Topic: Fury/Blizzard tuning and mods - page 4. (Read 115279 times)

good afternoon! puedar someone give me the links where you can download drivers and other software to install The Fury 1.3+ MH / S MINER Scrypt ASIC thanks

I have 3 x Zeus blizzard and 1 x GAWminers Fury on  raspbian with cgminer 4.3.5 the 3 * Zeus units mine ok but the Fury never has any W/U even though it says it's doing 1.4MH/s

Is it possible to flash the Fury to make it into a Zeus blizzard so they are all the same?

I agree it is very exciting.
I cannot wait to try them out.
I have a thunder X6 I reviewed and a Blizzard X6 as well.
So much fun.

Zeusminer upgrades. I think this is pretty cool and saves a ton of money on shipping:

https://zeusminer.com/gen-3/

Unboxing Fury/blizzard
https://www.youtube.com/watch?v=FpgYMdC5t_I

The only sure fire way to set each device is with CGminer, because it bases it on the device's internal ID, rather than the USB slot upon which it's inserted.  You can always shoot a question like this to Luke-JR or NWOOLS right on the BFGMiner thread: https://bitcointalksearch.org/topic/old-bfgminer-4100-gbtstratum-rpc-maclinuxwin64-spondoolies-sp30-626361

 i had one of mine that the light kept going out overnight. i swapped out the usb cable with an extra and now it runs stable 24/7.

BTW, i'm using the cgminer 3.1.1 or whatever from the gaw site, is there any benefit to switching to one of the BFG builds or should i just stick with what i have now? seems to be good, hashrate with 3 furries at 328 is around 3.9mhs total and less than 5% HW's.

@BRADLEYPLOOF
Yes, you are correct, sir.  I do this quiet a bit throughout the day already, adjusting clocks based on HW errors vs Hashrates, etc.  As I mentioned, I use Minera (for now) and if for some reason it auto resets (with the summer heat and all the A/C, just using the microwave will sometimes trip a breaker), then all the adjustments I made are gone.  That is why I am looking for a by ID  base setting, because for example Fury7 will sometimes be ttyUSB2 or maybe it will be ttyUSB6.  I am merely looking to tweak performance to squeeze every MH out of each device that I can.

I still very much appreciate your input.

  regards,
      geno

In regards to the above post about setting separate clock frequencies using BFGminer 4.7, you can hit "M" and use the up and down arrows to switch between devices.  You can then hit "C" and adjust the clock frequencies while running BFGminer, so you don't need to have the startup script set them for you.  Granted, it would be easier to do if you have to restart your rig all the time, but you can still use the "M", "C" options to change individual clocks...

Ok , From your command line, I see you scan all comm ports and add all detected devices; then set all the freqs to 250 (why so low? you should get 325 easily.  just curious)  So have you tried to set individual freqs by ID number?  This is the detail I am trying to sort out before I start modding the serial nums.  I would think it would be something like     --set zus-clk Fury01:335 Fury02:328 Fury03:333   ....etc


I have been using bfgminer 4.7.0  from luke-jr; the version included with Minera (on the Raspberry Pi).  Would you say that DarkWinde's version is more stable or better supports the Fury?


 What is --zeus-cg? I haven't seen this used, or is this specific to DW's version; also, I would have thought that it would be --zus-cg to be in step with the other options.

I really appreciate the info, thanks again.

  regards,
     geno

I used that "CP21xxCustomizationUtility.exe" from this post https://litecointalk.org/index.php?topic=16301.msg183090#msg183090  to set id for for blizzards
I use bfgminer of darkwinde with "   -S zeus:\\.\COMXX  --set zus:chips=6 --set zus:freq=250 --no-submit-stale --zeus-cg " only

multipool has been pretty fast for me since they upgraded the site hardware.

@markBG

Thank you for the feedback. I suppose I should go ahead and give it a try sometime this week,  Do you also initialize those 4 by serial number?  Which software do you use, and what is the --set string, if you don't mind?


 I have been thinking of moving to multipool ( I have been using mupool).  but I hate the website interface - it is slow as hell and times out a lot when I try to check in to verify throughput, etc.  It also logs you off at random intervals it seems, I cannot maintain a constant connection, unlike clevermining.

Anyway, thanks again,

  regards,
    geno

So after all that, here is the question: Has anyone tried changing their Fury/Blizzard serial numbers from the factory 0001 using a utility such as CP21xxCustomizationUtility (which can be found here :  http://www.gmpa.it/it9xxs/?p=1133 ? 
I have 9 fury/blizzard
4 is with changed  serial number like this
other 5 is not
runing with  clq 250 on multipool.us with very good hash

I have 8 Gawminer Furies, all running on one RPi from 3 different 7 port USB hubs (two each have 4 furries and and are plugged into the central one that powers the RPi).  On boot, they are assigned ttyUSB0 through ttyUSB7

Each Fury has its own frequency preference; one can hum all day long at 345 with 2-4% errors and another gives 9% at 328.  I have given up trying to assign individual freqs, because I am certain that every reboot changes the USB number, so problem child ends up spitting 15% because it was set to 345 and golden child is held back at a mere 1.1MH/s.  So that means that after at least 3 to 4 hours, I need to ssh into the RPi and manually adjust the freqs based on individual performance.

So after all that, here is the question: Has anyone tried changing their Fury/Blizzard serial numbers from the factory 0001 using a utility such as CP21xxCustomizationUtility (which can be found here :  http://www.gmpa.it/it9xxs/?p=1133 ? 

If we can do this, Instead of using

and hoping that the correct device gets the right clock setting , for instance.  It should be something like can be used for gridseeds with cgminer (if software supports it):


I am just a little leery trying this until I know it has been done, I would certainly hate to fry one of my little guys.  I have spent quiet some time on google but I have not found anything definitive, such as 'Yes, I have changed my Fury serial number like this'.

Comments?

  regards,
    geno

It usually is something haywire in conf.
The other day my comp decided to assign one of my 4 from port 6 to 7....
Guess what? SGMiner didn't see it....back tracked, reboot and all good.

I solved it. It was the hidden conf files that caused the problems.

So while I am waiting to fix the broken Fury,

I have 3 Furies connected and was running on 2 pools using the following commands:

Started a screen session:

A second screen session:

So it ran fine until today when I have an itchy finger and stopped the mining to do a reboot and was trying out making executables in my RPi.

After not being able to make it run automatically during startup, i just want now to continue mining..

So i just started the screens as per normal, but now, while the ones based on ttyUSB1 and ttyUSB2 ran fine
https://i.imgur.com/PWLFK4r.jpg

the one that runs ttyUSB0 runs and keeps scanning for ttyUSB1, and it will always run with 2 devices USB0 and USB1, no matter if i swap the usb numbers around. I had to disable USB1 in case it interferes with the other instance.
https://i.imgur.com/4VsKPIE.jpg.

This is very weird.

Is there a way to stop cgminer from scanning further after the ttyUSB0 is defined manually?

I'd say that's probably the problem...

And... the micro-usb port is lifting off the pcb. -.-"