SOLO Mining HELP | Bitcointalksearch.org

salmanahmedone

hero member

Activity: 602

Merit: 500

Quote from: opies32765 on September 28, 2017, 09:40:53 AM

Guys,

Need some HELP

Trying to mine UBIQ SOLO....

set up 1st computer with the node...even connect a miner on that same computer to the node with no issues...

trying to connect other computers on the same local network to the node...using the first computers IP address 192.168.1.54:8588

using claymore

im getting

ETH: http error #7.
ETH: Failed to connect to pool (192.168.1.54:8588), retry in 20 sec...

has anyone seen this before ?

I even opened a firewall rule with the 8588 port

Thanks in advance

It's not something that you really need to worry about it. If you're insistent on selling just do it through the wallet of the coin by simply setting your generate true. That's the easiest way to sell them at that method right there is not going to be any worse than pointing some other Miner at that coin.

makomako

full member

Activity: 210

Merit: 100

altcom Aa4DWXQjrcEA8gPBLkx6t9VgCuWoCo1myE

Quote from: opies32765 on September 28, 2017, 11:21:29 AM

Ayers

so as below ? Im assuming the allow ip is to the remote computer trying to connect ?

Thanks in advance

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!

-epool http://192.168.1.54:8588
-ewal 0x926957F22b01b2E100078DF71Cf33377E0b0C9a9
-epsw x
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4
#-dpsw x
#-esm 1
-mode 1
#-tt 70
#-asm 0
-rpcallowip=192.168.1.37

Not on your bat file, add the -rpcallowip on your wallets conf file. make sure your rpc port and other details are the same with your config file

opies32765

member

Activity: 88

Merit: 16

Ayers

so as below ? Im assuming the allow ip is to the remote computer trying to connect ?

Thanks in advance

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!

-epool http://192.168.1.54:8588
-ewal 0x926957F22b01b2E100078DF71Cf33377E0b0C9a9
-epsw x
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4
#-dpsw x
#-esm 1
-mode 1
#-tt 70
#-asm 0
-rpcallowip=192.168.1.37

Ayers

legendary

Activity: 2590

Merit: 1022

Leading Crypto Sports Betting & Casino Platform

you need to allow the program via the firewall not just opening the port "allow a program through windows firewall..." etc and on config file you need to add rpcallowip=192.168.1.*

opies32765

member

Activity: 88

Merit: 16

Guys,

Need some HELP

Trying to mine UBIQ SOLO....

set up 1st computer with the node...even connect a miner on that same computer to the node with no issues...

trying to connect other computers on the same local network to the node...using the first computers IP address 192.168.1.54:8588

using claymore

im getting

ETH: http error #7.
ETH: Failed to connect to pool (192.168.1.54:8588), retry in 20 sec...

has anyone seen this before ?

I even opened a firewall rule with the 8588 port

Thanks in advance

Topic: SOLO Mining HELP (Read 640 times)