Topic: S9 ip alma sorunu (Read 249 times)
O zaman güzel oldu bende atasehir deyim sana numara pm atıyorum
Istabuldaysan çarşamba günü Istanbul'da olucam bende fazla psu var istersen getirirsin makinayi deneriz o sekilde anlariz psu dan mi baska bir arızası mi var. Belki kontrol kartı arızalıda olabilir o zamanda pendikte biri var bu cihazların tamirini yapan ona gösterebilirsin.
İstanbuldayım hocam. Ataşehirdeyim. Özelden numaranı atarsan sevinirim. Yahut ben atatım. Daha seri iletişim kurarız. Makinayı ısıtmak için saç kurutma makinası dahi kullandım 
Edit: çıldırmamak elde değil..
Perform reset arıyorum 10dk sonra solo poola bağlanıyor. Antpoolun solo poolu ve kullanıcısyla. Kendiminkini giriyorum nicehash btc ne varsa deniyorum bağlanmıyor bu sefer
Istabuldaysan çarşamba günü Istanbul'da olucam bende fazla psu var istersen getirirsin makinayi deneriz o sekilde anlariz psu dan mi baska bir arızası mi var. Belki kontrol kartı arızalıda olabilir o zamanda pendikte biri var bu cihazların tamirini yapan ona gösterebilirsin.
Çok enteresan..
Uygulamadan reset attım. Antpool default adresler varken soloya bağlandı. Diğerlerini kapalı gösteriyor.
Bilgişerimi değiştireyim dedim bu seferde bağlanmadı ve yine aynı soruna geçti.
Başka havuzlarada bağlanmıyor..
Uygulamadan reset attım. Antpool default adresler varken soloya bağlandı. Diğerlerini kapalı gösteriyor.
Bilgişerimi değiştireyim dedim bu seferde bağlanmadı ve yine aynı soruna geçti.
Başka havuzlarada bağlanmıyor..
havuz 1 e 443 port olan stratum adresi gir.
Havuz ayarlarını yapabiliyosan antpool da 443 port numarası girip baslat. Benim whatsminer m3 lerde port yüzünden buna benzer bi sorun olmustu port numarasını 443 yaptigimda cozulmustu.
Psu sorunu olsa en azından tek kart calisirdi diye düşünüyorum ama belli de olmaz varsa tanidigin birinde S9 onun psu ile denemek te fayda var.
İp sorununu aştımda hocam bmminer not found hala aşamadım. Arayüzde girebiliyorum. Port konusu benimde kafamı kurcalıyordu. Eskiden çalıştığı bir porta sabitledim ama olmamıştı. Gidip tekrar deneyeyim dediğiniz şekliyle.Psu sorunu olsa en azından tek kart calisirdi diye düşünüyorum ama belli de olmaz varsa tanidigin birinde S9 onun psu ile denemek te fayda var.
Pool1 e 443lü olanımı girip başlatayım hocam?
Yoksa modemden port sabitlemek mi?
Maalesef kimsede yok psu
Havuz ayarlarını yapabiliyosan antpool da 443 port numarası girip baslat. Benim whatsminer m3 lerde port yüzünden buna benzer bi sorun olmustu port numarasını 443 yaptigimda cozulmustu.
Psu sorunu olsa en azından tek kart calisirdi diye düşünüyorum ama belli de olmaz varsa tanidigin birinde S9 onun psu ile denemek te fayda var.
Psu sorunu olsa en azından tek kart calisirdi diye düşünüyorum ama belli de olmaz varsa tanidigin birinde S9 onun psu ile denemek te fayda var.
Simdi biraz saçma gelebilir ama makinayi kalorifer radyatoru üstüne koy biraz isinsin sonra başlatıp dene bakalım calisicakmi. Buda olmazsa mecbur baska bir psu denemen lazım ve ethernet kablonuda mutlaka degistir. 1 taneden fazla S9 un varsa diger S9 un kontrol kartını calsimayan makinaya takip öyle deneyebilirsin belki kontrol kartı arizalidir.
Bunlarda cozum olmazsa GitHub da S9 bmminer to cgminer dosyasını indirip flash layabilirsin.
Cihazın garanti kapsamındaysa bu son söylediğimi yapma.
Hocam kabloyuda değiştirdim. Hatta eve indirip daha sıcak ortamda başka kabloylada denedim. Makina 4saat çalışıp ısındığındada denedim. Tek blok çalıştırmayıda denedim ama nafile.Bunlarda cozum olmazsa GitHub da S9 bmminer to cgminer dosyasını indirip flash layabilirsin.
Cihazın garanti kapsamındaysa bu son söylediğimi yapma.
Kontrol kartı deneyemiyorum maalesef. Psudan olsa dediğiniz gibi tek blok çalıştırmazmıydı?
Modemden firewallda kapadım. Bugün yine gidip bambaşka şeyler deneyeceğim mpdemle alakalı. Gerçi aynı modemlede bağlanmıştı bi kere. Aklıma firewall bile geldi
Sevgili compir dediğin dün benimde aklımı kurcalamıştı. Eve götürüp sıcakta beklettim. Fakat sonuç alamadım. Yani 1 saat makinanın ısınmasını bile bekledim. Belli bir sıcaklık altında böyle bir hata vermiş bir kaç kişidede. Ama şans eserimi soğuktan dolayımı bilemiyoruz şimdilik.
Yani saçma değil mantıklı hocam
Yani saçma değil mantıklı hocam
kardeşim gerekli güncellemeleri indir dene bende de oluyordu güncelleme yap en kötü ihtimal fabrika ayarlarına çevir system>upgrade>perform reset
Hiçbiri olmazsa resetle dediğim gibi havuza bağlanmaya çalış makine biraz fanı hızlandırsın denesin. Benim makine o şekilde geçti. Bir havuz bağlatısı gir bağlanmayı dene. Öylede olmassa (Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar) bu güncellemeyi indir yine dene havuza bağlanmayı.
Hiçbiri olmazsa resetle dediğim gibi havuza bağlanmaya çalış makine biraz fanı hızlandırsın denesin. Benim makine o şekilde geçti. Bir havuz bağlatısı gir bağlanmayı dene. Öylede olmassa (Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar) bu güncellemeyi indir yine dene havuza bağlanmayı.
Simdi biraz saçma gelebilir ama makinayi kalorifer radyatoru üstüne koy biraz isinsin sonra başlatıp dene bakalım calisicakmi. Buda olmazsa mecbur baska bir psu denemen lazım ve ethernet kablonuda mutlaka degistir. 1 taneden fazla S9 un varsa diger S9 un kontrol kartını calsimayan makinaya takip öyle deneyebilirsin belki kontrol kartı arizalidir.
Bunlarda cozum olmazsa GitHub da S9 bmminer to cgminer dosyasını indirip flash layabilirsin.
Cihazın garanti kapsamındaysa bu son söylediğimi yapma.
Bunlarda cozum olmazsa GitHub da S9 bmminer to cgminer dosyasını indirip flash layabilirsin.
Cihazın garanti kapsamındaysa bu son söylediğimi yapma.
Bence sorun büyük ihtimalle PSU da çıkacaktır,tabi bir de internetiniz stabil ise bu da önemli. Bitmain APW3++ 12-1600W Psu mu sizinki?
Arkadaşlar bugün s9 um önce bir türlü bağlanmadı. Bir kaç defa reset, ip report falan yaptım. Daha sonra tekrar yer değiştirip son kez denemek istedim çalıştı. Eve getirdim bu sefer aynı sorunu yine yaptı. Ancak şimdi birde ip almıyor. Paneline giremiyorum. Yine biraz dinlenmeye bıraktım kapatıp. Bu sorunla karşılaşan, çözen, çözümünü bilen var mı?
Edit: şimdide yine ip alıyor ancak bağlanmıyor bir türlü
O SORUN BENDEDE OLUYOR RESMENEdit: şimdide yine ip alıyor ancak bağlanmıyor bir türlü
Bence bitmaine destek kısmına bir ticket gönderip detaylı bir yardım istemeniz daha iyi olur fakat geç dönüş yapabiliyorlar.
Onuda attım hocam brklicez mecburen. Güncellemerin hrpsi socket hatası veriyor. Son güncelleme o hatayı vermiyor ancak ondada yine bmminer no found hatası devam ediyor.
Bence bitmaine destek kısmına bir ticket gönderip detaylı bir yardım istemeniz daha iyi olur fakat geç dönüş yapabiliyorlar.
Psu değiştiremedim ama tek blok çalıştırdığımdada bağlanmadı. Bir türlü bmminer versiyonu gelmiyor doğal olarak havuzlarada bağlanamıylrum. Miner status bomboş.. bu bmminer hatası ne menem bişeydir. Kaç kez hard resette attım ipreporttanda reset attım. Arayüzdende attım.
Psu değiştiremiyorum şuan.
Ama şöyle bişey var arkadaşlar ara çalışıp gidiyor. Değişik yani.
Ama şöyle bişey var arkadaşlar ara çalışıp gidiyor. Değişik yani.
Psu degistiremiyosan tek kartla calistir makinayi eger tek kart ile calisirsa yeni psu alman gerekicek. Suan gozuken bmminer not found hatasi.
Kernel Log ta sıkıntı yok,bir de NiceHash deneyin,PSU'yu değiştirdiniz mi?
Kernel log bilgilerini burada paylaşır mısın? ASIC çiplerinde sıkıntı olabilir.
Hocam çok değişik bir durum. Kasım güncellemesini yaptım soket hatası gitti ama miner status falan boştu. 5 saat bununla uğraştım. Sonra bi dediğiniz şekilde ip report yapıp sigara almaya çıktım. Döndüğümde bağlanmıştı. Ama çok tuhaftır(ip report ile bu sefer reset atmış. Worker falan değişmişti.) ama bağlanmıştı s9un default workerlarıyla. Değiştireyim dedim bu sefer yine gitti ve 6 saattir hala gelmedi.Edit antpooldan viabtc ye geçtim ama bişey değişmedi.
Quote
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000307] ps7-ttc #0 at df804000, irq=43
[ 0.000619] Console: colour dummy device 80x30
[ 0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040208] pid_max: default: 32768 minimum: 301
[ 0.040428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040448] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042573] CPU: Testing write buffer coherency: ok
[ 0.042909] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042969] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043195] L310 cache controller enabled
[ 0.043214] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121034] CPU1: Booted secondary processor
[ 0.210228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210360] Brought up 2 CPUs
[ 0.210379] SMP: Total of 2 processors activated.
[ 0.210388] CPU: All CPU(s) started in SVC mode.
[ 0.211048] devtmpfs: initialized
[ 0.213458] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214671] regulator-dummy: no parameters
[ 0.222354] NET: Registered protocol family 16
[ 0.224646] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226939] cpuidle: using governor ladder
[ 0.226953] cpuidle: using governor menu
[ 0.234413] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235937] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235951] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236065] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257885] bio: create slab at 0
[ 0.259308] vgaarb: loaded
[ 0.260007] SCSI subsystem initialized
[ 0.261030] usbcore: registered new interface driver usbfs
[ 0.261215] usbcore: registered new interface driver hub
[ 0.261435] usbcore: registered new device driver usb
[ 0.261966] media: Linux media interface: v0.10
[ 0.262122] Linux video capture interface: v2.00
[ 0.262369] pps_core: LinuxPPS API ver. 1 registered
[ 0.262380] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.262503] PTP clock support registered
[ 0.262860] EDAC MC: Ver: 3.0.0
[ 0.263930] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266776] DMA-API: preallocated 4096 debug entries
[ 0.266790] DMA-API: debugging enabled by kernel config
[ 0.266866] Switched to clocksource arm_global_timer
[ 0.288365] NET: Registered protocol family 2
[ 0.289018] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.289076] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.289161] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.289204] TCP: reno registered
[ 0.289220] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.289252] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.289488] NET: Registered protocol family 1
[ 0.289835] RPC: Registered named UNIX socket transport module.
[ 0.289847] RPC: Registered udp transport module.
[ 0.289856] RPC: Registered tcp transport module.
[ 0.289864] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289876] PCI: CLS 0 bytes, default 64
[ 0.290310] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.292332] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.294436] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.294621] msgmni has been set to 967
[ 0.295400] io scheduler noop registered
[ 0.295413] io scheduler deadline registered
[ 0.295454] io scheduler cfq registered (default)
[ 0.307302] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307322] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.431460] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.999931] console [ttyPS0] enabled
[ 1.004214] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.011881] [drm] Initialized drm 1.1.0 20060810
[ 1.028939] brd: module loaded
[ 1.038304] loop: module loaded
[ 1.048004] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.053756] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.061722] libphy: XEMACPS mii bus: probed
[ 1.066091] ------------- phy_id = 0x3625e62
[ 1.070991] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.079842] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.086468] ehci-pci: EHCI PCI platform driver
[ 1.093724] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.100563] usbcore: registered new interface driver usb-storage
[ 1.107438] mousedev: PS/2 mouse device common for all mice
[ 1.113519] i2c /dev entries driver
[ 1.120464] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.125959] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.131879] Xilinx Zynq CpuIdle Driver started
[ 1.136707] sdhci: Secure Digital Host Controller Interface driver
[ 1.142939] sdhci: Copyright(c) Pierre Ossman
[ 1.147245] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.154015] mmc0: no vqmmc regulator found
[ 1.158052] mmc0: no vmmc regulator found
[ 1.196895] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.207628] usbcore: registered new interface driver usbhid
[ 1.213112] usbhid: USB HID core driver
[ 1.217888] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.224154] nand: Micron MT29F2G08ABAEAWP
[ 1.228225] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.234088] Bad block table found at page 131008, version 0x01
[ 1.240355] Bad block table found at page 130944, version 0x01
[ 1.246411] 3 ofpart partitions found on MTD device pl353-nand
[ 1.252183] Creating 3 MTD partitions on "pl353-nand":
[ 1.257328] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.265343] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.272695] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.281632] TCP: cubic registered
[ 1.284865] NET: Registered protocol family 17
[ 1.289588] Registering SWP/SWPB emulation handler
[ 1.295460] regulator-dummy: disabling
[ 1.299863] UBI: attaching mtd1 to ubi0
[ 1.825998] UBI: scanning is finished
[ 1.837637] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.844689] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.851477] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.858160] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.864999] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.871009] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.878120] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[ 1.887150] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.896349] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.896354] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.900286] ALSA device list:
[ 1.900290] No soundcards found.
[ 1.916721] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.945738] UBIFS: recovery needed
[ 2.025327] UBIFS: recovery completed
[ 2.029042] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.034966] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.044107] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.053986] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.059025] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[ 2.070536] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.077957] devtmpfs: mounted
[ 2.081059] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.925441] random: dd urandom read with 0 bits of entropy available
[ 3.316904]
[ 3.316904] bcm54xx_config_init
[ 3.926912]
[ 3.926912] bcm54xx_config_init
[ 7.927748] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.933839] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 24.403255] In axi fpga driver!
[ 24.406322] request_mem_region OK!
[ 24.409755] AXI fpga dev virtual address is 0xdf9fc000
[ 24.414820] *base_vir_addr = 0x8c510
[ 24.430453] In fpga mem driver!
[ 24.433526] request_mem_region OK!
[ 24.437116] fpga mem virtual address is 0xe2000000
[ 25.226899]
[ 25.226899] bcm54xx_config_init
[ 25.856891]
[ 25.856891] bcm54xx_config_init
[ 29.857737] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 29.863755] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1299.566050] random: nonblocking pool is initialized
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 803825896600881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[0] has core num=1
Chain[5] ASIC[23] has core num=1
Chain[5] ASIC[24] has core num=1
Chain[5] ASIC[25] has core num=1
Chain[5] ASIC[26] has core num=1
Chain[5] ASIC[27] has core num=1
Chain[5] ASIC[28] has core num=1
Chain[5] ASIC[29] has core num=15
Chain[5] ASIC[30] has core num=3
Chain[5] ASIC[31] has core num=1
Chain[5] ASIC[32] has core num=1
Chain[5] ASIC[33] has core num=1
Chain[5] ASIC[34] has core num=1
Chain[5] ASIC[35] has core num=2
Chain[5] ASIC[36] has core num=1
Chain[5] ASIC[37] has core num=2
Chain[5] ASIC[38] has core num=3
Chain[5] ASIC[39] has core num=1
Chain[5] ASIC[41] has core num=2
Chain[5] ASIC[58] has core num=2
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[0] has core num=1
Chain[6] ASIC[1] has core num=1
Chain[6] ASIC[2] has core num=3
Chain[6] ASIC[27] has core num=1
Chain[6] ASIC[29] has core num=2
Chain[6] ASIC[30] has core num=2
Chain[6] ASIC[31] has core num=2
Chain[6] ASIC[57] has core num=2
Chain[6] ASIC[58] has core num=1
Chain[6] ASIC[59] has core num=2
Chain[6] ASIC[60] has core num=1
Chain[6] ASIC[61] has core num=2
Chain[6] ASIC[62] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 4891 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found= 5111 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found=24638 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 803825896600881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[5] speed=5640
get fan[2] speed=4920
get fan[5] speed=5640
get fan[2] speed=4920
get fan[5] speed=5640
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=74 value=900
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
Chain[J7] orignal chain_voltage_pic=74 value=900
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
Chain[J8] orignal chain_voltage_pic=74 value=900
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[0] has core num=1
Chain[J6] ASIC[23] has core num=1
Chain[J6] ASIC[24] has core num=1
Chain[J6] ASIC[25] has core num=1
Chain[J6] ASIC[26] has core num=1
Chain[J6] ASIC[27] has core num=1
Chain[J6] ASIC[28] has core num=1
Chain[J6] ASIC[29] has core num=15
Chain[J6] ASIC[30] has core num=3
Chain[J6] ASIC[31] has core num=1
Chain[J6] ASIC[32] has core num=1
Chain[J6] ASIC[33] has core num=1
Chain[J6] ASIC[34] has core num=1
Chain[J6] ASIC[35] has core num=2
Chain[J6] ASIC[36] has core num=1
Chain[J6] ASIC[37] has core num=2
Chain[J6] ASIC[38] has core num=3
Chain[J6] ASIC[39] has core num=1
Chain[J6] ASIC[41] has core num=2
Chain[J6] ASIC[58] has core num=2
Chain[J7] has core num in PIC
Chain[J7] ASIC[0] has core num=1
Chain[J7] ASIC[1] has core num=1
Chain[J7] ASIC[2] has core num=3
Chain[J7] ASIC[27] has core num=1
Chain[J7] ASIC[29] has core num=2
Chain[J7] ASIC[30] has core num=2
Chain[J7] ASIC[31] has core num=2
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[58] has core num=1
Chain[J7] ASIC[59] has core num=2
Chain[J7] ASIC[60] has core num=1
Chain[J7] ASIC[61] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
miner total rate=14069GH/s fixed rate=14000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:668
Asic[ 1]:668 Asic[ 2]:668 Asic[ 3]:668 Asic[ 4]:668 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Asic[47]:668 Asic[48]:668
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668
Chain:5 max freq=668
Chain:5 min freq=668
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=656
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=656
Chain:6 min freq=656
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:668
Asic[ 1]:668 Asic[ 2]:668 Asic[ 3]:668 Asic[ 4]:668 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Detect a bad chip=29 on chain[5], fixed to 400M
Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Asic[47]:668 Asic[48]:668
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668
Chain:5 max freq=668
Chain:5 min freq=668
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=656
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=656
Chain:6 min freq=656
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
max freq = 668
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:33 remote:36 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:29 remote:31 offset:28
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:28 remote:31 offset:27
Chain[J8] chip[244] get middle temp offset=27 typeID=55
single board rate=4703 voltage limit=870 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 870
single board rate=4697 voltage limit=870 on chain[6]
get PIC voltage=870 on chain[6], check: must be < 870
single board rate=4668 voltage limit=870 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 870
Chain[J6] set working voltage=870 [125]
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
Chain[5] Chip[62] local Temp=36
Chain[5] Chip[62] middle Temp=48
Special fix Chain[5] Chip[62] middle Temp = 51
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=28
Chain[6] Chip[62] local Temp=33
Chain[6] Chip[62] middle Temp=47
Special fix Chain[6] Chip[62] middle Temp = 48
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=27
Chain[7] Chip[62] local Temp=34
Chain[7] Chip[62] middle Temp=46
Special fix Chain[7] Chip[62] middle Temp = 49
Done read temp on Chain[7]
set FAN speed according to: temp_highest=36 temp_top1[PWM_T]=36 temp_top1[TEMP_POS_LOCAL]=36 temp_change=2 fix_fan_steps=0
set normal FAN speed...
FAN PWM: 22
read_temp_func Done!
CRC error counter=0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc:
- 0
- 1
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000307] ps7-ttc #0 at df804000, irq=43
[ 0.000619] Console: colour dummy device 80x30
[ 0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040208] pid_max: default: 32768 minimum: 301
[ 0.040428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040448] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042573] CPU: Testing write buffer coherency: ok
[ 0.042909] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042969] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043195] L310 cache controller enabled
[ 0.043214] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121034] CPU1: Booted secondary processor
[ 0.210228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210360] Brought up 2 CPUs
[ 0.210379] SMP: Total of 2 processors activated.
[ 0.210388] CPU: All CPU(s) started in SVC mode.
[ 0.211048] devtmpfs: initialized
[ 0.213458] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214671] regulator-dummy: no parameters
[ 0.222354] NET: Registered protocol family 16
[ 0.224646] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226939] cpuidle: using governor ladder
[ 0.226953] cpuidle: using governor menu
[ 0.234413] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235937] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235951] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236065] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257885] bio: create slab
[ 0.259308] vgaarb: loaded
[ 0.260007] SCSI subsystem initialized
[ 0.261030] usbcore: registered new interface driver usbfs
[ 0.261215] usbcore: registered new interface driver hub
[ 0.261435] usbcore: registered new device driver usb
[ 0.261966] media: Linux media interface: v0.10
[ 0.262122] Linux video capture interface: v2.00
[ 0.262369] pps_core: LinuxPPS API ver. 1 registered
[ 0.262380] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.262503] PTP clock support registered
[ 0.262860] EDAC MC: Ver: 3.0.0
[ 0.263930] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266776] DMA-API: preallocated 4096 debug entries
[ 0.266790] DMA-API: debugging enabled by kernel config
[ 0.266866] Switched to clocksource arm_global_timer
[ 0.288365] NET: Registered protocol family 2
[ 0.289018] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.289076] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.289161] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.289204] TCP: reno registered
[ 0.289220] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.289252] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.289488] NET: Registered protocol family 1
[ 0.289835] RPC: Registered named UNIX socket transport module.
[ 0.289847] RPC: Registered udp transport module.
[ 0.289856] RPC: Registered tcp transport module.
[ 0.289864] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289876] PCI: CLS 0 bytes, default 64
[ 0.290310] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.292332] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.294436] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.294621] msgmni has been set to 967
[ 0.295400] io scheduler noop registered
[ 0.295413] io scheduler deadline registered
[ 0.295454] io scheduler cfq registered (default)
[ 0.307302] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307322] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.431460] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.999931] console [ttyPS0] enabled
[ 1.004214] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.011881] [drm] Initialized drm 1.1.0 20060810
[ 1.028939] brd: module loaded
[ 1.038304] loop: module loaded
[ 1.048004] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.053756] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.061722] libphy: XEMACPS mii bus: probed
[ 1.066091] ------------- phy_id = 0x3625e62
[ 1.070991] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.079842] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.086468] ehci-pci: EHCI PCI platform driver
[ 1.093724] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.100563] usbcore: registered new interface driver usb-storage
[ 1.107438] mousedev: PS/2 mouse device common for all mice
[ 1.113519] i2c /dev entries driver
[ 1.120464] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.125959] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.131879] Xilinx Zynq CpuIdle Driver started
[ 1.136707] sdhci: Secure Digital Host Controller Interface driver
[ 1.142939] sdhci: Copyright(c) Pierre Ossman
[ 1.147245] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.154015] mmc0: no vqmmc regulator found
[ 1.158052] mmc0: no vmmc regulator found
[ 1.196895] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.207628] usbcore: registered new interface driver usbhid
[ 1.213112] usbhid: USB HID core driver
[ 1.217888] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.224154] nand: Micron MT29F2G08ABAEAWP
[ 1.228225] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.234088] Bad block table found at page 131008, version 0x01
[ 1.240355] Bad block table found at page 130944, version 0x01
[ 1.246411] 3 ofpart partitions found on MTD device pl353-nand
[ 1.252183] Creating 3 MTD partitions on "pl353-nand":
[ 1.257328] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.265343] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.272695] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.281632] TCP: cubic registered
[ 1.284865] NET: Registered protocol family 17
[ 1.289588] Registering SWP/SWPB emulation handler
[ 1.295460] regulator-dummy: disabling
[ 1.299863] UBI: attaching mtd1 to ubi0
[ 1.825998] UBI: scanning is finished
[ 1.837637] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.844689] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.851477] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.858160] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.864999] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.871009] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.878120] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[ 1.887150] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.896349] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.896354] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.900286] ALSA device list:
[ 1.900290] No soundcards found.
[ 1.916721] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.945738] UBIFS: recovery needed
[ 2.025327] UBIFS: recovery completed
[ 2.029042] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.034966] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.044107] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.053986] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.059025] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[ 2.070536] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.077957] devtmpfs: mounted
[ 2.081059] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.925441] random: dd urandom read with 0 bits of entropy available
[ 3.316904]
[ 3.316904] bcm54xx_config_init
[ 3.926912]
[ 3.926912] bcm54xx_config_init
[ 7.927748] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.933839] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 24.403255] In axi fpga driver!
[ 24.406322] request_mem_region OK!
[ 24.409755] AXI fpga dev virtual address is 0xdf9fc000
[ 24.414820] *base_vir_addr = 0x8c510
[ 24.430453] In fpga mem driver!
[ 24.433526] request_mem_region OK!
[ 24.437116] fpga mem virtual address is 0xe2000000
[ 25.226899]
[ 25.226899] bcm54xx_config_init
[ 25.856891]
[ 25.856891] bcm54xx_config_init
[ 29.857737] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 29.863755] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1299.566050] random: nonblocking pool is initialized
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 803825896600881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[0] has core num=1
Chain[5] ASIC[23] has core num=1
Chain[5] ASIC[24] has core num=1
Chain[5] ASIC[25] has core num=1
Chain[5] ASIC[26] has core num=1
Chain[5] ASIC[27] has core num=1
Chain[5] ASIC[28] has core num=1
Chain[5] ASIC[29] has core num=15
Chain[5] ASIC[30] has core num=3
Chain[5] ASIC[31] has core num=1
Chain[5] ASIC[32] has core num=1
Chain[5] ASIC[33] has core num=1
Chain[5] ASIC[34] has core num=1
Chain[5] ASIC[35] has core num=2
Chain[5] ASIC[36] has core num=1
Chain[5] ASIC[37] has core num=2
Chain[5] ASIC[38] has core num=3
Chain[5] ASIC[39] has core num=1
Chain[5] ASIC[41] has core num=2
Chain[5] ASIC[58] has core num=2
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[0] has core num=1
Chain[6] ASIC[1] has core num=1
Chain[6] ASIC[2] has core num=3
Chain[6] ASIC[27] has core num=1
Chain[6] ASIC[29] has core num=2
Chain[6] ASIC[30] has core num=2
Chain[6] ASIC[31] has core num=2
Chain[6] ASIC[57] has core num=2
Chain[6] ASIC[58] has core num=1
Chain[6] ASIC[59] has core num=2
Chain[6] ASIC[60] has core num=1
Chain[6] ASIC[61] has core num=2
Chain[6] ASIC[62] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 4891 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found= 5111 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found=24638 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 803825896600881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[2] speed=4920
get fan[5] speed=5640
get fan[2] speed=4920
get fan[5] speed=5640
get fan[2] speed=4920
get fan[5] speed=5640
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=74 value=900
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
Chain[J7] orignal chain_voltage_pic=74 value=900
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
Chain[J8] orignal chain_voltage_pic=74 value=900
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[0] has core num=1
Chain[J6] ASIC[23] has core num=1
Chain[J6] ASIC[24] has core num=1
Chain[J6] ASIC[25] has core num=1
Chain[J6] ASIC[26] has core num=1
Chain[J6] ASIC[27] has core num=1
Chain[J6] ASIC[28] has core num=1
Chain[J6] ASIC[29] has core num=15
Chain[J6] ASIC[30] has core num=3
Chain[J6] ASIC[31] has core num=1
Chain[J6] ASIC[32] has core num=1
Chain[J6] ASIC[33] has core num=1
Chain[J6] ASIC[34] has core num=1
Chain[J6] ASIC[35] has core num=2
Chain[J6] ASIC[36] has core num=1
Chain[J6] ASIC[37] has core num=2
Chain[J6] ASIC[38] has core num=3
Chain[J6] ASIC[39] has core num=1
Chain[J6] ASIC[41] has core num=2
Chain[J6] ASIC[58] has core num=2
Chain[J7] has core num in PIC
Chain[J7] ASIC[0] has core num=1
Chain[J7] ASIC[1] has core num=1
Chain[J7] ASIC[2] has core num=3
Chain[J7] ASIC[27] has core num=1
Chain[J7] ASIC[29] has core num=2
Chain[J7] ASIC[30] has core num=2
Chain[J7] ASIC[31] has core num=2
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[58] has core num=1
Chain[J7] ASIC[59] has core num=2
Chain[J7] ASIC[60] has core num=1
Chain[J7] ASIC[61] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
miner total rate=14069GH/s fixed rate=14000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:668
Asic[ 1]:668 Asic[ 2]:668 Asic[ 3]:668 Asic[ 4]:668 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Asic[47]:668 Asic[48]:668
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668
Chain:5 max freq=668
Chain:5 min freq=668
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=656
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=656
Chain:6 min freq=656
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:668
Asic[ 1]:668 Asic[ 2]:668 Asic[ 3]:668 Asic[ 4]:668 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Detect a bad chip=29 on chain[5], fixed to 400M
Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Asic[47]:668 Asic[48]:668
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668
Chain:5 max freq=668
Chain:5 min freq=668
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=656
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=656
Chain:6 min freq=656
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
max freq = 668
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:33 remote:36 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:29 remote:31 offset:28
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:28 remote:31 offset:27
Chain[J8] chip[244] get middle temp offset=27 typeID=55
single board rate=4703 voltage limit=870 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 870
single board rate=4697 voltage limit=870 on chain[6]
get PIC voltage=870 on chain[6], check: must be < 870
single board rate=4668 voltage limit=870 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 870
Chain[J6] set working voltage=870 [125]
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
Chain[5] Chip[62] local Temp=36
Chain[5] Chip[62] middle Temp=48
Special fix Chain[5] Chip[62] middle Temp = 51
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=28
Chain[6] Chip[62] local Temp=33
Chain[6] Chip[62] middle Temp=47
Special fix Chain[6] Chip[62] middle Temp = 48
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=27
Chain[7] Chip[62] local Temp=34
Chain[7] Chip[62] middle Temp=46
Special fix Chain[7] Chip[62] middle Temp = 49
Done read temp on Chain[7]
set FAN speed according to: temp_highest=36 temp_top1[PWM_T]=36 temp_top1[TEMP_POS_LOCAL]=36 temp_change=2 fix_fan_steps=0
set normal FAN speed...
FAN PWM: 22
read_temp_func Done!
CRC error counter=0
Kernel log bilgilerini burada paylaşır mısın? ASIC çiplerinde sıkıntı olabilir.
Havuzu değiştirmeyi deneyin bir de Ethernet Kablosunu da değiştirin,Önceki yazdıklarımın tümünü denediniz mi?
Evet hocam. Dünden beri bu bağlanma sorunu var. Sonra birden bağlandı dün taşırken. Daha sonra yeni yerinde önce bilgiler boş geldi sonra ip alamadı. Şimdi yine ip alıyor ancak miner status falan bomboş. Hardware versiyon ve bmminer versiyon kısımlarıda ana ekranda görünmüyor.Edit: 201704270135, 201705031918 ve201705031858 ve 1838 güncellemelerinde “socket connect failed. Connection refused” hatası veriyor. Şuan 1838 yüklü ve hata devam ediyor.
Bir edit daha:
17 kasıma güncelledim soket hatasını gideremeyince.
Hata gitti fakat eskisi gibi yine hardware versiyon ve bmminer versiyon kısmınboş. Miner status kısmı boş.
Havuzu değiştirmeyi deneyin bir de Ethernet Kablosunu da değiştirin,Önceki yazdıklarımın tümünü denediniz mi?
Hocam benim de başıma geldi ancak bendeki sorun PSU'dan kaynaklıydı ve değiştirince herşey normale döndü,PSU değiştirmeyi deneyin ama halen hata alıyorsanız şunları yapın;
- Cihazı tamamen kapatın.
- Parmağınız "IP Reporter" butonunda basılı olarak kalsın
- Sonra Parmağınızı çekmeden cihazın fişini takın çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra parmağınızı çekin.Çalışmaya devam etsin.
Bunu denedikten sonra cihazın Ip'si değişecektir ve Bilgiler görünmeye başlayacaktır.
Eğer yine de IP almadıysa o zaman şunları yapın;
- Cihazı Kapatın (Tüm fanlar durunca) ve 10 saniye sonra tekrar çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra toplu iğneyle "Reset" e 5 saniye basılı tutun (Yeşil ve Kırmızı Led aynı anda yanacak ve sönünce iğneyi çekin)
- Eğer Sistem ekranında halen birşey gözükmüyorsa o zaman en son firmware güncellemesinden önceki (3 mayıs sürümü) güncellemeyi "Upgrade" kısmından yapınız. (Keep Settings seçili olmasın)
Ben bunları denediğimde çözüme ulaşmıştım umarım sorunun çözülür.Kolay gelsin.
Hocam sağolun düzeldi ip sorunu ama şimdide bir türlü bağlanmıyor cihaz. Bugün değişik hatalar almaya başladım. Bu bağlanamama sorunu ile karşılaştınız mı? Gerçi bu bağlanamama sorununu bazı iplerde yaptığını düşünüyordum ama sanırım öylede değilmiş. Yine biraz kapattım eve geldim şimdi. Biraz kapalı kalsın bakalım ne değişecek. - Cihazı tamamen kapatın.
- Parmağınız "IP Reporter" butonunda basılı olarak kalsın
- Sonra Parmağınızı çekmeden cihazın fişini takın çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra parmağınızı çekin.Çalışmaya devam etsin.
Bunu denedikten sonra cihazın Ip'si değişecektir ve Bilgiler görünmeye başlayacaktır.
Eğer yine de IP almadıysa o zaman şunları yapın;
- Cihazı Kapatın (Tüm fanlar durunca) ve 10 saniye sonra tekrar çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra toplu iğneyle "Reset" e 5 saniye basılı tutun (Yeşil ve Kırmızı Led aynı anda yanacak ve sönünce iğneyi çekin)
- Eğer Sistem ekranında halen birşey gözükmüyorsa o zaman en son firmware güncellemesinden önceki (3 mayıs sürümü) güncellemeyi "Upgrade" kısmından yapınız. (Keep Settings seçili olmasın)
Ben bunları denediğimde çözüme ulaşmıştım umarım sorunun çözülür.Kolay gelsin.
Çalıştığında miner status kısmı bomboş kalıyor öyle. 30dk bile bekledim ama internet olmasına rağmen bağlanamadı.
Hocam benim de başıma geldi ancak bendeki sorun PSU'dan kaynaklıydı ve değiştirince herşey normale döndü,PSU değiştirmeyi deneyin ama halen hata alıyorsanız şunları yapın;
- Cihazı tamamen kapatın.
- Parmağınız "IP Reporter" butonunda basılı olarak kalsın
- Sonra Parmağınızı çekmeden cihazın fişini takın çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra parmağınızı çekin.Çalışmaya devam etsin.
Bunu denedikten sonra cihazın Ip'si değişecektir ve Bilgiler görünmeye başlayacaktır.
Eğer yine de IP almadıysa o zaman şunları yapın;
- Cihazı Kapatın (Tüm fanlar durunca) ve 10 saniye sonra tekrar çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra toplu iğneyle "Reset" e 5 saniye basılı tutun (Yeşil ve Kırmızı Led aynı anda yanacak ve sönünce iğneyi çekin)
- Eğer Sistem ekranında halen birşey gözükmüyorsa o zaman en son firmware güncellemesinden önceki (3 mayıs sürümü) güncellemeyi "Upgrade" kısmından yapınız. (Keep Settings seçili olmasın)
Ben bunları denediğimde çözüme ulaşmıştım umarım sorunun çözülür.Kolay gelsin.
- Cihazı tamamen kapatın.
- Parmağınız "IP Reporter" butonunda basılı olarak kalsın
- Sonra Parmağınızı çekmeden cihazın fişini takın çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra parmağınızı çekin.Çalışmaya devam etsin.
Bunu denedikten sonra cihazın Ip'si değişecektir ve Bilgiler görünmeye başlayacaktır.
Eğer yine de IP almadıysa o zaman şunları yapın;
- Cihazı Kapatın (Tüm fanlar durunca) ve 10 saniye sonra tekrar çalıştırın.
- Cihaz çalışmaya başladıktan 10 saniye sonra toplu iğneyle "Reset" e 5 saniye basılı tutun (Yeşil ve Kırmızı Led aynı anda yanacak ve sönünce iğneyi çekin)
- Eğer Sistem ekranında halen birşey gözükmüyorsa o zaman en son firmware güncellemesinden önceki (3 mayıs sürümü) güncellemeyi "Upgrade" kısmından yapınız. (Keep Settings seçili olmasın)
Ben bunları denediğimde çözüme ulaşmıştım umarım sorunun çözülür.Kolay gelsin.
Arkadaşlar bugün s9 um önce bir türlü bağlanmadı. Bir kaç defa reset, ip report falan yaptım. Daha sonra tekrar yer değiştirip son kez denemek istedim çalıştı. Eve getirdim bu sefer aynı sorunu yine yaptı. Ancak şimdi birde ip almıyor. Paneline giremiyorum. Yine biraz dinlenmeye bıraktım kapatıp. Bu sorunla karşılaşan, çözen, çözümünü bilen var mı?
Edit: şimdide yine ip alıyor ancak bağlanmıyor bir türlü
Edit: şimdide yine ip alıyor ancak bağlanmıyor bir türlü
Jump to: