Topic: FPGA development board "Lancelot" - accept bitsteam developer's orders. - page 20. (Read 101892 times)

Haha, yes I know they will, but if the 28nms come out before the ASICs they will at least have a chance of entering the market

no, i mean:

130nm ASICs will fuck 28 nm FPGAs to shit. 

So the real contest is time; 28nm vs ASICs.

Probably not the best advertisement for your new product, so I won't quote you

But yes, sadly that is the truth. It's too bad we didn't figure out how to utilize FPGAs earlier.

ASICs will fuck all FGPAs to shit.

Sounds good!

I'm looking forward to seeing how Lancelot will compete with all of the newer FPGAs and possibly ASICs being thrown into the market.

there are some differences between both designs, so at first we will announce a update bitsteam for icarus ,  but will slower than Lancelot. this bitsteam will also used for Lancelot testing.
the reason is Lancelot have some special designs for power and heat dissipation, also some more parts for more functions.

notice that  BitFury Design have a high license fee for their bitsteam, but icarus bitsteam update will be free.

Lancelot will also have free bitsteam update Forever.

 

Elaborate please.

it is written on the first post

wohoo! very exciting.

yeah, some updates.
1:
firmware development is still underway, we hope it will be faster than BitFury Design. but i think everyone know about the difficulty now.

2:
get the PCBs yesterday, will do a trial-production next week (maybe on next Thursday i think, i need to wait for factory scheduling ). after that will do a PCB design revise, then push it to a low-volume production.

3:
pre-orders will be taken after both the firmware and hardware development is over.

 

any updates?

Yes, I am too.

And I am looking forward to Lancelot.
Could you tell us how big the first batch will be?
Or is this still a secret?
Could I get 30 Lancelot boards or how much do you think I could get from the first batch?

Cu,
 Eckmar

 

oh, looks like the mail lost again!

  i pleased about everything goes well.

Hi Ngzhang,

Did you not receive my "thanks" Email to your Gmail address?
It has worked fine a few times, so I assumed that you received it even I did never got a response to my question if I could tell your repair success story here in the forum.
But because you are now writing your question here in the board and not as PM, I am assuming I could tell the public about it.

So here we go:
I really like your attitude and do business with you.
You are a honest and reliable guy and still take care about your products after selling them!
Even with shipments you are flexible and split my shipment bulk order of 30 Icarus boards into two parts, so that the total value of each shipment stayed below 10.000 US$. (Here in Thailand you have to pay some "under the table money to customs" for shipments above 10k US$, so even this was not YOUR problem you had split the shipment to solve MY problem. Thanks again for this!)

After installing the 30 boards, 22 worked fine but 8 failed to work.
So at the beginning I was a bit disappointed about the failure rate of your products.
But you asked me to send the 8 boards back to you and investigate the problem.
After X-Ray you found out that on most boards the UART (USB chip) was damaged and because you test all boards before shipment, I now assume that my Thai stuff did something wrong when installing.
You repaired 7 from 8 boards (on one board the two FPGAs chips were out of order, so no repair make sense) for free and I got back to you saying 1.000 times thank you and asked you about if I can publish this story or not. I wonder why this Email did not pass, because three one did it before.
(In future I will stick to PM over this board.)

Anyway to summaries the hole story:
1.) Flexible and fast shipment to Thailand (no Tax, because of ASIAN!)
2.) Good support after sale (very important for me!)
3.) Good quality of products (assuming now that something went terrible wrong with the installation on our side!)
4.) 29 Icarus boards are running fine and I am happy with them!

So please consider me for the first batch of your new product as a customer again!
I would like to order again 30 boards to take advantage of the 20% discount price, but I am not sure how big your first batch is, so I am willing to take everything you can afford.

A happy and satisfied customer,
 Eckmar

  are the repaired boards working well? 

both answers are YES.

So I assume -20% is at a bulk order of 30?
Could these 30 later on be used on the motherboard which will come in the future?

If both answers are YES, please keep me in mind for your preorder.

Sunny regards from holiday island Koh Samui,
 Eckmar

all my BTC are belong to zhang, i think. (meaning, do want lancelot as my first FPGA.)

pull out today.
looks like we will have a sample in 2-3 weeks...

Hello everybody,

I found the BFL shipping to become more in time lately.

Nontheless I am also courious  for the lancelot plattform.
I guess i will create an alternative water cooling for it like i did for the Bitforce Box and the x6500.


In the meantime you might find this spreadsheet i created usefull for claculating costs and uses:

The Bitcoin mine or invest spreadsheet & mining rig comparison spreadsheet