain[J6] has 63 asic

Chain[J7] has 63 asic

Chain[J8] has 63 asic

Chain[J6] has core num in PIC

Chain[J7] has core num in PIC

Chain[J7] ASIC[26] has core num=2

Chain[J7] ASIC[29] has core num=2

Chain[J8] has core num in PIC

Chain[J8] ASIC[37] has core num=1

Chain[J8] ASIC[40] has core num=1

Chain[J8] ASIC[42] has core num=7

Chain[J8] ASIC[43] has core num=11

Chain[J8] ASIC[61] has core num=1

miner total rate=13981GH/s fixed rate=13500GH/s

read PIC voltage=940 on chain[5]

Chain:5 chipnum=63

Chain[J6] voltage added=0.0V

Chain:5 temp offset=0

Chain:5 base freq=631

Asic[ 0]:631

Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631

Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631

Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631

Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631

Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631

Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631

Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631

Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631

Chain:5 max freq=631

Chain:5 min freq=631

 

read PIC voltage=940 on chain[6]

Chain:6 chipnum=63

Chain[J7] voltage added=0.0V

Chain:6 temp offset=0

Chain:6 base freq=656

Asic[ 0]:656

Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656

Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656

Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656

Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656

Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656

Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656

Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656

Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656

Chain:6 max freq=656

Chain:6 min freq=656

 

read PIC voltage=940 on chain[7]

Chain:7 chipnum=63

Chain[J8] voltage added=0.0V

Chain:7 temp offset=0

Chain:7 base freq=662

Asic[ 0]:662

Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 Asic[ 8]:662

Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 Asic[16]:662

Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 Asic[24]:662

Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 Asic[29]:662 Asic[30]:662 Asic[31]:662 Asic[32]:662

Asic[33]:662 Asic[34]:662 Asic[35]:662 Asic[36]:662 Asic[37]:662 Asic[38]:662 Asic[39]:662 Asic[40]:662

Asic[41]:662 Asic[42]:662 Asic[43]:662 Asic[44]:662 Asic[45]:662 Asic[46]:662 Asic[47]:662 Asic[48]:662

Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662

Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662

Chain:7 max freq=662

Chain:7 min freq=662

 

 

Miner fix freq ...

read PIC voltage=940 on chain[5]

Chain:5 chipnum=63

Chain[J6] voltage added=0.0V

Chain:5 temp offset=0

Chain:5 base freq=631

Asic[ 0]:631

Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631

Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631

Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631

Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631

Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631

Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631

Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631

Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631

Chain:5 max freq=631

Chain:5 min freq=631

 

read PIC voltage=940 on chain[6]

Chain:6 chipnum=63

Chain[J7] voltage added=0.0V

Chain:6 temp offset=0

Chain:6 base freq=656

Asic[ 0]:631

Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631

Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631

Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631

Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:637 Asic[31]:637 Asic[32]:637

Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637

Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637

Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637

Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637

Chain:6 max freq=637

Chain:6 min freq=631

 

read PIC voltage=940 on chain[7]

Chain:7 chipnum=63

Chain[J8] voltage added=0.0V

Chain:7 temp offset=0

Chain:7 base freq=662

Asic[ 0]:631

Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631

Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637

Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637

Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637

Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637

Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637

Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637

Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637

Chain:7 max freq=637

Chain:7 min freq=631

 

max freq = 637

set baud=1

Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28

chain[5] temp chip I2C addr=0x98

chain[5] has no middle temp, use special fix mode.

Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55

New offset Chain[5] chip[244] local:52 remote:55 offset:29

Chain[J6] chip[244] get middle temp offset=29 typeID=55

Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28

chain[6] temp chip I2C addr=0x98

chain[6] has no middle temp, use special fix mode.

Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55

New offset Chain[6] chip[244] local:48 remote:51 offset:29

Chain[J7] chip[244] get middle temp offset=29 typeID=55

Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28

chain[7] temp chip I2C addr=0x98

chain[7] has no middle temp, use special fix mode.

Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55

New offset Chain[7] chip[244] local:46 remote:49 offset:29

Chain[J8] chip[244] get middle temp offset=29 typeID=55

single board rate=4531 voltage limit=890 on chain[5]

get PIC voltage=890 on chain[5], check: must be < 890

single board rate=4551 voltage limit=890 on chain[6]

get PIC voltage=870 on chain[6], check: must be < 890

single board rate=4552 voltage limit=890 on chain[7]

get PIC voltage=870 on chain[7], check: must be < 890

Chain[J6] set working voltage=890 [91]

Chain[J7] set working voltage=870 [125]

Chain[J8] set working voltage=870 [125]

do heat board 8xPatten for 1 times

start send works on chain[5]

start send works on chain[6]

start send works on chain[7]

get send work num :57456 on Chain[5]

get send work num :57456 on Chain[6]

get send work num :57456 on Chain[7]

wait recv nonce on chain[5]

wait recv nonce on chain[6]

wait recv nonce on chain[7]

get nonces on chain[5]

require nonce number:912

require validnonce number:57456

asic[00]=912       asic[01]=912       asic[02]=912       asic[03]=912       asic[04]=912       asic[05]=912       asic[06]=912                asic[07]=912      

asic[08]=912       asic[09]=912       asic[10]=912       asic[11]=912       asic[12]=912       asic[13]=912       asic[14]=912                asic[15]=912      

asic[16]=912       asic[17]=912       asic[18]=912       asic[19]=912       asic[20]=912       asic[21]=912       asic[22]=912                asic[23]=912      

asic[24]=912       asic[25]=912       asic[26]=912       asic[27]=912       asic[28]=912       asic[29]=912       asic[30]=912                asic[31]=912      

asic[32]=912       asic[33]=912       asic[34]=912       asic[35]=912       asic[36]=912       asic[37]=912       asic[38]=912                asic[39]=912      

asic[40]=912       asic[41]=912       asic[42]=912       asic[43]=912       asic[44]=912       asic[45]=912       asic[46]=912                asic[47]=912      

asic[48]=912       asic[49]=912       asic[50]=912       asic[51]=912       asic[52]=912       asic[53]=912       asic[54]=912                asic[55]=912      

asic[56]=912       asic[57]=912       asic[58]=912       asic[59]=912       asic[60]=912       asic[61]=912       asic[62]=912      

 

 

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

 

 

 

freq[00]=631      freq[01]=631      freq[02]=631      freq[03]=631      freq[04]=631      freq[05]=631      freq[06]=631                freq[07]=631     

freq[08]=631      freq[09]=631      freq[10]=631      freq[11]=631      freq[12]=631      freq[13]=631      freq[14]=631                freq[15]=631     

freq[16]=631      freq[17]=631      freq[18]=631      freq[19]=631      freq[20]=631      freq[21]=631      freq[22]=631                freq[23]=631     

freq[24]=631      freq[25]=631      freq[26]=631      freq[27]=631      freq[28]=631      freq[29]=631      freq[30]=631                freq[31]=631     

freq[32]=631      freq[33]=631      freq[34]=631      freq[35]=631      freq[36]=631      freq[37]=631      freq[38]=631                freq[39]=631     

freq[40]=631      freq[41]=631      freq[42]=631      freq[43]=631      freq[44]=631      freq[45]=631      freq[46]=631                freq[47]=631     

freq[48]=631      freq[49]=631      freq[50]=631      freq[51]=631      freq[52]=631      freq[53]=631      freq[54]=631                freq[55]=631     

freq[56]=631      freq[57]=631      freq[58]=631      freq[59]=631      freq[60]=631      freq[61]=631      freq[62]=631     

 

total valid nonce number:57456

total send work number:57456

require valid nonce number:57456

repeated_nonce_num:0

err_nonce_num:25842

last_nonce_num:44022

get nonces on chain[6]

require nonce number:912

require validnonce number:57456

asic[00]=912       asic[01]=912       asic[02]=912       asic[03]=912       asic[04]=912       asic[05]=912       asic[06]=912                asic[07]=912      

asic[08]=912       asic[09]=912       asic[10]=912       asic[11]=912       asic[12]=912       asic[13]=912       asic[14]=912                asic[15]=912      

asic[16]=912       asic[17]=912       asic[18]=912       asic[19]=912       asic[20]=912       asic[21]=912       asic[22]=912                asic[23]=912      

asic[24]=912       asic[25]=912       asic[26]=912       asic[27]=912       asic[28]=912       asic[29]=912       asic[30]=912                asic[31]=912      

asic[32]=912       asic[33]=912       asic[34]=912       asic[35]=912       asic[36]=912       asic[37]=912       asic[38]=912                asic[39]=912      

asic[40]=912       asic[41]=912       asic[42]=912       asic[43]=912       asic[44]=912       asic[45]=912       asic[46]=912                asic[47]=912      

asic[48]=912       asic[49]=912       asic[50]=912       asic[51]=912       asic[52]=912       asic[53]=912       asic[54]=912                asic[55]=912      

asic[56]=912       asic[57]=912       asic[58]=912       asic[59]=912       asic[60]=912       asic[61]=912       asic[62]=912      

 

 

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

 

 

 

freq[00]=631      freq[01]=631      freq[02]=631      freq[03]=631      freq[04]=631      freq[05]=631      freq[06]=631                freq[07]=631     

freq[08]=631      freq[09]=631      freq[10]=631      freq[11]=631      freq[12]=631      freq[13]=631      freq[14]=631                freq[15]=631     

freq[16]=631      freq[17]=631      freq[18]=631      freq[19]=631      freq[20]=631      freq[21]=631      freq[22]=631                freq[23]=631     

freq[24]=631      freq[25]=631      freq[26]=631      freq[27]=631      freq[28]=631      freq[29]=631      freq[30]=637                freq[31]=637     

freq[32]=637      freq[33]=637      freq[34]=637      freq[35]=637      freq[36]=637      freq[37]=637      freq[38]=637                freq[39]=637     

freq[40]=637      freq[41]=637      freq[42]=637      freq[43]=637      freq[44]=637      freq[45]=637      freq[46]=637                freq[47]=637     

freq[48]=637      freq[49]=637      freq[50]=637      freq[51]=637      freq[52]=637      freq[53]=637      freq[54]=637                freq[55]=637     

freq[56]=637      freq[57]=637      freq[58]=637      freq[59]=637      freq[60]=637      freq[61]=637      freq[62]=637     

 

total valid nonce number:57456

total send work number:57456

require valid nonce number:57456

repeated_nonce_num:0

err_nonce_num:25977

last_nonce_num:36891

get nonces on chain[7]

require nonce number:912

require validnonce number:57456

asic[00]=912       asic[01]=912       asic[02]=912       asic[03]=912       asic[04]=912       asic[05]=912       asic[06]=912                asic[07]=912      

asic[08]=912       asic[09]=912       asic[10]=912       asic[11]=912       asic[12]=912       asic[13]=912       asic[14]=912                asic[15]=912      

asic[16]=912       asic[17]=912       asic[18]=912       asic[19]=912       asic[20]=912       asic[21]=912       asic[22]=912                asic[23]=912      

asic[24]=912       asic[25]=912       asic[26]=912       asic[27]=912       asic[28]=912       asic[29]=912       asic[30]=912                asic[31]=912      

asic[32]=912       asic[33]=912       asic[34]=912       asic[35]=912       asic[36]=912       asic[37]=912       asic[38]=912                asic[39]=912      

asic[40]=912       asic[41]=912       asic[42]=912       asic[43]=912       asic[44]=912       asic[45]=912       asic[46]=912                asic[47]=912      

asic[48]=912       asic[49]=912       asic[50]=912       asic[51]=912       asic[52]=912       asic[53]=912       asic[54]=912                asic[55]=912      

asic[56]=912       asic[57]=912       asic[58]=912       asic[59]=912       asic[60]=912       asic[61]=912       asic[62]=912      

 

 

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

 

 

 

freq[00]=631      freq[01]=631      freq[02]=631      freq[03]=631      freq[04]=631      freq[05]=631      freq[06]=631                freq[07]=631     

freq[08]=631      freq[09]=631      freq[10]=631      freq[11]=631      freq[12]=631      freq[13]=637      freq[14]=637                freq[15]=637     

freq[16]=637      freq[17]=637      freq[18]=637      freq[19]=637      freq[20]=637      freq[21]=637      freq[22]=637                freq[23]=637     

freq[24]=637      freq[25]=637      freq[26]=637      freq[27]=637      freq[28]=637      freq[29]=637      freq[30]=637                freq[31]=637     

freq[32]=637      freq[33]=637      freq[34]=637      freq[35]=637      freq[36]=637      freq[37]=637      freq[38]=637                freq[39]=637     

freq[40]=637      freq[41]=637      freq[42]=637      freq[43]=637      freq[44]=637      freq[45]=637      freq[46]=637                freq[47]=637     

freq[48]=637      freq[49]=637      freq[50]=637      freq[51]=637      freq[52]=637      freq[53]=637      freq[54]=637                freq[55]=637     

freq[56]=637      freq[57]=637      freq[58]=637      freq[59]=637      freq[60]=637      freq[61]=637      freq[62]=637     

 

total valid nonce number:57456

total send work number:57456

require valid nonce number:57456

repeated_nonce_num:0

err_nonce_num:26040

last_nonce_num:29777

chain[5]: All chip cores are opened OK!

Test Patten on chain[5]: OK!

chain[6]: All chip cores are opened OK!

Test Patten on chain[6]: OK!

chain[7]: All chip cores are opened OK!

Test Patten on chain[7]: OK!

setStartTimePoint total_tv_start_sys=323 total_tv_end_sys=324

restartNum = 2 , auto-reinit enabled...


do read_temp_func once...

do check_asic_reg 0x08

 

get RT hashrate from Chain[5]: (asic index start from 1-63)

Asic[01]=76.1850 Asic[02]=67.5110 Asic[03]=69.3400 Asic[04]=71.8060 Asic[05]=66.4370 Asic[06]=77.8790 Asic[07]=71.1680 Asic[08]=76.5710

Asic[09]=70.1790 Asic[10]=69.0380 Asic[11]=72.3930 Asic[12]=73.0980 Asic[13]=74.6750 Asic[14]=73.1150 Asic[15]=69.9100 Asic[16]=74.5240

Asic[17]=67.6120 Asic[18]=71.2020 Asic[19]=69.5580 Asic[20]=69.2730 Asic[21]=71.6550 Asic[22]=70.6990 Asic[23]=69.9600 Asic[24]=66.5380

Asic[25]=75.9670 Asic[26]=69.8930 Asic[27]=71.2360 Asic[28]=74.4900 Asic[29]=73.4840 Asic[30]=74.2390 Asic[31]=68.2160 Asic[32]=69.5080

Asic[33]=76.7050 Asic[34]=68.8030 Asic[35]=74.1380 Asic[36]=70.8830 Asic[37]=74.0710 Asic[38]=75.1780 Asic[39]=76.8220 Asic[40]=74.3390

Asic[41]=74.0540 Asic[42]=76.2020 Asic[43]=74.4060 Asic[44]=73.2660 Asic[45]=71.9070 Asic[46]=69.9440 Asic[47]=71.0680 Asic[48]=70.5480

Asic[49]=69.4570 Asic[50]=67.6450 Asic[51]=73.5170 Asic[52]=72.6620 Asic[53]=75.9500 Asic[54]=71.0510 Asic[55]=72.6620 Asic[56]=69.4910

Asic[57]=69.4740 Asic[58]=69.7260 Asic[59]=71.8560 Asic[60]=71.1010 Asic[61]=69.8770 Asic[62]=72.3600 Asic[63]=75.0270

 

get RT hashrate from Chain[6]: (asic index start from 1-63)

Asic[01]=67.2760 Asic[02]=74.4400 Asic[03]=73.0810 Asic[04]=74.5240 Asic[05]=71.5380 Asic[06]=67.3430 Asic[07]=74.8090 Asic[08]=73.0640

Asic[09]=68.7530 Asic[10]=73.3660 Asic[11]=74.0880 Asic[12]=75.7320 Asic[13]=69.2730 Asic[14]=73.7350 Asic[15]=70.0440 Asic[16]=73.4170

Asic[17]=70.2620 Asic[18]=69.3900 Asic[19]=70.7660 Asic[20]=73.4170 Asic[21]=71.1010 Asic[22]=67.1920 Asic[23]=73.5000 Asic[24]=69.5410

Asic[25]=66.7730 Asic[26]=68.4340 Asic[27]=69.7260 Asic[28]=66.1190 Asic[29]=67.7630 Asic[30]=77.6110 Asic[31]=71.7890 Asic[32]=74.7920

Asic[33]=76.4200 Asic[34]=72.3260 Asic[35]=69.9770 Asic[36]=65.9840 Asic[37]=73.5170 Asic[38]=76.0510 Asic[39]=75.0610 Asic[40]=66.0680

Asic[41]=76.4360 Asic[42]=69.9270 Asic[43]=73.6510 Asic[44]=71.5380 Asic[45]=71.4870 Asic[46]=73.8860 Asic[47]=75.4130 Asic[48]=75.5980

Asic[49]=69.9600 Asic[50]=66.9240 Asic[51]=70.1790 Asic[52]=71.2020 Asic[53]=73.0810 Asic[54]=71.2860 Asic[55]=69.9100 Asic[56]=73.0640

Asic[57]=72.5270 Asic[58]=72.7290 Asic[59]=71.3530 Asic[60]=73.8860 Asic[61]=74.7250 Asic[62]=76.1850 Asic[63]=77.4600

 

get RT hashrate from Chain[7]: (asic index start from 1-63)

Asic[01]=73.1150 Asic[02]=72.3930 Asic[03]=71.7720 Asic[04]=67.1080 Asic[05]=67.5950 Asic[06]=72.1080 Asic[07]=75.2960 Asic[08]=71.6720

Asic[09]=68.3670 Asic[10]=74.2550 Asic[11]=79.1040 Asic[12]=75.2960 Asic[13]=74.5740 Asic[14]=71.6550 Asic[15]=72.8970 Asic[16]=72.1080

Asic[17]=72.6280 Asic[18]=67.7290 Asic[19]=69.5080 Asic[20]=75.0440 Asic[21]=70.9170 Asic[22]=73.4330 Asic[23]=78.8860 Asic[24]=70.2960

Asic[25]=75.3460 Asic[26]=68.9870 Asic[27]=78.1310 Asic[28]=68.1990 Asic[29]=74.7760 Asic[30]=71.6050 Asic[31]=74.0210 Asic[32]=69.1050

Asic[33]=75.7820 Asic[34]=79.2720 Asic[35]=63.3000 Asic[36]=74.1550 Asic[37]=77.4260 Asic[38]=71.4200 Asic[39]=71.4200 Asic[40]=74.6250

Asic[41]=73.8190 Asic[42]=68.6520 Asic[43]=76.4870 Asic[44]=73.3830 Asic[45]=68.7360 Asic[46]=69.2220 Asic[47]=68.6690 Asic[48]=71.4700

Asic[49]=76.6710 Asic[50]=72.6110 Asic[51]=74.9430 Asic[52]=73.0810 Asic[53]=74.1210 Asic[54]=75.0100 Asic[55]=74.6410 Asic[56]=74.1210

Asic[57]=75.6980 Asic[58]=72.0580 Asic[59]=75.3630 Asic[60]=74.3900 Asic[61]=70.2790 Asic[62]=77.1080 Asic[63]=68.5510

Check Chain[J6] ASIC RT error: (asic index start from 1-63)

Check Chain[J7] ASIC RT error: (asic index start from 1-63)

Check Chain[J8] ASIC RT error: (asic index start from 1-63)

Done check_asic_reg

do read temp on Chain[5]

Chain[5] Chip[62] TempTypeID=55 middle offset=29

Chain[5] Chip[62] local Temp=73

Chain[5] Chip[62] middle Temp=82

Special fix Chain[5] Chip[62] middle Temp = 88

Done read temp on Chain[5]

do read temp on Chain[6]

Chain[6] Chip[62] TempTypeID=55 middle offset=29

Chain[6] Chip[62] local Temp=70

Chain[6] Chip[62] middle Temp=79

Special fix Chain[6] Chip[62] middle Temp = 85

Done read temp on Chain[6]

do read temp on Chain[7]

Chain[7] Chip[62] TempTypeID=55 middle offset=29

Chain[7] Chip[62] local Temp=68

Chain[7] Chip[62] middle Temp=79

Special fix Chain[7] Chip[62] middle Temp = 83

Done read temp on Chain[7]

set FAN speed according to: temp_highest=73 temp_top1[PWM_T]=73 temp_top1[TEMP_POS_LOCAL]=73 temp_change=-1 fix_fan_steps=0

FAN PWM: 98

read_temp_func Done!

CRC error counter=0

Topic: S9 HELP! PSU Burnout - Now acting funny (Read 181 times)