Topic: [ANN] ccminer 2.3 - opensource - GPL (tpruvot) - page 32. (Read 500193 times)

HERE IS A SIMPLE LAUNCH LINE FOR KOMODO (KMD)--

Komodo is an Equihash coin on YIIMP.  Here is the launch file:

======

:loop

ccminer -a equihash -o stratum+tcp://yiimp.ccminer.org:2142 -u RLz5eeiuwDi7nz7owbMButBz8rCMZPbxb4 -p c=KMD,d=32 --cpu-priority=3

pause
goto loop

======

For Windows, place the loop in a batch file.  Do not include the cut lines.  For a Linux BASH script, remove the loop statements and simply include the single launch line.    Be sure to place your own address in the line after the "-u".        --scryptr

388.31 drivers gave only half Neoscrypt hashrate with alexis 1.0 cuda 7.5 ccminer. Rolled back to 384.94 and everything is perfect again (1350 kh/s for 1070)

I am not sure if I should try it or not because my rig is just running perfectly stable and I dont want to risk that........

who knows how to configure ccminer for equihash?

YES--

Read the Readme.  Set the algorithm and point it at a pool, like YIIMP.  If the cards perform well, make Intensity or clock adjustments.       --scryptr

I would also like to know this - anyone tried the new drivers out and would like to share his/her experience?

My mining rig is running with the Nvidia driver version 384.xx..... Did anyone upgrade to version 388? Any speed changes (positive or negative)?

Will this work to mine BTX using a 5x1070 Nvidia and Ubuntu 16.04?
Thanks for your reply.

I am a micro miner, one GPU card in my desktop computer, and no programmer, just an "end consumer".  I am using the precompiled windows 64 version of ccminer 2.2.2 from GitHub.  The miner works, but I am unable to increase the intensity level when scrypt mining.  No matter what intensity I set in the command line using the -i function, no matter where in the command line I put the -i function, and even though it initially assigns more threads, it then reverts to a different (?default) intensity a few lines down. My gpu doesn't even warm up, and the hash rate is low.  Rather than overclocking my GPU, I would prefer to increase the intensity so that it works harder.  How do I get it to actually run with the intensity settings I want? This is what I see:


D:\ccminer-x64-2.2.2-cuda9>ccminer-x64 -a scrypt -o stratum+tcp://us.multipool.us:XXX -u theXXX.1 -p XXX -i 14.99

*** ccminer 2.2.2 for nVidia GPUs by tpruvot@github ***
Built with VC++ 2013 and nVidia CUDA SDK 9.0 64-bits
Originally based on Christian Buchner and Christian H. project
Include some kernels from alexis78, djm34, djEzo, tsiv and krnlx.

BTC donation address: 1AJdfCpLWPNoAMDfHF1wD5y8VgKSSTHxPo (tpruvot)

[2017-11-08 06:34:23] Adding 16128 threads to intensity 14, 32512 cuda threads
[2017-11-08 06:34:23] Starting on stratum+tcp://us.multipool.us:XXX
[2017-11-08 06:34:23] NVML GPU monitoring enabled.
[2017-11-08 06:34:23] NVAPI GPU monitoring enabled.
[2017-11-08 06:34:23] 1 miner thread started, using 'scrypt' algorithm.
[2017-11-08 06:34:24] Stratum difficulty set to 131072 (2.00000)
[2017-11-08 06:34:24] scrypt block 1631827, diff 10898.083
[2017-11-08 06:34:25] GPU #0: 32 hashes / 4.0 MB per warp.
[2017-11-08 06:34:26] GPU #0: Performing auto-tuning, please wait 2 minutes...
[2017-11-08 06:34:26] GPU #0: maximum total warps (BxW): 1484
[2017-11-08 06:34:45] Stratum difficulty set to 256 (0.00391)
[2017-11-08 06:34:45] scrypt block 1631828, diff 8720.082
[2017-11-08 06:35:09] scrypt block 1631829, diff 8720.082
[2017-11-08 06:36:47] GPU #0: 589791.16 hash/s with configuration T12x11
[2017-11-08 06:39:34] scrypt block 1631830, diff 8720.082
[2017-11-08 06:39:34] GPU #0: using launch configuration T12x11
[2017-11-08 06:39:34] scrypt block 1631831, diff 8720.082
[2017-11-08 06:39:34] GPU #0: Intensity set to 12.0313, 4224 cuda threads
[2017-11-08 06:39:34] scrypt factor set to 9 (1024)

I XXX'd out the actual pool, worker name, password, but you can see where I attempted to set the intensity to 14.99 in the command line, was assigned extra threads, then lower down the intensity was changed to 12.0313 with only a fraction of the threads.  I have also tried with setting the T levels myself in advance, so that the auto-tuning does not occur, same result. Any help would be appreciated.  Thank you in advance.