Author

Topic: Why is this S9 only hashing 0.5th? (Read 217 times)

legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
September 06, 2018, 07:01:15 PM
#5
I am not sure where you got this information but it is not true. S9s dont downclock they just shut off when they get too hot.

Also, they dont shut off until much higher than 80c.

Honestly, I just found that idea from the blog posts before and I am trying to find it somewhere, but I can't find it.

tim-bc might be right it is a power issue/PSU issue or it may be a damaged hashing board (damaged chips) can be also the cause of hashrate dropped. But according to the image, it looks like the hashboard is working fine so PSU might be the cause of the drop hashrate.
full member
Activity: 294
Merit: 129
September 06, 2018, 04:59:37 PM
#4
Yes its because of the high temp if you reach 80+ (for auto tune firmware) it will automatically reduce the  hashing rate and it leads to high temp protection.

I am not sure where you got this information but it is not true. S9s dont downclock they just shut off when they get too hot.

Also, they dont shut off until much higher than 80c.
full member
Activity: 538
Merit: 175
September 05, 2018, 10:13:04 PM
#3
Hi, were you able to figure this out?

Unfortunately not. I don't remember so much about this one... I do know that it wasn't temperature related. I lost track of which miner it was, but if I had to guess now I'd say there was probably something funky going on with the PSU. Back then I wasn't using singleboardtest yet so I can't be sure.
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
July 26, 2018, 05:17:38 PM
#2
Yes its because of the high temp if you reach 80+ (for auto tune firmware) it will automatically reduce the  hashing rate and it leads to high temp protection.

According you your kernel log your miner is pushing higher frequency so I think you can try reducing frequency first and increasing the fan speed and you must take the hot air out from the room to make sure that the hot air is not sucking back to intake air.
full member
Activity: 538
Merit: 175
July 26, 2018, 03:04:38 PM
#1
I wonder why this miner is so slow. You can see that the speeds of most of the chips are reading 0 in the kernel log even though all of the chips are detected. Do you think it is temperature-related?

https://i.stack.imgur.com/XjYEO.png

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000315] ps7-ttc #0 at df804000, irq=43
[    0.000627] Console: colour dummy device 80x30
[    0.000658] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040212] pid_max: default: 32768 minimum: 301
[    0.040439] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040458] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042625] CPU: Testing write buffer coherency: ok
[    0.042975] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043036] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043262] L310 cache controller enabled
[    0.043282] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121045] CPU1: Booted secondary processor
[    0.210231] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210367] Brought up 2 CPUs
[    0.210387] SMP: Total of 2 processors activated.
[    0.210396] CPU: All CPU(s) started in SVC mode.
[    0.211070] devtmpfs: initialized
[    0.213499] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214755] regulator-dummy: no parameters
[    0.223751] NET: Registered protocol family 16
[    0.226013] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.228341] cpuidle: using governor ladder
[    0.228355] cpuidle: using governor menu
[    0.235916] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.237469] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.237482] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.237602] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.259862] bio: create slab at 0
[    0.261515] vgaarb: loaded
[    0.262245] SCSI subsystem initialized
[    0.263138] usbcore: registered new interface driver usbfs
[    0.263323] usbcore: registered new interface driver hub
[    0.263554] usbcore: registered new device driver usb
[    0.264083] media: Linux media interface: v0.10
[    0.264244] Linux video capture interface: v2.00
[    0.264490] pps_core: LinuxPPS API ver. 1 registered
[    0.264502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.264629] PTP clock support registered
[    0.265013] EDAC MC: Ver: 3.0.0
[    0.266090] Advanced Linux Sound Architecture Driver Initialized.
[    0.269112] DMA-API: preallocated 4096 debug entries
[    0.269127] DMA-API: debugging enabled by kernel config
[    0.269221] Switched to clocksource arm_global_timer
[    0.291343] NET: Registered protocol family 2
[    0.292019] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.292076] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.292161] TCP: Hash tables configured (established 4096 bind 4096)
[    0.292207] TCP: reno registered
[    0.292225] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.292259] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.292498] NET: Registered protocol family 1
[    0.292872] RPC: Registered named UNIX socket transport module.
[    0.292884] RPC: Registered udp transport module.
[    0.292892] RPC: Registered tcp transport module.
[    0.292901] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.292915] PCI: CLS 0 bytes, default 64
[    0.293365] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.295437] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.297597] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.297793] msgmni has been set to 967
[    0.298591] io scheduler noop registered
[    0.298605] io scheduler deadline registered
[    0.298643] io scheduler cfq registered (default)
[    0.311387] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.311407] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.435559] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.003818] console [ttyPS0] enabled
[    1.008136] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.015792] [drm] Initialized drm 1.1.0 20060810
[    1.033060] brd: module loaded
[    1.042508] loop: module loaded
[    1.052295] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.058042] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.066222] libphy: XEMACPS mii bus: probed
[    1.070883] ------------- phy_id = 0x3625e62
[    1.075627] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.084262] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.090935] ehci-pci: EHCI PCI platform driver
[    1.098156] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.104991] usbcore: registered new interface driver usb-storage
[    1.111876] mousedev: PS/2 mouse device common for all mice
[    1.117980] i2c /dev entries driver
[    1.124958] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.130560] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.136455] Xilinx Zynq CpuIdle Driver started
[    1.141331] sdhci: Secure Digital Host Controller Interface driver
[    1.147428] sdhci: Copyright(c) Pierre Ossman
[    1.151842] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.158591] mmc0: no vqmmc regulator found
[    1.162635] mmc0: no vmmc regulator found
[    1.199238] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.207925] usbcore: registered new interface driver usbhid
[    1.213443] usbhid: USB HID core driver
[    1.218169] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.224470] nand: Micron MT29F2G08ABAEAWP
[    1.228434] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.234376] Bad block table found at page 131008, version 0x01
[    1.240602] Bad block table found at page 130944, version 0x01
[    1.246652] 3 ofpart partitions found on MTD device pl353-nand
[    1.252434] Creating 3 MTD partitions on "pl353-nand":
[    1.257524] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.265618] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.272961] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.281990] TCP: cubic registered
[    1.285228] NET: Registered protocol family 17
[    1.289947] Registering SWP/SWPB emulation handler
[    1.295870] regulator-dummy: disabling
[    1.300266] UBI: attaching mtd1 to ubi0
[    1.827225] UBI: scanning is finished
[    1.839032] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.846111] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.852874] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.859559] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.866394] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.872396] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.879519] UBI: max/mean erase counter: 304/88, WL threshold: 4096, image sequence number: 1283732989
[    1.888790] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.898024] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.898029] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.902088] ALSA device list:
[    1.902092]   No soundcards found.
[    1.918491] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.978308] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.984270] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.993371] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.003256] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.008285] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model
[    2.019878] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.027290] devtmpfs: mounted
[    2.030426] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.871067] random: dd urandom read with 0 bits of entropy available
[    3.269265]
[    3.269265] bcm54xx_config_init
[    3.879253]
[    3.879253] bcm54xx_config_init
[    7.880085] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.886186] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   25.896773] In axi fpga driver!
[   25.899868] request_mem_region OK!
[   25.903237] AXI fpga dev virtual address is 0xdf9fc000
[   25.908341] *base_vir_addr = 0x8c510
[   25.924204] In fpga mem driver!
[   25.927300] request_mem_region OK!
[   25.930917] fpga mem virtual address is 0xe2000000
[   26.738424]
[   26.738424] bcm54xx_config_init
[   27.368331]
[   27.368331] bcm54xx_config_init
[   31.368648] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   31.374751] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[  431.573919] random: nonblocking pool is initialized
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : (redacted)
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[1] has core num=1
Chain[5] ASIC[2] has core num=2
Chain[5] ASIC[3] has core num=1
Chain[5] ASIC[4] has core num=4
Chain[5] ASIC[5] has core num=1
Chain[5] ASIC[6] has core num=1
Chain[5] ASIC[7] has core num=1
Chain[5] ASIC[8] has core num=1
Chain[5] ASIC[9] has core num=1
Chain[5] ASIC[10] has core num=2
Chain[5] ASIC[11] has core num=2
Chain[5] ASIC[12] has core num=1
Chain[5] ASIC[14] has core num=2
Chain[5] ASIC[15] has core num=1
Chain[5] ASIC[16] has core num=3
Chain[5] ASIC[17] has core num=2
Chain[5] ASIC[18] has core num=2
Chain[5] ASIC[19] has core num=1
Chain[5] ASIC[20] has core num=1
Chain[5] ASIC[21] has core num=1
Chain[5] ASIC[22] has core num=1
Chain[5] ASIC[23] has core num=1
Chain[5] ASIC[24] has core num=1
Chain[5] ASIC[25] has core num=1
Chain[5] ASIC[26] has core num=3
Chain[5] ASIC[29] has core num=1
Chain[5] ASIC[30] has core num=2
Chain[5] ASIC[33] has core num=4
Chain[5] ASIC[34] has core num=2
Chain[5] ASIC[35] has core num=1
Chain[5] ASIC[36] has core num=1
Chain[5] ASIC[37] has core num=1
Chain[5] ASIC[38] has core num=1
Chain[5] ASIC[39] has core num=1
Chain[5] ASIC[40] has core num=1
Chain[5] ASIC[41] has core num=1
Chain[5] ASIC[42] has core num=1
Chain[5] ASIC[43] has core num=1
Chain[5] ASIC[44] has core num=3
Chain[5] ASIC[45] has core num=6
Chain[5] ASIC[46] has core num=1
Chain[5] ASIC[47] has core num=1
Chain[5] ASIC[48] has core num=1
Chain[5] ASIC[49] has core num=1
Chain[5] ASIC[50] has core num=2
Chain[5] ASIC[51] has core num=2
Chain[5] ASIC[52] has core num=1
Chain[5] ASIC[53] has core num=1
Chain[5] ASIC[54] has core num=1
Chain[5] ASIC[55] has core num=1
Chain[5] ASIC[56] has core num=2
Chain[5] ASIC[57] has core num=1
Chain[5] ASIC[58] has core num=8
Chain[5] ASIC[59] has core num=15
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[48] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[16] has core num=2
Chain[7] ASIC[35] has core num=2
Check chain[7] PIC fw version=0x03
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=91 on chain[7], value=890
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,41,28
chain[5] temp chip I2C addr=0x9a
chain[6] temp offset record: 62,0,0,0,0,0,41,28
chain[6] temp chip I2C addr=0x9a
chain[7] temp offset record: 62,0,0,0,0,0,41,28
chain[7] temp chip I2C addr=0x9a
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1378 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found= 1603 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:37:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : (redacted)
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[5] speed=5760
get fan[2] speed=6000
get fan[5] speed=5760
get fan[2] speed=6000
get fan[5] speed=5760
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=890
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=125 value=870
Chain[J7] orignal chain_voltage_pic=91 value=890
Chain[J8] orignal chain_voltage_pic=91 value=890
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[1] has core num=1
Chain[J6] ASIC[2] has core num=2
Chain[J6] ASIC[3] has core num=1
Chain[J6] ASIC[4] has core num=4
Chain[J6] ASIC[5] has core num=1
Chain[J6] ASIC[6] has core num=1
Chain[J6] ASIC[7] has core num=1
Chain[J6] ASIC[8] has core num=1
Chain[J6] ASIC[9] has core num=1
Chain[J6] ASIC[10] has core num=2
Chain[J6] ASIC[11] has core num=2
Chain[J6] ASIC[12] has core num=1
Chain[J6] ASIC[14] has core num=2
Chain[J6] ASIC[15] has core num=1
Chain[J6] ASIC[16] has core num=3
Chain[J6] ASIC[17] has core num=2
Chain[J6] ASIC[18] has core num=2
Chain[J6] ASIC[19] has core num=1
Chain[J6] ASIC[20] has core num=1
Chain[J6] ASIC[21] has core num=1
Chain[J6] ASIC[22] has core num=1
Chain[J6] ASIC[23] has core num=1
Chain[J6] ASIC[24] has core num=1
Chain[J6] ASIC[25] has core num=1
Chain[J6] ASIC[26] has core num=3
Chain[J6] ASIC[29] has core num=1
Chain[J6] ASIC[30] has core num=2
Chain[J6] ASIC[33] has core num=4
Chain[J6] ASIC[34] has core num=2
Chain[J6] ASIC[35] has core num=1
Chain[J6] ASIC[36] has core num=1
Chain[J6] ASIC[37] has core num=1
Chain[J6] ASIC[38] has core num=1
Chain[J6] ASIC[39] has core num=1
Chain[J6] ASIC[40] has core num=1
Chain[J6] ASIC[41] has core num=1
Chain[J6] ASIC[42] has core num=1
Chain[J6] ASIC[43] has core num=1
Chain[J6] ASIC[44] has core num=3
Chain[J6] ASIC[45] has core num=6
Chain[J6] ASIC[46] has core num=1
Chain[J6] ASIC[47] has core num=1
Chain[J6] ASIC[48] has core num=1
Chain[J6] ASIC[49] has core num=1
Chain[J6] ASIC[50] has core num=2
Chain[J6] ASIC[51] has core num=2
Chain[J6] ASIC[52] has core num=1
Chain[J6] ASIC[53] has core num=1
Chain[J6] ASIC[54] has core num=1
Chain[J6] ASIC[55] has core num=1
Chain[J6] ASIC[56] has core num=2
Chain[J6] ASIC[57] has core num=1
Chain[J6] ASIC[58] has core num=8
Chain[J6] ASIC[59] has core num=15
Chain[J7] has core num in PIC
Chain[J7] ASIC[48] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[16] has core num=2
Chain[J8] ASIC[35] has core num=2
miner total rate=13772GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:675
Asic[ 1]:675 Asic[ 2]:675 Asic[ 3]:675 Asic[ 4]:675 Asic[ 5]:675 Asic[ 6]:675 Asic[ 7]:675 Asic[ 8]:675
Asic[ 9]:675 Asic[10]:675 Asic[11]:675 Asic[12]:675 Asic[13]:675 Asic[14]:675 Asic[15]:675 Asic[16]:675
Asic[17]:675 Asic[18]:675 Asic[19]:675 Asic[20]:675 Asic[21]:675 Asic[22]:675 Asic[23]:675 Asic[24]:675
Asic[25]:675 Asic[26]:675 Asic[27]:675 Asic[28]:675 Asic[29]:675 Asic[30]:675 Asic[31]:675 Asic[32]:675
Asic[33]:675 Asic[34]:675 Asic[35]:675 Asic[36]:675 Asic[37]:675 Asic[38]:675 Asic[39]:675 Asic[40]:675
Asic[41]:675 Asic[42]:675 Asic[43]:675 Asic[44]:675 Asic[45]:675 Asic[46]:675 Asic[47]:675 Asic[48]:675
Asic[49]:675 Asic[50]:675 Asic[51]:675 Asic[52]:675 Asic[53]:675 Asic[54]:675 Asic[55]:675 Asic[56]:675
Asic[57]:675 Asic[58]:675 Asic[59]:675 Asic[60]:675 Asic[61]:675 Asic[62]:675
Chain:5 max freq=675
Chain:5 min freq=675

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:6 max freq=631
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:7 max freq=631
Chain:7 min freq=631


Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Detect a bad chip=59 on chain[5], fixed to 400M
Asic[59]:675 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:5 max freq=675
Chain:5 min freq=650

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:6 max freq=631
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:7 max freq=631
Chain:7 min freq=631

max freq = 675
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,41,28
chain[5] temp chip I2C addr=0x9a
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
Warning: Chain[5] chip[244] local:66 remote:-128 offset:-28, will fixed offset=27
New offset Chain[5] chip[244] local:66 remote:-128 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,41,28
chain[6] temp chip I2C addr=0x9a
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:60 remote:60 offset:33
Chain[J7] chip[244] get middle temp offset=33 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,41,28
chain[7] temp chip I2C addr=0x9a
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:53 remote:50 offset:36
Chain[J8] chip[244] get middle temp offset=36 typeID=55
single board rate=4575 voltage limit=890 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 890
retryFlag=1 will set the voltage limited on chain[5], change voltage=890
now set pic voltage=91 on chain[5]
single board rate=4531 voltage limit=890 on chain[6]
get PIC voltage=890 on chain[6], check: must be < 890
retryFlag=1 will set the voltage limited on chain[6], change voltage=890
now set pic voltage=91 on chain[6]
single board rate=4529 voltage limit=890 on chain[7]
get PIC voltage=890 on chain[7], check: must be < 890
retryFlag=1 will set the voltage limited on chain[7], change voltage=890
now set pic voltage=91 on chain[7]
Chain[J6] set working voltage=890 [91]
Chain[J7] set working voltage=890 [91]
Chain[J8] set working voltage=890 [91]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=908 asic[02]=911 asic[03]=911 asic[04]=900 asic[05]=906 asic[06]=907 asic[07]=911
asic[08]=908 asic[09]=910 asic[10]=906 asic[11]=906 asic[12]=908 asic[13]=912 asic[14]=910 asic[15]=911
asic[16]=902 asic[17]=909 asic[18]=905 asic[19]=908 asic[20]=907 asic[21]=910 asic[22]=907 asic[23]=909
asic[24]=906 asic[25]=909 asic[26]=902 asic[27]=912 asic[28]=912 asic[29]=908 asic[30]=907 asic[31]=912
asic[32]=912 asic[33]=896 asic[34]=905 asic[35]=908 asic[36]=908 asic[37]=909 asic[38]=906 asic[39]=907
asic[40]=909 asic[41]=909 asic[42]=910 asic[43]=908 asic[44]=904 asic[45]=907 asic[46]=907 asic[47]=911
asic[48]=907 asic[49]=909 asic[50]=906 asic[51]=902 asic[52]=910 asic[53]=907 asic[54]=907 asic[55]=909
asic[56]=906 asic[57]=908 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[01]=908
core[012]=4

asic[02]=911
core[100]=7

asic[03]=911
core[011]=7

asic[04]=900
core[005]=4 core[054]=4 core[056]=7 core[095]=5

asic[05]=906
core[063]=2

asic[06]=907
core[030]=3

asic[07]=911
core[003]=7

asic[08]=908
core[039]=4

asic[09]=910
core[107]=6

asic[10]=906
core[062]=6 core[110]=4

asic[11]=906
core[042]=2

asic[12]=908
core[017]=4

asic[14]=910
core[080]=7 core[105]=7

asic[15]=911
core[084]=7

asic[16]=902
core[020]=3 core[072]=4 core[093]=7

asic[17]=909
core[070]=7 core[078]=6

asic[18]=905
core[008]=5 core[018]=4

asic[19]=908
core[090]=4

asic[20]=907
core[047]=3

asic[21]=910
core[072]=6

asic[22]=907
core[027]=3

asic[23]=909
core[062]=5

asic[24]=906
core[049]=2

asic[25]=909
core[064]=5

asic[26]=902
core[037]=6 core[043]=6 core[057]=2

asic[29]=908
core[033]=4

asic[30]=907
core[003]=4 core[020]=7

asic[33]=896
core[003]=4 core[034]=6 core[085]=3 core[100]=3

asic[34]=905
core[087]=5 core[112]=4

asic[35]=908
core[032]=4

asic[36]=908
core[004]=4

asic[37]=909
core[049]=5

asic[38]=906
core[097]=2

asic[39]=907
core[038]=3

asic[40]=909
core[057]=5

asic[41]=909
core[053]=5

asic[42]=910
core[000]=6

asic[43]=908
core[034]=4

asic[44]=904
core[039]=7 core[096]=5 core[098]=4

asic[45]=907
core[078]=3

asic[46]=907
core[056]=3

asic[47]=911
core[047]=7

asic[48]=907
core[104]=3

asic[49]=909
core[054]=5

asic[50]=906
core[056]=7 core[096]=3

asic[51]=902
core[053]=3 core[056]=3

asic[52]=910
core[068]=6

asic[53]=907
core[113]=3

asic[54]=907
core[074]=3

asic[55]=909
core[098]=5

asic[56]=906
core[038]=6 core[062]=4

asic[57]=908
core[030]=4



freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=656 freq[06]=656 freq[07]=656
freq[08]=656 freq[09]=656 freq[10]=656 freq[11]=656 freq[12]=656 freq[13]=656 freq[14]=656 freq[15]=656
freq[16]=656 freq[17]=656 freq[18]=656 freq[19]=656 freq[20]=656 freq[21]=656 freq[22]=656 freq[23]=656
freq[24]=656 freq[25]=656 freq[26]=656 freq[27]=656 freq[28]=656 freq[29]=656 freq[30]=656 freq[31]=656
freq[32]=656 freq[33]=656 freq[34]=656 freq[35]=656 freq[36]=656 freq[37]=656 freq[38]=656 freq[39]=656
freq[40]=656 freq[41]=656 freq[42]=656 freq[43]=656 freq[44]=656 freq[45]=656 freq[46]=656 freq[47]=656
freq[48]=656 freq[49]=656 freq[50]=656 freq[51]=656 freq[52]=656 freq[53]=656 freq[54]=656 freq[55]=656
freq[56]=656 freq[57]=656 freq[58]=656 freq[59]=675 freq[60]=656 freq[61]=656 freq[62]=656

total valid nonce number:57209
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26562
last_nonce_num:21492
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=908
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[23]=908
core[085]=4



freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631

total valid nonce number:57452
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25845
last_nonce_num:28626
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25840
last_nonce_num:28610
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: OK!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
do heat board 8xPatten for 2 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=908 asic[02]=911 asic[03]=911 asic[04]=900 asic[05]=906 asic[06]=907 asic[07]=911
asic[08]=908 asic[09]=910 asic[10]=906 asic[11]=906 asic[12]=908 asic[13]=912 asic[14]=910 asic[15]=911
asic[16]=903 asic[17]=909 asic[18]=905 asic[19]=908 asic[20]=907 asic[21]=910 asic[22]=907 asic[23]=909
asic[24]=906 asic[25]=909 asic[26]=901 asic[27]=912 asic[28]=911 asic[29]=908 asic[30]=907 asic[31]=912
asic[32]=912 asic[33]=896 asic[34]=905 asic[35]=908 asic[36]=908 asic[37]=909 asic[38]=906 asic[39]=907
asic[40]=909 asic[41]=909 asic[42]=909 asic[43]=908 asic[44]=904 asic[45]=907 asic[46]=907 asic[47]=911
asic[48]=907 asic[49]=909 asic[50]=906 asic[51]=902 asic[52]=910 asic[53]=907 asic[54]=907 asic[55]=909
asic[56]=906 asic[57]=908 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[01]=908
core[012]=4

asic[02]=911
core[100]=7

asic[03]=911
core[011]=7

asic[04]=900
core[005]=4 core[054]=4 core[056]=7 core[095]=5

asic[05]=906
core[063]=2

asic[06]=907
core[030]=3

asic[07]=911
core[003]=7

asic[08]=908
core[039]=4

asic[09]=910
core[107]=6

asic[10]=906
core[062]=6 core[110]=4

asic[11]=906
core[042]=2

asic[12]=908
core[017]=4

asic[14]=910
core[080]=7 core[105]=7

asic[15]=911
core[084]=7

asic[16]=903
core[020]=3 core[072]=5 core[093]=7

asic[17]=909
core[070]=7 core[078]=6

asic[18]=905
core[008]=5 core[018]=4

asic[19]=908
core[090]=4

asic[20]=907
core[047]=3

asic[21]=910
core[072]=6

asic[22]=907
core[027]=3

asic[23]=909
core[062]=5

asic[24]=906
core[049]=2

asic[25]=909
core[064]=5

asic[26]=901
core[037]=6 core[043]=5 core[057]=2

asic[28]=911
core[096]=7

asic[29]=908
core[033]=4

asic[30]=907
core[003]=4 core[020]=7

asic[33]=896
core[003]=4 core[034]=6 core[085]=3 core[100]=3

asic[34]=905
core[087]=5 core[112]=4

asic[35]=908
core[032]=4

asic[36]=908
core[004]=4

asic[37]=909
core[049]=5

asic[38]=906
core[097]=2

asic[39]=907
core[038]=3

asic[40]=909
core[057]=5

asic[41]=909
core[053]=5

asic[42]=909
core[000]=5

asic[43]=908
core[034]=4

asic[44]=904
core[039]=7 core[096]=5 core[098]=4

asic[45]=907
core[078]=3

asic[46]=907
core[056]=3

asic[47]=911
core[047]=7

asic[48]=907
core[104]=3

asic[49]=909
core[054]=5

asic[50]=906
core[056]=7 core[096]=3

asic[51]=902
core[053]=3 core[056]=3

asic[52]=910
core[068]=6

asic[53]=907
core[113]=3

asic[54]=907
core[074]=3

asic[55]=909
core[098]=5

asic[56]=906
core[038]=6 core[062]=4

asic[57]=908
core[030]=4



freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=656 freq[06]=656 freq[07]=656
freq[08]=656 freq[09]=656 freq[10]=656 freq[11]=656 freq[12]=656 freq[13]=656 freq[14]=656 freq[15]=656
freq[16]=656 freq[17]=656 freq[18]=656 freq[19]=656 freq[20]=656 freq[21]=656 freq[22]=656 freq[23]=656
freq[24]=656 freq[25]=656 freq[26]=656 freq[27]=656 freq[28]=656 freq[29]=656 freq[30]=656 freq[31]=656
freq[32]=656 freq[33]=656 freq[34]=656 freq[35]=656 freq[36]=656 freq[37]=656 freq[38]=656 freq[39]=656
freq[40]=656 freq[41]=656 freq[42]=656 freq[43]=656 freq[44]=656 freq[45]=656 freq[46]=656 freq[47]=656
freq[48]=656 freq[49]=656 freq[50]=656 freq[51]=656 freq[52]=656 freq[53]=656 freq[54]=656 freq[55]=656
freq[56]=656 freq[57]=656 freq[58]=656 freq[59]=675 freq[60]=656 freq[61]=656 freq[62]=656

total valid nonce number:57207
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26580
last_nonce_num:48711
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=908
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[23]=908
core[085]=4



freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631

total valid nonce number:57452
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25864
last_nonce_num:48718
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25866
last_nonce_num:48722
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
setStartTimePoint total_tv_start_sys=383 total_tv_end_sys=384
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=754.974 Asic[02]=989.855 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=2.86800 Asic[29]=58.3510 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000
Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=0.00000 Asic[40]=0.00000
Asic[41]=0.00000 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=0.00000

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=69.4910 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=28.6210 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=872.415 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=0.00000 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000
Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=5.77100 Asic[40]=0.00000
Asic[41]=1.94600 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=2.53300

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=70.4810 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=72.2760 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=56.3210
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=0.00000 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000
Asic[33]=15.8880 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=0.00000 Asic[40]=0.00000
Asic[41]=14.9310 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=41.1370 Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Asic[01]=754.974000
Asic[02]=989.855000
Asic[53]=115.897000
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Asic[19]=872.415000
Asic[56]=222.180000
Asic[60]=156.128000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[56]=213.305000
Asic[60]=156.833000
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
read failed, old value: Chain[5] Chip[62] local Temp=85
read failed on Chain[5] Chip[62] middle Temp old value:100
Special fix Chain[5] Chip[62] middle Temp = 100
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=33
read failed, old value: Chain[6] Chip[62] local Temp=78
read failed on Chain[6] Chip[62] middle Temp old value:93
Special fix Chain[6] Chip[62] middle Temp = 93
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=36
read failed, old value: Chain[7] Chip[62] local Temp=72
read failed on Chain[7] Chip[62] middle Temp old value:87
Special fix Chain[7] Chip[62] middle Temp = 87
Done read temp on Chain[7]
Set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=60121
Jump to: