Topic: T17 is only hashing on one board. (Read 100 times)
They break. It is a fact of life. It may have been fine when he shipped it and it was handled roughly by the shipper.
Ok so I did run each of these individually. I did confirm that card that was warm before was the working one. When I ran the 3rd card it worked. I think this is the card that showed the 25 chip was not working.
I did apply the slightest bit of pressure on all the heatsinks before I put them back. What should I do?
I think it is worth disclosing I bought 2 of these and they are each running on their on 30 amp breaker with their own tripplite PDU. The first one is working fine. So I don't think there is anything wrong with my setup.
1st Card (worked as expected)
2nd card (did not work)
3rd card (Worked)
I did apply the slightest bit of pressure on all the heatsinks before I put them back. What should I do?
I think it is worth disclosing I bought 2 of these and they are each running on their on 30 amp breaker with their own tripplite PDU. The first one is working fine. So I don't think there is anything wrong with my setup.
1st Card (worked as expected)
Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1244/277, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-10 00:07:24 driver-btm-api.c:630:init_freq_mode: This is scan-user version
2021-08-10 00:07:24 driver-btm-api.c:1979:bitmain_soc_init: opt_multi_version = 1
2021-08-10 00:07:24 driver-btm-api.c:1980:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-10 00:07:24 driver-btm-api.c:1981:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-10 00:07:24 driver-btm-api.c:1982:bitmain_soc_init: Miner compile time: Tue Sep 24 10:03:14 CST 2019 type: Antminer T17
2021-08-10 00:07:24 driver-btm-api.c:1983:bitmain_soc_init: commit version: 1d88fc4 2019-09-23 22:00:06, build by: lol 2019-09-24 10:12:38
2021-08-10 00:07:24 driver-btm-api.c:1800:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-10 00:07:24 driver-btm-api.c:1134:miner_device_init: Detect 256MB control board of XILINX
2021-08-10 00:07:24 driver-btm-api.c:1082:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-10 00:07:24 thread.c:771:create_read_nonce_reg_thread: create thread
2021-08-10 00:07:30 driver-btm-api.c:1066:init_miner_version: miner ID : 8070852a7910481c
2021-08-10 00:07:30 driver-btm-api.c:1072:init_miner_version: FPGA Version = 0xB013
2021-08-10 00:07:31 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-10 00:07:31 eeprom.c:545:eeprom_load: try higher voltage open core
2021-08-10 00:07:31 driver-btm-api.c:704:get_product_id: product_id[0] = 1
2021-08-10 00:07:31 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[0] = 1
2021-08-10 00:07:31 driver-btm-api.c:1864:bitmain_board_init: g_ccdly_opt = 1
2021-08-10 00:07:31 driver-btm-api.c:643:_set_project_type: project:2
2021-08-10 00:07:31 driver-btm-api.c:673:_set_project_type: Project type: Antminer T17
2021-08-10 00:07:31 driver-btm-api.c:684:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-08-10 00:07:31 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-08-10 00:07:36 driver-btm-api.c:1884:bitmain_board_init: Fan check passed.
2021-08-10 00:07:38 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-08-10 00:07:42 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-08-10 00:07:42 thread.c:766:create_pic_heart_beat_thread: create thread
2021-08-10 00:07:42 power_api.c:55:power_init: power init ...
2021-08-10 00:07:42 driver-btm-api.c:1894:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-08-10 00:07:42 power_api.c:46:power_off: init gpio907
2021-08-10 00:08:14 power_api.c:263:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2021-08-10 00:08:15 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:08:17 power_api.c:85:get_average_voltage: chain[0], voltage is: 20.830605
2021-08-10 00:08:17 power_api.c:96:get_average_voltage: aveage voltage is: 20.830605
2021-08-10 00:08:17 power_api.c:109:check_voltage: target_vol = 18.00, actural_vol = 20.83, more than 0.5v diff.
2021-08-10 00:08:18 power_api.c:123:check_voltage_multi: retry time: 1
2021-08-10 00:08:20 power_api.c:85:get_average_voltage: chain[0], voltage is: 19.097783
2021-08-10 00:08:20 power_api.c:96:get_average_voltage: aveage voltage is: 19.097783
2021-08-10 00:08:20 power_api.c:109:check_voltage: target_vol = 18.00, actural_vol = 19.10, more than 0.5v diff.
2021-08-10 00:08:21 power_api.c:123:check_voltage_multi: retry time: 2
2021-08-10 00:08:23 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.805820
2021-08-10 00:08:23 power_api.c:96:get_average_voltage: aveage voltage is: 17.805820
2021-08-10 00:08:23 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 18.000000
2021-08-10 00:08:23 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-10 00:08:23 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-10 00:08:33 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2021-08-10 00:08:34 driver-btm-api.c:347:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0xff
2021-08-10 00:08:34 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2021-08-10 00:08:34 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2021-08-10 00:08:35 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-08-10 00:08:35 driver-btm-api.c:1650:check_clock_counter: freq 50 clock_counter_limit 6
2021-08-10 00:08:35 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-10 00:08:35 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-10 00:08:35 voltage[0] = 1690
2021-08-10 00:08:35 power_api.c:139:set_working_voltage: working_voltage = 16.900000
2021-08-10 00:08:36 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2021-08-10 00:08:36 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2021-08-10 00:08:36 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-08-10 00:08:37 driver-btm-api.c:247:check_bringup_temp: Bring up temperature is 25
2021-08-10 00:08:37 thread.c:786:create_check_miner_status_thread: create thread
2021-08-10 00:08:37 thread.c:776:create_set_miner_status_thread: create thread
2021-08-10 00:08:37 driver-btm-api.c:580:calculate_timeout: dev->timeout = 392
2021-08-10 00:08:37 thread.c:761:create_temperature_monitor_thread: create thread
2021-08-10 00:08:37 freq_tuning.c:150:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-08-10 00:08:37 power_api.c:378:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
2021-08-10 00:08:57 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:08:59 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.811943
2021-08-10 00:08:59 power_api.c:96:get_average_voltage: aveage voltage is: 17.811943
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:611:set_timeout: freq 720 final timeout=163
2021-08-10 00:09:00 power_api.c:396:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2021-08-10 00:09:26 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:09:27 power_api.c:85:get_average_voltage: chain[0], voltage is: 16.930224
2021-08-10 00:09:27 power_api.c:96:get_average_voltage: aveage voltage is: 16.930224
2021-08-10 00:09:27 frequency.c:534:get_current_min_freq: current min freq 720
2021-08-10 00:09:27 driver-btm-api.c:1650:check_clock_counter: freq 720 clock_counter_limit 92
2021-08-10 00:09:28 thread.c:781:create_check_system_status_thread: create thread
2021-08-10 00:09:28 driver-btm-api.c:2098:bitmain_soc_init: Init done!
2021-08-10 00:09:28 driver-btm-api.c:200:set_miner_status: STATUS_INIT
2021-08-10 00:09:32 driver-btm-api.c:200:set_miner_status: STATUS_OKAY
2021-08-10 00:09:38 driver-btm-api.c:1306:dhash_chip_send_job: Verion num 4
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1244/277, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-10 00:07:24 driver-btm-api.c:630:init_freq_mode: This is scan-user version
2021-08-10 00:07:24 driver-btm-api.c:1979:bitmain_soc_init: opt_multi_version = 1
2021-08-10 00:07:24 driver-btm-api.c:1980:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-10 00:07:24 driver-btm-api.c:1981:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-10 00:07:24 driver-btm-api.c:1982:bitmain_soc_init: Miner compile time: Tue Sep 24 10:03:14 CST 2019 type: Antminer T17
2021-08-10 00:07:24 driver-btm-api.c:1983:bitmain_soc_init: commit version: 1d88fc4 2019-09-23 22:00:06, build by: lol 2019-09-24 10:12:38
2021-08-10 00:07:24 driver-btm-api.c:1800:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-10 00:07:24 driver-btm-api.c:1134:miner_device_init: Detect 256MB control board of XILINX
2021-08-10 00:07:24 driver-btm-api.c:1082:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-10 00:07:24 thread.c:771:create_read_nonce_reg_thread: create thread
2021-08-10 00:07:30 driver-btm-api.c:1066:init_miner_version: miner ID : 8070852a7910481c
2021-08-10 00:07:30 driver-btm-api.c:1072:init_miner_version: FPGA Version = 0xB013
2021-08-10 00:07:31 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-10 00:07:31 eeprom.c:545:eeprom_load: try higher voltage open core
2021-08-10 00:07:31 driver-btm-api.c:704:get_product_id: product_id[0] = 1
2021-08-10 00:07:31 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[0] = 1
2021-08-10 00:07:31 driver-btm-api.c:1864:bitmain_board_init: g_ccdly_opt = 1
2021-08-10 00:07:31 driver-btm-api.c:643:_set_project_type: project:2
2021-08-10 00:07:31 driver-btm-api.c:673:_set_project_type: Project type: Antminer T17
2021-08-10 00:07:31 driver-btm-api.c:684:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-08-10 00:07:31 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-08-10 00:07:36 driver-btm-api.c:1884:bitmain_board_init: Fan check passed.
2021-08-10 00:07:38 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-08-10 00:07:42 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-08-10 00:07:42 thread.c:766:create_pic_heart_beat_thread: create thread
2021-08-10 00:07:42 power_api.c:55:power_init: power init ...
2021-08-10 00:07:42 driver-btm-api.c:1894:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-08-10 00:07:42 power_api.c:46:power_off: init gpio907
2021-08-10 00:08:14 power_api.c:263:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2021-08-10 00:08:15 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:08:17 power_api.c:85:get_average_voltage: chain[0], voltage is: 20.830605
2021-08-10 00:08:17 power_api.c:96:get_average_voltage: aveage voltage is: 20.830605
2021-08-10 00:08:17 power_api.c:109:check_voltage: target_vol = 18.00, actural_vol = 20.83, more than 0.5v diff.
2021-08-10 00:08:18 power_api.c:123:check_voltage_multi: retry time: 1
2021-08-10 00:08:20 power_api.c:85:get_average_voltage: chain[0], voltage is: 19.097783
2021-08-10 00:08:20 power_api.c:96:get_average_voltage: aveage voltage is: 19.097783
2021-08-10 00:08:20 power_api.c:109:check_voltage: target_vol = 18.00, actural_vol = 19.10, more than 0.5v diff.
2021-08-10 00:08:21 power_api.c:123:check_voltage_multi: retry time: 2
2021-08-10 00:08:23 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.805820
2021-08-10 00:08:23 power_api.c:96:get_average_voltage: aveage voltage is: 17.805820
2021-08-10 00:08:23 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 18.000000
2021-08-10 00:08:23 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-10 00:08:23 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-10 00:08:33 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2021-08-10 00:08:34 driver-btm-api.c:347:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0xff
2021-08-10 00:08:34 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2021-08-10 00:08:34 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2021-08-10 00:08:35 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-08-10 00:08:35 driver-btm-api.c:1650:check_clock_counter: freq 50 clock_counter_limit 6
2021-08-10 00:08:35 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-10 00:08:35 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-10 00:08:35 voltage[0] = 1690
2021-08-10 00:08:35 power_api.c:139:set_working_voltage: working_voltage = 16.900000
2021-08-10 00:08:36 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2021-08-10 00:08:36 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2021-08-10 00:08:36 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-08-10 00:08:37 driver-btm-api.c:247:check_bringup_temp: Bring up temperature is 25
2021-08-10 00:08:37 thread.c:786:create_check_miner_status_thread: create thread
2021-08-10 00:08:37 thread.c:776:create_set_miner_status_thread: create thread
2021-08-10 00:08:37 driver-btm-api.c:580:calculate_timeout: dev->timeout = 392
2021-08-10 00:08:37 thread.c:761:create_temperature_monitor_thread: create thread
2021-08-10 00:08:37 freq_tuning.c:150:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-08-10 00:08:37 power_api.c:378:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.80 ...
2021-08-10 00:08:57 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:08:59 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.811943
2021-08-10 00:08:59 power_api.c:96:get_average_voltage: aveage voltage is: 17.811943
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-08-10 00:08:59 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-08-10 00:09:00 driver-btm-api.c:611:set_timeout: freq 720 final timeout=163
2021-08-10 00:09:00 power_api.c:396:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2021-08-10 00:09:26 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:09:27 power_api.c:85:get_average_voltage: chain[0], voltage is: 16.930224
2021-08-10 00:09:27 power_api.c:96:get_average_voltage: aveage voltage is: 16.930224
2021-08-10 00:09:27 frequency.c:534:get_current_min_freq: current min freq 720
2021-08-10 00:09:27 driver-btm-api.c:1650:check_clock_counter: freq 720 clock_counter_limit 92
2021-08-10 00:09:28 thread.c:781:create_check_system_status_thread: create thread
2021-08-10 00:09:28 driver-btm-api.c:2098:bitmain_soc_init: Init done!
2021-08-10 00:09:28 driver-btm-api.c:200:set_miner_status: STATUS_INIT
2021-08-10 00:09:32 driver-btm-api.c:200:set_miner_status: STATUS_OKAY
2021-08-10 00:09:38 driver-btm-api.c:1306:dhash_chip_send_job: Verion num 4
2nd card (did not work)
Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1244/277, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-10 00:39:55 driver-btm-api.c:630:init_freq_mode: This is scan-user version
2021-08-10 00:39:55 driver-btm-api.c:1979:bitmain_soc_init: opt_multi_version = 1
2021-08-10 00:39:55 driver-btm-api.c:1980:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-10 00:39:55 driver-btm-api.c:1981:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-10 00:39:55 driver-btm-api.c:1982:bitmain_soc_init: Miner compile time: Tue Sep 24 10:03:14 CST 2019 type: Antminer T17
2021-08-10 00:39:55 driver-btm-api.c:1983:bitmain_soc_init: commit version: 1d88fc4 2019-09-23 22:00:06, build by: lol 2019-09-24 10:12:38
2021-08-10 00:39:55 driver-btm-api.c:1800:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-10 00:39:55 driver-btm-api.c:1134:miner_device_init: Detect 256MB control board of XILINX
2021-08-10 00:39:55 driver-btm-api.c:1082:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-10 00:39:55 thread.c:771:create_read_nonce_reg_thread: create thread
2021-08-10 00:40:01 driver-btm-api.c:1066:init_miner_version: miner ID : 8070852a7910481c
2021-08-10 00:40:01 driver-btm-api.c:1072:init_miner_version: FPGA Version = 0xB013
2021-08-10 00:40:03 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-10 00:40:03 eeprom.c:545:eeprom_load: try higher voltage open core
2021-08-10 00:40:03 driver-btm-api.c:704:get_product_id: product_id[0] = 1
2021-08-10 00:40:03 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[0] = 1
2021-08-10 00:40:03 driver-btm-api.c:1864:bitmain_board_init: g_ccdly_opt = 1
2021-08-10 00:40:03 driver-btm-api.c:643:_set_project_type: project:2
2021-08-10 00:40:03 driver-btm-api.c:673:_set_project_type: Project type: Antminer T17
2021-08-10 00:40:03 driver-btm-api.c:684:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-08-10 00:40:03 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-08-10 00:40:08 driver-btm-api.c:1884:bitmain_board_init: Fan check passed.
2021-08-10 00:40:10 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-08-10 00:40:13 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-08-10 00:40:13 thread.c:766:create_pic_heart_beat_thread: create thread
2021-08-10 00:40:13 power_api.c:55:power_init: power init ...
2021-08-10 00:40:13 driver-btm-api.c:1894:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-08-10 00:40:13 power_api.c:46:power_off: init gpio907
2021-08-10 00:40:45 power_api.c:263:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2021-08-10 00:40:47 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:40:49 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.656924
2021-08-10 00:40:49 power_api.c:96:get_average_voltage: aveage voltage is: 18.656924
2021-08-10 00:40:49 power_api.c:109:check_voltage: target_vol = 18.00, actural_vol = 18.66, more than 0.5v diff.
2021-08-10 00:40:50 power_api.c:123:check_voltage_multi: retry time: 1
2021-08-10 00:40:52 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.044619
2021-08-10 00:40:52 power_api.c:96:get_average_voltage: aveage voltage is: 18.044619
2021-08-10 00:40:52 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 18.000000
2021-08-10 00:40:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-10 00:40:52 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-10 00:41:01 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 0
2021-08-10 00:41:11 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 1
2021-08-10 00:41:21 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 2
2021-08-10 00:41:21 driver-btm-api.c:1036:check_asic_number: Chain 0 only find 0 asic, will power off hash board 0
2021-08-10 00:41:22 driver-btm-api.c:200:set_miner_status: ERROR_SOC_INIT
2021-08-10 00:41:22 driver-btm-api.c:141:stop_mining: stop mining: soc init failed!
2021-08-10 00:41:22 thread.c:816:cancel_read_nonce_reg_thread: cancel thread
2021-08-10 00:41:22 driver-btm-api.c:127:killall_hashboard: ****power off hashboard****
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1244/277, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-10 00:39:55 driver-btm-api.c:630:init_freq_mode: This is scan-user version
2021-08-10 00:39:55 driver-btm-api.c:1979:bitmain_soc_init: opt_multi_version = 1
2021-08-10 00:39:55 driver-btm-api.c:1980:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-10 00:39:55 driver-btm-api.c:1981:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-10 00:39:55 driver-btm-api.c:1982:bitmain_soc_init: Miner compile time: Tue Sep 24 10:03:14 CST 2019 type: Antminer T17
2021-08-10 00:39:55 driver-btm-api.c:1983:bitmain_soc_init: commit version: 1d88fc4 2019-09-23 22:00:06, build by: lol 2019-09-24 10:12:38
2021-08-10 00:39:55 driver-btm-api.c:1800:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-10 00:39:55 driver-btm-api.c:1134:miner_device_init: Detect 256MB control board of XILINX
2021-08-10 00:39:55 driver-btm-api.c:1082:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-10 00:39:55 thread.c:771:create_read_nonce_reg_thread: create thread
2021-08-10 00:40:01 driver-btm-api.c:1066:init_miner_version: miner ID : 8070852a7910481c
2021-08-10 00:40:01 driver-btm-api.c:1072:init_miner_version: FPGA Version = 0xB013
2021-08-10 00:40:03 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-10 00:40:03 eeprom.c:545:eeprom_load: try higher voltage open core
2021-08-10 00:40:03 driver-btm-api.c:704:get_product_id: product_id[0] = 1
2021-08-10 00:40:03 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[0] = 1
2021-08-10 00:40:03 driver-btm-api.c:1864:bitmain_board_init: g_ccdly_opt = 1
2021-08-10 00:40:03 driver-btm-api.c:643:_set_project_type: project:2
2021-08-10 00:40:03 driver-btm-api.c:673:_set_project_type: Project type: Antminer T17
2021-08-10 00:40:03 driver-btm-api.c:684:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-08-10 00:40:03 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-08-10 00:40:08 driver-btm-api.c:1884:bitmain_board_init: Fan check passed.
2021-08-10 00:40:10 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-08-10 00:40:13 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-08-10 00:40:13 thread.c:766:create_pic_heart_beat_thread: create thread
2021-08-10 00:40:13 power_api.c:55:power_init: power init ...
2021-08-10 00:40:13 driver-btm-api.c:1894:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-08-10 00:40:13 power_api.c:46:power_off: init gpio907
2021-08-10 00:40:45 power_api.c:263:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2021-08-10 00:40:47 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-10 00:40:49 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.656924
2021-08-10 00:40:49 power_api.c:96:get_average_voltage: aveage voltage is: 18.656924
2021-08-10 00:40:49 power_api.c:109:check_voltage: target_vol = 18.00, actural_vol = 18.66, more than 0.5v diff.
2021-08-10 00:40:50 power_api.c:123:check_voltage_multi: retry time: 1
2021-08-10 00:40:52 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.044619
2021-08-10 00:40:52 power_api.c:96:get_average_voltage: aveage voltage is: 18.044619
2021-08-10 00:40:52 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 18.000000
2021-08-10 00:40:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-10 00:40:52 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-10 00:41:01 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 0
2021-08-10 00:41:11 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 1
2021-08-10 00:41:21 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 2
2021-08-10 00:41:21 driver-btm-api.c:1036:check_asic_number: Chain 0 only find 0 asic, will power off hash board 0
2021-08-10 00:41:22 driver-btm-api.c:200:set_miner_status: ERROR_SOC_INIT
2021-08-10 00:41:22 driver-btm-api.c:141:stop_mining: stop mining: soc init failed!
2021-08-10 00:41:22 thread.c:816:cancel_read_nonce_reg_thread: cancel thread
2021-08-10 00:41:22 driver-btm-api.c:127:killall_hashboard: ****power off hashboard****
3rd card (Worked)
Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
I live in Ohio.
Check this thread
Quote
I have some experience soldering.
You need a bit more than just that, this is a brief explanation of the things you are going to be doing > https://www.youtube.com/watch?v=5WH7g61d90w&t=89s.
Quote
All the heat sinks seem to be attached pretty well and one of the cards that I believe is one of the defective ones looks like its had all its heat sinks reattached on one side.
It's what's under the heatsinks that matters, the solder that keeps the chip in place goes bad or the chip itself is burned, try to identify chip 25 on your chain 2 and see if you can see any physical damage like solder balls between the chip legs, refer to the image below
Source: https://www.zeusbtc.com/NewsDetails.asp?ID=187
Quote
Is it safe to take the 2 defective cards out and run it with just the 1 while I figure out what I'm doing?
Perfectly fine.
I'd like to suggest you try to test them one by one and maybe the PSU can't provide enough power that is why the one dashboard show 0 ASIC and check the cables swap the cable from chain
Yes, you can run them with only one hashboard.
- to chain [1] (Both power and ribbon cable)let see if there are changes on the logs. If the chain
- shows 0 ASIC and the chain [1] now shows ASIC then there is a possibility that your ribbon cable is defective. So the solution is to replace them.
Is it safe to take the 2 defective cards out and run it with just the 1 while I figure out what I'm doing?
Yes, you can run them with only one hashboard.
Thank you so much for your reply!!!
I live in Ohio. I have some experience soldering.
I've done some console mods like replacing the screen on my gamegear and installing the HDMI mod on my N64 but I have nothing to diagnose these with nor am I really 100% comfortable doing it. Maybe after i've recaptured a bit more of my money i'd try it....
I have opened it up and it looks like one of these cards has been repaired before as there is some unshielded copper wire that looks to be jumping something or something lol.... I'm also pretty sure this is the board that is still working. I did wait a bit to open it up after shutting it down but this card was clearly warmer then the others.
All the heat sinks seem to be attached pretty well and one of the cards that I believe is one of the defective ones looks like its had all its heat sinks reattached on one side.
Is it safe to take the 2 defective cards out and run it with just the 1 while I figure out what I'm doing?
Thanks again!
I live in Ohio. I have some experience soldering.
I've done some console mods like replacing the screen on my gamegear and installing the HDMI mod on my N64 but I have nothing to diagnose these with nor am I really 100% comfortable doing it. Maybe after i've recaptured a bit more of my money i'd try it....
I have opened it up and it looks like one of these cards has been repaired before as there is some unshielded copper wire that looks to be jumping something or something lol.... I'm also pretty sure this is the board that is still working. I did wait a bit to open it up after shutting it down but this card was clearly warmer then the others.
All the heat sinks seem to be attached pretty well and one of the cards that I believe is one of the defective ones looks like its had all its heat sinks reattached on one side.
Is it safe to take the 2 defective cards out and run it with just the 1 while I figure out what I'm doing?
Thanks again!
There you go.
The T17 chips are connected in series if all 30 Asics are not connected the board won't hash, your chain 1 shows 0 Asics which means either the first chip is bad or it has some other issues, chain 2 shows 24 Asics which means the signal is interrupted at chip number 25.
It's very, very, very common for T17 to lose chips this way, the solder bitmain used is of terrible quality, the reported failure rate for these gears was well over 30% in the first a few months, it has now been 2 years and without a doubt, the failure rate has gone up by quite a bit.
The bad news is that these are not easy to fix, you are going to need some tools to confirm which chips need replacement, and then you are going to need to buy the chips from China, and replacing them isn't something everyone can do, if you don't have the tools and skills needed, you will have to send it somewhere to fix it, where are you located?
Quote
2021-08-09 21:54:33 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
2021-08-09 21:54:45 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 0
2021-08-09 21:54:45 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 0
The T17 chips are connected in series if all 30 Asics are not connected the board won't hash, your chain 1 shows 0 Asics which means either the first chip is bad or it has some other issues, chain 2 shows 24 Asics which means the signal is interrupted at chip number 25.
It's very, very, very common for T17 to lose chips this way, the solder bitmain used is of terrible quality, the reported failure rate for these gears was well over 30% in the first a few months, it has now been 2 years and without a doubt, the failure rate has gone up by quite a bit.
The bad news is that these are not easy to fix, you are going to need some tools to confirm which chips need replacement, and then you are going to need to buy the chips from China, and replacing them isn't something everyone can do, if you don't have the tools and skills needed, you will have to send it somewhere to fix it, where are you located?
So I bought this t17 off ebay. Out of the box is was only hashing on 2 of the boards. Now its hashing on just board. I did get a 33% refund from the seller from the 1st board not working. I've posted the log below just looking for a place start.
Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1244/277, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-09 21:52:40 driver-btm-api.c:630:init_freq_mode: This is scan-user version
2021-08-09 21:52:40 driver-btm-api.c:1979:bitmain_soc_init: opt_multi_version = 1
2021-08-09 21:52:40 driver-btm-api.c:1980:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-09 21:52:40 driver-btm-api.c:1981:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-09 21:52:40 driver-btm-api.c:1982:bitmain_soc_init: Miner compile time: Tue Sep 24 10:03:14 CST 2019 type: Antminer T17
2021-08-09 21:52:40 driver-btm-api.c:1983:bitmain_soc_init: commit version: 1d88fc4 2019-09-23 22:00:06, build by: lol 2019-09-24 10:12:38
2021-08-09 21:52:40 driver-btm-api.c:1800:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-09 21:52:40 driver-btm-api.c:1134:miner_device_init: Detect 256MB control board of XILINX
2021-08-09 21:52:40 driver-btm-api.c:1082:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-09 21:52:40 thread.c:771:create_read_nonce_reg_thread: create thread
2021-08-09 21:52:46 driver-btm-api.c:1066:init_miner_version: miner ID : 8070852a7910481c
2021-08-09 21:52:46 driver-btm-api.c:1072:init_miner_version: FPGA Version = 0xB013
2021-08-09 21:52:48 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-09 21:52:49 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-09 21:52:51 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-09 21:52:51 eeprom.c:545:eeprom_load: try higher voltage open core
2021-08-09 21:52:51 driver-btm-api.c:704:get_product_id: product_id[0] = 1
2021-08-09 21:52:51 driver-btm-api.c:704:get_product_id: product_id[1] = 1
2021-08-09 21:52:51 driver-btm-api.c:704:get_product_id: product_id[2] = 1
2021-08-09 21:52:51 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[0] = 1
2021-08-09 21:52:51 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[1] = 1
2021-08-09 21:52:51 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[2] = 1
2021-08-09 21:52:51 driver-btm-api.c:1864:bitmain_board_init: g_ccdly_opt = 1
2021-08-09 21:52:51 driver-btm-api.c:643:_set_project_type: project:2
2021-08-09 21:52:51 driver-btm-api.c:673:_set_project_type: Project type: Antminer T17
2021-08-09 21:52:51 driver-btm-api.c:684:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:684:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:684:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-08-09 21:52:53 driver-btm-api.c:1884:bitmain_board_init: Fan check passed.
2021-08-09 21:52:55 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-08-09 21:52:59 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-08-09 21:53:00 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-08-09 21:53:04 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2021-08-09 21:53:06 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-08-09 21:53:09 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2021-08-09 21:53:09 thread.c:766:create_pic_heart_beat_thread: create thread
2021-08-09 21:53:09 power_api.c:55:power_init: power init ...
2021-08-09 21:53:09 driver-btm-api.c:1894:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-08-09 21:53:09 power_api.c:46:power_off: init gpio907
2021-08-09 21:53:41 power_api.c:263:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2021-08-09 21:53:47 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-09 21:53:48 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.062988
2021-08-09 21:53:50 power_api.c:85:get_average_voltage: chain[1], voltage is: 18.069111
2021-08-09 21:53:52 power_api.c:85:get_average_voltage: chain[2], voltage is: 18.136465
2021-08-09 21:53:52 power_api.c:96:get_average_voltage: aveage voltage is: 18.089521
2021-08-09 21:53:52 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 18.000000
2021-08-09 21:53:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-09 21:53:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2021-08-09 21:53:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2021-08-09 21:53:52 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-09 21:54:03 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2021-08-09 21:54:13 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2021-08-09 21:54:23 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2021-08-09 21:54:33 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
2021-08-09 21:54:33 driver-btm-api.c:1036:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
2021-08-09 21:54:45 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 0
2021-08-09 21:54:55 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 1
2021-08-09 21:55:05 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 2
2021-08-09 21:55:05 driver-btm-api.c:1036:check_asic_number: Chain 2 only find 24 asic, will power off hash board 2
2021-08-09 21:55:08 driver-btm-api.c:347:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0xff
2021-08-09 21:55:08 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2021-08-09 21:55:08 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2021-08-09 21:55:09 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-08-09 21:55:09 driver-btm-api.c:1650:check_clock_counter: freq 50 clock_counter_limit 6
2021-08-09 21:55:09 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-09 21:55:09 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-09 21:55:09 voltage[0] = 1690
2021-08-09 21:55:09 power_api.c:139:set_working_voltage: working_voltage = 16.900000
2021-08-09 21:55:10 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2021-08-09 21:55:10 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2021-08-09 21:55:10 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-08-09 21:55:11 driver-btm-api.c:247:check_bringup_temp: Bring up temperature is 28
2021-08-09 21:55:11 thread.c:786:create_check_miner_status_thread: create thread
2021-08-09 21:55:11 thread.c:776:create_set_miner_status_thread: create thread
2021-08-09 21:55:11 driver-btm-api.c:580:calculate_timeout: dev->timeout = 392
2021-08-09 21:55:11 thread.c:761:create_temperature_monitor_thread: create thread
2021-08-09 21:55:11 freq_tuning.c:150:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-08-09 21:55:11 power_api.c:378:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.60 ...
2021-08-09 21:55:34 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-09 21:55:35 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.640498
2021-08-09 21:55:35 power_api.c:96:get_average_voltage: aveage voltage is: 17.640498
2021-08-09 21:55:35 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-08-09 21:55:35 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-08-09 21:55:37 driver-btm-api.c:611:set_timeout: freq 720 final timeout=163
2021-08-09 21:55:37 power_api.c:396:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2021-08-09 21:56:00 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-09 21:56:03 power_api.c:85:get_average_voltage: chain[0], voltage is: 16.954717
2021-08-09 21:56:03 power_api.c:96:get_average_voltage: aveage voltage is: 16.954717
2021-08-09 21:56:03 frequency.c:534:get_current_min_freq: current min freq 720
2021-08-09 21:56:03 driver-btm-api.c:1650:check_clock_counter: freq 720 clock_counter_limit 92
2021-08-09 21:56:03 thread.c:781:create_check_system_status_thread: create thread
2021-08-09 21:56:04 driver-btm-api.c:2098:bitmain_soc_init: Init done!
2021-08-09 21:56:04 driver-btm-api.c:200:set_miner_status: STATUS_INIT
2021-08-09 21:56:08 driver-btm-api.c:200:set_miner_status: STATUS_OKAY
2021-08-09 21:56:13 driver-btm-api.c:1306:dhash_chip_send_job: Verion num 4
2021-08-09 22:01:12 thread.c:404:is_zero_nonce_happened: chain_nonce[0] = 15252
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203668K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25708K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12668K (ccea2000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1244/277, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-09 21:52:40 driver-btm-api.c:630:init_freq_mode: This is scan-user version
2021-08-09 21:52:40 driver-btm-api.c:1979:bitmain_soc_init: opt_multi_version = 1
2021-08-09 21:52:40 driver-btm-api.c:1980:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-09 21:52:40 driver-btm-api.c:1981:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-09 21:52:40 driver-btm-api.c:1982:bitmain_soc_init: Miner compile time: Tue Sep 24 10:03:14 CST 2019 type: Antminer T17
2021-08-09 21:52:40 driver-btm-api.c:1983:bitmain_soc_init: commit version: 1d88fc4 2019-09-23 22:00:06, build by: lol 2019-09-24 10:12:38
2021-08-09 21:52:40 driver-btm-api.c:1800:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-09 21:52:40 driver-btm-api.c:1134:miner_device_init: Detect 256MB control board of XILINX
2021-08-09 21:52:40 driver-btm-api.c:1082:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-09 21:52:40 thread.c:771:create_read_nonce_reg_thread: create thread
2021-08-09 21:52:46 driver-btm-api.c:1066:init_miner_version: miner ID : 8070852a7910481c
2021-08-09 21:52:46 driver-btm-api.c:1072:init_miner_version: FPGA Version = 0xB013
2021-08-09 21:52:48 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-09 21:52:49 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-09 21:52:51 eeprom.c:456:check_pattern_test_level: L6 board
2021-08-09 21:52:51 eeprom.c:545:eeprom_load: try higher voltage open core
2021-08-09 21:52:51 driver-btm-api.c:704:get_product_id: product_id[0] = 1
2021-08-09 21:52:51 driver-btm-api.c:704:get_product_id: product_id[1] = 1
2021-08-09 21:52:51 driver-btm-api.c:704:get_product_id: product_id[2] = 1
2021-08-09 21:52:51 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[0] = 1
2021-08-09 21:52:51 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[1] = 1
2021-08-09 21:52:51 driver-btm-api.c:1623:get_ccdly_opt: ccdly_opt[2] = 1
2021-08-09 21:52:51 driver-btm-api.c:1864:bitmain_board_init: g_ccdly_opt = 1
2021-08-09 21:52:51 driver-btm-api.c:643:_set_project_type: project:2
2021-08-09 21:52:51 driver-btm-api.c:673:_set_project_type: Project type: Antminer T17
2021-08-09 21:52:51 driver-btm-api.c:684:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:684:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:684:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-08-09 21:52:51 driver-btm-api.c:685:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-08-09 21:52:53 driver-btm-api.c:1884:bitmain_board_init: Fan check passed.
2021-08-09 21:52:55 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-08-09 21:52:59 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-08-09 21:53:00 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-08-09 21:53:04 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2021-08-09 21:53:06 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-08-09 21:53:09 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2021-08-09 21:53:09 thread.c:766:create_pic_heart_beat_thread: create thread
2021-08-09 21:53:09 power_api.c:55:power_init: power init ...
2021-08-09 21:53:09 driver-btm-api.c:1894:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-08-09 21:53:09 power_api.c:46:power_off: init gpio907
2021-08-09 21:53:41 power_api.c:263:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2021-08-09 21:53:47 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-09 21:53:48 power_api.c:85:get_average_voltage: chain[0], voltage is: 18.062988
2021-08-09 21:53:50 power_api.c:85:get_average_voltage: chain[1], voltage is: 18.069111
2021-08-09 21:53:52 power_api.c:85:get_average_voltage: chain[2], voltage is: 18.136465
2021-08-09 21:53:52 power_api.c:96:get_average_voltage: aveage voltage is: 18.089521
2021-08-09 21:53:52 power_api.c:181:set_iic_power_by_voltage: now set voltage to : 18.000000
2021-08-09 21:53:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-09 21:53:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2021-08-09 21:53:52 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2021-08-09 21:53:52 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-09 21:54:03 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2021-08-09 21:54:13 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2021-08-09 21:54:23 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2021-08-09 21:54:33 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
2021-08-09 21:54:33 driver-btm-api.c:1036:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
2021-08-09 21:54:45 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 0
2021-08-09 21:54:55 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 1
2021-08-09 21:55:05 driver-btm-api.c:1009:check_asic_number_with_power_on: Chain[2]: find 24 asic, times 2
2021-08-09 21:55:05 driver-btm-api.c:1036:check_asic_number: Chain 2 only find 24 asic, will power off hash board 2
2021-08-09 21:55:08 driver-btm-api.c:347:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0xff
2021-08-09 21:55:08 driver-hash-chip.c:490:set_clock_delay_control: core_data = 0xb4
2021-08-09 21:55:08 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2021-08-09 21:55:09 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-08-09 21:55:09 driver-btm-api.c:1650:check_clock_counter: freq 50 clock_counter_limit 6
2021-08-09 21:55:09 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2021-08-09 21:55:09 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-08-09 21:55:09 voltage[0] = 1690
2021-08-09 21:55:09 power_api.c:139:set_working_voltage: working_voltage = 16.900000
2021-08-09 21:55:10 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2021-08-09 21:55:10 driver-hash-chip.c:233:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2021-08-09 21:55:10 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-08-09 21:55:11 driver-btm-api.c:247:check_bringup_temp: Bring up temperature is 28
2021-08-09 21:55:11 thread.c:786:create_check_miner_status_thread: create thread
2021-08-09 21:55:11 thread.c:776:create_set_miner_status_thread: create thread
2021-08-09 21:55:11 driver-btm-api.c:580:calculate_timeout: dev->timeout = 392
2021-08-09 21:55:11 thread.c:761:create_temperature_monitor_thread: create thread
2021-08-09 21:55:11 freq_tuning.c:150:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-08-09 21:55:11 power_api.c:378:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.60 ...
2021-08-09 21:55:34 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-09 21:55:35 power_api.c:85:get_average_voltage: chain[0], voltage is: 17.640498
2021-08-09 21:55:35 power_api.c:96:get_average_voltage: aveage voltage is: 17.640498
2021-08-09 21:55:35 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 44 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 7, usr divider: 1
2021-08-09 21:55:35 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 51 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 6, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 61 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 5, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 77 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 4, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 102 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 3, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 154 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 2, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 308 set refdiv: 2, fbdiv: 173, postdiv1: 7, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 360 set refdiv: 2, fbdiv: 173, postdiv1: 6, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 432 set refdiv: 2, fbdiv: 173, postdiv1: 5, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 540 set refdiv: 2, fbdiv: 173, postdiv1: 4, postdiv2: 1, usr divider: 1
2021-08-09 21:55:36 driver-btm-api.c:448:change_freq_one_chain: chain[0] freq: 720 set refdiv: 2, fbdiv: 173, postdiv1: 3, postdiv2: 1, usr divider: 1
2021-08-09 21:55:37 driver-btm-api.c:611:set_timeout: freq 720 final timeout=163
2021-08-09 21:55:37 power_api.c:396:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2021-08-09 21:56:00 power_api.c:123:check_voltage_multi: retry time: 0
2021-08-09 21:56:03 power_api.c:85:get_average_voltage: chain[0], voltage is: 16.954717
2021-08-09 21:56:03 power_api.c:96:get_average_voltage: aveage voltage is: 16.954717
2021-08-09 21:56:03 frequency.c:534:get_current_min_freq: current min freq 720
2021-08-09 21:56:03 driver-btm-api.c:1650:check_clock_counter: freq 720 clock_counter_limit 92
2021-08-09 21:56:03 thread.c:781:create_check_system_status_thread: create thread
2021-08-09 21:56:04 driver-btm-api.c:2098:bitmain_soc_init: Init done!
2021-08-09 21:56:04 driver-btm-api.c:200:set_miner_status: STATUS_INIT
2021-08-09 21:56:08 driver-btm-api.c:200:set_miner_status: STATUS_OKAY
2021-08-09 21:56:13 driver-btm-api.c:1306:dhash_chip_send_job: Verion num 4
2021-08-09 22:01:12 thread.c:404:is_zero_nonce_happened: chain_nonce[0] = 15252
Jump to: