everything can be possible:
1. the problem with PSU (cables)
2. The powering for/to USB Riser
3. USB Riser/ loose installation.
4. Windows is corrupt
5. a dummy output.
Topic: 0 Hashrate on 1/6 Rx 580 nitro+ gpu , breaks whole Rig - page 2. (Read 340 times)
So i managed to switch the PSU this weekend, but the problem is not from here.Any other suggestions?
From the looks of it and troubleshootings done on these two suspected parts
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
PSU problem?MB problem?
you might probably have a faulty board
just wonder if a certain PCI-e slot filled then crash, then taking it empty will be ok
try it out
to use 6+ GPUs on Windows you should -
1) turn on Above 4G Decoding in UEFI settings
2) your hard disk drive should use GPT partition scheme
3) and you should boot Windows in UEFI mode (BIOS/CSM/Legacy mode won't work and WILL cause issues exactly like yours when mining with more than 5 cards).
more info about converting your Windows installation to GPT/UEFI boot mode here -
https://www.windowscentral.com/how-convert-mbr-disk-gpt-move-bios-uefi-windows-10
1) turn on Above 4G Decoding in UEFI settings
2) your hard disk drive should use GPT partition scheme
3) and you should boot Windows in UEFI mode (BIOS/CSM/Legacy mode won't work and WILL cause issues exactly like yours when mining with more than 5 cards).
more info about converting your Windows installation to GPT/UEFI boot mode here -
https://www.windowscentral.com/how-convert-mbr-disk-gpt-move-bios-uefi-windows-10
1st if GPU is OC then revise to default value and run for few hours to check, If still the same problem then change check Sata Cable from PSU is okay not burned etc. then change riser sata cable then usb cable then riser.
Issue will be from above one of them. I believe
I had experienced this stuff when i do add up a card and troubleshooting up first on the PSU but i didnt resolve the issue. The problem is on sata cable is burned down.Issue will be from above one of them. I believe
OP, have you checked out those connections? Be sure not to miss a single one and be keen on burned parts.
Get better Air circulation around the rig. I had to shutdown the rigs due to too much heat and bad air circulation. I was getting similar issue
1st if GPU is OC then revise to default value and run for few hours to check, If still the same problem then change check Sata Cable from PSU is okay not burned etc. then change riser sata cable then usb cable then riser.
Issue will be from above one of them. I believe
Issue will be from above one of them. I believe
So i managed to switch the PSU this weekend, but the problem is not from here.Any other suggestions?
So i have a problem that i can't seem to be able to fix for awhile now
I have a rig with 6 x rx 580 nitro+ 8gb, dual core celeron, 4 gb ram, PSU EVGA 1300 w and a h110 d3a MB.This rig can only function with 5 gpus atm because as soon as i connect the 6th gpu , 2 other gpus along with the last connected gpu mine with 0, so i have 3 gpus that mine with 0.Soon after this happens i get blue screen, and restart.
I operate on windows 10, GPUS are all undervolted with -70 mv, core and memory 1090 and 2090.
I tried switching riser 2 times, switching gpu power cable , switching pci slot order, riser power cable and taking each gpu one at a time.
What i found out is the following.Gpu is fine and can mine ok when it is alone, all gpus are working actually so no problem from here.Risers are ok aswell(slot,cable and pci jack), power cable also.
Everything is ok when i add 2nd,3rd and 4th GPU.
Problem comes up when i add the 5th gpu this time from the opposite part of the rig, so that as soon as mining starts after dag is finished i can see that 2 or 3 cards mine with 0 , and soon after , error screen and restart.
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
Here are some screenshots
https://postimg.cc/gallery/2aqkgyupe/
add me on telegram tommyzjh, i do tuning and diagnostics for a fee.
I have a rig with 6 x rx 580 nitro+ 8gb, dual core celeron, 4 gb ram, PSU EVGA 1300 w and a h110 d3a MB.This rig can only function with 5 gpus atm because as soon as i connect the 6th gpu , 2 other gpus along with the last connected gpu mine with 0, so i have 3 gpus that mine with 0.Soon after this happens i get blue screen, and restart.
I operate on windows 10, GPUS are all undervolted with -70 mv, core and memory 1090 and 2090.
I tried switching riser 2 times, switching gpu power cable , switching pci slot order, riser power cable and taking each gpu one at a time.
What i found out is the following.Gpu is fine and can mine ok when it is alone, all gpus are working actually so no problem from here.Risers are ok aswell(slot,cable and pci jack), power cable also.
Everything is ok when i add 2nd,3rd and 4th GPU.
Problem comes up when i add the 5th gpu this time from the opposite part of the rig, so that as soon as mining starts after dag is finished i can see that 2 or 3 cards mine with 0 , and soon after , error screen and restart.
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
Here are some screenshots
https://postimg.cc/gallery/2aqkgyupe/
add me on telegram tommyzjh, i do tuning and diagnostics for a fee.
It's seem like your PSU problem, because as i know power consumption for each RX 580 is 40-80 w. So maybe your PSU something happen with it, even actually with that PSU is enough for 5-6 your GPU. And also about MB, you have tell us if has try every slot of PCIe, and everything is fine. Please try to replace it with other PSU.
It seem to be PSU 's problem
That PSU doesn't have enough power to operate all 6 cards
You should test with other PSU to make decision
That PSU doesn't have enough power to operate all 6 cards
You should test with other PSU to make decision
thank you , will try that in the following days and will let you know !
So i have a problem that i can't seem to be able to fix for awhile now
I have a rig with 6 x rx 580 nitro+ 8gb, dual core celeron, 4 gb ram, PSU EVGA 1300 w and a h110 d3a MB.This rig can only function with 5 gpus atm because as soon as i connect the 6th gpu , 2 other gpus along with the last connected gpu mine with 0, so i have 3 gpus that mine with 0.Soon after this happens i get blue screen, and restart.
I operate on windows 10, GPUS are all undervolted with -70 mv, core and memory 1090 and 2090.
I tried switching riser 2 times, switching gpu power cable , switching pci slot order, riser power cable and taking each gpu one at a time.
What i found out is the following.Gpu is fine and can mine ok when it is alone, all gpus are working actually so no problem from here.Risers are ok aswell(slot,cable and pci jack), power cable also.
Everything is ok when i add 2nd,3rd and 4th GPU.
Problem comes up when i add the 5th gpu this time from the opposite part of the rig, so that as soon as mining starts after dag is finished i can see that 2 or 3 cards mine with 0 , and soon after , error screen and restart.
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
Here are some screenshots
https://postimg.cc/gallery/2aqkgyupe/
I have a rig with 6 x rx 580 nitro+ 8gb, dual core celeron, 4 gb ram, PSU EVGA 1300 w and a h110 d3a MB.This rig can only function with 5 gpus atm because as soon as i connect the 6th gpu , 2 other gpus along with the last connected gpu mine with 0, so i have 3 gpus that mine with 0.Soon after this happens i get blue screen, and restart.
I operate on windows 10, GPUS are all undervolted with -70 mv, core and memory 1090 and 2090.
I tried switching riser 2 times, switching gpu power cable , switching pci slot order, riser power cable and taking each gpu one at a time.
What i found out is the following.Gpu is fine and can mine ok when it is alone, all gpus are working actually so no problem from here.Risers are ok aswell(slot,cable and pci jack), power cable also.
Everything is ok when i add 2nd,3rd and 4th GPU.
Problem comes up when i add the 5th gpu this time from the opposite part of the rig, so that as soon as mining starts after dag is finished i can see that 2 or 3 cards mine with 0 , and soon after , error screen and restart.
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
Here are some screenshots
https://postimg.cc/gallery/2aqkgyupe/
I have a feeling a PSU issue, Since you have still 3 working rigs identical I would suggest
- Take one of the working RIG's PSU and swap it to the faulty one
Troubleshooting if its truly a PSU prob.
So i have a problem that i can't seem to be able to fix for awhile now
I have a rig with 6 x rx 580 nitro+ 8gb, dual core celeron, 4 gb ram, PSU EVGA 1300 w and a h110 d3a MB.This rig can only function with 5 gpus atm because as soon as i connect the 6th gpu , 2 other gpus along with the last connected gpu mine with 0, so i have 3 gpus that mine with 0.Soon after this happens i get blue screen, and restart.
I operate on windows 10, GPUS are all undervolted with -70 mv, core and memory 1090 and 2090.
I tried switching riser 2 times, switching gpu power cable , switching pci slot order, riser power cable and taking each gpu one at a time.
What i found out is the following.Gpu is fine and can mine ok when it is alone, all gpus are working actually so no problem from here.Risers are ok aswell(slot,cable and pci jack), power cable also.
Everything is ok when i add 2nd,3rd and 4th GPU.
Problem comes up when i add the 5th gpu this time from the opposite part of the rig, so that as soon as mining starts after dag is finished i can see that 2 or 3 cards mine with 0 , and soon after , error screen and restart.
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
Here are some screenshots
https://postimg.cc/gallery/2aqkgyupe/
I have a rig with 6 x rx 580 nitro+ 8gb, dual core celeron, 4 gb ram, PSU EVGA 1300 w and a h110 d3a MB.This rig can only function with 5 gpus atm because as soon as i connect the 6th gpu , 2 other gpus along with the last connected gpu mine with 0, so i have 3 gpus that mine with 0.Soon after this happens i get blue screen, and restart.
I operate on windows 10, GPUS are all undervolted with -70 mv, core and memory 1090 and 2090.
I tried switching riser 2 times, switching gpu power cable , switching pci slot order, riser power cable and taking each gpu one at a time.
What i found out is the following.Gpu is fine and can mine ok when it is alone, all gpus are working actually so no problem from here.Risers are ok aswell(slot,cable and pci jack), power cable also.
Everything is ok when i add 2nd,3rd and 4th GPU.
Problem comes up when i add the 5th gpu this time from the opposite part of the rig, so that as soon as mining starts after dag is finished i can see that 2 or 3 cards mine with 0 , and soon after , error screen and restart.
What is this?I never encountered this problem before, i have 3 other rigs exactly like this and they all work fine and stable.
PSU problem?MB problem?
Here are some screenshots
https://postimg.cc/gallery/2aqkgyupe/
Jump to: