URGENT: Screwed Up Rockminer T1 Setup! (will donate bitcoin for help)

Kruuskop

newbie

Activity: 1

Merit: 0

a block errupter has a reset pinwhole as is than the admin is at 192.168.0.254 as your router is at 192.168.0.* range as changing the setup page network adress to like 192.168.1.99 you need to change 0 to 1 in routerrang from 192.168.0.1 lan and other settings as dhcp to 192.168.1.* as the device trys to connect to that range now and at other range cannot connect.. success
Hi,

Thanks for your interest in this, I really hope someone can help soon, it would be very much appreciated!

I am having problems setting up my Rockminer T1, and I almost had it set up until I did something very stupid.

I accidentally changed the Rockminer T1's IP address found in the administration panel when going to 192.168.etc... to an IP I don'the know and now I cannot get back in...

If anyone knows the solution or fix to this, and fast, I will pay you Bitcoin, whatever you think is fair.

Thank you so much!
[/quote]

knowndragon

newbie

Activity: 28

Merit: 0

I had issues with this has well. The pools for this thing suck. I wouldn't mind mining alt coins. At the time though I think I had success with dem but still didn't have the full hashing power I expected. I put in a wrong setting with my controller and thought I was screwed. Spent several frustrating hours trying to figure it out. Had to hook the controller to the computer to reset the device. Resetting was weird because there are no clear instructions on it. I hooked to the computer with Ethernet cable and had to press the reset button off and on several times before it reset and gave a really weird light reading. I then was able to reach it at the factory settings it shipped with.

drangos

full member

Activity: 200

Merit: 100

Quote from: jammies119 on September 08, 2014, 10:07:31 PM

So zoomhash sent me a new controller. Definitely working better now. I can stay connected to the rockminer over my network. Now the current issue is the thing will not start mining. Ive put in all the correct pool info for ghash.io just like it is on my Antminer S1s. I even tried the network cable im using to the Rockminer on one of the Antminers and it mines just fine. I tried putting the Rockminer in the DMZ on my router so it has access to all ports etc. Im at a loss here. Im starting to think the Rockminer is bad it self now. Thanks in advance for your help. Here are some screenshots of what my settings are.

Does it matter that the DIP switches are set so that it recognizes the boards as Board 1,2,3,4 when the label stickers on the machine say 13,14,15,16?

http://s17.postimg.org/5sp66z1m7/2014_09_08_21_18_48_BE200_Jet_Stratum_Miner.png
http://s16.postimg.org/i4cga6s9h/2014_09_08_21_19_34_BE200_Jet_Stratum_Miner.png

It seems most pools are not working with this crappy controller they gave you... i received my miner a few days ago and so far only ghash seems to work.
Address i use= uk1.ghash.io > than seperate the port in the box below ( 3333 ), user and pass and it should work.

If someone here find a way to get this t1 crap miner alive on any other pool let us know!
I realy tried all sort of ways, even tried to ssh in or get new software but it doesn't seem the exist.

Anyway hope someone could get this to work.

mazes321

newbie

Activity: 1

Merit: 0

Hi, I just joined the form.

I had the same issue and could not connect to IP address. Held the reset button in for 30 seconds (not sure how long required) and reset back to the factory 192.168.0.254. I was then able to connect and enter a new IP.

Hoping someone can help me with the next step.
I've entered all the details in the settings and it does not mine, but resets the session time about every 4 seconds. The controller has 1 blinking light (left), center is on, and right is off.

Using the same settings as older miner to connect to bitcoincz through proxy.

If anyone has suggestions would be appreciated.

Thanks

***UPDATE*** Used bitcoincz settings instead of proxy and it started mining. Confused as I had tried this several times already with no success but will leave as is.

jammies119

newbie

Activity: 3

Merit: 0

So zoomhash sent me a new controller. Definitely working better now. I can stay connected to the rockminer over my network. Now the current issue is the thing will not start mining. Ive put in all the correct pool info for ghash.io just like it is on my Antminer S1s. I even tried the network cable im using to the Rockminer on one of the Antminers and it mines just fine. I tried putting the Rockminer in the DMZ on my router so it has access to all ports etc. Im at a loss here. Im starting to think the Rockminer is bad it self now. Thanks in advance for your help. Here are some screenshots of what my settings are.

Does it matter that the DIP switches are set so that it recognizes the boards as Board 1,2,3,4 when the label stickers on the machine say 13,14,15,16?

http://s17.postimg.org/5sp66z1m7/2014_09_08_21_18_48_BE200_Jet_Stratum_Miner.png
http://s16.postimg.org/i4cga6s9h/2014_09_08_21_19_34_BE200_Jet_Stratum_Miner.png

cchan

sr. member

Activity: 379

Merit: 250

Run an IP scan software and if you find the unusual IP, try it.

jammies119

newbie

Activity: 3

Merit: 0

I am having this same problem. I tried resetting the setting by pushing the black reset button on the BE200 controller now it doesnt do anything. No link light activity and doesnt show up in my networks in windows when I plug in directly with a ethernet cable. Anyone find a fix for this yet?

lowbander80

legendary

Activity: 1036

Merit: 1000

did you try to run angryIP and see what IP is not regular on your network or try them all one by one
guess that you remember the pass

tipsysnake

newbie

Activity: 14

Merit: 0

If not then just find out the IP using and CMD or CLI command depending on youre operating system. There are many free tools can help you figure out IP's that are connected. just google them :-)

tipsysnake

newbie

Activity: 14

Merit: 0

Are the lights flashing when the Eth cable is plugged in?

tipsysnake

newbie

Activity: 14

Merit: 0

Can you ping it on the ip you set?

CashWWWeb

newbie

Activity: 13

Merit: 0

IF ANYONE HAS A SOLUTION AND CAN HELP ME WITH MY PROBLEM OVER SKYPE I WILL GLADLY PAY YOU IN BITCOIN.

THANKS!

SKYPE: CashWWWeb

CashWWWeb

newbie

Activity: 13

Merit: 0

Quote from: Vortex20000 on September 03, 2014, 03:59:51 AM

PMing a solution.

I didn't get any other PM's from you after the first. Please reply, thank you!

UPDATE: Sorry, was messaging someone else, just messaged you.

Vortex20000

hero member

Activity: 504

Merit: 500

sucker got hacked and screwed --Toad

PMing a solution.

CashWWWeb

newbie

Activity: 13

Merit: 0

Bump please.

CashWWWeb

newbie

Activity: 13

Merit: 0

Quote from: Newar on September 01, 2014, 02:29:08 AM

Have you tried to connect it directly to your computer and change the IP then? You might need a crossover cable ( https://en.wikipedia.org/wiki/Ethernet_crossover_cable ), but it might work with a regular ethernet cable too, depending on the hardware.

Yeah that was the way I was first able to get into the T1's admin area, by reading Dogie's Rockminer T1 Setup and following the Alternative Subnet Change method. I connected a short Ethernet cable from the Block Erupter Ethernet Controller (BE Controller) to my PC... but then after changing the IP address, subnet, gateway to something else, and pressing save/update, I haven't been able to get back in since :/

Hope I can find a solution soon, thanks.

Newar

legendary

Activity: 1358

Merit: 1001

https://gliph.me/hUF

Have you tried to connect it directly to your computer and change the IP then? You might need a crossover cable ( https://en.wikipedia.org/wiki/Ethernet_crossover_cable ), but it might work with a regular ethernet cable too, depending on the hardware.

CashWWWeb

newbie

Activity: 13

Merit: 0

Hi,

Thanks for your interest in this, I really hope someone can help soon, it would be very much appreciated!

I am having problems setting up my Rockminer T1, and I almost had it set up until I did something very stupid.

I accidentally changed the Rockminer T1's IP address found in the administration panel when going to 192.168.etc... to an IP I don'the know and now I cannot get back in...

If anyone knows the solution or fix to this, and fast, I will pay you Bitcoin, whatever you think is fair.

Thank you so much!

Topic: URGENT: Screwed Up Rockminer T1 Setup! (will donate bitcoin for help) (Read 3503 times)