[CLOSED] batch #39 0.25 btc per Blade, backplanes .15 - page 3.

xzempt

hero member

Activity: 504

Merit: 500

Quote from: ryanb on December 12, 2013, 07:06:45 AM

my order is still showing at the sorting facility since sat the 7th and it says i should receive my package on dec 09 and nothing showed up yet.

Any ideas what should i do?

use UPS next time? i'm in the same boat.... item dropped off on the 7th.... delivery date says dec 9, but no movement since processed at origin facility.... cant get anyone on the phone at post office.... the 1-800 number is useless.....

ryanb

legendary

Activity: 1148

Merit: 1000

my order is still showing at the sorting facility since sat the 7th and it says i should receive my package on dec 09 and nothing showed up yet.

Any ideas what should i do?

artbatista

full member

Activity: 158

Merit: 100

185f525100fa25e5fb2749070846dffe90b5674eac55421d9bb3318ea9a31037

one blade please....

aznatama

full member

Activity: 167

Merit: 100

What's your policy on DOA blades? I sent you an email.

CanaryInTheMine

donator

Activity: 2352

Merit: 1060

between a rock and a block!

orders up through today are being packed and will be dropped off shortly. thanks!

CanaryInTheMine

donator

Activity: 2352

Merit: 1060

between a rock and a block!

Quote from: sbfree on December 08, 2013, 09:21:19 AM

canary, please reserve at least 2 blades and 2 backplanes(if possible on these). I have already PM'd you, and will send btc later today, thanks, sbfree.

PMed

sbfree

sr. member

Activity: 336

Merit: 250

canary, please reserve at least 2 blades and 2 backplanes(if possible on these). I have already PM'd you, and will send btc later today, thanks, sbfree.

CanaryInTheMine

donator

Activity: 2352

Merit: 1060

between a rock and a block!

dropping off shipments. Thank you!

ryanb

legendary

Activity: 1148

Merit: 1000

4 blades + backplane all paid and label has been emailed

5d2f49250e04b6fe1f326144bc5962de736cfb456bb41a305a2a4a8e01022540

Thanks

CanaryInTheMine

donator

Activity: 2352

Merit: 1060

between a rock and a block!

today's orders have been shipped.

soy

legendary

Activity: 1428

Merit: 1013

No joy. Here it is at 12.8V:

Total MHS:   00000
Received:   0000000000
Accepted:   0000000000
Per Minute:   000.00
Efficiency:   000.00%
Up Time:   0d,00h,00m,51s

Current Server: 192.168.1.4:8332
Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
--------------------

I switch the server:

Total MHS:   00000
Received:   0000000000
Accepted:   0000000000
Per Minute:   000.00
Efficiency:   000.00%
Up Time:   0d,00h,02m,53s

Current Server: :19501
Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

I Switch the server again:

Total MHS:   00000
Received:   0000000000
Accepted:   0000000000
Per Minute:   000.00
Efficiency:   000.00%
Up Time:   0d,00h,03m,26s

Current Server: 192.168.1.4:8332
Chip: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

I've seen others report the 19501 previously.

CanaryInTheMine

donator

Activity: 2352

Merit: 1060

between a rock and a block!

Quote from: soy on December 05, 2013, 08:13:50 PM

Hi Canary,

My Blade had been running 4 days shy of three months then started acting up.

It was only giving me double digits "accepted" as viewed on the proxy for a few seconds after powering up before hashrate dropped to zero and it started rebooting. I changed power supplies. I've reconfigured the routing a number of times and my other miners are running okay so the router shouldn't be the problem.

Then the ASIC chip display changed from all "O"'s to all "x"'s. I've reset to factory defaults repeatedly, the new config showing 192.168.1.2,btcguild.com, but still all "'x"'s. Reconfiguring to my proxy's I still see no indication of requesting work. The web interface works fine.

I note that soon after getting the Blade 3 months ago I soldered a tantalum capacitor between the + & - pins at the power plug. That is fine.

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

I would almost guess it's the PIC acting up.

Any suggestions?

Thanks.

soy

as far as I know, blade modifications void the warranty. you'd need to contact here: https://bitcointalksearch.org/topic/official-asicminer-hardware-information-270573 to see what can or can not be done. I do not have instructions to replace modified blades.

soy

legendary

Activity: 1428

Merit: 1013

Quote from: aznatama on December 06, 2013, 01:42:10 PM

Quote from: soy on December 05, 2013, 08:13:50 PM

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

Any suggestions?

Thanks.

soy

Might want to give it a stable 12v... the backpane PSU provides 12.7v
If your power wires are getting hot, you're putting too much load through the power wires. Use more wires. Each 18ga wire is only rated for 2.3a worth of power transmission. That's only about 27w of power. you'll need 4 power lines if you're using 18ga wiring high quality pcie cables ise this, molex may have 20ga wiring which is only rated for about half)

Okay, will up the voltage to 12.7V. I had been running fine on 11.8V. Would make less sense to raise the voltage given the board failed because we had an exceptionally warm winter's day here in Georgia and the room went up to 76°F after weeks at low 60°'s and that even with switching supplies/buck converters, the greater the voltage difference the more power lost at the supply. But I will give it a try.

aznatama

full member

Activity: 167

Merit: 100

Quote from: soy on December 05, 2013, 08:13:50 PM

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

Any suggestions?

Thanks.

soy

Might want to give it a stable 12v... the backpane PSU provides 12.7v
If your power wires are getting hot, you're putting too much load through the power wires. Use more wires. Each 18ga wire is only rated for 2.3a worth of power transmission. That's only about 27w of power. you'll need 4 power lines if you're using 18ga wiring high quality pcie cables ise this, molex may have 20ga wiring which is only rated for about half)

Dogvomit

newbie

Activity: 4

Merit: 0

1 Hub

Date: 12/5/2013 21:17
To: CanaryInTheMine - Hub 1GGFSxxncmXdP9tUSPNPAPi4timLahH191
Debit: -0.25 BTC
Net amount: -0.25 BTC
Transaction ID: 30600110ace5de1e380e552219023f94ac42e7009bbf253a6e9510df4f443bed

ryanb

legendary

Activity: 1148

Merit: 1000

mine keeps declaring sick and i have to unplug it and plug it back and restart bfgminer

it runs for few hours and claims sick again

maybe i should get a backplane

how much a backplane and i would probably get 3 more blades if you can give me a price on them with the backplane

i purchased like 50 usb eruptors when they were 0.55 each lol i am still in pain

so take care of me please

soy

legendary

Activity: 1428

Merit: 1013

Hi Canary,

My Blade had been running 4 days shy of three months then started acting up.

It was only giving me double digits "accepted" as viewed on the proxy for a few seconds after powering up before hashrate dropped to zero and it started rebooting. I changed power supplies. I've reconfigured the routing a number of times and my other miners are running okay so the router shouldn't be the problem.

Then the ASIC chip display changed from all "O"'s to all "x"'s. I've reset to factory defaults repeatedly, the new config showing 192.168.1.2,btcguild.com, but still all "'x"'s. Reconfiguring to my proxy's I still see no indication of requesting work. The web interface works fine.

I note that soon after getting the Blade 3 months ago I soldered a tantalum capacitor between the + & - pins at the power plug. That is fine.

I measure 11.8vdc in and 1.04volts on the copper pads mid board.

I would almost guess it's the PIC acting up.

Any suggestions?

Thanks.

soy

CanaryInTheMine

donator

Activity: 2352

Merit: 1060

between a rock and a block!

Quote from: twib2 on December 04, 2013, 11:20:09 PM

Hi Canary - one blade por favor:

0754703166b569cf254b9140652b83c787549c2a79d5c28d0343bef79f786fb1
124jzM8sHhSit8LkV753KMYyWxxxxxxxxx
9406203699300xxxxxxxxx
HJhTpq6zSzc8A9NeMpM4cvZ/wZL9paWtqGVF5Ja9b13+ASWOtjbUEuyS9AH4CYmMnWPQiuQAvevlMGxxxxxxxxx=

emailing label now...

Thanks!

shipping...

twib2

sr. member

Activity: 280

Merit: 250

Helperizer

Hi Canary - one blade por favor:

0754703166b569cf254b9140652b83c787549c2a79d5c28d0343bef79f786fb1
124jzM8sHhSit8LkV753KMYyWxxxxxxxxx
9406203699300xxxxxxxxx
HJhTpq6zSzc8A9NeMpM4cvZ/wZL9paWtqGVF5Ja9b13+ASWOtjbUEuyS9AH4CYmMnWPQiuQAvevlMGxxxxxxxxx=

emailing label now...

Thanks!

artbatista

full member

Activity: 158

Merit: 100

Quote from: CanaryInTheMine on December 03, 2013, 03:11:43 PM

Yes, I still have blades. Have received several PMs asking about them.
Thanks!

These are v2 blades?

Art

Topic: [CLOSED] batch #39 0.25 btc per Blade, backplanes .15 - page 3. (Read 18807 times)