Topic: Fusion Silicon (Read 1302 times)
Any firmwares for the X2 miner?
How to disable fan checking?
Problem is solved.
FANs were destroyed by parcel service.
FANs were destroyed by parcel service.
Hello HagssFIN,
thanks for your reply.
Yes, ports are open.
The internet connection seems allright.
At the weekend, I did some changes on the config.
When I deactivate the fans the miner starts up and starts with the mining.
But there are several fan config commands.
I found the command "fan_option":"1".
When I set this to zero it seems the miner deactivate the fans from the software site and doesn't check them.
This config I have run for 30 sec before I have reload the old config, because the temperature of the chips went up really fast to 88°C, without fans.
Normally when the miner gets energy, he starts up very fast and the fans are immediatly on 6000 rpm.
But in the web interface the fans show 0 rpm.
Could it be that the fans are defect or the control borad could not manage them?
It would be very nice, if anybody could post his fusionsilicon X7 miner config, so that I can compre both settings, where is my failure.
I hope not the fans or the control board is damaged.
thanks for your reply.
Yes, ports are open.
The internet connection seems allright.
At the weekend, I did some changes on the config.
When I deactivate the fans the miner starts up and starts with the mining.
But there are several fan config commands.
I found the command "fan_option":"1".
When I set this to zero it seems the miner deactivate the fans from the software site and doesn't check them.
This config I have run for 30 sec before I have reload the old config, because the temperature of the chips went up really fast to 88°C, without fans.
Normally when the miner gets energy, he starts up very fast and the fans are immediatly on 6000 rpm.
But in the web interface the fans show 0 rpm.
Could it be that the fans are defect or the control borad could not manage them?
It would be very nice, if anybody could post his fusionsilicon X7 miner config, so that I can compre both settings, where is my failure.
I hope not the fans or the control board is damaged.
@mpminer86
Your pools use ports 9998 and 3533.
Do you have those ports open ?
Your pools use ports 9998 and 3533.
Do you have those ports open ?
Hello i have a problem with my FusionSilicon X7, too.
At home with DHCP and only behind a DSL-Router he works fine.
The miner starts up fast and begin with the mining.
But in the Datacenter the miner don't begin with the mining prozess.
I hope anyone can help me here with my problem.
And can posts here his X7 cgminer.conf.
So I can check my parameters, to solve the problem.
Thank you.
Needs the miner special ports open?
In the datacenter I can reach the web interface of the miner.
I can see, that he is connecting to the mining pool for a short time and send his user name to the mining pool.
But he don't starts his work, then.
He shows me that the pools are all alive.
But the fan is zero / he shows me 0 rpm.
The Miner goes up and get some work for 2-3 minutes.
Then the intern program cgminer restart new.
I think the cgminer is in a restarting loop.
Over the web interface I can send a ping. Traceroute and DNS works fine, too.
I hope anyone can help me.
Can anyone show / send me his Fusionsilicon X7 Config, so that I get a look what configs maybe are wrong.
It's wondering me because at home the miner has worked fine with the dhcp setting.
In the datacenter he gets not really up and began with the work.
At home with DHCP and only behind a DSL-Router he works fine.
The miner starts up fast and begin with the mining.
But in the Datacenter the miner don't begin with the mining prozess.
I hope anyone can help me here with my problem.
And can posts here his X7 cgminer.conf.
So I can check my parameters, to solve the problem.
Thank you.
Needs the miner special ports open?
In the datacenter I can reach the web interface of the miner.
I can see, that he is connecting to the mining pool for a short time and send his user name to the mining pool.
But he don't starts his work, then.
He shows me that the pools are all alive.
But the fan is zero / he shows me 0 rpm.
The Miner goes up and get some work for 2-3 minutes.
Then the intern program cgminer restart new.
I think the cgminer is in a restarting loop.
Over the web interface I can send a ping. Traceroute and DNS works fine, too.
I hope anyone can help me.
Can anyone show / send me his Fusionsilicon X7 Config, so that I get a look what configs maybe are wrong.
It's wondering me because at home the miner has worked fine with the dhcp setting.
In the datacenter he gets not really up and began with the work.
I did find an off solution..
I disconnected the center board power only keeping the board controller lead connected.
The result is 185GH avg @ 1074watts (cord is no longer too hot to touch)
The red fault light is on (to be expected) and now runs at 68F vs 77F
I have run like this a few days with no issues.
I disconnected the center board power only keeping the board controller lead connected.
The result is 185GH avg @ 1074watts (cord is no longer too hot to touch)
The red fault light is on (to be expected) and now runs at 68F vs 77F
I have run like this a few days with no issues.
I did we chat with support just a bit ago and no real resolution. Pretty much the version i have is best. Mabee the 220v PSU works at 1400watts as they say but 110v (or mine??) is well 1566watts. This was fine for months, but now when my ac kicks on (different breaker) its just enough to trip the breaker the x-7 is on.
If any one has a solution to turn this unit down a bit please let me know!
Otherwise its wait for the strong-U6 to show up in a month or so and leave this one off.
If any one has a solution to turn this unit down a bit please let me know!
Otherwise its wait for the strong-U6 to show up in a month or so and leave this one off.
How can I get a updated firmware from them? I would like to reduce the watts (have to) I have tried unplugging one board, get a start up fail. Need to run this under 1400watts even at a lower hash rate but every menu to possible do so is locked out.
Also as posted earlier altering the config does nothing.
Mine runs 1566watts and makes the cord socket hotter than I want.
Also as posted earlier altering the config does nothing.
Mine runs 1566watts and makes the cord socket hotter than I want.
Chatted with FusionSilicon support for a bit, they said that the new version of firmware is being tested and will be available on their web site soon.
It's important to note that there are at least 2 control boards V3 and V4. Version 4 has SSH locked out "for security reasons" according to support. The latest version is 4.18 for the version 4 control boards and they would not supply me with a file download. You cannot install a version 4 firmware on the version 3 boards and vise versa according to support.
It's important to note that there are at least 2 control boards V3 and V4. Version 4 has SSH locked out "for security reasons" according to support. The latest version is 4.18 for the version 4 control boards and they would not supply me with a file download. You cannot install a version 4 firmware on the version 3 boards and vise versa according to support.
i have a x7 too. and its firmware is 3.11a. i written in wechat with fs. there is no support comma seperated paramaters in password field. they sent to me this firmware, 3.11a. now i learned there is newer version too. i wonder is there xnsub support in v4? i cant add #xnsub at the end of pool url. also i wonder is there any overclock option? and how?
here is my fw: https://ibb.co/j4ZBM0J
here is my fw: https://ibb.co/j4ZBM0J
Hey guys, @astraleureka is going to help extract the image as I'm not sure how to do that correctly. Will post once we get it. Interested to see what else this machine can do.
Thanks for the firmware, I have not installed it yet because the hardware version says 4.0 instead of 3.0. I have 6 X7's and 3 different firmware versions (4 if you count the one you sent me). Not sure how to extract the firmware from the unit but sure would like to know.
Here are my observations:
1) Any firmware after the February release has ssh account locked out and if you upload a settings file (cgminer.conf) from a backup it has no effect on the unit as far as frequency and voltage.
2) There at least 4 different firmware versions out there, maybe more, I've been successful at underclocking and overclocking the February version only
https://systemsguy.com/wp-content/uploads/2019/05/Firmware3.11-1024x692.png
https://systemsguy.com/wp-content/uploads/2019/05/Firmware4.15-800x666.png
https://systemsguy.com/wp-content/uploads/2019/05/Firmware4.18-1024x866.png
can im run the miner without a pc onyl with ehternett connektion?
Hello. The hash rate is constantly falling for me, 1 card does not work at all on one ASIC. What to do, tell me? Have a firmware?
I had the same bad luck with my X7. I ended up sending it back for warranty fix, even though it was supposed to be new. Hoping it gets there.
Hello. The hash rate is constantly falling for me, 1 card does not work at all on one ASIC. What to do, tell me? Have a firmware?
Hi! Yes I do. Send me a message on telegram or discord:
discord: cryptostevo#6966
telegram: @cryptostevo
Also, these guys are releasing the x7+ maybe end of the month, and the X2 soon (which mines 3 algos including Groestl). Seems to all be in small batches of 200-300 units each.
discord: cryptostevo#6966
telegram: @cryptostevo
Also, these guys are releasing the x7+ maybe end of the month, and the X2 soon (which mines 3 algos including Groestl). Seems to all be in small batches of 200-300 units each.
Hello
X7+ will be postponed till July/August and X2 is now available for only 80 units.
send me an email if you want.
[email protected]
fusionsilicon doesn't even have X2 for sale. Where are people getting these?
Hi guys,
Only 80 units X2 are available now. Let me know when you are interested.
The best price for it.
[email protected]
Only 80 units X2 are available now. Let me know when you are interested.
The best price for it.
[email protected]
https://bitcointalk.org/index.php?topic=5121740.new#new
Group buy for X2 at 3600usd inc psu and shipping
Group buy for X2 at 3600usd inc psu and shipping
Joyson send us email periodically as well. Seem nice enough but unless a reseller is willing to give us net30 we'll look to source from manufactures directly, plus buying inventory isn't something we typically do given how lean we operate.
Also, I'm skeptical to buy something from a fusion right now as their own website has been down for about 24hrs.
Also, I'm skeptical to buy something from a fusion right now as their own website has been down for about 24hrs.
Jump to: