All I can refer to is Awesome's info on it http://www.awesomeminer.com/help/minerapi.aspx
hum... but to use this features on Awesomw Miner i need to pay 100$.
no open source utility???
Topic: Antminer S7/S9 scheduled clock speed adjust (Read 3161 times)
hum... but to use this features on Awesomw Miner i need to pay 100$.
no open source utility???
All I can refer to is Awesome's info on it http://www.awesomeminer.com/help/minerapi.aspx
S9 - remove the A: , enable the W:
but after a reboot, S9 will revert to Restricted again. ---> @patrike, not sure if you are aware of this
easier solution for noobs on the S7, flash older version of fw such as Fri Dec 11 11:51:56 CST 2015, no restrictions.
GL & have fun, don't break, blow or brick anything !
Just looked into the Restricted API access and speed changes using Awesome Miner: You need either the Professional Edition or higher to use those functions. Looks like time for me to bite the bullet and upgrade from Standard to Premium (good for 20miners per-site).but after a reboot, S9 will revert to Restricted again. ---> @patrike, not sure if you are aware of this
easier solution for noobs on the S7, flash older version of fw such as Fri Dec 11 11:51:56 CST 2015, no restrictions.
GL & have fun, don't break, blow or brick anything !
Nice thing is that Premium also unlocks remote access for monitoring/rebooting my farm at work
hi not fuzzy warm.
but there is no API on firmware, to manage rules from custom c#/VB.NET code and interact with S7/S9?
i find nothing about that...
but it seems impossible!!!
S9 - remove the A: , enable the W:
but after a reboot, S9 will revert to Restricted again. ---> @patrike, not sure if you are aware of this
easier solution for noobs on the S7, flash older version of fw such as Fri Dec 11 11:51:56 CST 2015, no restrictions.
GL & have fun, don't break, blow or brick anything !
Just looked into the Restricted API access and speed changes using Awesome Miner: You need either the Professional Edition or higher to use those functions. Looks like time for me to bite the bullet and upgrade from Standard to Premium (good for 20miners per-site).but after a reboot, S9 will revert to Restricted again. ---> @patrike, not sure if you are aware of this
easier solution for noobs on the S7, flash older version of fw such as Fri Dec 11 11:51:56 CST 2015, no restrictions.
GL & have fun, don't break, blow or brick anything !
Nice thing is that Premium also unlocks remote access for monitoring/rebooting my farm at work
warning to anyone considering buying an S9 or any miner from Bitmain.
They might send you a broken machine and then refuse to repair or replace it.
That's what they have just done to me.
I have spent over $14,000 USD with them and they treat me like a piece of dog sh*te they scraped off their shoe.
Well F**K You Bitmain. Thanks for nothing.
They might send you a broken machine and then refuse to repair or replace it.
That's what they have just done to me.
I have spent over $14,000 USD with them and they treat me like a piece of dog sh*te they scraped off their shoe.
Well F**K You Bitmain. Thanks for nothing.
S9 - remove the A: , enable the W:
but after a reboot, S9 will revert to Restricted again. ---> @patrike, not sure if you are aware of this
easier solution for noobs on the S7, flash older version of fw such as Fri Dec 11 11:51:56 CST 2015, no restrictions.
GL & have fun, don't break, blow or brick anything !
but after a reboot, S9 will revert to Restricted again. ---> @patrike, not sure if you are aware of this
easier solution for noobs on the S7, flash older version of fw such as Fri Dec 11 11:51:56 CST 2015, no restrictions.
GL & have fun, don't break, blow or brick anything !
I believe that you can also set up a cron job by ssh that runs a script to run the miner as needed each time of the day.
I have personally done it with Spondoolies SP30 with little effort.
Just so ya know -- some s7's and all s9's operate in a restricted (vs Privilaged) API/SSH access mode... All operating data can be read but not all can be changed & saved outside of using Bitmain's GUI.I have personally done it with Spondoolies SP30 with little effort.
My s7 b18 is one of them. M's Miner Monitor simply does not see it and I believe one from an earlier batch is the same. It also has never seen the s9's and since that program has been abandoned, that leaves Awesome Miner Monitor.
Finally pointed Awesome at the s7 batch 18, yep. It sees it and reports it as restricted access.
Gotta change that and the website for Awesome has some info on it http://www.awesomeminer.com/help/minerapi.aspx
but.....
a) does the privilege hack work for the s9?
b) what 'ux is Bitmain using? What editor is in it? What are the edit commands...
c) What is the file to be changed and where is it located?
Simply follow these instructions to let Awesome Miner configure the Privileged API access for all your Antminer's:
http://www.awesomeminer.com/help/antminerapi.aspx
It's a very boring and time consuming task to manually configure this over SSH on all your miners. Awesome Miner can setup this for you on all Antminer's at once.
I believe that you can also set up a cron job by ssh that runs a script to run the miner as needed each time of the day.
I have personally done it with Spondoolies SP30 with little effort.
Just so ya know -- some s7's and all s9's operate in a restricted (vs Privilaged) API/SSH access mode... All operating data can be read but not all can be changed & saved outside of using Bitmain's GUI.I have personally done it with Spondoolies SP30 with little effort.
My s7 b18 is one of them. M's Miner Monitor simply does not see it and I believe one from an earlier batch is the same. It also has never seen the s9's and since that program has been abandoned, that leaves Awesome Miner Monitor.
Finally pointed Awesome at the s7 batch 18, yep. It sees it and reports it as restricted access.
Gotta change that and the website for Awesome has some info on it http://www.awesomeminer.com/help/minerapi.aspx
but.....
a) does the privilege hack work for the s9?
b) what 'ux is Bitmain using? What editor is in it? What are the edit commands...
c) What is the file to be changed and where is it located?
I believe that you can also set up a cron job by ssh that runs a script to run the miner as needed each time of the day.
I have personally done it with Spondoolies SP30 with little effort.
I have personally done it with Spondoolies SP30 with little effort.
Here is a guide how to set and schedule Antminer frequency changes using Awesome Miner:
http://www.awesomeminer.com/help/antmineroperations.aspx
http://www.awesomeminer.com/help/antmineroperations.aspx
is think this one:
https://bitcointalksearch.org/topic/is-there-an-app-that-can-schedule-frequency-changes-on-s7s9-thanks-anyone-1535310
https://bitcointalksearch.org/topic/is-there-an-app-that-can-schedule-frequency-changes-on-s7s9-thanks-anyone-1535310
I checked the thread, the project still seems to be in the pipeline. It doesn't look like something much will come out of it, I will keep my fingers crossed.
https://bitcointalksearch.org/topic/m.10462772
I think it will work with s9, with little modifications.
I think it will work with s9, with little modifications.
This one seems likely. But I do not know yet, how long it will last.
https://bitcointalksearch.org/topic/m.10462772
I think it will work with s9, with little modifications.
I think it will work with s9, with little modifications.
There is someone who has already developed this as far as I know. Try the mining software section of the forum.
I had the same idea, and would be more than happy if this is possible... For me it's not about noise, but temperature during day/night.
Hi!
Is there any way to schedule automatic clock speed set?
For exmaple: I would need to have quiet miner from about 7am to 9pm (450Mhz). From 9pm to 7am it can be loud.
Putty?
Is there any way to schedule automatic clock speed set?
For exmaple: I would need to have quiet miner from about 7am to 9pm (450Mhz). From 9pm to 7am it can be loud.
Putty?
Jump to: