Topic: Antminer s9 won't mine (Read 1023 times)

the problem was on pool
nicehash went down then antpool went down and i don't have third pool

How long did you let it run? Newest version of machines and firmware are reported to take 45 minutes or longer before finishing the initial boot process and normal running parameters are set. Sounds excessive, yes, but that's the way BiteMe, I mean ShitMain, oh crap, Bitmain forked up the miner software on their machines.

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc:

• 0
• 1

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]    Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000305] ps7-ttc #0 at df804000, irq=43
[    0.000613] Console: colour dummy device 80x30
[    0.000643] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040204] pid_max: default: 32768 minimum: 301
[    0.040423] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040443] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042592] CPU: Testing write buffer coherency: ok
[    0.042921] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042981] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043201] L310 cache controller enabled
[    0.043220] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121030] CPU1: Booted secondary processor
[    0.210226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210359] Brought up 2 CPUs
[    0.210377] SMP: Total of 2 processors activated.
[    0.210386] CPU: All CPU(s) started in SVC mode.
[    0.211048] devtmpfs: initialized
[    0.213468] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214680] regulator-dummy: no parameters
[    0.221902] NET: Registered protocol family 16
[    0.224094] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226388] cpuidle: using governor ladder
[    0.226400] cpuidle: using governor menu
[    0.233768] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235283] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235297] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235408] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257253] bio: create slab at 0
[    0.258659] vgaarb: loaded
[    0.259383] SCSI subsystem initialized
[    0.260606] usbcore: registered new interface driver usbfs
[    0.260807] usbcore: registered new interface driver hub
[    0.261038] usbcore: registered new device driver usb
[    0.262113] media: Linux media interface: v0.10
[    0.262272] Linux video capture interface: v2.00
[    0.262511] pps_core: LinuxPPS API ver. 1 registered
[    0.262523] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.262647] PTP clock support registered
[    0.263006] EDAC MC: Ver: 3.0.0
[    0.264048] Advanced Linux Sound Architecture Driver Initialized.
[    0.266866] DMA-API: preallocated 4096 debug entries
[    0.266879] DMA-API: debugging enabled by kernel config
[    0.266953] Switched to clocksource arm_global_timer
[    0.286913] NET: Registered protocol family 2
[    0.287633] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.287690] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.287775] TCP: Hash tables configured (established 4096 bind 4096)
[    0.287820] TCP: reno registered
[    0.287838] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.287869] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288101] NET: Registered protocol family 1
[    0.288447] RPC: Registered named UNIX socket transport module.
[    0.288459] RPC: Registered udp transport module.
[    0.288467] RPC: Registered tcp transport module.
[    0.288476] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288489] PCI: CLS 0 bytes, default 64
[    0.288921] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290963] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293058] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293259] msgmni has been set to 967
[    0.294038] io scheduler noop registered
[    0.294051] io scheduler deadline registered
[    0.294088] io scheduler cfq registered (default)
[    0.308089] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.308109] dma-pl330 f8003000.ps7-dma:    DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.432560] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.001024] console [ttyPS0] enabled
[    1.005320] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.012960] [drm] Initialized drm 1.1.0 20060810
[    1.030037] brd: module loaded
[    1.039413] loop: module loaded
[    1.049133] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.054883] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.062992] libphy: XEMACPS mii bus: probed
[    1.067553] ------------- phy_id = 0x3625e62
[    1.072295] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.080911] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.087579] ehci-pci: EHCI PCI platform driver
[    1.094785] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.101608] usbcore: registered new interface driver usb-storage
[    1.108473] mousedev: PS/2 mouse device common for all mice
[    1.114555] i2c /dev entries driver
[    1.121457] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.126935] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.132849] Xilinx Zynq CpuIdle Driver started
[    1.137750] sdhci: Secure Digital Host Controller Interface driver
[    1.143844] sdhci: Copyright(c) Pierre Ossman
[    1.148262] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.154985] mmc0: no vqmmc regulator found
[    1.159025] mmc0: no vmmc regulator found
[    1.196970] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205649] usbcore: registered new interface driver usbhid
[    1.211160] usbhid: USB HID core driver
[    1.215861] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.222160] nand: Micron MT29F2G08ABAEAWP
[    1.226125] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.232061] Bad block table found at page 131008, version 0x01
[    1.238285] Bad block table found at page 130944, version 0x01
[    1.244338] 3 ofpart partitions found on MTD device pl353-nand
[    1.250116] Creating 3 MTD partitions on "pl353-nand":
[    1.255207] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263278] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270615] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.279593] TCP: cubic registered
[    1.282832] NET: Registered protocol family 17
[    1.287544] Registering SWP/SWPB emulation handler
[    1.293420] regulator-dummy: disabling
[    1.297753] UBI: attaching mtd1 to ubi0
[    1.671186] UBI: scanning is finished
[    1.683039] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.690123] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.696866] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.703570] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.710428] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.716397] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.723528] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1411313766
[    1.732558] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.741776] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.741782] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.745708] ALSA device list:
[    1.745711]   No soundcards found.
[    1.762619] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.877608] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.883538] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.892669] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    1.902553] UBIFS: reserved for root: 0 bytes (0 KiB)
[    1.907592] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E7000DF8-CAC1-4941-A278-188D954B7F71, small LPT model
[    1.939027] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.965090] devtmpfs: mounted
[    1.968222] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.160509] random: dd urandom read with 0 bits of entropy available
[    3.787004]
[    3.787004] bcm54xx_config_init
[    4.396994]
[    4.396994] bcm54xx_config_init
[    7.397829] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.403919] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   23.320001] In axi fpga driver!
[   23.323072] request_mem_region OK!
[   23.326463] AXI fpga dev virtual address is 0xdf9fc000
[   23.331597] *base_vir_addr = 0x8c510
[   23.346837] In fpga mem driver!
[   23.350036] request_mem_region OK!
[   23.353543] fpga mem virtual address is 0xe2000000
[   24.126974]
[   24.126974] bcm54xx_config_init
[   24.756970]
[   24.756970] bcm54xx_config_init
[   27.757815] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   27.763838] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 8164b44966008854
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[17] has core num=5
Chain[5] ASIC[43] has core num=1
Chain[5] ASIC[47] has core num=15
Chain[5] ASIC[59] has core num=1
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[14] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1490 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found= 1786 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=21332 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Tue Aug 15 11:37:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 8164b44966008854
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[5] speed=4320
get fan[2] speed=5880
get fan[5] speed=4320
get fan[2] speed=5880
get fan[5] speed=4320
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=74 value=900
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
Chain[J7] orignal chain_voltage_pic=74 value=900
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
Chain[J8] orignal chain_voltage_pic=74 value=900
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[17] has core num=5
Chain[J6] ASIC[43] has core num=1
Chain[J6] ASIC[47] has core num=15
Chain[J6] ASIC[59] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[14] has core num=1
Chain[J8] has core num in PIC
miner total rate=14225GH/s fixed rate=14000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:668
Asic[ 1]:668 Asic[ 2]:668 Asic[ 3]:668 Asic[ 4]:668 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Asic[47]:668 Asic[48]:668
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668
Chain:5 max freq=668
Chain:5 min freq=668

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=662
Asic[ 0]:662
Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 Asic[ 8]:662
Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 Asic[16]:662
Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 Asic[24]:662
Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 Asic[29]:662 Asic[30]:662 Asic[31]:662 Asic[32]:662
Asic[33]:662 Asic[34]:662 Asic[35]:662 Asic[36]:662 Asic[37]:662 Asic[38]:662 Asic[39]:662 Asic[40]:662
Asic[41]:662 Asic[42]:662 Asic[43]:662 Asic[44]:662 Asic[45]:662 Asic[46]:662 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:6 max freq=662
Chain:6 min freq=662

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=662
Asic[ 0]:662
Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 Asic[ 8]:662
Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 Asic[16]:662
Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 Asic[24]:662
Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 Asic[29]:662 Asic[30]:662 Asic[31]:662 Asic[32]:662
Asic[33]:662 Asic[34]:662 Asic[35]:662 Asic[36]:662 Asic[37]:662 Asic[38]:662 Asic[39]:662 Asic[40]:662
Asic[41]:662 Asic[42]:662 Asic[43]:662 Asic[44]:662 Asic[45]:662 Asic[46]:662 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:7 max freq=662
Chain:7 min freq=662


Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:662
Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Detect a bad chip=47 on chain[5], fixed to 400M
Asic[47]:668 Asic[48]:668
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668
Chain:5 max freq=668
Chain:5 min freq=662

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=662
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:6 max freq=662
Chain:6 min freq=656

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=662
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:7 max freq=662
Chain:7 min freq=656

max freq = 668
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:33 remote:36 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:29 remote:33 offset:26
Chain[J7] chip[244] get middle temp offset=26 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:28 remote:33 offset:25
Chain[J8] chip[244] get middle temp offset=25 typeID=55
single board rate=4713 voltage limit=870 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 870
single board rate=4713 voltage limit=870 on chain[6]
get PIC voltage=870 on chain[6], check: must be < 870
single board rate=4714 voltage limit=870 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 870
Chain[J6] set working voltage=870 [125]
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
read failed, old value: Chain[5] Chip[62] local Temp=0
Chain[5] Chip[62] middle Temp=48
Special fix Chain[5] Chip[62] middle Temp = 15
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=26
read failed, old value: Chain[6] Chip[62] local Temp=0
Chain[6] Chip[62] middle Temp=44
Special fix Chain[6] Chip[62] middle Temp = 15
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=25
read failed, old value: Chain[7] Chip[62] local Temp=0
Chain[7] Chip[62] middle Temp=43
Special fix Chain[7] Chip[62] middle Temp = 15
Done read temp on Chain[7]
Set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

miner statu don't show anything even after waiting 30 min and the antminer sound is not stable sometimes it's loud and  sometimes calm down and the green light always on
http://prntscr.com/hk0soq

thats because you did a factory reset which wipes all settings and returns it to DHCP

yes, just disconnect all the power plugs AND the I/O ribbon on one hashboard and power up.

is it ok to connect the psu to only 2 hashboard and the controller pci-e ?

That's what we're trying to help you figure out.  Have you disconnected the power and I/O to one of the boards and run like that?  It really sounds like your PSU isn't supplying enough power for all 3 hashboards, run it with only 2 to help find out.

why my miner start blowing cold hair and stop hashing ?

When one of my miners changes IP I log on to my router and look for it there.  You should see it in the logs.
And, yes, the I/O cable is the ribbon cable from the controller to each hash board.

clicked on ip report and reset the miner but now i can't access it using the old ip

so is that milk there on the psu from the begining ? i didn't notice

The white stuff is silicone caulk to prevent things from rattling or vibrating.  It also acts as an insulator.  It's fine, there is no issue even if the apw was completely filled with it. 

Pour milk over the PSU to promote electron flow.

However, do NOT pour milk on the S9, as it is allergic to milk (it will break, the PSU is safe though)

Thank you but did you see that white thing on the psu ?

what is the I/O ribbon cable ?
do you mean here that i power only 2 card or what ?

I've run across this with a single card before but never the whole miner. A soft reboot usually clears it up. If that doesn't work you can try the IP Reporter reset described on the Bitmain forum page here https://enforum.bitmain.com/bbs/topics/3957

You could try disconnecting the power connections, and I/O ribbon cable, to one of the hashboards and then see how it runs.  That might help determine what is going on here.
-i.e. if it runs fine with two cards powered, no matter which two, that would point to the PSU...

no 

Do you have a multimeter and skills to measure the 12V voltage during the miner operation?