Topic: Setup Bitcoin Core for receiving inbound connections (Read 172 times)
Yes. I let it run a day and it's 29 so I guess I'll just wait. Thanks for the support
I already enabled incoming connection and tried to add the maxconnections command to the conf file but none of the procedures worked. Could it be a matter of bandwidth of my interernet connection?
It takes hours or days before someone's nodes start to connect to you and it depends on the router's firewall. It is likely the same as torrent it takes a while before you can see more connections. And take note maxconnection is only for inbounds not for outbound I don't know if there is a command to increase outbound.And please read this Bitcoin by default will not make more than 8 outgoing connections
I already enabled incoming connection and tried to add the maxconnections command to the conf file but none of the procedures worked. Could it be a matter of bandwidth of my interernet connection?
Have you tried to check the settings> of your Bitcoin core?
You can find allow incoming connection enable it and restart the core. Let's see if the inbound connection increases.
If not try to add this to your bitcoin.conf
The 125 value is the default value of max peer connections change it to higher then check for changes.
You can find allow incoming connection enable it and restart the core. Let's see if the inbound connection increases.
If not try to add this to your bitcoin.conf
Code:
maxconnections=125
The 125 value is the default value of max peer connections change it to higher then check for changes.
Thanks all for the replies. It seems like the problem solved by itself. Now the node test on Bitnodes shows green check and I've 5 inbound connections and 10 outbound.
Wondering if I could have more in connections, but it seems like the number is still adjusting at the moment. Outbounds are stable on 10 while inbounds swing from 4 to 6 at the moment.
Wondering if I could have more in connections, but it seems like the number is still adjusting at the moment. Outbounds are stable on 10 while inbounds swing from 4 to 6 at the moment.
-snip-EDIT:
My router also has UPnP enabled and I've tryed to check the "map ports with UPnP" in the GUI, on options, without any result.
So, router and node seem to be configured correctly; also, enabling UPnP usually works after restarting the node.My router also has UPnP enabled and I've tryed to check the "map ports with UPnP" in the GUI, on options, without any result.
I'm guessing that it may have something to do with your ISP.
Check your "debug.log" file if there's any entry that hints of inbound connection attempts.
It's in the data directory, open it as text.
Quote
Do you have any entries in your bitcoin.conf file or the GUI's settings?
No entries. I just tried adding "listen=1" but then deleted it.No entries. I just tried adding "listen=1" but then deleted it.
EDIT:
My router also has UPnP enabled and I've tryed to check the "map ports with UPnP" in the GUI, on options, without any result
Would you mind trying to put listen=1 again under bitcoin.conf file but this time after you save it reopen the bitcoin core and reboot the PC so that the config after restart will load properly.
Also, if your router has anti-DDOS enabled I suggest disable it to try.
Set up your PC network switch to static then add Cloudflare DNS to try.
Quote
Can you provide what is on the image in text?
DHCP Reservation:
Name:
MyDesktopName
Vendor:
Unknown Vendor
MAC Address: MyMacAddress
IP Address (Reserved):
myIPaddress
Reserve IP:
Enabled
Port Forwarding:
Enable Rules:
Enable
Name:
BitcoinNode
Interface:
ATM_PPPoE_0_2
Internal IP:
myIPaddress ()
(Internal IP must be in the same network segment with LAN IP)
Internal startport:
8333
Internal endport:
18333
External startport:
8333
External endport:
18333
Protocol Type:
TCP
Firewall:
step1
protocol type: any
local port: all
remote port: all
step2:
local IP to apply selection:
myIPaddress
Quote
Do you have any entries in your bitcoin.conf file or the GUI's settings?
No entries. I just tried adding "listen=1" but then deleted it.
Quote
Have you restarted the router and PC after setting port forwarding and static IP?
I did it but didn't work.
EDIT:
My router also has UPnP enabled and I've tryed to check the "map ports with UPnP" in the GUI, on options, without any result.
Do you have any entries in your bitcoin.conf file or the GUI's settings?
If there are, please show them (remove the sensitive parts like RPC credentials).
Have you restarted the router and PC after setting port forwarding and static IP?
Depending on the router, it may require a restart.
If there are, please show them (remove the sensitive parts like RPC credentials).
Have you restarted the router and PC after setting port forwarding and static IP?
Depending on the router, it may require a restart.
I cannot see your image hosted at imgur I think they are having problems. Can you provide what is on the image in text? I might be able to help I have had issues with setting up my own node and it was some udev rules that needed to be applied to get it to function.
Hi everyone,
I downloaded BitcoinCore to run a full node. I'm already synchronized with the entire blockchain and followed the istructions (https://bitcoin.org/en/full-node#upgrading-bitcoin-core) to enable inbound connections but even after that I can't see any in the node window.
I wanted to ask you some help to figure out where is the problem. I may have done some mistake during the procedure but I couldn't understand where.
In this link there are the screenshots of the various step I made to allow inbound connctions
https://imgur.com/a/pJkNsoO
pic1: DHCP Reservation
pic2: Port Forwarding
pic3: current status of my firewall inbound connections
pic4 and pic5: creation of a new rule
The IP address that I obscured is the same in pic 1, 2 and 5.
The language is italian. I think you just need to know that "Qualsiasi" means "any" or "all".
Also note that I had only two rules in the firewall at the beginning, but after some time (or something I made) it became two.
Thanks for your time.
I downloaded BitcoinCore to run a full node. I'm already synchronized with the entire blockchain and followed the istructions (https://bitcoin.org/en/full-node#upgrading-bitcoin-core) to enable inbound connections but even after that I can't see any in the node window.
I wanted to ask you some help to figure out where is the problem. I may have done some mistake during the procedure but I couldn't understand where.
In this link there are the screenshots of the various step I made to allow inbound connctions
https://imgur.com/a/pJkNsoO
pic1: DHCP Reservation
pic2: Port Forwarding
pic3: current status of my firewall inbound connections
pic4 and pic5: creation of a new rule
The IP address that I obscured is the same in pic 1, 2 and 5.
The language is italian. I think you just need to know that "Qualsiasi" means "any" or "all".
Also note that I had only two rules in the firewall at the beginning, but after some time (or something I made) it became two.
Thanks for your time.
Jump to: