Pages:
Author

Topic: Bitmain New Miner S7-LN 2.7T @697W discussion (Not official) - page 3. (Read 23285 times)

sr. member
Activity: 324
Merit: 250
hi guys

What settings do you run these miners on I have been running mine on 700M Freq mining at around 3150 Ghs temp around 55 - 60 have pushed to 725 but brought back down on warm day what temp is too hot for these? Is someone running a higher frequency?

Interested to hear the response, I've got two S7-LN that I'd like to maximize the hashrate on. They're running stock now, got another 30 days or so left of warranty before i'm ready to crank these up.
full member
Activity: 290
Merit: 100
hi guys

What settings do you run these miners on I have been running mine on 700M Freq mining at around 3150 Ghs temp around 55 - 60 have pushed to 725 but brought back down on warm day what temp is too hot for these? Is someone running a higher frequency?
legendary
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
It probably wouldn't be stable at stock voltage, but with the right tools stock voltage isn't really a limitation. S7LN boards should cool more effectively than stock S7 boards so, as far as power and heat goes, 700MHz should work better on the LN if you get around the stock voltage.
full member
Activity: 197
Merit: 100
if i get one, whats is highest temp it can handle ?
can i overclock it to 700M ?
hero member
Activity: 773
Merit: 528
Anyone know about the temperature reading on the miner status page? Is it PCB or chip? (I suppose it is PCB, because mine is around 50-52)
legendary
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
If there's enough interest, maybe. I'm not sure there is though. The option always exists to have one direct-shipped, and I can hack it into the most efficient it'll run for a given setpoint (you decide the hashrate) and reship to you. It'd cost pretty much the same in the end.
hero member
Activity: 676
Merit: 501
Sidehack - Will u do another round of hacked S7-LN's if bitmain releases another lot??
hero member
Activity: 2534
Merit: 623
Not to worry I've managed to putty in and bring up the cgminer running (screen -r) then change the option through that. It won't be a permenant solution (won't survive reboots) but it will do for now.
hero member
Activity: 2534
Merit: 623
Hi guys,

Now ive got one of sidehacks S7LN's and would like to do balance mining across three different pools, I understand I may lose a bit of hash and errors might increase. But I cant seem to find the option on the gui. On my old S3's it had the option for Failover,Balance,Quota, but I cant seem to find this option.

Can anyone point it out or give me a way of doing this?

Thanks.
newbie
Activity: 28
Merit: 3
sr. member
Activity: 338
Merit: 250
newbie
Activity: 28
Merit: 3
Batch 2 is now available from BitmainTech for $240.

Sold out
sr. member
Activity: 338
Merit: 250
Batch 2 is now available from BitmainTech for $240.
hero member
Activity: 676
Merit: 501
ordered mine friday night, Lets see how long it takes to get to Sydney Australia..

Took a week to arrive..
legendary
Activity: 1820
Merit: 1092
~Full-Time Minter since 2016~
So what does the "LN" stand for?

i call it the "little noob"  (LN)   Grin

it's little at under 3th/s and noob friendly as it's "plug and play"   ;Wink
legendary
Activity: 1096
Merit: 1021
I think the stock PSU on mine is starting to go.  This past week the miner just went dead three times.  Each time the PSU was turned off.  Power cycling the unit would bring it back up for a few hours but then it would shut down again.  I down clocked it from 600 to 500 and it was stable for 24 hours at about 2.2th.  I have since upped it to [email protected] and knock on wood it has been running four and a half hours so far.
legendary
Activity: 3822
Merit: 2703
Evil beware: We have waffles!
Its clear that bitmain is only out to make a quick buck since its introduction of the S5. I've read nothing but bad news with all the S7's and now S9.  As a owner of S1,S3 and S5 and can say that their attention to detail after the S5 is questionable. Ofcourse what  happened after the S3 was they didn't care about the noise.
I now have an Avalon 6 and think people should switch.
Er?
I have 22 s7's starting from batch-1 of up through b18, not a bit of trouble with any of them. Ever. So far have 3 s9's running, all perform as advertised, no problems so far.

There. You have now read GOOD news on the s7 and 9's Wink
legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
mine is at my buddies office.

the two head for europe will ship out on sat.

I am testing the Finnish one first
then the GB one second.

The stock psu is no big deal.  I suggest this one:

http://www.newegg.com/Product/Product.aspx?Item=9SIA1N83U90792&cm_re=evga_850_p2-_-17-438-056-_-Product

not cheap  look for it on sale.
sr. member
Activity: 475
Merit: 265
Ooh La La, C'est Zoom!
My @sidehack S7-LN arrived today, and is happily hashing away at ~2.0 TH/s and pulling ~450W at the wall using the Bitmain Enermax PSU.

Nice work @sidehack.

Cheers,

- zed
Pages:
Jump to: