repair a T9 + after a bad firmware (lost chain)

KTzMg

newbie

Activity: 3

Merit: 0

Guys clean hashboard Completely and try to write hex file sometimes its Sometimes it answers

thierry4wd

sr. member

Activity: 446

Merit: 347

this is part of the strange errors, which I also had, check all the parameters! chip model in particular ... and try again several times,

I had the same problem, after 2 or 3 or 4 tries, it worked without changing anything ... strange but that's how it's happening;)

charcousse

newbie

Activity: 1

Merit: 0

hola amigo saludos desde acá desde Venezuela... estoy tratando de reparar una t9+ con problemas en placa DSPIC32 y hago exactamente lo que tu explicas paso a paso pero me sale el siguiente error.......

The target circuit may require more power than the debug tool can provide. An external power supply might be necessary.
Connection Failed.

Shocked

como puedo solucionarlo gracias de antemano

KTzMg

newbie

Activity: 3

Merit: 0

i try it but there is no diffrent

thierry4wd

sr. member

Activity: 446

Merit: 347

Hi, try 3,50V

KTzMg

newbie

Activity: 3

Merit: 0

hi guys
i have 6 T9+ hashboard and all of them have PIC problem

when i try to write hex file i get this error
Too much current has been drawn on VDD. Please disconnect your circuit, check the CLK and DATA lines for shorts and then reconnect.

what should i do with this problem ? i try disconnect and then reconnect

when i try to do read verify or anything like that get this or just failed

when i try to do this work with ok hashboard there is no problem and anything work correctly

my power settings 3.25 circuit from tool

i very need help

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

Quote from: Animas on April 14, 2021, 01:39:53 PM

hi guys. is there any option other than flashing the pic with the pickit3?

If you are looking for another way to write on that digital signal controller or wherever the hex file resides then the short answer is NO, if it's not pickit3 then it has to be another similar tool, but your problem might be solved using another method, post your issue in a sperate thread and you might get some answers.

Animas

newbie

Activity: 1

Merit: 0

hi guys. is there any option other than flashing the pic with the pickit3?

milani1387

newbie

Activity: 20

Merit: 4

hi. thanks for t9 hex file uploading.

thierry4wd

sr. member

Activity: 446

Merit: 347

if you can read the HEX file, you can WRITE this on bad hashboard !!! Cool

Ps : i have edited my first post with corrected the bitmain source code for never problem with this pic program Wink

milani1387

newbie

Activity: 20

Merit: 4

thanks
i i have tnm 5000 prgrammer
i can read hex file from hashboards succesfully.

thierry4wd

sr. member

Activity: 446

Merit: 347

hi, you find this on good working hashboard ...

Sorry i don't have it on my and at this time

milani1387

newbie

Activity: 20

Merit: 4

hi
i have s9 v4.21 hashboards ...
pic ic need programmed
where can i find pic hex file Huh

thanks

alvinke

newbie

Activity: 3

Merit: 0

Quote from: thierry4wd on December 14, 2018, 03:48:57 PM

I repeat it there is an error in the source code of bitmain for the T9 +...

what is error in detail you say? are you have solution?

I compiled self-firmware use link: https://github.com/bitmaintech/S9_makepackage for antminer T9+ and S9, then flashing self-firmware to T9+/S9, both T9+ and S9 lost chain. even though I flash to offical firmware through sd card recovery, miners lost chain yet.

Logs:

Code:

main.c:14097: Miner Type = T9+
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 18
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x03000f06
driver-bitmain.c:1907: Find hashboard on Chain[1]
driver-bitmain.c:1907: Find hashboard on Chain[2]
driver-bitmain.c:1907: Find hashboard on Chain[8]
driver-bitmain.c:1907: Find hashboard on Chain[9]
driver-bitmain.c:1907: Find hashboard on Chain[10]
driver-bitmain.c:1907: Find hashboard on Chain[11]
main.c:2126: chain[1] PIC jump to app
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
main.c:2134: Check chain[1] PIC fw version=0xff
main.c:2126: chain[2] PIC jump to app
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
main.c:2134: Check chain[2] PIC fw version=0xff
main.c:8651: Chain[1] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8665: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:9148: chain[1] has no freq in PIC! Will use default freq=550 and jump over...

romeorex

newbie

Activity: 1

Merit: 0

Hello, can this be done with pickit 2? Thank you.

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

Quote from: Ortadan on July 06, 2019, 07:32:53 PM

can still be an update error? or are already physical failures in the hashboard

It could be anything, but if I had to bet one BTC on it, i would say the 3 hash boards are physically damaged.

Did the seller say the hash boards were running fine? Anyhow you still havn't informed us whether you did try the latest firmware or not?

Ortadan

newbie

Activity: 13

Merit: 0

Thank you for responding, connect each hashboard individually and no hash lifts.

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000309] ps7-ttc #0 at f0006000, irq=43
[    0.000616] Console: colour dummy device 80x30
[    0.000653] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040209] pid_max: default: 32768 minimum: 301
[    0.040430] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040452] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042579] CPU: Testing write buffer coherency: ok
[    0.042925] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042986] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043213] L310 cache controller enabled
[    0.043232] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121036] CPU1: Booted secondary processor
[    0.210229] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210359] Brought up 2 CPUs
[    0.210378] SMP: Total of 2 processors activated.
[    0.210387] CPU: All CPU(s) started in SVC mode.
[    0.211040] devtmpfs: initialized
[    0.213443] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214645] regulator-dummy: no parameters
[    0.222336] NET: Registered protocol family 16
[    0.224633] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226908] cpuidle: using governor ladder
[    0.226922] cpuidle: using governor menu
[    0.234345] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235865] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235878] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235993] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.257536] bio: create slab  at 0
[    0.258945] vgaarb: loaded
[    0.259632] SCSI subsystem initialized
[    0.260668] usbcore: registered new interface driver usbfs
[    0.260847] usbcore: registered new interface driver hub
[    0.261102] usbcore: registered new device driver usb
[    0.261632] media: Linux media interface: v0.10
[    0.261789] Linux video capture interface: v2.00
[    0.262027] pps_core: LinuxPPS API ver. 1 registered
[    0.262039] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.262168] PTP clock support registered
[    0.262524] EDAC MC: Ver: 3.0.0
[    0.263571] Advanced Linux Sound Architecture Driver Initialized.
[    0.266420] DMA-API: preallocated 4096 debug entries
[    0.266434] DMA-API: debugging enabled by kernel config
[    0.266507] Switched to clocksource arm_global_timer
[    0.287048] NET: Registered protocol family 2
[    0.287716] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.287811] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.287971] TCP: Hash tables configured (established 8192 bind 8192)
[    0.288032] TCP: reno registered
[    0.288051] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.288104] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.288368] NET: Registered protocol family 1
[    0.288728] RPC: Registered named UNIX socket transport module.
[    0.288742] RPC: Registered udp transport module.
[    0.288750] RPC: Registered tcp transport module.
[    0.288759] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288772] PCI: CLS 0 bytes, default 64
[    0.289219] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291238] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292650] bounce pool size: 64 pages
[    0.293545] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293746] msgmni has been set to 1486
[    0.294532] io scheduler noop registered
[    0.294545] io scheduler deadline registered
[    0.294586] io scheduler cfq registered (default)
[    0.307197] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.307218] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.431138] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.003846] console [ttyPS0] enabled
[    1.008118] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.015733] [drm] Initialized drm 1.1.0 20060810
[    1.032773] brd: module loaded
[    1.042163] loop: module loaded
[    1.051773] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.057595] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.065330] libphy: XEMACPS mii bus: probed
[    1.069878] ------------- phy_id = 0x3625e62
[    1.074610] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.083338] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.089995] ehci-pci: EHCI PCI platform driver
[    1.097228] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.104020] usbcore: registered new interface driver usb-storage
[    1.110888] mousedev: PS/2 mouse device common for all mice
[    1.116993] i2c /dev entries driver
[    1.123926] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.129485] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.135368] Xilinx Zynq CpuIdle Driver started
[    1.140236] sdhci: Secure Digital Host Controller Interface driver
[    1.146328] sdhci: Copyright(c) Pierre Ossman
[    1.150709] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.157485] mmc0: no vqmmc regulator found
[    1.161496] mmc0: no vmmc regulator found
[    1.206545] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.215229] usbcore: registered new interface driver usbhid
[    1.220747] usbhid: USB HID core driver
[    1.225457] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.231757] nand: Micron MT29F2G08ABAEAWP
[    1.235727] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.241684] Bad block table found at page 131008, version 0x01
[    1.247940] Bad block table found at page 130944, version 0x01
[    1.253988] 3 ofpart partitions found on MTD device pl353-nand
[    1.259759] Creating 3 MTD partitions on "pl353-nand":
[    1.264861] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.272924] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.280259] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.289197] TCP: cubic registered
[    1.292434] NET: Registered protocol family 17
[    1.297157] Registering SWP/SWPB emulation handler
[    1.303085] regulator-dummy: disabling
[    1.307485] UBI: attaching mtd1 to ubi0
[    1.833879] UBI: scanning is finished
[    1.845495] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.852571] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.859334] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.865998] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.872875] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.878856] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.885963] UBI: max/mean erase counter: 17/9, WL threshold: 4096, image sequence number: 248547359
[    1.895007] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.904222] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.904227] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.908166] ALSA device list:
[    1.908170]   No soundcards found.
[    1.924553] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.953559] UBIFS: recovery needed
[    2.187888] UBIFS: recovery completed
[    2.191570] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.197519] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.206626] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.216515] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.221544] UBIFS: media format: w4/r0 (latest is w4/r0), UUID D5E65D66-FDFF-460C-B3DB-A1F2DEB908D8, small LPT model
[    2.232853] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.240045] devtmpfs: mounted
[    2.243146] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.091434] random: dd urandom read with 0 bits of entropy available
[    3.486534] 
[    3.486534] bcm54xx_config_init
[    4.096520] 
[    4.096520] bcm54xx_config_init
[    8.097396] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    8.103487] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   24.221126] In axi fpga driver!
[   24.224217] request_mem_region OK!
[   24.227647] AXI fpga dev virtual address is 0xf01fe000
[   24.232697] *base_vir_addr = 0xc510
[   24.248356] In fpga mem driver!
[   24.251429] request_mem_region OK!
[   24.254995] fpga mem virtual address is 0xf3000000
[   25.055937] 
[   25.055937] bcm54xx_config_init
[   25.685885] 
[   25.685885] bcm54xx_config_init
[   29.686329] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   29.692346] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=8000c510
miner ID : 81444d227075885c
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x06003c0c
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[2]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[2]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[2]! try again...
chain[2] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]! try again...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=1 on chain[2], value=930
get PIC voltage=1 on chain[3], value=930
get PIC voltage=1 on chain[10], value=930
get PIC voltage=1 on chain[11], value=930
get PIC voltage=1 on chain[12], value=930
get PIC voltage=1 on chain[13], value=930
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
set_reset_allhashboard = 0x00000000
chain[10] temp offset record: 1,5,0,0,0,0,33,28
chain[10] temp chip I2C addr=0x98
chain[12] temp offset record: 1,3,0,0,0,0,33,28
chain[12] temp chip I2C addr=0x98
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 6, total chain num = 6 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1389 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 17 18:17:49 CST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 81444d227075885c
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
Checking fans!get fan[5] speed=4560
get fan[2] speed=4440
get fan[5] speed=4560
get fan[2] speed=4440
get fan[5] speed=4560
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
chain[2] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J3] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

Chain[J4] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J3] orignal chain_voltage_pic=1 value=930
Chain[J3] will use backup chain_voltage_pic=870 [11]
Chain[J3] get working chain_voltage_pic=11
Chain[J4] orignal chain_voltage_pic=1 value=930
Chain[J4] will use backup chain_voltage_pic=870 [11]
Chain[J4] get working chain_voltage_pic=11
Chain[J11] orignal chain_voltage_pic=1 value=930
Chain[J11] will use backup chain_voltage_pic=870 [11]
Chain[J11] get working chain_voltage_pic=11
Chain[J12] orignal chain_voltage_pic=1 value=930
Chain[J12] will use backup chain_voltage_pic=870 [11]
Chain[J12] get working chain_voltage_pic=11
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J3] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
do heat board 8xPatten for 1 times
setStartTimePoint total_tv_start_sys=252 total_tv_end_sys=253
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=1

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000302] ps7-ttc #0 at f0006000, irq=43
[    0.000611] Console: colour dummy device 80x30
[    0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040208] pid_max: default: 32768 minimum: 301
[    0.040429] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040451] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042571] CPU: Testing write buffer coherency: ok
[    0.042922] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042981] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043206] L310 cache controller enabled
[    0.043225] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121031] CPU1: Booted secondary processor
[    0.210226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210357] Brought up 2 CPUs
[    0.210376] SMP: Total of 2 processors activated.
[    0.210384] CPU: All CPU(s) started in SVC mode.
[    0.211038] devtmpfs: initialized
[    0.213441] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214648] regulator-dummy: no parameters
[    0.222343] NET: Registered protocol family 16
[    0.224633] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226907] cpuidle: using governor ladder
[    0.226921] cpuidle: using governor menu
[    0.234353] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235869] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235883] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235997] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.257531] bio: create slab  at 0
[    0.258945] vgaarb: loaded
[    0.259641] SCSI subsystem initialized
[    0.260699] usbcore: registered new interface driver usbfs
[    0.260872] usbcore: registered new interface driver hub
[    0.261124] usbcore: registered new device driver usb
[    0.261655] media: Linux media interface: v0.10
[    0.261812] Linux video capture interface: v2.00
[    0.262060] pps_core: LinuxPPS API ver. 1 registered
[    0.262072] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.262195] PTP clock support registered
[    0.262556] EDAC MC: Ver: 3.0.0
[    0.263601] Advanced Linux Sound Architecture Driver Initialized.
[    0.266443] DMA-API: preallocated 4096 debug entries
[    0.266456] DMA-API: debugging enabled by kernel config
[    0.266536] Switched to clocksource arm_global_timer
[    0.287117] NET: Registered protocol family 2
[    0.287761] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.287856] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.288015] TCP: Hash tables configured (established 8192 bind 8192)
[    0.288076] TCP: reno registered
[    0.288095] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.288147] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.288413] NET: Registered protocol family 1
[    0.288723] RPC: Registered named UNIX socket transport module.
[    0.288735] RPC: Registered udp transport module.
[    0.288744] RPC: Registered tcp transport module.
[    0.288752] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288764] PCI: CLS 0 bytes, default 64
[    0.289203] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291229] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292617] bounce pool size: 64 pages
[    0.293537] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293731] msgmni has been set to 1486
[    0.294502] io scheduler noop registered
[    0.294516] io scheduler deadline registered
[    0.294554] io scheduler cfq registered (default)
[    0.308477] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.308498] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.433037] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.006101] console [ttyPS0] enabled
[    1.010397] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.018072] [drm] Initialized drm 1.1.0 20060810
[    1.034963] brd: module loaded
[    1.044358] loop: module loaded
[    1.053786] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.059750] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.067493] libphy: XEMACPS mii bus: probed
[    1.071862] ------------- phy_id = 0x3625e62
[    1.076775] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.085410] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.092201] ehci-pci: EHCI PCI platform driver
[    1.099457] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.106254] usbcore: registered new interface driver usb-storage
[    1.113201] mousedev: PS/2 mouse device common for all mice
[    1.119358] i2c /dev entries driver
[    1.126265] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.131785] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.137719] Xilinx Zynq CpuIdle Driver started
[    1.142556] sdhci: Secure Digital Host Controller Interface driver
[    1.148678] sdhci: Copyright(c) Pierre Ossman
[    1.152993] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.159885] mmc0: no vqmmc regulator found
[    1.163898] mmc0: no vmmc regulator found
[    1.206557] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.215256] usbcore: registered new interface driver usbhid
[    1.220760] usbhid: USB HID core driver
[    1.225479] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.231773] nand: Micron MT29F2G08ABAEAWP
[    1.235742] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.241677] Bad block table found at page 131008, version 0x01
[    1.247898] Bad block table found at page 130944, version 0x01
[    1.253952] 3 ofpart partitions found on MTD device pl353-nand
[    1.259737] Creating 3 MTD partitions on "pl353-nand":
[    1.264824] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.272879] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.280195] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.289142] TCP: cubic registered
[    1.292380] NET: Registered protocol family 17
[    1.297095] Registering SWP/SWPB emulation handler
[    1.302989] regulator-dummy: disabling
[    1.307328] UBI: attaching mtd1 to ubi0
[    1.833699] UBI: scanning is finished
[    1.845340] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.852423] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.859185] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.865848] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.872726] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.878707] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.885814] UBI: max/mean erase counter: 17/9, WL threshold: 4096, image sequence number: 248547359
[    1.894857] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.904074] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.904079] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.908036] ALSA device list:
[    1.908040]   No soundcards found.
[    1.924446] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.953592] UBIFS: recovery needed
[    2.088314] UBIFS: recovery completed
[    2.091994] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.097946] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.107047] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.116935] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.121965] UBIFS: media format: w4/r0 (latest is w4/r0), UUID D5E65D66-FDFF-460C-B3DB-A1F2DEB908D8, small LPT model
[    2.133261] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.140449] devtmpfs: mounted
[    2.143552] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.986842] random: dd urandom read with 0 bits of entropy available
[    3.376569] 
[    3.376569] bcm54xx_config_init
[    3.986579] 
[    3.986579] bcm54xx_config_init
[    7.987410] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.993500] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   22.201415] In axi fpga driver!
[   22.204480] request_mem_region OK!
[   22.207901] AXI fpga dev virtual address is 0xf01fe000
[   22.212978] *base_vir_addr = 0xc510
[   22.228456] In fpga mem driver!
[   22.231528] request_mem_region OK!
[   22.235094] fpga mem virtual address is 0xf3000000
[   23.025951] 
[   23.025951] bcm54xx_config_init
[   23.655907] 
[   23.655907] bcm54xx_config_init
[   27.656357] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   27.662379] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=8000c510
miner ID : 81444d227075885c
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x06003c0c
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[2]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[2]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[2]! try again...
chain[2] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]! try again...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
dsPIC33EP16GS202_reset_pic failed on Chain[3]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[3]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[3]! try again...
chain[3] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[3]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[3]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[3]! try again...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
Check chain[3] PIC fw version=0xff
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=1 on chain[2], value=930
get PIC voltage=1 on chain[3], value=930
get PIC voltage=1 on chain[10], value=930
get PIC voltage=1 on chain[11], value=930
get PIC voltage=1 on chain[12], value=930
get PIC voltage=1 on chain[13], value=930
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
set_reset_allhashboard = 0x00000000
chain[10] temp offset record: 1,5,0,0,0,0,33,28
chain[10] temp chip I2C addr=0x98
chain[12] temp offset record: 1,3,0,0,0,0,33,28
chain[12] temp chip I2C addr=0x98
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 6, total chain num = 6 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 2329 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 17 18:17:49 CST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 81444d227075885c
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[3]!
dsPIC33EP16GS202_reset_pic failed on Chain[3]!
dsPIC33EP16GS202_reset_pic failed on Chain[3]!
Checking fans!get fan[5] speed=4440
get fan[2] speed=4320
get fan[5] speed=4440
get fan[2] speed=4320
get fan[5] speed=4440
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
chain[2] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
dsPIC33EP16GS202_reset_pic failed on Chain[3]!
dsPIC33EP16GS202_reset_pic failed on Chain[3]!
dsPIC33EP16GS202_reset_pic failed on Chain[3]!
chain[3] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[3]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[3]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
Check chain[3] PIC fw version=0xff
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J3] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

Chain[J4] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[3]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[3]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[3]!

Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J3] orignal chain_voltage_pic=1 value=930
Chain[J3] will use backup chain_voltage_pic=870 [11]
Chain[J3] get working chain_voltage_pic=11
Chain[J4] orignal chain_voltage_pic=1 value=930
Chain[J4] will use backup chain_voltage_pic=870 [11]
Chain[J4] get working chain_voltage_pic=11
Chain[J11] orignal chain_voltage_pic=1 value=930
Chain[J11] will use backup chain_voltage_pic=870 [11]
Chain[J11] get working chain_voltage_pic=11
Chain[J12] orignal chain_voltage_pic=1 value=930
Chain[J12] will use backup chain_voltage_pic=870 [11]
Chain[J12] get working chain_voltage_pic=11
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J3] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
do heat board 8xPatten for 1 times
setStartTimePoint total_tv_start_sys=315 total_tv_end_sys=316
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

the 3 have the same fault, I do not raise the 3rd log by the limit of 64000 characters, I bought this equipment at about $ 30 to have spare fan and controller card but I noticed that the 3 hashboard presented the same error and I assumed that they updated the firmware and something went wrong.

I'm from Venezuela, I know it's an old equipment but as you know the energy is free I have other miners of this model and I try changing the controller card and still have the same fault.

can still be an update error? or are already physical failures in the hashboard.

WhyFhy

hero member

Activity: 1439

Merit: 513

Ive had the same problem I went with the newest firmware by bitmain and started at -2 THS and got all oooo's and my chains all show up with hash
I have not gotten braiins to work on T9+ , I think mikey might be reffering to "T1" or possibly T9 (not "+")

try the new firmware, start at the lowest common denominator witch is -2TH if that works walk it up slowly babysitting hash for at least 4-6 hours every step up .

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

This part

Code:

Chain[J2] has 0 asic
Chain[J3] has 0 asic
Chain[J4] has 0 asic
Chain[J9] has 0 asic
Chain[J10] has 0 asic
Chain[J11] has 0 asic
Chain[J12] has 0 asic
Chain[J13] has 0 asic
Chain[J14] has 0 asic

non of the hash boards is working, which is very strange to be honest, usually they don't all go bad at the same time, you should first try a couple of resets and firmware upgrades, try Braiins OS it works on T9 as well.

your chances with replacing the hex using pickit3 are pretty slim to nothing, I wouldn't waste the money on a T9 given the tiny chance you have with these.

however, if you do own other miners and might re-use the pickit3, go for it.

I have personally bought one, tried it on a couple of bad S9 boards and was only lucky in a ratio of say 1 to 10.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Well you tried all three when you did the log above.

Try first board all alone. Ie no psu to boards 2 and 3.

Then save log to show us.

Next try board 2 all alone
Save log to show us.

Last try board 3 all alone
Save long to show us.

Then post the logs for all three boards.

Some times problems are with 1 board
And it run the 2 other boards.

You may have 2 good boards.

Topic: repair a T9 + after a bad firmware (lost chain) (Read 22782 times)