[Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s) - page 129.

commonorx

newbie

Activity: 99

Merit: 0

Quote from: P00P135 on November 18, 2017, 06:58:32 PM

-S cryptonight.usa.nicehash.com:3355

or change usa to eu or asia to connect there instead.

That connection string worked.

Thanks!

P00P135

full member

Activity: 1124

Merit: 136

-S cryptonight.usa.nicehash.com:3355

or change usa to eu or asia to connect there instead.

commonorx

newbie

Activity: 99

Merit: 0

Quote from: Goldenbunip on November 17, 2017, 12:22:05 PM

Quote from: vdkcoins on November 15, 2017, 11:04:55 PM

Finally got single MSI Vega 56 to run stable with xmr-cast-vega. My key was getting the temp right <65 to stay stable and keep MEM < 950
Block chain drivers and reset driver prior to running. Very stable.

Freq: -8%
Mem: 945
Power +10
Rate: 1980
Fan: ~3400 min
Temp: 64
Ave Search 45 secs, no errors

or

Freq -8%
Mem: 935
Power +0
Rate 1950
Fan: ~2500 min
Temp: 62

Not bad, both very stable, but I have not been able to get to the fabled 2000 Wink

Here's my question. I mined 24 hrs with nicehash
Nicehash reports between 1.33 and 2.2 at any given time and is quite variable on their BTC profitability curve through the day.
anyone have good/bad NiceHash experience or can explain this phenomenon?

Or, suggest a more profitable pool to point to?

Thanks

You MEM speed is way too low to hit 2k mark, stick it to 1100 and see what you get.

Nicehhash speed on the site is calculated from your accepted share rate at the difficulty level submitted. Since there is a large amount of luck in the time between share finds, the reported rate will vary wildly. I get between 0 and 4KH on the site per vega64 running at ~2050each. Its the longer average that's important. So open the Nicehash page and select just Cryptonight and the graph has the average on it and you will see teh average which is usually more stable.

Can you share your connection setting for connecting to nicehash? I am not able to get it connected with cast xmr.

l1xx

member

Activity: 115

Merit: 10

Quote from: ?? on ??

I give up. While it initially appeared cast is better solution for me I simply cant to get it working and remain stable. On the other hand stak does the job for me just fine. Trick which worked for me was that I closed AMD settings after I set them all and then I even end process in task manager. After that it works like swiss watch 12 hours so far no drop in speed or freeze up.

Which process are you closing exactly, the host application?

Denson87

newbie

Activity: 10

Merit: 0

I tried Cast XMR on my 2 XFX Vega 56 with stock Bios but Hashrate is different. Anyone know why?
https://imgur.com/a/jwXs3

All 3 posted regs from the Guide wont work for me. How can a download the sheet to create my own? I always get error sheet protection when opening.

SergGT001

newbie

Activity: 29

Merit: 0

How to save the settings of the graphics card driver after rebooting the windows?

underdog13

newbie

Activity: 12

Merit: 0

Quote from: illanz on November 17, 2017, 08:06:22 AM

I have this exact same thing going on.

bat file like
cast_xmr-vega --opencl 0 -G 0,1,2,3,4,5,6,7 -I 9 -S xmr-us-eas

combination of 4xx and 5xx series cards totalling 8

all bios modded and running blockchain drivers

says im getting 6550 h/s on cast. Runs forever eth or etc at 234 mhs

nanopool showing good current hashrate finally

Thanks

rednoW

legendary

Activity: 1510

Merit: 1003

Seems the dev has some trip to ocean, beach, sand and palm trees. Well deserved ))

xeridea

sr. member

Activity: 449

Merit: 251

Quote from: Permonik on November 17, 2017, 10:23:28 AM

Quote from: l1xx on November 17, 2017, 09:24:18 AM

when was the last time the developer posted here?

Hi, I am not sure, couple of weeks?

https://bitcointalksearch.org/user/glph3k-1176677

16 days

c0ld_snack

newbie

Activity: 9

Merit: 0

Quote from: meroh on November 17, 2017, 09:05:59 PM

Quote from: tf2addict on November 16, 2017, 06:07:07 PM

Quote from: meroh on November 16, 2017, 05:24:14 PM

I'm running 4 Vega 56 with stock BIOS and was able to get 1950 h/s on 3 of them, but my 4th is only running at 1720 h/s. I am using block chain drivers, tried disabling and re-enabling everything and all of the cards are over clocked to the exact same settings. Anyone know of any reason why this might be happening?

What brands? I have a PowerColor (1850 H/s) and it does 100 H/s less than my GigaByte and Sapphire (1950 H/s) on the same settings.

I was using 1 MSI, 2 Gigabyte and 1 Sapphire and I just added another MSI for a total of 5 GPU. Again, 4 of them are running at 1950 H/s and 1 at 1730 H/s. I am going to have to double check exactly which GPU it is, but I would love to see 1950 all the way down the list. It might not be worth the head ache messing around with it for such a small gain.

Quote from: mikejennings on November 16, 2017, 06:22:56 PM

I have an RX 580 that generates 10% lower hashrate despite all GPU-Z readings being the same. Just a shit set of silicone.

Yeah I was thinking that might be the issue, just a slower card for some reason or another.

----

I too am experiencing the issue of when the miner runs for 4-6 hours, I will randomly get 0 H/s on 1 of the GPU and shortly after the miner will just stop.

I've run into the same problems with one of my rigs (8 Vega 64s) .. turned out that one of my GPUs was on the fringe for being weak. Had to dial back from 1100mhz to 1000mhz and up the HBM voltage to 950 and it's run for days without issue. Sometimes with it up at 1100mhz it would run for 2 hours or 36 hours without issue and then would crash the system. No rhyme or reason. To diagnose the problematic GPU I split test with multiple instances of the miner (in my case xmr-amd). 4 devices on instance 1, 4 devices on instance 2. One of the instances will lock up. Then split test those devices (6 devices on instance 1, 2 on 2), eventually it became apparent which was at fault as the miner would lock up with the other running. Couple times it would lock up at like 10 PM and run all night full steam not mining a damn thing just burning electricity... split testing eliminated that issue

meroh

newbie

Activity: 5

Merit: 0

Quote from: tf2addict on November 16, 2017, 06:07:07 PM

Quote from: meroh on November 16, 2017, 05:24:14 PM

I'm running 4 Vega 56 with stock BIOS and was able to get 1950 h/s on 3 of them, but my 4th is only running at 1720 h/s. I am using block chain drivers, tried disabling and re-enabling everything and all of the cards are over clocked to the exact same settings. Anyone know of any reason why this might be happening?

What brands? I have a PowerColor (1850 H/s) and it does 100 H/s less than my GigaByte and Sapphire (1950 H/s) on the same settings.

I was using 1 MSI, 2 Gigabyte and 1 Sapphire and I just added another MSI for a total of 5 GPU. Again, 4 of them are running at 1950 H/s and 1 at 1730 H/s. I am going to have to double check exactly which GPU it is, but I would love to see 1950 all the way down the list. It might not be worth the head ache messing around with it for such a small gain.

Quote from: mikejennings on November 16, 2017, 06:22:56 PM

I have an RX 580 that generates 10% lower hashrate despite all GPU-Z readings being the same. Just a shit set of silicone.

Yeah I was thinking that might be the issue, just a slower card for some reason or another.

----

I too am experiencing the issue of when the miner runs for 4-6 hours, I will randomly get 0 H/s on 1 of the GPU and shortly after the miner will just stop.

bulgar73

member

Activity: 128

Merit: 10

Quote from: MickDaster on November 17, 2017, 05:03:42 PM

i dont know what am i doing wrong, i simply ccan not get more than 500hs on XMR using claymore crypto miner.

What should i do to reach 1800+ hhs?

I got POWERCOLOR RX VEGA 56 8GB

https://www.reddit.com/r/MoneroMining/comments/74hjqn/monero_and_vega_the_definitive_guide/

----
BTC

MickDaster

full member

Activity: 167

Merit: 100

i dont know what am i doing wrong, i simply ccan not get more than 500hs on XMR using claymore crypto miner.

What should i do to reach 1800+ hhs?

I got POWERCOLOR RX VEGA 56 8GB

tf2addict

full member

Activity: 675

Merit: 100

I typically get around 5% outdated shares on NiceHash and between 5 and 13% on other pools. On XMR Stak I basically get 100% "good" shares. Is XMR Stak just hiding outdated shares or does Cast really do have more bad shares than Stak? 5% (let alone 13%) is a lot and negates any better hash rate vs Stak.

Goldenbunip

newbie

Activity: 18

Merit: 0

Quote from: vdkcoins on November 15, 2017, 11:04:55 PM

Finally got single MSI Vega 56 to run stable with xmr-cast-vega. My key was getting the temp right <65 to stay stable and keep MEM < 950
Block chain drivers and reset driver prior to running. Very stable.

Freq: -8%
Mem: 945
Power +10
Rate: 1980
Fan: ~3400 min
Temp: 64
Ave Search 45 secs, no errors

or

Freq -8%
Mem: 935
Power +0
Rate 1950
Fan: ~2500 min
Temp: 62

Not bad, both very stable, but I have not been able to get to the fabled 2000 Wink

Here's my question. I mined 24 hrs with nicehash
Nicehash reports between 1.33 and 2.2 at any given time and is quite variable on their BTC profitability curve through the day.
anyone have good/bad NiceHash experience or can explain this phenomenon?

Or, suggest a more profitable pool to point to?

Thanks

You MEM speed is way too low to hit 2k mark, stick it to 1100 and see what you get.

Nicehhash speed on the site is calculated from your accepted share rate at the difficulty level submitted. Since there is a large amount of luck in the time between share finds, the reported rate will vary wildly. I get between 0 and 4KH on the site per vega64 running at ~2050each. Its the longer average that's important. So open the Nicehash page and select just Cryptonight and the graph has the average on it and you will see teh average which is usually more stable.

Permonik

member

Activity: 275

Merit: 11

Quote from: l1xx on November 17, 2017, 09:24:18 AM

when was the last time the developer posted here?

Hi, I am not sure, couple of weeks?

Puffncough

newbie

Activity: 13

Merit: 0

Took me about a week to config some settings on the Vega 64 I just got but I seem to have somewhat consistent Hash rates.

1,800 - 2,000 mining to nano pool mining XMR

I know the new drivers are updated with the block chain driver but the 17.30 version that the OP has in his guide seems to work best with this miner.

I would like to set this miner to a different currency though, I'm pretty new to this and can't seem to get the correct config settings to mine ETN without it giving me a connection error. I'm guessing you just can't do it with this miner without some updates.

matrixturk

full member

Activity: 476

Merit: 100

we are waiting for simplemining system

l1xx

member

Activity: 115

Merit: 10

when was the last time the developer posted here?

ninjam

newbie

Activity: 84

Merit: 0

abnormal

Topic: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s) - page 129. (Read 206406 times)