Topic: 7970 MAXIMUM KH/S ONLY 600???? *****1000 DOGECOIN REWARD**** - page 3. (Read 6207 times)
I think your card may be too hot, do not trust your sensor completly, set your fan speed to 100% and see if the hashrate increase
OP, do this... 
Having the "shaders" value at 0 means that it will default to whatever the native value would be for the GPU so changing that won't do anything.
OP; What is the exact model number on the sticker on the back of your GPU? It should look something like FX-797A-**** If it has a V1.0, 2.0 or 5.0 list that too.
I would say you might need to flash a new BIOS to your card but getting ~600 is higher than most people(including myself) get without a BIOS flash. This tells me that you have a setting issue. If you tell me the model number I can help tweak it.
OP; What is the exact model number on the sticker on the back of your GPU? It should look something like FX-797A-**** If it has a V1.0, 2.0 or 5.0 list that too.
I would say you might need to flash a new BIOS to your card but getting ~600 is higher than most people(including myself) get without a BIOS flash. This tells me that you have a setting issue. If you tell me the model number I can help tweak it.
PN: 299-1E208-000SA and SKU#21197-00
in GPU-Z is says REV: N/A so i guess its 1.0??? Many thanks in advance for help!!
Having the "shaders" value at 0 means that it will default to whatever the native value would be for the GPU so changing that won't do anything.
OP; What is the exact model number on the sticker on the back of your GPU? It should look something like FX-797A-**** If it has a V1.0, 2.0 or 5.0 list that too.
I would say you might need to flash a new BIOS to your card but getting ~600 is higher than most people(including myself) get without a BIOS flash. This tells me that you have a setting issue. If you tell me the model number I can help tweak it.
OP; What is the exact model number on the sticker on the back of your GPU? It should look something like FX-797A-**** If it has a V1.0, 2.0 or 5.0 list that too.
I would say you might need to flash a new BIOS to your card but getting ~600 is higher than most people(including myself) get without a BIOS flash. This tells me that you have a setting issue. If you tell me the model number I can help tweak it.
are your "g" command set on 1 or 2? if it is 2 set it on 1
you will set the bat file with:
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
sgminer.exe -o stratum+tcp://xxxxxxxxx -u xxxxx -p xxxxx -I 13 -g 1 -w 256 --thread-concurrency 22528 --auto-fan --gpu-memclock 1500 --gpu-engine 1110 --gpu-powertune 20 --lookup-gap 2
before to start this setup, look on your sgminer or cgminer folder and delete the .bin files (like this: scrypt130511Thaitilg2tc20480w256l4.bin)
try several tc value, choice the highest your card start
dont forget that command "lookup-gap" is a comand who work with memory, so for high results, set it to 1.
if you undervolt your card and try to find best result saving more power possible, set lookup-gap 2
this setup is alredy overclocked, dont overclock over again.
how is voltage of card? stock voltage? or it is undervolted? use the software "gpu-z" for have it.
you will set the bat file with:
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
sgminer.exe -o stratum+tcp://xxxxxxxxx -u xxxxx -p xxxxx -I 13 -g 1 -w 256 --thread-concurrency 22528 --auto-fan --gpu-memclock 1500 --gpu-engine 1110 --gpu-powertune 20 --lookup-gap 2
before to start this setup, look on your sgminer or cgminer folder and delete the .bin files (like this: scrypt130511Thaitilg2tc20480w256l4.bin)
try several tc value, choice the highest your card start
dont forget that command "lookup-gap" is a comand who work with memory, so for high results, set it to 1.
if you undervolt your card and try to find best result saving more power possible, set lookup-gap 2
this setup is alredy overclocked, dont overclock over again.
how is voltage of card? stock voltage? or it is undervolted? use the software "gpu-z" for have it.
the -g command sets how many threads are used, and the results from 1 and 2 threads are above, I have tried many different TC settings,the best for my setup are 8192 and 20400. lookup gap 2 is the highest performance and thats what ive set it to. stock voltage
are your "g" command set on 1 or 2? if it is 2 set it on 1
you will set the bat file with:
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
sgminer.exe -o stratum+tcp://xxxxxxxxx -u xxxxx -p xxxxx -I 13 -g 1 -w 256 --thread-concurrency 22528 --auto-fan --gpu-memclock 1500 --gpu-engine 1110 --gpu-powertune 20 --lookup-gap 2
before to start this setup, look on your sgminer or cgminer folder and delete the .bin files (like this: scrypt130511Thaitilg2tc20480w256l4.bin)
try several tc value, choice the highest your card start
dont forget that command "lookup-gap" is a comand who work with memory, so for high results, set it to 1.
if you undervolt your card and try to find best result saving more power possible, set lookup-gap 2
this setup is alredy overclocked, dont overclock over again.
how is voltage of card? stock voltage? or it is undervolted? use the software "gpu-z" for have it.
you will set the bat file with:
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
sgminer.exe -o stratum+tcp://xxxxxxxxx -u xxxxx -p xxxxx -I 13 -g 1 -w 256 --thread-concurrency 22528 --auto-fan --gpu-memclock 1500 --gpu-engine 1110 --gpu-powertune 20 --lookup-gap 2
before to start this setup, look on your sgminer or cgminer folder and delete the .bin files (like this: scrypt130511Thaitilg2tc20480w256l4.bin)
try several tc value, choice the highest your card start
dont forget that command "lookup-gap" is a comand who work with memory, so for high results, set it to 1.
if you undervolt your card and try to find best result saving more power possible, set lookup-gap 2
this setup is alredy overclocked, dont overclock over again.
how is voltage of card? stock voltage? or it is undervolted? use the software "gpu-z" for have it.
use sgminer 4.0.0
i13
lookup gap 2
tc 8192
powertune 20
engine clock at stock
mem clock at stock
1 find better tc your card start. (multiple of 2048)
2 find high mem your card work (1500 often is a good deal, but card can work over 1800)
3 find high engine your card work (start about 60% of mem value and add 5 per time, good deal are engine = 0.70*memclock)
4 set intensity.
sgminer, works better than cgminer, it is based on cgminer but fixed for only script minig.
only this, can improve your hashrate, after start you only have to find your best setting for best performance in hashrate or in hs/W (if power is not cheap).
if you can, post your batfile and results.
i13
lookup gap 2
tc 8192
powertune 20
engine clock at stock
mem clock at stock
1 find better tc your card start. (multiple of 2048)
2 find high mem your card work (1500 often is a good deal, but card can work over 1800)
3 find high engine your card work (start about 60% of mem value and add 5 per time, good deal are engine = 0.70*memclock)
4 set intensity.
sgminer, works better than cgminer, it is based on cgminer but fixed for only script minig.
only this, can improve your hashrate, after start you only have to find your best setting for best performance in hashrate or in hs/W (if power is not cheap).
if you can, post your batfile and results.
tried sgminer 4.0, gives the same exact performance as cgminer with my setup. With a TC of 8192 im able to push the mem clock to 1500 stable. and engine clock to 1125, I havent found any 'sweet spots' when overclocking (5mhz increments). increasing the intensity over 13 results in lower khs and HW errors. Increasing the TC above 8192 lowers my khs until i hit a TC of 20400
with a TC of 8192, 1500mem and 1125 gpu im getting 595khs, (all other settings are same as in first post)
How are you determining your thread concurrency? From my experience, higher concurrency is not better for these cards. Try removing the concurrency line from your .conf file, deleting your bat file and seeing what it defaults to. That will give you a good starting point for where you should be.
Your clock speeds need some tweaking. Your core clock is a bit high and your mem clock is a bit low. Try something like 1040 core clock and 1500 mem clock and see where that gets you. These cards can be massively overclocked with few hardware errors but they do get hot so make sure your ventilation is good.
Try it with:
core clock - 1040
mem clock - 1500
intensity - 13
gpu threads - 2
thread concurrency - 8192
everything else the same as you have currently and report back.
Your clock speeds need some tweaking. Your core clock is a bit high and your mem clock is a bit low. Try something like 1040 core clock and 1500 mem clock and see where that gets you. These cards can be massively overclocked with few hardware errors but they do get hot so make sure your ventilation is good.
Try it with:
core clock - 1040
mem clock - 1500
intensity - 13
gpu threads - 2
thread concurrency - 8192
everything else the same as you have currently and report back.
I tried your settings, im getting around 550khs with an intensity of 14, I 13 is around the 450 khs. (first time i have ever seen an increase in khs with an intensity above 13) I 15 gives HW errors
How are you determining your thread concurrency? From my experience, higher concurrency is not better for these cards. Try removing the concurrency line from your .conf file, deleting your bat file and seeing what it defaults to. That will give you a good starting point for where you should be.
Your clock speeds need some tweaking. Your core clock is a bit high and your mem clock is a bit low. Try something like 1040 core clock and 1500 mem clock and see where that gets you. These cards can be massively overclocked with few hardware errors but they do get hot so make sure your ventilation is good.
Try it with:
core clock - 1040
mem clock - 1500
intensity - 13
gpu threads - 2
thread concurrency - 8192
everything else the same as you have currently and report back.
Your clock speeds need some tweaking. Your core clock is a bit high and your mem clock is a bit low. Try something like 1040 core clock and 1500 mem clock and see where that gets you. These cards can be massively overclocked with few hardware errors but they do get hot so make sure your ventilation is good.
Try it with:
core clock - 1040
mem clock - 1500
intensity - 13
gpu threads - 2
thread concurrency - 8192
everything else the same as you have currently and report back.
use sgminer 4.0.0
i13
lookup gap 2
tc 8192
powertune 20
engine clock at stock
mem clock at stock
1 find better tc your card start. (multiple of 2048)
2 find high mem your card work (1500 often is a good deal, but card can work over 1800)
3 find high engine your card work (start about 60% of mem value and add 5 per time, good deal are engine = 0.70*memclock)
4 set intensity.
sgminer, works better than cgminer, it is based on cgminer but fixed for only script minig.
only this, can improve your hashrate, after start you only have to find your best setting for best performance in hashrate or in hs/W (if power is not cheap).
if you can, post your batfile and results.
i13
lookup gap 2
tc 8192
powertune 20
engine clock at stock
mem clock at stock
1 find better tc your card start. (multiple of 2048)
2 find high mem your card work (1500 often is a good deal, but card can work over 1800)
3 find high engine your card work (start about 60% of mem value and add 5 per time, good deal are engine = 0.70*memclock)
4 set intensity.
sgminer, works better than cgminer, it is based on cgminer but fixed for only script minig.
only this, can improve your hashrate, after start you only have to find your best setting for best performance in hashrate or in hs/W (if power is not cheap).
if you can, post your batfile and results.
Hey guys,
I have a sapphire 7970 and I just cant get this thing above 600kh/s
Ive tried everything i can think of. First person that suggests something that gets my 7970 over 650kh/s ill give you 1000 dogecoins!! 
I know this card has more to give, whenever ive tuned other cards to their max you start to notice abit of system lag, but Ive never experienced any lag with my 7970.
as soon as I change any of the following my kh/s drops alot.
higher thread concurrency,
lower thread concurrency,
more than 1 thread,
higher intensity,
lower intensity,
increase memory clock,
increase gpu clock,
temps are always good and VRM's arent getting hot either
im using CGminer 3.7.2 on windows 7 x64 sp1
currant settings:
"intensity" : "13",
"vectors" : "1",
"worksize" : "256",
"kernel" : "scrypt",
"lookup-gap" : "2",
"thread-concurrency" : "20400",
"shaders" : "0",
"gpu-engine" : "1150",
"gpu-fan" : "65-65",
"gpu-memclock" : "1375",
"gpu-memdiff" : "0",
"gpu-powertune" : "20",
"gpu-vddc" : "0.000",
"temp-cutoff" : "92",
"temp-overheat" : "86",
"temp-target" : "80",
"api-mcast-port" : "4028",
"api-port" : "4028",
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "1",
"hotplug" : "5",
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "30",
"scrypt" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"
Any help tuning this would be much appreciated!!!
I have a sapphire 7970 and I just cant get this thing above 600kh/s
Ive tried everything i can think of. First person that suggests something that gets my 7970 over 650kh/s ill give you 1000 dogecoins!! I know this card has more to give, whenever ive tuned other cards to their max you start to notice abit of system lag, but Ive never experienced any lag with my 7970.
as soon as I change any of the following my kh/s drops alot.
higher thread concurrency,
lower thread concurrency,
more than 1 thread,
higher intensity,
lower intensity,
increase memory clock,
increase gpu clock,
temps are always good and VRM's arent getting hot either
im using CGminer 3.7.2 on windows 7 x64 sp1
currant settings:
"intensity" : "13",
"vectors" : "1",
"worksize" : "256",
"kernel" : "scrypt",
"lookup-gap" : "2",
"thread-concurrency" : "20400",
"shaders" : "0",
"gpu-engine" : "1150",
"gpu-fan" : "65-65",
"gpu-memclock" : "1375",
"gpu-memdiff" : "0",
"gpu-powertune" : "20",
"gpu-vddc" : "0.000",
"temp-cutoff" : "92",
"temp-overheat" : "86",
"temp-target" : "80",
"api-mcast-port" : "4028",
"api-port" : "4028",
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "1",
"hotplug" : "5",
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "30",
"scrypt" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"
Any help tuning this would be much appreciated!!!
Jump to: