Author

Topic: 5 S9 Single Chip On My Devices Is Fault (Read 268 times)

legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
October 18, 2018, 01:26:35 PM
#11
Does it help us find the error? (kernel log)
~snip~

According to the log, one of the hashboard doesn't detect and the two hashboard is fine all ASIC chips are detected.

I think your title is misleading? The chip you are talking about it supposed to be "a hashing board" am I right?

Anyway, Have you tried to downgrade the firmware? I heard that November firmware can solve this issue, but the problem I don't have any source where to download it.
Try to flash it with this firmware Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz
Then check if it solves your issue if not please post the new "kernel logs"

The final solution that comes to my mind is to reflash it using "PICKIT 3". If the one of the hashboard is broken you can revive it by using "PICKIT 3" and you can fully erase the program then reflash it with working hex file from other hashboard.

Check this guide from here repair a T9 + after a bad firmware (lost chain)This guide may work well too in S9.
member
Activity: 119
Merit: 10
October 17, 2018, 08:50:26 PM
#10
Are you using an air conditioner to cool the intake air?  80 degrees Celsius doesn’t make sense with the air restriction and running 3 boards.

no, I don't use.



Does it help us find the error? (kernel log)

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000303] ps7-ttc #0 at f0006000, irq=43
[    0.000613] Console: colour dummy device 80x30
[    0.000650] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.100252] pid_max: default: 32768 minimum: 301
[    0.100476] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.100498] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.102654] CPU: Testing write buffer coherency: ok
[    0.102999] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.103059] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.103281] L310 cache controller enabled
[    0.103300] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.181033] CPU1: Booted secondary processor
[    0.270228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.270358] Brought up 2 CPUs
[    0.270377] SMP: Total of 2 processors activated.
[    0.270386] CPU: All CPU(s) started in SVC mode.
[    0.271032] devtmpfs: initialized
[    0.273441] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.274639] regulator-dummy: no parameters
[    0.282332] NET: Registered protocol family 16
[    0.284629] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.286897] cpuidle: using governor ladder
[    0.286910] cpuidle: using governor menu
[    0.294301] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.295811] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.295825] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.295941] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.317331] bio: create slab at 0
[    0.318725] vgaarb: loaded
[    0.319412] SCSI subsystem initialized
[    0.320447] usbcore: registered new interface driver usbfs
[    0.320631] usbcore: registered new interface driver hub
[    0.320855] usbcore: registered new device driver usb
[    0.321510] media: Linux media interface: v0.10
[    0.321669] Linux video capture interface: v2.00
[    0.321906] pps_core: LinuxPPS API ver. 1 registered
[    0.321918] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.322047] PTP clock support registered
[    0.322397] EDAC MC: Ver: 3.0.0
[    0.323436] Advanced Linux Sound Architecture Driver Initialized.
[    0.326286] DMA-API: preallocated 4096 debug entries
[    0.326300] DMA-API: debugging enabled by kernel config
[    0.326379] Switched to clocksource arm_global_timer
[    0.347290] NET: Registered protocol family 2
[    0.347933] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.348028] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.348187] TCP: Hash tables configured (established 8192 bind 8192)
[    0.348255] TCP: reno registered
[    0.348273] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.348322] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.348588] NET: Registered protocol family 1
[    0.348909] RPC: Registered named UNIX socket transport module.
[    0.348921] RPC: Registered udp transport module.
[    0.348929] RPC: Registered tcp transport module.
[    0.348937] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.348950] PCI: CLS 0 bytes, default 64
[    0.349387] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.351363] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.352736] bounce pool size: 64 pages
[    0.353661] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.353857] msgmni has been set to 1486
[    0.354625] io scheduler noop registered
[    0.354638] io scheduler deadline registered
[    0.354678] io scheduler cfq registered (default)
[    0.366847] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.366868] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.488815] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.061636] console [ttyPS0] enabled
[    1.065919] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.073557] [drm] Initialized drm 1.1.0 20060810
[    1.090505] brd: module loaded
[    1.099878] loop: module loaded
[    1.109400] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.115148] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.123215] libphy: XEMACPS mii bus: probed
[    1.127791] ------------- phy_id = 0x3625e62
[    1.132531] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.141271] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.147971] ehci-pci: EHCI PCI platform driver
[    1.155188] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.162006] usbcore: registered new interface driver usb-storage
[    1.168892] mousedev: PS/2 mouse device common for all mice
[    1.175027] i2c /dev entries driver
[    1.181929] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.187472] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.193344] Xilinx Zynq CpuIdle Driver started
[    1.198243] sdhci: Secure Digital Host Controller Interface driver
[    1.204335] sdhci: Copyright(c) Pierre Ossman
[    1.208743] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.215471] mmc0: no vqmmc regulator found
[    1.219512] mmc0: no vmmc regulator found
[    1.256397] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.265070] usbcore: registered new interface driver usbhid
[    1.270579] usbhid: USB HID core driver
[    1.275298] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.281592] nand: Micron MT29F2G08ABAEAWP
[    1.285565] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.291510] Bad block table found at page 131008, version 0x01
[    1.297725] Bad block table found at page 130944, version 0x01
[    1.303777] 3 ofpart partitions found on MTD device pl353-nand
[    1.309542] Creating 3 MTD partitions on "pl353-nand":
[    1.314647] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.322714] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.330022] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.338960] TCP: cubic registered
[    1.342195] NET: Registered protocol family 17
[    1.346931] Registering SWP/SWPB emulation handler
[    1.352824] regulator-dummy: disabling
[    1.357142] UBI: attaching mtd1 to ubi0
[    1.883909] UBI: scanning is finished
[    1.895500] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.902583] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.909346] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.916010] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.922888] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.928869] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.935976] UBI: max/mean erase counter: 8777/6249, WL threshold: 4096, image sequence number: 1984962504
[    1.945539] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.954755] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.954761] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.958731] ALSA device list:
[    1.958734]   No soundcards found.
[    1.975096] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    2.004245] UBIFS: recovery needed
[    2.090832] UBIFS: recovery completed
[    2.094496] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.100446] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.109551] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.119440] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.124470] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 56FDF5FA-8D29-4AA7-95D4-1C2E28C7C4E9, small LPT model
[    2.135996] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.143419] devtmpfs: mounted
[    2.146558] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.988741] random: dd urandom read with 0 bits of entropy available
[    3.376417]
[    3.376417] bcm54xx_config_init
[    3.986408]
[    3.986408] bcm54xx_config_init
[    7.987253] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.993344] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   24.238447] In axi fpga driver!
[   24.241521] request_mem_region OK!
[   24.244912] AXI fpga dev virtual address is 0xf01fe000
[   24.250066] *base_vir_addr = 0x8c510
[   24.265130] In fpga mem driver!
[   24.268517] request_mem_region OK!
[   24.272058] fpga mem virtual address is 0xf3000000
[   25.035656]
[   25.035656] bcm54xx_config_init
[   25.665576]
[   25.665576] bcm54xx_config_init
[   29.665944] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   29.671960] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  103.276047] UBI: scrubbed PEB 12 (LEB 0:2), data moved to PEB 1136
[  406.741880] random: nonblocking pool is initialized
Detect 1GB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=650 Chain[5] voltage_pic=108 value=880
Fix freq=650 Chain[6] voltage_pic=108 value=880
Fix freq=650 Chain[7] voltage_pic=108 value=880
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
Chain[J6] has no freq in PIC, set default freq=650M
Chain[J6] has no core num in PIC
Chain[J7] has no freq in PIC, set default freq=650M
Chain[J7] has no core num in PIC

Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:5 max freq=650
Chain:5 min freq=650

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:6 max freq=650
Chain:6 min freq=650

max freq = 650
set baud=1
Chain[J6] PIC temp offset=62,-5,0,0,0,0,34,0
Chain[J6] chip[244] use PIC middle temp offset=-5 typeID=55
New offset Chain[5] chip[244] local:35 remote:39 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J6] chip[132] use PIC middle temp offset=0 typeID=00
Warning: Chain[J6] has no temp offset in PIC! will fix it
New offset Chain[5] chip[244] local:35 remote:39 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,-3,0,0,0,0,33,0
Chain[J7] chip[244] use PIC middle temp offset=-3 typeID=55
New offset Chain[6] chip[244] local:33 remote:35 offset:28
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J7] chip[128] use PIC middle temp offset=0 typeID=00
Warning: Chain[J7] has no temp offset in PIC! will fix it
New offset Chain[6] chip[244] local:33 remote:35 offset:28
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J6] set working voltage=880 [108]
Chain[J7] set working voltage=880 [108]
setStartTimePoint total_tv_start_sys=94 total_tv_end_sys=95
restartNum = 2 , auto-reinit enabled...
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
Fatal Error: network connection lost!
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=72.3430 Asic[02]=78.6850 Asic[03]=75.7820 Asic[04]=76.6380 Asic[05]=69.3400 Asic[06]=74.5910 Asic[07]=75.1780 Asic[08]=74.8430
Asic[09]=78.3320 Asic[10]=70.5140 Asic[11]=72.5780 Asic[12]=74.0210 Asic[13]=71.5710 Asic[14]=77.4100 Asic[15]=78.9700 Asic[16]=72.5270
Asic[17]=76.2860 Asic[18]=74.6920 Asic[19]=75.4800 Asic[20]=74.0040 Asic[21]=72.1920 Asic[22]=74.4740 Asic[23]=77.2420 Asic[24]=78.3830
Asic[25]=76.4530 Asic[26]=73.6680 Asic[27]=74.7420 Asic[28]=76.6380 Asic[29]=70.0440 Asic[30]=72.4440 Asic[31]=74.5570 Asic[32]=68.8360
Asic[33]=68.7860 Asic[34]=75.8330 Asic[35]=76.5370 Asic[36]=70.5980 Asic[37]=73.6180 Asic[38]=72.9800 Asic[39]=79.3730 Asic[40]=77.1580
Asic[41]=75.5310 Asic[42]=74.8760 Asic[43]=71.2190 Asic[44]=72.8290 Asic[45]=72.6110 Asic[46]=76.4200 Asic[47]=80.0940 Asic[48]=71.5210
Asic[49]=72.4940 Asic[50]=71.5880 Asic[51]=70.5310 Asic[52]=73.2820 Asic[53]=73.0640 Asic[54]=69.5240 Asic[55]=73.5000 Asic[56]=75.1610
Asic[57]=76.8390 Asic[58]=78.0300 Asic[59]=75.5640 Asic[60]=75.3960 Asic[61]=67.3600 Asic[62]=67.0240 Asic[63]=73.3490

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=80.2110 Asic[02]=78.0640 Asic[03]=70.8830 Asic[04]=71.6210 Asic[05]=74.0210 Asic[06]=70.8660 Asic[07]=72.3930 Asic[08]=75.1780
Asic[09]=74.0540 Asic[10]=76.6880 Asic[11]=75.8490 Asic[12]=75.2790 Asic[13]=71.8230 Asic[14]=70.6320 Asic[15]=75.9160 Asic[16]=74.9770
Asic[17]=72.4100 Asic[18]=69.9940 Asic[19]=74.4230 Asic[20]=74.2550 Asic[21]=79.8420 Asic[22]=77.4100 Asic[23]=75.0270 Asic[24]=71.5040
Asic[25]=72.5950 Asic[26]=80.3460 Asic[27]=74.4740 Asic[28]=78.7520 Asic[29]=72.3090 Asic[30]=71.0340 Asic[31]=75.5310 Asic[32]=71.8060
Asic[33]=71.2190 Asic[34]=75.8490 Asic[35]=72.5440 Asic[36]=70.6320 Asic[37]=76.9400 Asic[38]=71.6550 Asic[39]=73.9700 Asic[40]=71.0680
Asic[41]=74.4570 Asic[42]=77.8290 Asic[43]=78.2320 Asic[44]=71.3030 Asic[45]=72.8630 Asic[46]=78.5500 Asic[47]=73.2990 Asic[48]=70.5980
Asic[49]=69.9270 Asic[50]=71.9070 Asic[51]=72.9800 Asic[52]=75.1950 Asic[53]=74.9430 Asic[54]=76.4360 Asic[55]=71.0510 Asic[56]=75.7650
Asic[57]=72.3760 Asic[58]=72.0740 Asic[59]=69.5580 Asic[60]=66.7060 Asic[61]=74.4740 Asic[62]=74.3390 Asic[63]=86.3180
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
Chain[5] Chip[62] local Temp=74
Chain[5] Chip[62] middle Temp=83
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=28
Chain[6] Chip[62] local Temp=68
Chain[6] Chip[62] middle Temp=77
Done read temp on Chain[6]
set FAN speed according to: temp_highest=83 temp_top1[PWM_T]=83 temp_top1[TEMP_POS_LOCAL]=74 temp_change=-1 fix_fan_steps=0
FAN PWM: 100
read_temp_func Done!
CRC error counter=0
member
Activity: 113
Merit: 31
October 16, 2018, 09:16:35 AM
#9
Are you using an air conditioner to cool the intake air?  80 degrees Celsius doesn’t make sense with the air restriction and running 3 boards.
member
Activity: 119
Merit: 10
October 16, 2018, 05:52:44 AM
#8
the temperature was no more than 80 degrees.
member
Activity: 113
Merit: 31
October 16, 2018, 12:50:22 AM
#7
https://www.ebay.com/itm/Antminer-S1-S3-S5-S7-S9-T9-D3-L3-Fan-Duct-Cooling-Shroud-6-Inch/163303439279?hash=item2605a4bbaf:g:StcAAOSwEMdbYO1U

Use with:
https://www.lowes.com/pd/Lambro-6-in-x-96-in-Aluminum-Semi-Rigid-Flexible-Duct/3240913
Or
https://www.lowes.com/pd/Lambro-6-in-x-300-in-Foil-Flexible-Duct/3319766

Six inch flexible ducting versus the four inch that you are using.  You don’t need the adapter because the six inch ducting will fit over the antminer fan.



I just realized that maybe it would be easier if I said to use a larger diameter ducting.  150 mm instead of 100 mm.
member
Activity: 119
Merit: 10
October 15, 2018, 10:06:21 PM
#6
Just a few questions:
Are you using a modified bmminer?  And are all your miners on 4” flexible tubing?  If yes to both then you should be underclocking your miners while using 4” tubing.  If you have to use flexible tubing you should be using 6” tubing because 4” is too restrictive especially with longer runs.

Yes modified bmminer but did not overclock.(the same problem in the original bmminer ) .  ""  6” "" Can't understand, can you explain? My English is bad, I'm sorry. I'm waiting for your help
member
Activity: 113
Merit: 31
October 15, 2018, 06:36:12 PM
#5
I'm using 880 volts.
power : https://i.hizliresim.com/k6N5nm.jpg

I'm waiting for your help , thank you

Just a few questions:
Are you using a modified bmminer?  And are all your miners on 4” flexible tubing?  If yes to both then you should be underclocking your miners while using 4” tubing.  If you have to use flexible tubing you should be using 6” tubing because 4” is too restrictive especially with longer runs.
hero member
Activity: 1610
Merit: 538
I'm in BTC XTC
October 15, 2018, 12:22:11 PM
#4
What Power supply are you using, and at what input voltage.  No pic needed.

Edit-I hope you didn't mean to type 880Watts psu, for that would be too small to fully power an S9...
member
Activity: 119
Merit: 10
October 15, 2018, 12:16:58 PM
#3
I'm using 880 volts.
power : https://i.hizliresim.com/k6N5nm.jpg

I'm waiting for your help , thank you
hero member
Activity: 1610
Merit: 538
I'm in BTC XTC
October 15, 2018, 10:41:56 AM
#2
What power supplies are you using, and with what input voltage?

...and you should move this to the Mining Support section, too.
member
Activity: 119
Merit: 10
October 15, 2018, 08:25:37 AM
#1
1 s9 devices  https://prnt.sc/l4zvwl
4 s9 devicez  https://prnt.sc/l4zw68

5 devices have been broken in 1 week. All devices have a single chip failure. Waiting for your help.
Jump to: