Topic: Blade heeeeeeeelp please! - page 2. (Read 1858 times)
Well the cheap PSU I bought from staples was garbage so was the WiFi Extender so instead I am going to return them and instead run some Cat5 Cable out to it's location cause I got it working on a PSU from a broken computer no problem. Then I have to change my Ip on my pc to match the same range as the blade after I get to that point.
i can help you for your setup. it's should be a minor problem.., PM me,
Best regards
Best regards
Ok I will let you know how it goes tomorrow.
Linux - you're gonna want a command prompt, and start with "man ifconfig"
Windows - find "Network Connections", right-click and hit Properties, then under IPv4 settings change it to "Use the following IP address:", type in 192.168.1.something, 255.255.255.0, and 192.168.1.1 in the IP address, subnet mask and default gateway respectively.
Make sure you remember what the setting was previously so you can put it back to how it was once the blade's IP is changed to your home network's range.
Windows - find "Network Connections", right-click and hit Properties, then under IPv4 settings change it to "Use the following IP address:", type in 192.168.1.something, 255.255.255.0, and 192.168.1.1 in the IP address, subnet mask and default gateway respectively.
Make sure you remember what the setting was previously so you can put it back to how it was once the blade's IP is changed to your home network's range.
my ip is an ip4 and it is 192.168.0.x now I need to go and figure out how to manually change my ip.
What is the IP of the computer you're using? If it's not in the 192.168.1.x range, you need to manually set it to that address range to access the blade.
Once that's done and the blade config page loads, change the blade's IP address to something in the range your computer's IP *was* set at. You can then change your computer's IP back to its previous settings and should be able to load the config page.
There's plenty of good information on this forum about setting blades up from there.
Once that's done and the blade config page loads, change the blade's IP address to something in the range your computer's IP *was* set at. You can then change your computer's IP back to its previous settings and should be able to load the config page.
There's plenty of good information on this forum about setting blades up from there.
Ok I got it connected using the other PC but when I put 192.168.1.254:8000/main into my browser it takes me to a page cannot be displayed.
I have the same computer outside it is my mothers her MOBO failed so I am going to try and use that power supply but I have to jump that as well sense the MOBO is shot. let me go give it a try and I will let you know how that goes.
It's brand new
http://s22.postimg.org/lw324z93l/DSCF6221.jpg Yes I have everything correct it just shuts down the PSU after blinking a few times.
http://postimg.org/image/j4r9yo56x/
http://s10.postimg.org/7d1xqqbx5/DSCF6218.jpg
http://s9.postimg.org/402uduz7j/DSCF6220.jpg
http://s7.postimg.org/gn4bjxsi3/DSCF6222.jpg
Wouldn't let me post right away so I had to wait.
http://s10.postimg.org/7d1xqqbx5/DSCF6218.jpg
http://s9.postimg.org/402uduz7j/DSCF6220.jpg
http://s7.postimg.org/gn4bjxsi3/DSCF6222.jpg
Wouldn't let me post right away so I had to wait.
I have read it 50 times and I have my wires plugged In the exact same way dogie does. Here are the links to the pics.
I am seriously lost I have followed the power up guide with Molex cables but yet when I connect the blade to my PSU the Blade blinks a few times then the PSU shuts down every time. I added the images of my power supply and the setup I am using. I would like to get this started as fast as possible.
I hope I added the images correctly if not you can still click on the links I believe or let me know how to do it properly but I would really greatly like to get my blade working very soon
I hope I added the images correctly if not you can still click on the links I believe or let me know how to do it properly but I would really greatly like to get my blade working very soonJump to: