I haven't heard of it being done on an S9 yet but you can try the boot from microsd option. I had actually ordered a new microsd card and adapter to try this but before the stuff arrived I had figured out a solution for my issue so I never tried it.
https://bitmain.zendesk.com/hc/en-us/articles/204339655-How-to-create-a-bootable-MicroSD-card-with-factory-setting-
Topic: S9 Possible Bricked Controller Bounty (Read 849 times)
Is it possible to access the controllers on these units via serial connection? If so, you could grab a cheap UART to USB adapter from somewhere like SparkFun and see if you're able to open a terminal connection.
How about I ship a controller to you.
or contact bitmainwarranty.com for a spare one or two controllers
https://bitmainwarranty.com/shop/
you need the 98 dollar part and the 20 dollar part. on that parts page
they would also repair your controller
or contact bitmainwarranty.com for a spare one or two controllers
https://bitmainwarranty.com/shop/
you need the 98 dollar part and the 20 dollar part. on that parts page
they would also repair your controller
I have every intention of buying a few spares. I'm working with the warranty now. Just figured i would see if there was a solution beside going through the warranty that anyone knew of.
And consider doing a static config in your DHCP server.
How about I ship a controller to you.
or contact bitmainwarranty.com for a spare one or two controllers
https://bitmainwarranty.com/shop/
you need the 98 dollar part and the 20 dollar part. on that parts page
they would also repair your controller
or contact bitmainwarranty.com for a spare one or two controllers
https://bitmainwarranty.com/shop/
you need the 98 dollar part and the 20 dollar part. on that parts page
they would also repair your controller
The antminer s9 in particular we are having issues with is kinda a fluke. it won't ID on the network no hashing board light up when you push the reset both green and red lights go on. Ip scanners don't Pick up the miner that is having the issue but pick up all the others.
So first of let me say what my team has attempted to do thus far.
Power on let run for 20 min. Attempt to reset by hold down reset for 10 seconds. - No change
Access Restore options from the device its self (Pull up previous ip address that miner has used and it will pull up the standard miner page but half of the options won't load.)
Swapped out PDU PSU every cable from miner to switch and back to outlet. still no gas.
we believe it was caused by a error when the Static IP was being set as two of the 20 miners had this same issue. The second miner has the exact same issue and was located at a different location. The only common factor is the update on the static ip. It was successful for all the other miners but 2. we normally try and make a transition like that slowly so that it can be monitored. but for what ever reason these two miners didn't react as planned. Any recommendations on this would be a great help. Thanks in advance.
Bounty is set at .5btc for anyone that can fix this issue.
So first of let me say what my team has attempted to do thus far.
Power on let run for 20 min. Attempt to reset by hold down reset for 10 seconds. - No change
Access Restore options from the device its self (Pull up previous ip address that miner has used and it will pull up the standard miner page but half of the options won't load.)
Swapped out PDU PSU every cable from miner to switch and back to outlet. still no gas.
we believe it was caused by a error when the Static IP was being set as two of the 20 miners had this same issue. The second miner has the exact same issue and was located at a different location. The only common factor is the update on the static ip. It was successful for all the other miners but 2. we normally try and make a transition like that slowly so that it can be monitored. but for what ever reason these two miners didn't react as planned. Any recommendations on this would be a great help. Thanks in advance.
Bounty is set at .5btc for anyone that can fix this issue.
Jump to: