Topic: s9j works fine but one of fans shows 30,600 RPM...help please (Read 142 times)
thanks alot hockeybum.
This happened to two of my gears but only after i replaced a fan on each, unfortunately for me the miner did not work and it was stuck at "checking fans" phase, it was also showing 30k RPM.
For one miner I replaced the other fan with the another new fan ( the same type that shows 30k) and both started to show 6k RPM and worked fine, for the other gear I had to use another fan, but as the comment above mentioned, if temps are good and miner isn't drifting ( mine was drifting for real) then i wouldn't worry about it.
For one miner I replaced the other fan with the another new fan ( the same type that shows 30k) and both started to show 6k RPM and worked fine, for the other gear I had to use another fan, but as the comment above mentioned, if temps are good and miner isn't drifting ( mine was drifting for real) then i wouldn't worry about it.
The fan sensor isn't working but the fan may still be spinning on its own power. It's definitely not spinning at 18k or 30k RPM because if it was, it would destroy itself. If the temps are okay, you are getting good airflow, and the miner isn't shutting off due to high temps or a no fan signal you will be fine.
hi everyone
i would be so thankful if anybody help.
one of my s9j fans shows 30,600 or 18,000 and ... RPM.
and temp is good and it works fine.
should i change fan with new one?
by the way s9j has 2 fans fan no5 and 6.
this is fan no5 with problem.
please can anybody help?
i would be so thankful if anybody help.
one of my s9j fans shows 30,600 or 18,000 and ... RPM.
and temp is good and it works fine.
should i change fan with new one?
by the way s9j has 2 fans fan no5 and 6.
this is fan no5 with problem.
please can anybody help?
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000292] ps7-ttc #0 at df804000, irq=43
[ 0.000594] Console: colour dummy device 80x30
[ 0.000623] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090237] pid_max: default: 32768 minimum: 301
[ 0.090452] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090471] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092660] CPU: Testing write buffer coherency: ok
[ 0.092984] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093042] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.093262] L310 cache controller enabled
[ 0.093281] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.170985] CPU1: Booted secondary processor
[ 0.260216] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260347] Brought up 2 CPUs
[ 0.260366] SMP: Total of 2 processors activated.
[ 0.260375] CPU: All CPU(s) started in SVC mode.
[ 0.261037] devtmpfs: initialized
[ 0.263470] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264669] regulator-dummy: no parameters
[ 0.272074] NET: Registered protocol family 16
[ 0.274303] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276570] cpuidle: using governor ladder
[ 0.276583] cpuidle: using governor menu
[ 0.283986] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.285504] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.285518] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285631] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.307347] bio: create slab at 0
[ 0.308751] vgaarb: loaded
[ 0.309476] SCSI subsystem initialized
[ 0.310493] usbcore: registered new interface driver usbfs
[ 0.310673] usbcore: registered new interface driver hub
[ 0.310899] usbcore: registered new device driver usb
[ 0.311502] media: Linux media interface: v0.10
[ 0.311661] Linux video capture interface: v2.00
[ 0.311898] pps_core: LinuxPPS API ver. 1 registered
[ 0.311910] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.312033] PTP clock support registered
[ 0.312382] EDAC MC: Ver: 3.0.0
[ 0.313582] Advanced Linux Sound Architecture Driver Initialized.
[ 0.316335] DMA-API: preallocated 4096 debug entries
[ 0.316349] DMA-API: debugging enabled by kernel config
[ 0.316424] Switched to clocksource arm_global_timer
[ 0.337479] NET: Registered protocol family 2
[ 0.338137] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.338195] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.338280] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.338327] TCP: reno registered
[ 0.338344] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.338375] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.338607] NET: Registered protocol family 1
[ 0.338938] RPC: Registered named UNIX socket transport module.
[ 0.338950] RPC: Registered udp transport module.
[ 0.338958] RPC: Registered tcp transport module.
[ 0.338967] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338979] PCI: CLS 0 bytes, default 64
[ 0.339404] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.341401] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.343456] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.343657] msgmni has been set to 967
[ 0.344422] io scheduler noop registered
[ 0.344435] io scheduler deadline registered
[ 0.344475] io scheduler cfq registered (default)
[ 0.353933] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.353953] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.480226] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.047890] console [ttyPS0] enabled
[ 1.052159] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.059782] [drm] Initialized drm 1.1.0 20060810
[ 1.076791] brd: module loaded
[ 1.086138] loop: module loaded
[ 1.095585] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.101570] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.109428] libphy: XEMACPS mii bus: probed
[ 1.113799] ------------- phy_id = 0x3625e62
[ 1.118743] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.127467] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.134083] ehci-pci: EHCI PCI platform driver
[ 1.141313] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.148162] usbcore: registered new interface driver usb-storage
[ 1.154999] mousedev: PS/2 mouse device common for all mice
[ 1.161131] i2c /dev entries driver
[ 1.168092] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.173567] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.179479] Xilinx Zynq CpuIdle Driver started
[ 1.184313] sdhci: Secure Digital Host Controller Interface driver
[ 1.190467] sdhci: Copyright(c) Pierre Ossman
[ 1.194748] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.201592] mmc0: no vqmmc regulator found
[ 1.205610] mmc0: no vmmc regulator found
[ 1.246443] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.255122] usbcore: registered new interface driver usbhid
[ 1.260635] usbhid: USB HID core driver
[ 1.265337] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 1.271631] nand: Macronix MX30LF2G18AC
[ 1.275431] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281566] Bad block table found at page 130944, version 0x02
[ 1.287946] Bad block table found at page 130880, version 0x02
[ 1.293900] nand_read_bbt: bad block at 0x000000a80000
[ 1.299001] nand_read_bbt: bad block at 0x00000f180000
[ 1.304124] 3 ofpart partitions found on MTD device pl353-nand
[ 1.309923] Creating 3 MTD partitions on "pl353-nand":
[ 1.315020] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.323076] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.330396] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.341151] TCP: cubic registered
[ 1.344386] NET: Registered protocol family 17
[ 1.349094] Registering SWP/SWPB emulation handler
[ 1.354972] regulator-dummy: disabling
[ 1.359302] UBI: attaching mtd1 to ubi0
[ 1.704647] UBI: scanning is finished
[ 1.715991] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.723077] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.729838] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.736524] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.743360] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.749361] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.756484] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 251762771
[ 1.765408] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.774641] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.774647] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.778662] ALSA device list:
[ 1.778666] No soundcards found.
[ 1.795776] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.917086] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.923018] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.932150] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.942034] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.947074] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C32C42B1-7C6A-4282-B572-CDE010B46701, small LPT model
[ 1.967895] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.027708] devtmpfs: mounted
[ 2.030819] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 3.140777] random: dd urandom read with 1 bits of entropy available
[ 3.726442]
[ 3.726442] bcm54xx_config_init
[ 4.336443]
[ 4.336443] bcm54xx_config_init
[ 7.337292] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.343383] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 40.456550] In axi fpga driver!
[ 40.459620] request_mem_region OK!
[ 40.463010] AXI fpga dev virtual address is 0xdf9fe000
[ 40.468150] *base_vir_addr = 0xc51e
[ 40.482732] In fpga mem driver!
[ 40.486061] request_mem_region OK!
[ 40.489674] fpga mem virtual address is 0xe2000000
[ 41.256447]
[ 41.256447] bcm54xx_config_init
[ 41.886461]
[ 41.886461] bcm54xx_config_init
[ 44.887313] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 44.893328] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 638.893552] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram: 507486208
Detect 512MB control board of XILINX
mmap axi_fpga_addr = 0xb6f42000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5d3b000
forceFreq=-1 forceFlag=0
min work minertest[0]:912
DETECT HW version=0000c51e
miner ID : 804895892f90481c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Check chain[5] PIC fw version=0x03
read pic freq and badcore num...
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Check chain[6] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x03
get PIC voltage=23 on chain[5], value=930
get PIC voltage=6 on chain[6], value=940
get PIC voltage=6 on chain[7], value=940
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 3
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found=27867 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Mon Mar 4 11:54:07 CST 2019 type: Antminer S9j
miner ID : 804895892f90481c
Checking fans...
get fan[4] speed=11160
get fan[4] speed=11160
get fan[5] speed=6120
get fan[4] speed=11160
get fan[5] speed=6120
get fan[4] speed=11160
get fan[5] speed=6120
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0e 0x4e 0x0e 0x4e 0x02 0x4e 0x01 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has lpm backup chain_voltage=860
scan based on domain
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0f 0x4e 0x0e 0x4e 0x02 0x4e 0x01 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has lpm backup chain_voltage=860
scan based on domain
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0f 0x4e 0x0e 0x4e 0x02 0x4e 0x01 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has lpm backup chain_voltage=860
scan based on domain
Check chain[7] PIC fw version=0x03
total_exist_chain_num = 3
Chain[J6] orignal chain_voltage_pic=23 value=930
Chain[J6] will use backup chain_voltage_pic=860 [142]
Chain[J6] get working chain_voltage_pic=142
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=860 [142]
Chain[J7] get working chain_voltage_pic=142
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=860 [142]
Chain[J8] get working chain_voltage_pic=142
Chain[J6] has 0 asic
retry Chain[J6] has 0 asic
retry Chain[J6] has 0 asic
retry Chain[J6] has 0 asic
retry Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J7] has core num in PIC
Chain[J8] has core num in PIC
totalrate = 14540
miner total rate=14540GH/s ideal_total_hash_rate = 14500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:5 max freq=675
Chain:5 min freq=675
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:6 max freq=675
Chain:6 min freq=675
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:7 max freq=675
Chain:7 min freq=675
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:5 max freq=675
Chain:5 min freq=675
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:6 max freq=675
Chain:6 min freq=675
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:7 max freq=675
Chain:7 min freq=675
max freq = 675
totalRate = 14500, fixed_totalRate = 14500
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:26 remote:29 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:26 remote:29 offset:27
Chain[J7] chip[244] get middle temp offset=27 typeID=55
Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[8] chip[244] local:25 remote:29 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
open core three times
open core three times
open core three times
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
chain[5] set voltage to 870
chain[6] set voltage to 870
chain[7] set voltage to 870
chain[5] set voltage to 860
chain[6] set voltage to 860
chain[7] set voltage to 860
start thread for read temp
setStartTimePoint total_tv_start_sys=623 total_tv_end_sys=624
restartNum = 2 , auto-reinit enabled...
bring_up_pcb_temp = 50
setting to working voltage...
voltage_check_done
avg hash rate = 14521.133690, ideal hash rate = 14500
hash rate is ok now
Fatal Error: network connection lost!
max pcb temperature:57, fan num:2, error counter:1
avg_rate = 14371, ideal_total_hash_rate = 14500
avg_rate = 14388, ideal_total_hash_rate = 14500
do read_temp_func once...
get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=76.5540 Asic[02]=73.8020 Asic[03]=80.8660 Asic[04]=71.4870 Asic[05]=77.4430 Asic[06]=74.5410 Asic[07]=82.8960 Asic[08]=77.2920
Asic[09]=76.4030 Asic[10]=70.7990 Asic[11]=77.7790 Asic[12]=79.9430 Asic[13]=76.5370 Asic[14]=80.3960 Asic[15]=75.2120 Asic[16]=80.3960
Asic[17]=77.3090 Asic[18]=77.9800 Asic[19]=78.7850 Asic[20]=77.8790 Asic[21]=75.0270 Asic[22]=76.6880 Asic[23]=79.5240 Asic[24]=78.1480
Asic[25]=77.7620 Asic[26]=73.8190 Asic[27]=80.1950 Asic[28]=81.5200 Asic[29]=82.5770 Asic[30]=76.9060 Asic[31]=77.5440 Asic[32]=77.3260
Asic[33]=79.8930 Asic[34]=83.5500 Asic[35]=74.5740 Asic[36]=69.6750 Asic[37]=75.8660 Asic[38]=80.3790 Asic[39]=74.2550 Asic[40]=78.2150
Asic[41]=74.0540 Asic[42]=83.4490 Asic[43]=80.9330 Asic[44]=78.3830 Asic[45]=77.0740 Asic[46]=73.7020 Asic[47]=77.6780 Asic[48]=79.8590
Asic[49]=77.2920 Asic[50]=76.9900 Asic[51]=76.0000 Asic[52]=74.7250 Asic[53]=81.2010 Asic[54]=78.3660 Asic[55]=77.4260 Asic[56]=75.6820
Asic[57]=72.0070 Asic[58]=72.2590 Asic[59]=73.5680 Asic[60]=71.3530 Asic[61]=79.1540 Asic[62]=80.1950 Asic[63]=82.0070
get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=75.5140 Asic[02]=74.5240 Asic[03]=81.2850 Asic[04]=74.8590 Asic[05]=80.2780 Asic[06]=79.9600 Asic[07]=78.9870 Asic[08]=79.6580
Asic[09]=77.2920 Asic[10]=73.8860 Asic[11]=71.9400 Asic[12]=81.0170 Asic[13]=77.8460 Asic[14]=76.5200 Asic[15]=72.8130 Asic[16]=75.3960
Asic[17]=74.7920 Asic[18]=73.6680 Asic[19]=78.2320 Asic[20]=83.7350 Asic[21]=76.5200 Asic[22]=81.6370 Asic[23]=70.6820 Asic[24]=80.2780
Asic[25]=77.0070 Asic[26]=81.4190 Asic[27]=82.0900 Asic[28]=78.1810 Asic[29]=76.8220 Asic[30]=71.8560 Asic[31]=71.5540 Asic[32]=76.3190
Asic[33]=77.9630 Asic[34]=79.5240 Asic[35]=81.2520 Asic[36]=80.7820 Asic[37]=78.7520 Asic[38]=75.4130 Asic[39]=76.2180 Asic[40]=79.9760
Asic[41]=76.2180 Asic[42]=76.7890 Asic[43]=74.2720 Asic[44]=78.7850 Asic[45]=75.8490 Asic[46]=75.0940 Asic[47]=82.3250 Asic[48]=78.8020
Asic[49]=76.5370 Asic[50]=73.6010 Asic[51]=73.8020 Asic[52]=74.9770 Asic[53]=76.8060 Asic[54]=73.9030 Asic[55]=76.5040 Asic[56]=76.5200
Asic[57]=74.6080 Asic[58]=81.1840 Asic[59]=80.5640 Asic[60]=81.8050 Asic[61]=80.8320 Asic[62]=83.7350 Asic[63]=76.1010
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=82.3760 Asic[02]=78.0970 Asic[03]=74.0880 Asic[04]=74.9270 Asic[05]=72.8290 Asic[06]=77.0740 Asic[07]=76.3860 Asic[08]=74.1880
Asic[09]=73.8860 Asic[10]=72.2760 Asic[11]=75.2290 Asic[12]=83.9360 Asic[13]=79.1380 Asic[14]=78.8690 Asic[15]=74.6250 Asic[16]=80.3460
Asic[17]=75.4470 Asic[18]=75.2450 Asic[19]=77.8460 Asic[20]=74.3560 Asic[21]=77.8460 Asic[22]=81.6710 Asic[23]=74.1210 Asic[24]=70.6820
Asic[25]=74.1210 Asic[26]=77.5940 Asic[27]=73.2490 Asic[28]=74.5070 Asic[29]=79.0710 Asic[30]=78.5170 Asic[31]=79.7920 Asic[32]=83.7010
Asic[33]=74.8260 Asic[34]=79.1540 Asic[35]=75.8490 Asic[36]=78.2320 Asic[37]=77.8120 Asic[38]=79.5240 Asic[39]=75.4630 Asic[40]=79.8590
Asic[41]=81.3020 Asic[42]=76.9060 Asic[43]=76.8060 Asic[44]=76.7890 Asic[45]=78.1140 Asic[46]=77.2750 Asic[47]=74.2220 Asic[48]=75.8490
Asic[49]=79.5910 Asic[50]=77.1910 Asic[51]=77.4930 Asic[52]=75.5640 Asic[53]=79.9930 Asic[54]=77.9970 Asic[55]=72.3090 Asic[56]=78.8520
Asic[57]=72.6280 Asic[58]=74.6580 Asic[59]=78.2320 Asic[60]=74.1210 Asic[61]=79.1210 Asic[62]=88.4150 Asic[63]=74.0040
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
Chain[5] Chip[244] pcb temperature=57
Chain[5] Chip[62] junction temperature=63
Special fix Chain[5] Chip[62] middle Temp = 72
Done read temp on Chain[5]
Chain[6] Chip[244] pcb temperature=52
Chain[6] Chip[62] junction temperature=59
Special fix Chain[6] Chip[62] middle Temp = 67
Done read temp on Chain[6]
Chain[7] Chip[244] pcb temperature=56
Chain[7] Chip[62] junction temperature=62
Special fix Chain[7] Chip[62] middle Temp = 71
Done read temp on Chain[7]
Max pcb temp : 57
set FAN speed according to: temp_highest=57 temp_top1[PWM_T]=57 temp_top1[TEMP_POS_LOCAL]=57 temp_change=-1 fix_fan_steps=0
FAN PWM: 57
read_temp_func Done!
CRC error counter=8166
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000292] ps7-ttc #0 at df804000, irq=43
[ 0.000594] Console: colour dummy device 80x30
[ 0.000623] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090237] pid_max: default: 32768 minimum: 301
[ 0.090452] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090471] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092660] CPU: Testing write buffer coherency: ok
[ 0.092984] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093042] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.093262] L310 cache controller enabled
[ 0.093281] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.170985] CPU1: Booted secondary processor
[ 0.260216] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260347] Brought up 2 CPUs
[ 0.260366] SMP: Total of 2 processors activated.
[ 0.260375] CPU: All CPU(s) started in SVC mode.
[ 0.261037] devtmpfs: initialized
[ 0.263470] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264669] regulator-dummy: no parameters
[ 0.272074] NET: Registered protocol family 16
[ 0.274303] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276570] cpuidle: using governor ladder
[ 0.276583] cpuidle: using governor menu
[ 0.283986] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.285504] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.285518] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285631] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.307347] bio: create slab
[ 0.308751] vgaarb: loaded
[ 0.309476] SCSI subsystem initialized
[ 0.310493] usbcore: registered new interface driver usbfs
[ 0.310673] usbcore: registered new interface driver hub
[ 0.310899] usbcore: registered new device driver usb
[ 0.311502] media: Linux media interface: v0.10
[ 0.311661] Linux video capture interface: v2.00
[ 0.311898] pps_core: LinuxPPS API ver. 1 registered
[ 0.311910] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.312033] PTP clock support registered
[ 0.312382] EDAC MC: Ver: 3.0.0
[ 0.313582] Advanced Linux Sound Architecture Driver Initialized.
[ 0.316335] DMA-API: preallocated 4096 debug entries
[ 0.316349] DMA-API: debugging enabled by kernel config
[ 0.316424] Switched to clocksource arm_global_timer
[ 0.337479] NET: Registered protocol family 2
[ 0.338137] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.338195] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.338280] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.338327] TCP: reno registered
[ 0.338344] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.338375] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.338607] NET: Registered protocol family 1
[ 0.338938] RPC: Registered named UNIX socket transport module.
[ 0.338950] RPC: Registered udp transport module.
[ 0.338958] RPC: Registered tcp transport module.
[ 0.338967] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338979] PCI: CLS 0 bytes, default 64
[ 0.339404] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.341401] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.343456] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.343657] msgmni has been set to 967
[ 0.344422] io scheduler noop registered
[ 0.344435] io scheduler deadline registered
[ 0.344475] io scheduler cfq registered (default)
[ 0.353933] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.353953] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.480226] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.047890] console [ttyPS0] enabled
[ 1.052159] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.059782] [drm] Initialized drm 1.1.0 20060810
[ 1.076791] brd: module loaded
[ 1.086138] loop: module loaded
[ 1.095585] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.101570] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.109428] libphy: XEMACPS mii bus: probed
[ 1.113799] ------------- phy_id = 0x3625e62
[ 1.118743] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.127467] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.134083] ehci-pci: EHCI PCI platform driver
[ 1.141313] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.148162] usbcore: registered new interface driver usb-storage
[ 1.154999] mousedev: PS/2 mouse device common for all mice
[ 1.161131] i2c /dev entries driver
[ 1.168092] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.173567] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.179479] Xilinx Zynq CpuIdle Driver started
[ 1.184313] sdhci: Secure Digital Host Controller Interface driver
[ 1.190467] sdhci: Copyright(c) Pierre Ossman
[ 1.194748] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.201592] mmc0: no vqmmc regulator found
[ 1.205610] mmc0: no vmmc regulator found
[ 1.246443] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.255122] usbcore: registered new interface driver usbhid
[ 1.260635] usbhid: USB HID core driver
[ 1.265337] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 1.271631] nand: Macronix MX30LF2G18AC
[ 1.275431] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281566] Bad block table found at page 130944, version 0x02
[ 1.287946] Bad block table found at page 130880, version 0x02
[ 1.293900] nand_read_bbt: bad block at 0x000000a80000
[ 1.299001] nand_read_bbt: bad block at 0x00000f180000
[ 1.304124] 3 ofpart partitions found on MTD device pl353-nand
[ 1.309923] Creating 3 MTD partitions on "pl353-nand":
[ 1.315020] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.323076] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.330396] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.341151] TCP: cubic registered
[ 1.344386] NET: Registered protocol family 17
[ 1.349094] Registering SWP/SWPB emulation handler
[ 1.354972] regulator-dummy: disabling
[ 1.359302] UBI: attaching mtd1 to ubi0
[ 1.704647] UBI: scanning is finished
[ 1.715991] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.723077] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.729838] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.736524] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.743360] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.749361] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.756484] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 251762771
[ 1.765408] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.774641] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.774647] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.778662] ALSA device list:
[ 1.778666] No soundcards found.
[ 1.795776] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.917086] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.923018] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.932150] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.942034] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.947074] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C32C42B1-7C6A-4282-B572-CDE010B46701, small LPT model
[ 1.967895] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.027708] devtmpfs: mounted
[ 2.030819] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 3.140777] random: dd urandom read with 1 bits of entropy available
[ 3.726442]
[ 3.726442] bcm54xx_config_init
[ 4.336443]
[ 4.336443] bcm54xx_config_init
[ 7.337292] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.343383] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 40.456550] In axi fpga driver!
[ 40.459620] request_mem_region OK!
[ 40.463010] AXI fpga dev virtual address is 0xdf9fe000
[ 40.468150] *base_vir_addr = 0xc51e
[ 40.482732] In fpga mem driver!
[ 40.486061] request_mem_region OK!
[ 40.489674] fpga mem virtual address is 0xe2000000
[ 41.256447]
[ 41.256447] bcm54xx_config_init
[ 41.886461]
[ 41.886461] bcm54xx_config_init
[ 44.887313] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 44.893328] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 638.893552] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram: 507486208
Detect 512MB control board of XILINX
mmap axi_fpga_addr = 0xb6f42000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5d3b000
forceFreq=-1 forceFlag=0
min work minertest[0]:912
DETECT HW version=0000c51e
miner ID : 804895892f90481c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Check chain[5] PIC fw version=0x03
read pic freq and badcore num...
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Check chain[6] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x03
get PIC voltage=23 on chain[5], value=930
get PIC voltage=6 on chain[6], value=940
get PIC voltage=6 on chain[7], value=940
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 3
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found=27867 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Mon Mar 4 11:54:07 CST 2019 type: Antminer S9j
miner ID : 804895892f90481c
Checking fans...
get fan[4] speed=11160
get fan[4] speed=11160
get fan[5] speed=6120
get fan[4] speed=11160
get fan[5] speed=6120
get fan[4] speed=11160
get fan[5] speed=6120
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0e 0x4e 0x0e 0x4e 0x02 0x4e 0x01 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has lpm backup chain_voltage=860
scan based on domain
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0f 0x4e 0x0e 0x4e 0x02 0x4e 0x01 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has lpm backup chain_voltage=860
scan based on domain
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0f 0x4e 0x0e 0x4e 0x02 0x4e 0x01 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has lpm backup chain_voltage=860
scan based on domain
Check chain[7] PIC fw version=0x03
total_exist_chain_num = 3
Chain[J6] orignal chain_voltage_pic=23 value=930
Chain[J6] will use backup chain_voltage_pic=860 [142]
Chain[J6] get working chain_voltage_pic=142
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=860 [142]
Chain[J7] get working chain_voltage_pic=142
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=860 [142]
Chain[J8] get working chain_voltage_pic=142
Chain[J6] has 0 asic
retry Chain[J6] has 0 asic
retry Chain[J6] has 0 asic
retry Chain[J6] has 0 asic
retry Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J7] has core num in PIC
Chain[J8] has core num in PIC
totalrate = 14540
miner total rate=14540GH/s ideal_total_hash_rate = 14500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:5 max freq=675
Chain:5 min freq=675
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:6 max freq=675
Chain:6 min freq=675
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:7 max freq=675
Chain:7 min freq=675
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:5 max freq=675
Chain:5 min freq=675
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:6 max freq=675
Chain:6 min freq=675
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=100
Asic[ 0]:675 Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675
Asic[ 8]:675 Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675
Asic[16]:675 Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675
Asic[24]:675 Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675
Asic[32]:675 Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675
Asic[40]:675 Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675
Asic[48]:675 Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675
Asic[56]:675 Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:7 max freq=675
Chain:7 min freq=675
max freq = 675
totalRate = 14500, fixed_totalRate = 14500
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:26 remote:29 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:26 remote:29 offset:27
Chain[J7] chip[244] get middle temp offset=27 typeID=55
Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[8] chip[244] local:25 remote:29 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
open core three times
open core three times
open core three times
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
chain[5] set voltage to 870
chain[6] set voltage to 870
chain[7] set voltage to 870
chain[5] set voltage to 860
chain[6] set voltage to 860
chain[7] set voltage to 860
start thread for read temp
setStartTimePoint total_tv_start_sys=623 total_tv_end_sys=624
restartNum = 2 , auto-reinit enabled...
bring_up_pcb_temp = 50
setting to working voltage...
voltage_check_done
avg hash rate = 14521.133690, ideal hash rate = 14500
hash rate is ok now
Fatal Error: network connection lost!
max pcb temperature:57, fan num:2, error counter:1
avg_rate = 14371, ideal_total_hash_rate = 14500
avg_rate = 14388, ideal_total_hash_rate = 14500
do read_temp_func once...
get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=76.5540 Asic[02]=73.8020 Asic[03]=80.8660 Asic[04]=71.4870 Asic[05]=77.4430 Asic[06]=74.5410 Asic[07]=82.8960 Asic[08]=77.2920
Asic[09]=76.4030 Asic[10]=70.7990 Asic[11]=77.7790 Asic[12]=79.9430 Asic[13]=76.5370 Asic[14]=80.3960 Asic[15]=75.2120 Asic[16]=80.3960
Asic[17]=77.3090 Asic[18]=77.9800 Asic[19]=78.7850 Asic[20]=77.8790 Asic[21]=75.0270 Asic[22]=76.6880 Asic[23]=79.5240 Asic[24]=78.1480
Asic[25]=77.7620 Asic[26]=73.8190 Asic[27]=80.1950 Asic[28]=81.5200 Asic[29]=82.5770 Asic[30]=76.9060 Asic[31]=77.5440 Asic[32]=77.3260
Asic[33]=79.8930 Asic[34]=83.5500 Asic[35]=74.5740 Asic[36]=69.6750 Asic[37]=75.8660 Asic[38]=80.3790 Asic[39]=74.2550 Asic[40]=78.2150
Asic[41]=74.0540 Asic[42]=83.4490 Asic[43]=80.9330 Asic[44]=78.3830 Asic[45]=77.0740 Asic[46]=73.7020 Asic[47]=77.6780 Asic[48]=79.8590
Asic[49]=77.2920 Asic[50]=76.9900 Asic[51]=76.0000 Asic[52]=74.7250 Asic[53]=81.2010 Asic[54]=78.3660 Asic[55]=77.4260 Asic[56]=75.6820
Asic[57]=72.0070 Asic[58]=72.2590 Asic[59]=73.5680 Asic[60]=71.3530 Asic[61]=79.1540 Asic[62]=80.1950 Asic[63]=82.0070
get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=75.5140 Asic[02]=74.5240 Asic[03]=81.2850 Asic[04]=74.8590 Asic[05]=80.2780 Asic[06]=79.9600 Asic[07]=78.9870 Asic[08]=79.6580
Asic[09]=77.2920 Asic[10]=73.8860 Asic[11]=71.9400 Asic[12]=81.0170 Asic[13]=77.8460 Asic[14]=76.5200 Asic[15]=72.8130 Asic[16]=75.3960
Asic[17]=74.7920 Asic[18]=73.6680 Asic[19]=78.2320 Asic[20]=83.7350 Asic[21]=76.5200 Asic[22]=81.6370 Asic[23]=70.6820 Asic[24]=80.2780
Asic[25]=77.0070 Asic[26]=81.4190 Asic[27]=82.0900 Asic[28]=78.1810 Asic[29]=76.8220 Asic[30]=71.8560 Asic[31]=71.5540 Asic[32]=76.3190
Asic[33]=77.9630 Asic[34]=79.5240 Asic[35]=81.2520 Asic[36]=80.7820 Asic[37]=78.7520 Asic[38]=75.4130 Asic[39]=76.2180 Asic[40]=79.9760
Asic[41]=76.2180 Asic[42]=76.7890 Asic[43]=74.2720 Asic[44]=78.7850 Asic[45]=75.8490 Asic[46]=75.0940 Asic[47]=82.3250 Asic[48]=78.8020
Asic[49]=76.5370 Asic[50]=73.6010 Asic[51]=73.8020 Asic[52]=74.9770 Asic[53]=76.8060 Asic[54]=73.9030 Asic[55]=76.5040 Asic[56]=76.5200
Asic[57]=74.6080 Asic[58]=81.1840 Asic[59]=80.5640 Asic[60]=81.8050 Asic[61]=80.8320 Asic[62]=83.7350 Asic[63]=76.1010
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=82.3760 Asic[02]=78.0970 Asic[03]=74.0880 Asic[04]=74.9270 Asic[05]=72.8290 Asic[06]=77.0740 Asic[07]=76.3860 Asic[08]=74.1880
Asic[09]=73.8860 Asic[10]=72.2760 Asic[11]=75.2290 Asic[12]=83.9360 Asic[13]=79.1380 Asic[14]=78.8690 Asic[15]=74.6250 Asic[16]=80.3460
Asic[17]=75.4470 Asic[18]=75.2450 Asic[19]=77.8460 Asic[20]=74.3560 Asic[21]=77.8460 Asic[22]=81.6710 Asic[23]=74.1210 Asic[24]=70.6820
Asic[25]=74.1210 Asic[26]=77.5940 Asic[27]=73.2490 Asic[28]=74.5070 Asic[29]=79.0710 Asic[30]=78.5170 Asic[31]=79.7920 Asic[32]=83.7010
Asic[33]=74.8260 Asic[34]=79.1540 Asic[35]=75.8490 Asic[36]=78.2320 Asic[37]=77.8120 Asic[38]=79.5240 Asic[39]=75.4630 Asic[40]=79.8590
Asic[41]=81.3020 Asic[42]=76.9060 Asic[43]=76.8060 Asic[44]=76.7890 Asic[45]=78.1140 Asic[46]=77.2750 Asic[47]=74.2220 Asic[48]=75.8490
Asic[49]=79.5910 Asic[50]=77.1910 Asic[51]=77.4930 Asic[52]=75.5640 Asic[53]=79.9930 Asic[54]=77.9970 Asic[55]=72.3090 Asic[56]=78.8520
Asic[57]=72.6280 Asic[58]=74.6580 Asic[59]=78.2320 Asic[60]=74.1210 Asic[61]=79.1210 Asic[62]=88.4150 Asic[63]=74.0040
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
Chain[5] Chip[244] pcb temperature=57
Chain[5] Chip[62] junction temperature=63
Special fix Chain[5] Chip[62] middle Temp = 72
Done read temp on Chain[5]
Chain[6] Chip[244] pcb temperature=52
Chain[6] Chip[62] junction temperature=59
Special fix Chain[6] Chip[62] middle Temp = 67
Done read temp on Chain[6]
Chain[7] Chip[244] pcb temperature=56
Chain[7] Chip[62] junction temperature=62
Special fix Chain[7] Chip[62] middle Temp = 71
Done read temp on Chain[7]
Max pcb temp : 57
set FAN speed according to: temp_highest=57 temp_top1[PWM_T]=57 temp_top1[TEMP_POS_LOCAL]=57 temp_change=-1 fix_fan_steps=0
FAN PWM: 57
read_temp_func Done!
CRC error counter=8166
Jump to: