Author

Topic: T17+ works perfectly but after a while one of hash board get down (Read 362 times)

legendary
Activity: 2170
Merit: 6279
be constructive or S.T.F.U
I have the same issue with my S9 and it seems that it can be fixed if I reboot the device. It seems to me that it is an software issue but I can't really clarify it. Did you find a solution for your issues?

To save you time and effort, your issue and OP's issues are completely unrelated, the 17 series have a known issue with the chip to PCB soldering, your issue is different, use the multi-option firmware by Bitmain and drop the hashrate by 2th, this will likely fix the issue for you, it seems like the bad board (probably 1 or 2 chips on it) can't deal with the default frequency.

If the issue isn't solved, you are going to need to use firmware that allows you to tune each chip individually, either Vnish or BO+, the tunning will lower the frequency on the bad chips and it will hopefully get it to a stable state where rebooting is no longer needed.
legendary
Activity: 3206
Merit: 2904
Block halving is coming.
I have the same issue with my S9 and it seems that it can be fixed if I reboot the device. It seems to me that it is an software issue but I can't really clarify it. Did you find a solution for your issues?

If you feel that it's a software issue why not start to flash the unit and flash the hashboard with Pickit3? It should give you a bit of clarification without not doing it.
if it works after flashing then it's a software issue but if not it's related to a hardware issue.
hero member
Activity: 924
Merit: 642
Magic
I have the same issue with my S9 and it seems that it can be fixed if I reboot the device. It seems to me that it is an software issue but I can't really clarify it. Did you find a solution for your issues?
legendary
Activity: 3206
Merit: 2904
Block halving is coming.
It's a common issue on Antminer 17 series if you bought this new usually the issue is related to the temp sensor replacing it might solve the issue.

But before you touch those parts you need to try some suggestions from this link below. It could be just related to a software issue so flashing it might work.

- https://bitcointalksearch.org/topic/antminer-t17s17-temp-sensor-problem-discussion-5244120

If it didn't work then your last hope is to replace the temp sensor.
jr. member
Activity: 46
Merit: 14
The log shows that some chips are missing after running for a while, I wonder if your T17+ is new?

Because this situation may be caused by chip aging or excessive temperature.
newbie
Activity: 3
Merit: 1
Hi guys,

I have a T17+ 58th, that works good for a while, after that one of hash board not working
Then after reboot it works again

There is my Kernel Log:
Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203416K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25960K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12920K (cce62000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002420000
nand_read_bbt: bad block at 0x000002440000
nand_read_bbt: bad block at 0x000002460000
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 22/9, WL threshold: 4096, image sequence number: 4094950973
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID AB4DF95D-52A4-419D-B203-FC91BE96E568, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 609/151, WL threshold: 4096, image sequence number: 897013664
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 677AE791-6FAE-4607-ADCA-D4F602F30476, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-06-29 13:33:20 driver-btm-api.c:762:init_freq_mode: This is scan-user version
2021-06-29 13:33:20 driver-btm-api.c:2553:bitmain_soc_init: opt_multi_version     = 1
2021-06-29 13:33:20 driver-btm-api.c:2554:bitmain_soc_init: opt_bitmain_ab        = 1
2021-06-29 13:33:20 driver-btm-api.c:2555:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-06-29 13:33:20 driver-btm-api.c:2556:bitmain_soc_init: Miner compile time: Tue Jun  2 10:11:10 CST 2020 type: Antminer T17+
2021-06-29 13:33:20 driver-btm-api.c:2557:bitmain_soc_init: commit version: 9e9a5bf 2020-06-01 18:48:14, build by: lol 2020-06-02 10:21:50
2021-06-29 13:33:20 driver-btm-api.c:2180:show_sn: 817484042b104814�7
2021-06-29 13:33:20 driver-btm-api.c:2237:handle_sn_for_factory_mode: read sn success, 817484042b104814�7
2021-06-29 13:33:20 fan.c:263:front_fan_power_on: Note: front fan is power on!
2021-06-29 13:33:20 fan.c:273:rear_fan_power_on: Note: rear fan is power on!
2021-06-29 13:33:20 driver-btm-api.c:1357:miner_device_init: Detect 256MB control board of XILINX
2021-06-29 13:33:20 driver-btm-api.c:1298:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-06-29 13:33:26 driver-btm-api.c:1281:init_miner_version: miner ID : 817484042b104814
2021-06-29 13:33:26 driver-btm-api.c:1287:init_miner_version: FPGA Version = 0xB023
2021-06-29 13:33:31 driver-btm-api.c:814:get_product_id: product_id[0] = 0
2021-06-29 13:33:31 driver-btm-api.c:814:get_product_id: product_id[2] = 0
2021-06-29 13:33:31 driver-btm-api.c:814:get_product_id: product_id[3] = 0
2021-06-29 13:33:31 driver-btm-api.c:845:get_chip_version: chip_version[0] = 1
2021-06-29 13:33:31 driver-btm-api.c:845:get_chip_version: chip_version[2] = 1
2021-06-29 13:33:31 driver-btm-api.c:845:get_chip_version: chip_version[3] = 1
2021-06-29 13:33:31 driver-btm-api.c:2293:update_conf_by_power_feedback: Power feedback is disabled
2021-06-29 13:33:31 driver-btm-api.c:2297:update_conf_by_power_feedback: get_calibration_voltage, vol:1850.
2021-06-29 13:33:31 frequency.c:1389:adjust_higer_max_vol_table: adjust_higer_max_vol_table, ideal_hashrate = 59935, index = 3, adjust_vol = 30
2021-06-29 13:33:31 thread.c:1462:create_read_nonce_reg_thread: create thread
2021-06-29 13:33:37 driver-btm-api.c:1281:init_miner_version: miner ID : 817484042b104814
2021-06-29 13:33:37 driver-btm-api.c:1287:init_miner_version: FPGA Version = 0xB023
2021-06-29 13:33:43 driver-btm-api.c:814:get_product_id: product_id[0] = 0
2021-06-29 13:33:43 driver-btm-api.c:814:get_product_id: product_id[2] = 0
2021-06-29 13:33:43 driver-btm-api.c:814:get_product_id: product_id[3] = 0
2021-06-29 13:33:43 driver-btm-api.c:845:get_chip_version: chip_version[0] = 1
2021-06-29 13:33:43 driver-btm-api.c:845:get_chip_version: chip_version[2] = 1
2021-06-29 13:33:43 driver-btm-api.c:845:get_chip_version: chip_version[3] = 1
2021-06-29 13:33:43 driver-btm-api.c:1944:get_ccdly_opt: ccdly_opt[0] = 0
2021-06-29 13:33:43 driver-btm-api.c:1944:get_ccdly_opt: ccdly_opt[2] = 0
2021-06-29 13:33:43 driver-btm-api.c:1944:get_ccdly_opt: ccdly_opt[3] = 0
2021-06-29 13:33:43 driver-btm-api.c:2439:bitmain_board_init: g_ccdly_opt = 0
2021-06-29 13:33:43 driver-btm-api.c:775:_set_project_type: project:0, set to T17Plus always
2021-06-29 13:33:43 driver-btm-api.c:790:_set_project_type: Project type: Antminer T17+
2021-06-29 13:33:43 driver-btm-api.c:801:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-06-29 13:33:43 driver-btm-api.c:802:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-06-29 13:33:43 driver-btm-api.c:801:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-06-29 13:33:43 driver-btm-api.c:802:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-06-29 13:33:43 driver-btm-api.c:801:dump_pcb_bom_version: Chain [3] PCB Version: 0x0100
2021-06-29 13:33:43 driver-btm-api.c:802:dump_pcb_bom_version: Chain [3] BOM Version: 0x0100
2021-06-29 13:33:44 driver-btm-api.c:2461:bitmain_board_init: Fan check passed.
2021-06-29 13:33:45 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-06-29 13:33:47 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-06-29 13:33:48 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-06-29 13:33:50 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-06-29 13:33:51 board.c:36:jump_and_app_check_restore_pic: chain[3] PIC jump to app
2021-06-29 13:33:53 board.c:40:jump_and_app_check_restore_pic: Check chain[3] PIC fw version=0x88
2021-06-29 13:33:53 thread.c:1457:create_pic_heart_beat_thread: create thread
2021-06-29 13:33:54 power_api.c:231:power_init: power type version: 0x0042
2021-06-29 13:33:54 power_api.c:249:power_init: Power init:
2021-06-29 13:33:54 power_api.c:250:power_init: current_voltage_raw = 0
2021-06-29 13:33:54 power_api.c:251:power_init: highest_voltage_raw = 1950
2021-06-29 13:33:54 power_api.c:252:power_init: working_voltage_raw = 1900
2021-06-29 13:33:54 power_api.c:253:power_init: higher_voltage_raw  = 1930
2021-06-29 13:33:54 power_api.c:254:power_init: check_asic_voltage_raw  = 2000
2021-06-29 13:33:54 driver-btm-api.c:2471:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-06-29 13:33:54 power_api.c:218:power_off: init gpio907
2021-06-29 13:33:54 power_api.c:221:power_off: set gpio907 to 1
2021-06-29 13:34:25 power_api.c:206:power_on: set gpio907 to 0
2021-06-29 13:34:26 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1850, step by step.
2021-06-29 13:34:45 power_api.c:120:check_voltage_multi: retry time: 0
2021-06-29 13:34:46 power_api.c:56:_get_avg_voltage: an6 raw = 2.496774, factor = 0.998710
2021-06-29 13:34:46 power_api.c:60:_get_avg_voltage: chain 0, an0 = 0.515504, an2 18.607235, an6 2.500000.
2021-06-29 13:34:47 power_api.c:56:_get_avg_voltage: an6 raw = 2.493548, factor = 0.997419
2021-06-29 13:34:47 power_api.c:60:_get_avg_voltage: chain 2, an0 = 0.639069, an2 18.680466, an6 2.500000.
2021-06-29 13:34:48 power_api.c:56:_get_avg_voltage: an6 raw = 2.496774, factor = 0.998710
2021-06-29 13:34:48 power_api.c:60:_get_avg_voltage: chain 3, an0 = 0.564599, an2 18.607235, an6 2.500000.
2021-06-29 13:34:48 power_api.c:85:_get_avg_voltage: average_voltage = 18.631645
2021-06-29 13:34:48 power_api.c:106:check_voltage: target_vol = 18.50, actural_vol = 18.63, check voltage passed.
2021-06-29 13:34:50 power_api.c:56:_get_avg_voltage: an6 raw = 2.496774, factor = 0.998710
2021-06-29 13:34:50 power_api.c:60:_get_avg_voltage: chain 0, an0 = 0.515504, an2 18.607235, an6 2.500000.
2021-06-29 13:34:51 power_api.c:56:_get_avg_voltage: an6 raw = 2.496774, factor = 0.998710
2021-06-29 13:34:51 power_api.c:60:_get_avg_voltage: chain 2, an0 = 0.638243, an2 18.656331, an6 2.500000.
2021-06-29 13:34:52 power_api.c:56:_get_avg_voltage: an6 raw = 2.493548, factor = 0.997419
2021-06-29 13:34:52 power_api.c:60:_get_avg_voltage: chain 3, an0 = 0.565330, an2 18.631307, an6 2.500000.
2021-06-29 13:34:52 power_api.c:85:_get_avg_voltage: average_voltage = 18.631624
2021-06-29 13:34:52 power_api.c:106:check_voltage: target_vol = 18.50, actural_vol = 18.63, check voltage passed.
2021-06-29 13:34:52 uart.c:81:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-06-29 13:35:01 driver-btm-api.c:1162:check_asic_number_with_power_on: Chain[0]: find 44 asic, times 0
2021-06-29 13:35:10 driver-btm-api.c:1162:check_asic_number_with_power_on: Chain[2]: find 44 asic, times 0
2021-06-29 13:35:19 driver-btm-api.c:1162:check_asic_number_with_power_on: Chain[3]: find 44 asic, times 0
2021-06-29 13:35:24 driver-btm-api.c:425:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2021-06-29 13:35:25 driver-btm-api.c:425:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2021-06-29 13:35:25 driver-btm-api.c:425:set_order_clock: chain[3]: set order clock, stragegy 3 clock_en=0x1
2021-06-29 13:35:25 driver-btm-api.c:1931:get_core_clock_delay_setting: PWTH_SEL 3, CCDLY_SEL 0
2021-06-29 13:35:25 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2021-06-29 13:35:25 driver-btm-api.c:1972:check_clock_counter: freq 50 clock_counter_limit 6
2021-06-29 13:35:47 voltage[0] = 1850
2021-06-29 13:35:47 voltage[2] = 1850
2021-06-29 13:35:47 voltage[3] = 1850
2021-06-29 13:35:47 power_api.c:262:set_working_voltage_raw: working_voltage_raw = 1850
2021-06-29 13:35:48 temperature.c:313:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success. NCT218
2021-06-29 13:35:50 temperature.c:313:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success. NCT218
2021-06-29 13:35:51 temperature.c:313:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 3 success. NCT218
2021-06-29 13:35:51 uart.c:81:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-06-29 13:35:52 driver-btm-api.c:294:check_bringup_temp: Bring up temperature is 29
2021-06-29 13:35:52 thread.c:1477:create_check_miner_status_thread: create thread
2021-06-29 13:35:52 thread.c:1467:create_set_miner_status_thread: create thread
2021-06-29 13:35:52 driver-btm-api.c:712:calculate_timeout: dev->timeout = 245
2021-06-29 13:35:52 thread.c:1447:create_temperature_monitor_thread: create thread
2021-06-29 13:35:52 frequency.c:527:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 29 dec_freq_index=0
2021-06-29 13:35:52 freq_tuning.c:184:freq_tuning_get_max_freq: Max freq of tuning is 790
2021-06-29 13:35:52 driver-btm-api.c:1802:send_null_work: [DEBUG] Send null work.
2021-06-29 13:35:52 thread.c:1437:create_asic_status_monitor_thread: create thread
2021-06-29 13:35:52 frequency.c:1194:inc_freq_with_fixed_vco: chain = 255, freq = 660, is_higher_voltage = true
2021-06-29 13:35:52 frequency.c:1210:inc_freq_with_fixed_vco: [0] _POSTDIV1 = 7, _POSTDIV2 = 7, USER_DIV = 1, freq = 53
2021-06-29 13:35:54 frequency.c:1210:inc_freq_with_fixed_vco: [1] _POSTDIV1 = 7, _POSTDIV2 = 6, USER_DIV = 1, freq = 62
2021-06-29 13:35:56 frequency.c:1210:inc_freq_with_fixed_vco: [2] _POSTDIV1 = 6, _POSTDIV2 = 6, USER_DIV = 1, freq = 73
2021-06-29 13:35:58 frequency.c:1210:inc_freq_with_fixed_vco: [3] _POSTDIV1 = 7, _POSTDIV2 = 5, USER_DIV = 1, freq = 75
2021-06-29 13:36:00 frequency.c:1210:inc_freq_with_fixed_vco: [4] _POSTDIV1 = 6, _POSTDIV2 = 5, USER_DIV = 1, freq = 87
2021-06-29 13:36:02 frequency.c:1210:inc_freq_with_fixed_vco: [5] _POSTDIV1 = 7, _POSTDIV2 = 4, USER_DIV = 1, freq = 94
2021-06-29 13:36:04 frequency.c:1210:inc_freq_with_fixed_vco: [6] _POSTDIV1 = 5, _POSTDIV2 = 5, USER_DIV = 1, freq = 105
2021-06-29 13:36:09 frequency.c:1210:inc_freq_with_fixed_vco: [7] _POSTDIV1 = 6, _POSTDIV2 = 4, USER_DIV = 1, freq = 109
2021-06-29 13:36:14 frequency.c:1210:inc_freq_with_fixed_vco: [8] _POSTDIV1 = 7, _POSTDIV2 = 3, USER_DIV = 1, freq = 125
2021-06-29 13:36:18 frequency.c:1210:inc_freq_with_fixed_vco: [9] _POSTDIV1 = 5, _POSTDIV2 = 4, USER_DIV = 1, freq = 131
2021-06-29 13:36:23 frequency.c:1210:inc_freq_with_fixed_vco: [10] _POSTDIV1 = 6, _POSTDIV2 = 3, USER_DIV = 1, freq = 146
2021-06-29 13:36:27 frequency.c:1210:inc_freq_with_fixed_vco: [11] _POSTDIV1 = 4, _POSTDIV2 = 4, USER_DIV = 1, freq = 164
2021-06-29 13:36:35 frequency.c:1210:inc_freq_with_fixed_vco: [12] _POSTDIV1 = 5, _POSTDIV2 = 3, USER_DIV = 1, freq = 175
2021-06-29 13:36:43 frequency.c:1210:inc_freq_with_fixed_vco: [13] _POSTDIV1 = 7, _POSTDIV2 = 2, USER_DIV = 1, freq = 188
2021-06-29 13:36:51 frequency.c:1210:inc_freq_with_fixed_vco: [14] _POSTDIV1 = 4, _POSTDIV2 = 3, USER_DIV = 1, freq = 219
2021-06-29 13:37:04 frequency.c:1210:inc_freq_with_fixed_vco: [15] _POSTDIV1 = 6, _POSTDIV2 = 2, USER_DIV = 1, freq = 219
2021-06-29 13:37:16 frequency.c:1210:inc_freq_with_fixed_vco: [16] _POSTDIV1 = 5, _POSTDIV2 = 2, USER_DIV = 1, freq = 263
2021-06-29 13:37:34 frequency.c:1210:inc_freq_with_fixed_vco: [17] _POSTDIV1 = 4, _POSTDIV2 = 2, USER_DIV = 1, freq = 329
2021-06-29 13:37:59 frequency.c:1210:inc_freq_with_fixed_vco: [18] _POSTDIV1 = 7, _POSTDIV2 = 1, USER_DIV = 1, freq = 376
2021-06-29 13:38:31 frequency.c:1210:inc_freq_with_fixed_vco: [19] _POSTDIV1 = 6, _POSTDIV2 = 1, USER_DIV = 1, freq = 439
2021-06-29 13:39:11 frequency.c:1210:inc_freq_with_fixed_vco: [20] _POSTDIV1 = 5, _POSTDIV2 = 1, USER_DIV = 1, freq = 527
2021-06-29 13:41:12 frequency.c:1210:inc_freq_with_fixed_vco: [21] _POSTDIV1 = 4, _POSTDIV2 = 1, USER_DIV = 1, freq = 659
2021-06-29 13:41:12 power_api.c:388:set_to_voltage_by_steps: Set to voltage raw 1820, step by step.
2021-06-29 13:41:30 power_api.c:120:check_voltage_multi: retry time: 0
2021-06-29 13:41:32 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:41:32 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.215484, an2 18.215484, an6 2.500000.
2021-06-29 13:41:33 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:41:33 power_api.c:60:_get_avg_voltage: chain 2, an0 = 18.117419, an2 18.240000, an6 2.500000.
2021-06-29 13:41:34 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:41:34 power_api.c:60:_get_avg_voltage: chain 3, an0 = 18.190968, an2 18.190968, an6 2.500000.
2021-06-29 13:41:34 power_api.c:85:_get_avg_voltage: average_voltage = 18.215484
2021-06-29 13:41:34 power_api.c:106:check_voltage: target_vol = 18.20, actural_vol = 18.22, check voltage passed.
2021-06-29 13:41:36 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:41:36 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.215484, an2 18.190968, an6 2.500000.
2021-06-29 13:41:37 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:41:37 power_api.c:60:_get_avg_voltage: chain 2, an0 = 18.141935, an2 18.264516, an6 2.500000.
2021-06-29 13:41:39 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:41:39 power_api.c:60:_get_avg_voltage: chain 3, an0 = 18.190968, an2 18.190968, an6 2.500000.
2021-06-29 13:41:39 power_api.c:85:_get_avg_voltage: average_voltage = 18.215484
2021-06-29 13:41:39 power_api.c:106:check_voltage: target_vol = 18.20, actural_vol = 18.22, check voltage passed.
2021-06-29 13:46:33 frequency.c:1231:inc_freq_with_fixed_step: chain = 0, freq_start = 660, freq_end = 670, freq_step = 5, is_higher_voltage = true
2021-06-29 13:46:33 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 665 clock_counter_limit 20
2021-06-29 13:46:35 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 670 clock_counter_limit 20
2021-06-29 13:46:37 frequency.c:1231:inc_freq_with_fixed_step: chain = 2, freq_start = 660, freq_end = 670, freq_step = 5, is_higher_voltage = true
2021-06-29 13:46:37 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 665 clock_counter_limit 20
2021-06-29 13:46:38 driver-btm-api.c:2020:check_clock_counter_domain_last_core: freq 670 clock_counter_limit 20
2021-06-29 13:46:38 register.c:1371:quick_dump_core_hash_clock_counter: bad clock counter. chain = 2, asic = 1, core = 503, found 1, clock counter 0x00FB000D
2021-06-29 13:46:40 frequency.c:1231:inc_freq_with_fixed_step: chain = 0, freq_start = 670, freq_end = 670, freq_step = 5, is_higher_voltage = true
2021-06-29 13:46:40 frequency.c:1231:inc_freq_with_fixed_step: chain = 2, freq_start = 670, freq_end = 670, freq_step = 5, is_higher_voltage = true
2021-06-29 13:46:40 frequency.c:1058:inc_asic_diff_freq_by_steps: chain = 0, start = 670, freq_step = 5
2021-06-29 13:46:41 frequency.c:1058:inc_asic_diff_freq_by_steps: chain = 2, start = 670, freq_step = 5
2021-06-29 13:46:43 frequency.c:1058:inc_asic_diff_freq_by_steps: chain = 3, start = 660, freq_step = 5
2021-06-29 13:46:46 driver-btm-api.c:743:set_timeout: freq 690 final timeout=106
2021-06-29 13:46:46 power_api.c:346:set_to_working_voltage_by_steps: Set to voltage raw 1850, step by step.
2021-06-29 13:47:04 power_api.c:120:check_voltage_multi: retry time: 0
2021-06-29 13:47:05 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:47:05 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.485161, an2 18.485161, an6 2.500000.
2021-06-29 13:47:06 power_api.c:56:_get_avg_voltage: an6 raw = 2.503226, factor = 1.001290
2021-06-29 13:47:06 power_api.c:60:_get_avg_voltage: chain 2, an0 = 18.387888, an2 18.534795, an6 2.500000.
2021-06-29 13:47:07 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:47:07 power_api.c:60:_get_avg_voltage: chain 3, an0 = 18.485161, an2 18.485161, an6 2.500000.
2021-06-29 13:47:07 power_api.c:85:_get_avg_voltage: average_voltage = 18.501706
2021-06-29 13:47:07 power_api.c:106:check_voltage: target_vol = 18.50, actural_vol = 18.50, check voltage passed.
2021-06-29 13:47:10 power_api.c:56:_get_avg_voltage: an6 raw = 2.500000, factor = 1.000000
2021-06-29 13:47:10 power_api.c:60:_get_avg_voltage: chain 0, an0 = 18.460645, an2 18.460645, an6 2.500000.
2021-06-29 13:47:11 power_api.c:56:_get_avg_voltage: an6 raw = 2.503226, factor = 1.001290
2021-06-29 13:47:11 power_api.c:60:_get_avg_voltage: chain 2, an0 = 18.363403, an2 18.510310, an6 2.500000.
2021-06-29 13:47:12 power_api.c:56:_get_avg_voltage: an6 raw = 2.503226, factor = 1.001290
2021-06-29 13:47:12 power_api.c:60:_get_avg_voltage: chain 3, an0 = 18.461341, an2 18.461341, an6 2.500000.
2021-06-29 13:47:12 power_api.c:85:_get_avg_voltage: average_voltage = 18.477432
2021-06-29 13:47:12 power_api.c:106:check_voltage: target_vol = 18.50, actural_vol = 18.48, check voltage passed.
2021-06-29 13:47:12 thread.c:1472:create_check_system_status_thread: create thread
2021-06-29 13:47:12 driver-btm-api.c:2758:bitmain_soc_init: Init done!
2021-06-29 13:47:12 driver-btm-api.c:222:set_miner_status: STATUS_INIT
2021-06-29 13:47:18 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-06-29 13:47:19 frequency.c:316:get_sale_hash_rate_GH: g_sale_hash_rate = 58000
2021-06-29 13:47:22 driver-btm-api.c:1539:dhash_chip_send_job: Version num 1.
2021-06-29 13:47:32 driver-btm-api.c:1539:dhash_chip_send_job: Version num 4.
2021-06-29 13:47:32 driver-btm-api.c:1686:dhash_chip_send_job: stime.tv_sec 1624974452, block_ntime 1624974451

After a while i got these errors and of hash board get down:
Code:
2021-06-29 13:22:22 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:23 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 0
2021-06-29 13:22:23 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 1
2021-06-29 13:22:23 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 0
2021-06-29 13:22:24 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 1
2021-06-29 13:22:24 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 0 times.
2021-06-29 13:22:24 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 0
2021-06-29 13:22:24 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:24 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 1
2021-06-29 13:22:26 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 1 times.
2021-06-29 13:22:26 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:27 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 0
2021-06-29 13:22:27 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 1
2021-06-29 13:22:27 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 0
2021-06-29 13:22:28 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 1
2021-06-29 13:22:28 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 2 times.
2021-06-29 13:22:28 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 0
2021-06-29 13:22:28 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:28 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 1
2021-06-29 13:22:30 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 3 times.
2021-06-29 13:22:30 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:31 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 0
2021-06-29 13:22:31 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 1
2021-06-29 13:22:32 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 0
2021-06-29 13:22:32 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 4 times.
2021-06-29 13:22:32 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 1
2021-06-29 13:22:32 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:32 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 0
2021-06-29 13:22:33 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 1
2021-06-29 13:22:34 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 5 times.
2021-06-29 13:22:34 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:35 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 0
2021-06-29 13:22:35 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 1
2021-06-29 13:22:36 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 0
2021-06-29 13:22:36 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 6 times.
2021-06-29 13:22:36 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 1
2021-06-29 13:22:36 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:36 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 0
2021-06-29 13:22:37 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 1
2021-06-29 13:22:38 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 7 times.
2021-06-29 13:22:38 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:39 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 0
2021-06-29 13:22:40 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 1
2021-06-29 13:22:40 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 8 times.
2021-06-29 13:22:40 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 0
2021-06-29 13:22:40 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:40 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 1
2021-06-29 13:22:41 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 0
2021-06-29 13:22:41 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 1
2021-06-29 13:22:42 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 9 times.
2021-06-29 13:22:42 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:43 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 0
2021-06-29 13:22:44 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 1, chip = 40, reg = 1
2021-06-29 13:22:44 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 10 times.
2021-06-29 13:22:44 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 0
2021-06-29 13:22:44 thread.c:1372:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 10, require 44, failed times 1: oooo oooo xxoo xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx
2021-06-29 13:22:44 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 2, chip = 175, reg = 1
2021-06-29 13:22:45 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 0
2021-06-29 13:22:45 temperature.c:924:get_temp_info: read temp sensor failed: chain = 3, sensor = 3, chip = 160, reg = 1
2021-06-29 13:22:45 temperature.c:956:get_temp_info: ERROR: chain 3 can get NONE temp info or temp value abnormal, power it off
2021-06-29 13:22:46 thread.c:1392:asic_status_monitor_thread: chain 3 can't get enough hashrate reg val for 11 times.
2021-06-29 13:22:46 thread.c:1364:asic_status_monitor_thread: ERROR: chain 3 get hashrate_reg_counter 0, require 44, failed times 1
2021-06-29 13:22:47 frequency.c:316:get_sale_hash_rate_GH: g_sale_hash_rate = 37704

But after reboot miner, it returns back normally

https://s4.uupload.ir/files/screen_shot_2021-06-29_at_6.28.50_pm_oco9.png

Thanks
Jump to: