Topic: [ANN] NiceHash.com - sell & buy hash rate cloud mining service / multipool - page 288. (Read 794394 times)
June 19, 2014, 02:17:02 PM
It works for everyone automatically, but it only changes extremely low or extremely high diffs. Usually, if setting correct d, you won't even notice it.
June 19, 2014, 02:16:50 PM
how do we test the vardiff? just make our password "X"?
The vardiff is working regardless of what you use in the password section. I have a diff= setting in the password and it works as the initial vardiff, but then soon changes depending on how well or poorly my mining is working.
June 19, 2014, 01:54:42 PM
how do we test the vardiff? just make our password "X"?
June 19, 2014, 09:02:59 AM
We have implemented a test version of vardiff. Please let us know if you notice anything strange with your miners. Thank you.
June 19, 2014, 04:17:39 AM
i can't put order for 0.05 GH/s speed !?
what the fuck, yesterday it was OK, i wasted my hashrate, since Mineral pool are limited to 50 MH/s and we are in rush hour before PoW end, don't u see there are a lot of 0.05 GH/s customer on the list !
NOT a happy customer ! move back to betarigs
what the fuck, yesterday it was OK, i wasted my hashrate, since Mineral pool are limited to 50 MH/s and we are in rush hour before PoW end, don't u see there are a lot of 0.05 GH/s customer on the list !
NOT a happy customer ! move back to betarigs
ME TOO !!!
Sorry for that. Our wallet is slow (as you could notice when trying to place an order or view balance) so we temporary took some measures against placing many small limited orders. We had no idea that there are coins that limit hashing speed.
Bottom limit is back to 0.05 on X11 and X13 for now.
June 19, 2014, 02:27:57 AM
There are Problems with the Website? CloudFlare Security check?
June 19, 2014, 12:46:47 AM
Hi guys, I've been troubled by "Share above target" for few days already and still can't find the root source of the issue despite Googling and searching in this thread. :/
I'm using sgminer-5.0-pre-release-2014-06-11 and password set to d=0.04 for X11 and X13, d=256 for ScrypN.
Only Scrypt on port 3333 works. even Keccak doesn't work.
I'm using sgminer-5.0-pre-release-2014-06-11 and password set to d=0.04 for X11 and X13, d=256 for ScrypN.
Only Scrypt on port 3333 works. even Keccak doesn't work.
same. also losing connection to nicehash, and getting 50% share rejected
June 18, 2014, 10:07:56 PM
Hi guys, I've been troubled by "Share above target" for few days already and still can't find the root source of the issue despite Googling and searching in this thread. :/
I'm using sgminer-5.0-pre-release-2014-06-11 and password set to d=0.04 for X11 and X13, d=256 for ScrypN.
Only Scrypt on port 3333 works. even Keccak doesn't work.
I'm using sgminer-5.0-pre-release-2014-06-11 and password set to d=0.04 for X11 and X13, d=256 for ScrypN.
Only Scrypt on port 3333 works. even Keccak doesn't work.
June 18, 2014, 03:54:24 PM
Quote
•Pool deaths and order cancellations are penalized with 5 seconds worth of mining. Penalties go to the miners working on that order.
Should be 5 minutes. too many users using unstable pools in my opinion 
June 18, 2014, 12:59:26 PM
i can't put order for 0.05 GH/s speed !?
what the fuck, yesterday it was OK, i wasted my hashrate, since Mineral pool are limited to 50 MH/s and we are in rush hour before PoW end, don't u see there are a lot of 0.05 GH/s customer on the list !
NOT a happy customer ! move back to betarigs
what the fuck, yesterday it was OK, i wasted my hashrate, since Mineral pool are limited to 50 MH/s and we are in rush hour before PoW end, don't u see there are a lot of 0.05 GH/s customer on the list !
NOT a happy customer ! move back to betarigs
ME TOO !!!
June 18, 2014, 11:41:36 AM
i can't put order for 0.05 GH/s speed !?
what the fuck, yesterday it was OK, i wasted my hashrate, since Mineral pool are limited to 50 MH/s and we are in rush hour before PoW end, don't u see there are a lot of 0.05 GH/s customer on the list !
NOT a happy customer ! move back to betarigs
what the fuck, yesterday it was OK, i wasted my hashrate, since Mineral pool are limited to 50 MH/s and we are in rush hour before PoW end, don't u see there are a lot of 0.05 GH/s customer on the list !
NOT a happy customer ! move back to betarigs
June 18, 2014, 10:39:36 AM
VERY FUNNY.... Just noticed you changed the website to .1 !!! Don't bother answering my prior post !!! NOT A HAPPY CUSTOMER ..
June 18, 2014, 10:29:49 AM
I just placed 1 order for limited GH/s of .05, they were excepted THEN I noticed they were assigned a .10 GH/s and were eating through my $$ at TWICE the rate I had contracted for !!! CAN'T change the rate on the order screen, it won't accept anything less than .10 - I then created another order at .05 and the SAME deal !!! What's up 
False advertizing !! (PS - It was OK yesterday - what's changed and WHY ) !!!
False advertizing !! (PS - It was OK yesterday - what's changed and WHY ) !!! 
June 18, 2014, 10:22:02 AM
why do my rigs can't connect to x11 and x13 servers ? i tried all port : 4337,3337,4336,3336
Yep, trying to get a new rig up and am having the same issue. 
June 18, 2014, 09:36:41 AM
Tyvm FIY, I have 50 rigs 3x290, my total hashrate ~500MH, I'm using d=0.01 now, if I only mine x11 and x13 then do you have any suggest which diff should I set?
You should adjust difficulty for each separate miner (rig), that said, if you have multiple rigs, each rig with 3x R9 290 that makes about 10Mhs for X11 per rig, and if you look at this table this results in a suggested diff d=0.08. Even if you're mining with several rigs at the same BTC address, you should set diff for each separate rig, not for the combined hashing power of all rigs.
June 18, 2014, 09:18:30 AM
Would be nice if past orders groups by pool url && pool port && pool username && pool password.
So instead of 10 little orders without date and pagination, I'll be able to find how much did I spent for certain pool
So instead of 10 little orders without date and pagination, I'll be able to find how much did I spent for certain pool
June 18, 2014, 08:49:30 AM
Should be fine now for all miners that couldn't connect.
We have raised minimal difficulties for both providers and buyers. Providers can now use diff 128 or higher for scrypt, nscrypt, sha256 and keccak, 0.04 or higher for x11 and x13.
Buyers have to use pools that support min diff 32 for scrypt, nscrypt, sha256 and keccak. We are in era of fast ASIC and it is simply unacceptable for pools to still have so low difficulties (imagine how many diff 32 shares a 80MH/s scrypt ASIC sends, if one simple 500KH/s card can already produce 1 share per 10 seconds). If your favorite pool does not support higher diffs, we suggest you to contact them and explain that they are loosing important money on fees that they could gain when just increasing their diff (which is one setting in config file).
We have raised minimal difficulties for both providers and buyers. Providers can now use diff 128 or higher for scrypt, nscrypt, sha256 and keccak, 0.04 or higher for x11 and x13.
Buyers have to use pools that support min diff 32 for scrypt, nscrypt, sha256 and keccak. We are in era of fast ASIC and it is simply unacceptable for pools to still have so low difficulties (imagine how many diff 32 shares a 80MH/s scrypt ASIC sends, if one simple 500KH/s card can already produce 1 share per 10 seconds). If your favorite pool does not support higher diffs, we suggest you to contact them and explain that they are loosing important money on fees that they could gain when just increasing their diff (which is one setting in config file).
We are now running with higher difficulty until the problem is discovered and resolved.
Is there something wrong with the difficulty? Ever since the problems with the X11/X13 yesterday, my difficulty settings are being ignored. I've set d=0.01 but difficulty stays at 0.04.
I've tried changing my difficulty but it stays at 0.04.
I've tried changing my difficulty but it stays at 0.04.
There are no ASICs for x11 and x13 so as I understand it was not an explanation for these algos...
Could you answer pls when it will be solved for X11 (X13)?
Thanks.
June 18, 2014, 07:56:43 AM
Important! You should set appropriate difficulty for your miner to increase efficiency and reduce the number of submitted shares that produces rejects. If you have fast miner that is capable of creating masses of rejects at short time, then set higher difficulty so the reject count is lower, otherwise your miner might get banned by our overload prevention system. One thing to remember is that difficulty doesn't affect earnings. Higher difficulties will result in lower bandwidth and less frequent shares submission. You can set the difficulty of your miner by setting d= within your password parameter to one of the following values: https://www.nicehash.com/index.jsp?p=faq#faqs7
Tyvm FIY, I have 50 rigs 3x290, my total hashrate ~500MH, I'm using d=0.01 now, if I only mine x11 and x13 then do you have any suggest which diff should I set?
June 18, 2014, 07:43:22 AM
Important! You should set appropriate difficulty for your miner to increase efficiency and reduce the number of submitted shares that produces rejects. If you have fast miner that is capable of creating masses of rejects at short time, then set higher difficulty so the reject count is lower, otherwise your miner might get banned by our overload prevention system. One thing to remember is that difficulty doesn't affect earnings. Higher difficulties will result in lower bandwidth and less frequent shares submission. You can set the difficulty of your miner by setting d= within your password parameter to one of the following values: https://www.nicehash.com/index.jsp?p=faq#faqs7
June 18, 2014, 07:22:09 AM
Hi
This is my first try with Nicehash but I'm having problems contributing SHA-256 hashing
I am using Windows 7 and bfgminer 3.10.0 or 4.0.0 (makes no difference)
I just get a constant stream of -
"Stratum from pool 0 requested work update" alternating with "Rejected untracked stratum share from pool 0"
Is it me or something poolside?
This is my first try with Nicehash but I'm having problems contributing SHA-256 hashing
I am using Windows 7 and bfgminer 3.10.0 or 4.0.0 (makes no difference)
I just get a constant stream of -
"Stratum from pool 0 requested work update" alternating with "Rejected untracked stratum share from pool 0"
Is it me or something poolside?
Jump to: