Topic: [GROUP BUY WORLDWIDE]BTMine v1 Miner 200GH/s BTC 2.4 - page 11. (Read 97268 times)
Theres should be two temp readings, Temp1 in intake air temp Temp2 is output air temp. One of my units was missing the Temp2 sensory and only shows the intake air temperature. I monitor this unit very closely and it seems to be doing fine with an upgraded power supplies and running at 1500 mhz.
If I tried to hold my finger on any of the exhaust grills it would be very uncomfortable, these units blow out a lot of hot air!!!
Mtnminer
If I tried to hold my finger on any of the exhaust grills it would be very uncomfortable, these units blow out a lot of hot air!!!
Mtnminer
I think that I have problem with measure temp, my fan's have 900-1200 RMPS, and in the www temp show me 36 degree, but when I touch cooler my finger brew, so how may I check the temperature sensor ? where he is located ? I saw that the one grey thin cable is inside.
thanks for advice
thanks for advice
I have in Api Log:
[STATS] => 0
[ID] => AVA0
[Elapsed] => 240
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 480
[fan3] => 480
[temp1] => 33
[temp2] => -1
[temp3] => -1
[temp_max] => 33
[Device Hardware%] => 6.2112
[no_matching_work] => 170
[match_work_count1] => 1
[match_work_count2] => 0
[match_work_count3] => 734
[match_work_count4] => 750
[match_work_count5] => 408
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 746
[match_work_count9] => 0
[match_work_count10] => 678
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 696
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 13141 0
I think it isn't good ?;/
[STATS] => 0
[ID] => AVA0
[Elapsed] => 240
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 480
[fan3] => 480
[temp1] => 33
[temp2] => -1
[temp3] => -1
[temp_max] => 33
[Device Hardware%] => 6.2112
[no_matching_work] => 170
[match_work_count1] => 1
[match_work_count2] => 0
[match_work_count3] => 734
[match_work_count4] => 750
[match_work_count5] => 408
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 746
[match_work_count9] => 0
[match_work_count10] => 678
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 696
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 13141 0
I think it isn't good ?;/
To change your fan speeds to slower speed use one these settings in the configurations, more options. depending on how yours is wired, one will give you fastest fan speed and the other the slowest fan speed.
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
Hi,
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I asked to declare 60 usd, their declared 150 usd , amateurs..
, amateurs..
hi everyone,
i have a problem.
i have got mine avalon in country. and now besides paying customs/taxes fees, DHL is saying that I need to pay extra 600euros for shipping!!!
anyone got that problem?
i have a problem.
i have got mine avalon in country. and now besides paying customs/taxes fees, DHL is saying that I need to pay extra 600euros for shipping!!!
anyone got that problem?
I think that I have problem with measure temp, my fan's have 900-1200 RMPS, and in the www temp show me 36 degree, but when I touch cooler my finger brew, so how may I check the temperature sensor ? where he is located ? I saw that the one grey thin cable is inside.
thanks for advice
thanks for advice
Great news, congratulations. I am now upto 900-920 gh/s waiting for more power supplies to arrive. I have one more to get online and three more that need the power supplies upgraded from the factory one.
I am overclocking the one with the new upgraded power supply to 1500 mhz, I tried 1600 mhz but the hashing speed became very unstable. Is anyone running faster than 1500 mhz, I want to squeeze all I can out of these machines!
Mtnminer
Hey dudes
Many tks for the update file, now my miner is running much better
This forum rocks
Also the fans are a lot more stable
Props to all, hope u guys solve all your problems my miner is running 210Gh super stable, along with my 8 hexa2 miners i get almost 400Gh
Price is dropping for this miners also when the chinese guys return maybe its too late for them new generation is coming and difficulty is going high
Anyway this baby scream´s like hell but i think its going to pay off
I am overclocking the one with the new upgraded power supply to 1500 mhz, I tried 1600 mhz but the hashing speed became very unstable. Is anyone running faster than 1500 mhz, I want to squeeze all I can out of these machines!
Mtnminer
Hey dudes
Many tks for the update file, now my miner is running much better
This forum rocks Also the fans are a lot more stable
Props to all, hope u guys solve all your problems my miner is running 210Gh super stable, along with my 8 hexa2 miners i get almost 400Gh
Price is dropping for this miners also when the chinese guys return maybe its too late for them new generation is coming and difficulty is going high
Anyway this baby scream´s like hell but i think its going to pay off
I´m using the PSU that came with the miner, no problem so far but i won´t overclock it, it´s running stable in 1400 that´s good for me
Instead of new PSU i could get one watercooling kit, but anyway this baby as 1 month to rock then its time to go so i will not even buy that
Great news, congratulations. I am now upto 900-920 gh/s waiting for more power supplies to arrive. I have one more to get online and three more that need the power supplies upgraded from the factory one.
I am overclocking the one with the new upgraded power supply to 1500 mhz, I tried 1600 mhz but the hashing speed became very unstable. Is anyone running faster than 1500 mhz, I want to squeeze all I can out of these machines!
Mtnminer
Hey dudes
Many tks for the update file, now my miner is running much better This forum rocks
Also the fans are a lot more stable
Props to all, hope u guys solve all your problems my miner is running 210Gh super stable, along with my 8 hexa2 miners i get almost 400Gh
Price is dropping for this miners also when the chinese guys return maybe its too late for them new generation is coming and difficulty is going high
Anyway this baby scream´s like hell but i think its going to pay off
I am overclocking the one with the new upgraded power supply to 1500 mhz, I tried 1600 mhz but the hashing speed became very unstable. Is anyone running faster than 1500 mhz, I want to squeeze all I can out of these machines!
Mtnminer
Hey dudes
Many tks for the update file, now my miner is running much better
This forum rocks Also the fans are a lot more stable
Props to all, hope u guys solve all your problems my miner is running 210Gh super stable, along with my 8 hexa2 miners i get almost 400Gh
Price is dropping for this miners also when the chinese guys return maybe its too late for them new generation is coming and difficulty is going high
Anyway this baby scream´s like hell but i think its going to pay off
Hey dudes
Many tks for the update file, now my miner is running much better
This forum rocks Also the fans are a lot more stable
Props to all, hope u guys solve all your problems my miner is running 210Gh super stable, along with my 8 hexa2 miners i get almost 400Gh
Price is dropping for this miners also when the chinese guys return maybe its too late for them new generation is coming and difficulty is going high
Anyway this baby scream´s like hell but i think its going to pay off
Anyone swap out the fans yet? Can we just use standard 120mm ones?
These fans move 200+ cfm. Most regular 120mm are under 100. Be careful using new fans.
Also can someone post their cgminer API log? Mtnminer?
Listen the man! Froget buying some computer fans that run 800rpm, your miner wont stay up 120seconds with them.
These units pull 1000w so they are effectively 1kw heaters you cannot cool them with just 2 regular computer fans. Least not in inhouse room temperature of 23-26. I run my miners in warehouse with temp below of 20c and now testing stock psu and it seems to hold the 1500 OC but it gets enough cooling. Also psu works better if not overheating...
*no ATX psu is ment to be treated 100% load stress 24/7 expect them to blow up*
For silent treatment you need the watercooling kit from Aliexpress
2 sample API logs with 1500 Overclock. New firmware 20131229
I get 3.7 and 3.7 HW errors with 1500 OC
Both of these miners have 5 dead chips.
Code:
[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: 54d7569
luci: 346e3e7
Reply was 'STATUS=S,When=1391125525,Code=70,Msg=CGMiner stats,Description=cgminer 3.9.0|STATS=0,ID=AVA0,Elapsed=7634,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,baud=115200,miner_count=16,asic_count=10,timeout=8,frequency=1500,fan1=0,fan2=2760,fan3=2760,temp1=28,temp2=32,temp3=-1,temp_max=32,Device Hardware%=3.7541,no_matching_work=5051,match_work_count1=13152,match_work_count2=26389,match_work_count3=26169,match_work_count4=26283,match_work_count5=25960,match_work_count6=26123,match_work_count7=26117,match_work_count8=26104,match_work_count9=25957,match_work_count10=26215,match_work_count11=26272,match_work_count12=26202,match_work_count13=26346,match_work_count14=26506,match_work_count15=26212,match_work_count16=26257,Controller Version=0,Avalon Chip=55,USB Pipe=0,USB Delay=r0 0.000000 w0 0.000000,USB tmo=450032 0|STATS=1,ID=POOL0,Elapsed=7634,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=127.99804688,Min Diff=3.99993896,Max Diff=255.99609375,Min Diff Count=514,Max Diff Count=190806,Times Sent=2469,Bytes Sent=359156,Times Recv=2797,Bytes Recv=3033565,Net Bytes Sent=359156,Net Bytes Recv=3033565|STATS=2,ID=POOL1,Elapsed=7634,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=0.00000000,Min Diff=0.00000000,Max Diff=0.00000000,Min Diff Count=0,Max Diff Count=0,Times Sent=2,Bytes Sent=141,Times Recv=5,Bytes Recv=2524,Net Bytes Sent=141,Net Bytes Recv=2524|'
[STATUS] =>
(
[STATUS] => S
[When] => 1391125525
[Code] => 70
[Msg] => CGMiner stats
[Description] => cgminer 3.9.0
)
[STATS0] =>
(
[STATS] => 0
[ID] => AVA0
[Elapsed] => 7634
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 8
[frequency] => 1500
[fan1] => 0
[fan2] => 2760
[fan3] => 2760
[temp1] => 28
[temp2] => 32
[temp3] => -1
[temp_max] => 32
[Device Hardware%] => 3.7541
[no_matching_work] => 5051
[match_work_count1] => 13152
[match_work_count2] => 26389
[match_work_count3] => 26169
[match_work_count4] => 26283
[match_work_count5] => 25960
[match_work_count6] => 26123
[match_work_count7] => 26117
[match_work_count8] => 26104
[match_work_count9] => 25957
[match_work_count10] => 26215
[match_work_count11] => 26272
[match_work_count12] => 26202
[match_work_count13] => 26346
[match_work_count14] => 26506
[match_work_count15] => 26212
[match_work_count16] => 26257
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 450032 0
)
[STATS1] =>
(
[STATS] => 1
[ID] => POOL0
[Elapsed] => 7634
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 127.99804688
[Min Diff] => 3.99993896
[Max Diff] => 255.99609375
[Min Diff Count] => 514
[Max Diff Count] => 190806
[Times Sent] => 2469
[Bytes Sent] => 359156
[Times Recv] => 2797
[Bytes Recv] => 3033565
[Net Bytes Sent] => 359156
[Net Bytes Recv] => 3033565
)
[STATS2] =>
(
[STATS] => 2
[ID] => POOL1
[Elapsed] => 7634
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 0.00000000
[Min Diff] => 0.00000000
[Max Diff] => 0.00000000
[Min Diff Count] => 0
[Max Diff Count] => 0
[Times Sent] => 2
[Bytes Sent] => 141
[Times Recv] => 5
[Bytes Recv] => 2524
[Net Bytes Sent] => 141
[Net Bytes Recv] => 2524
)
Code:
[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: 54d7569
luci: 346e3e7
Reply was 'STATUS=S,When=1391125532,Code=70,Msg=CGMiner stats,Description=cgminer 3.9.0|STATS=0,ID=AVA0,Elapsed=31094,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,baud=115200,miner_count=16,asic_count=10,timeout=8,frequency=1500,fan1=0,fan2=2160,fan3=2280,temp1=27,temp2=45,temp3=-1,temp_max=45,Device Hardware%=3.8715,no_matching_work=20635,match_work_count1=106272,match_work_count2=106448,match_work_count3=106170,match_work_count4=106613,match_work_count5=106596,match_work_count6=106568,match_work_count7=106514,match_work_count8=106321,match_work_count9=106854,match_work_count10=106719,match_work_count11=106557,match_work_count12=53728,match_work_count13=106603,match_work_count14=107317,match_work_count15=106613,match_work_count16=106607,Controller Version=0,Avalon Chip=55,USB Pipe=0,USB Delay=r0 0.000000 w0 0.000000,USB tmo=1832423 0|STATS=1,ID=POOL0,Elapsed=31094,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=127.99804688,Min Diff=3.99993896,Max Diff=255.99609375,Min Diff Count=3412,Max Diff Count=53023,Times Sent=13252,Bytes Sent=1936727,Times Recv=14062,Bytes Recv=7962179,Net Bytes Sent=1936727,Net Bytes Recv=7962179|STATS=2,ID=POOL1,Elapsed=31094,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=0.00000000,Min Diff=0.00000000,Max Diff=0.00000000,Min Diff Count=0,Max Diff Count=0,Times Sent=2,Bytes Sent=141,Times Recv=5,Bytes Recv=2256,Net Bytes Sent=141,Net Bytes Recv=2256|'
[STATUS] =>
(
[STATUS] => S
[When] => 1391125532
[Code] => 70
[Msg] => CGMiner stats
[Description] => cgminer 3.9.0
)
[STATS0] =>
(
[STATS] => 0
[ID] => AVA0
[Elapsed] => 31094
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 8
[frequency] => 1500
[fan1] => 0
[fan2] => 2160
[fan3] => 2280
[temp1] => 27
[temp2] => 45
[temp3] => -1
[temp_max] => 45
[Device Hardware%] => 3.8715
[no_matching_work] => 20635
[match_work_count1] => 106272
[match_work_count2] => 106448
[match_work_count3] => 106170
[match_work_count4] => 106613
[match_work_count5] => 106596
[match_work_count6] => 106568
[match_work_count7] => 106514
[match_work_count8] => 106321
[match_work_count9] => 106854
[match_work_count10] => 106719
[match_work_count11] => 106557
[match_work_count12] => 53728
[match_work_count13] => 106603
[match_work_count14] => 107317
[match_work_count15] => 106613
[match_work_count16] => 106607
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 1832423 0
)
[STATS1] =>
(
[STATS] => 1
[ID] => POOL0
[Elapsed] => 31094
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 127.99804688
[Min Diff] => 3.99993896
[Max Diff] => 255.99609375
[Min Diff Count] => 3412
[Max Diff Count] => 53023
[Times Sent] => 13252
[Bytes Sent] => 1936727
[Times Recv] => 14062
[Bytes Recv] => 7962179
[Net Bytes Sent] => 1936727
[Net Bytes Recv] => 7962179
)
[STATS2] =>
(
[STATS] => 2
[ID] => POOL1
[Elapsed] => 31094
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 0.00000000
[Min Diff] => 0.00000000
[Max Diff] => 0.00000000
[Min Diff Count] => 0
[Max Diff Count] => 0
[Times Sent] => 2
[Bytes Sent] => 141
[Times Recv] => 5
[Bytes Recv] => 2256
[Net Bytes Sent] => 141
[Net Bytes Recv] => 2256
)
Anyone swap out the fans yet? Can we just use standard 120mm ones?
These fans move 200+ cfm. Most regular 120mm are under 100. Be careful using new fans.
Also can someone post their cgminer API log? Mtnminer?
On one of the damaged miners, without power supplies I was working today was a nightmare. I removed the blades reinstalled three capacitors. Installed two Corsair CX750 power supplies, while reinstalling the blades knocked off two of the three capacitors I replaced!!!! I said just forget it and finished the installation.
http://www.tigerdirect.com/applications/searchtools/item-details.asp?EdpNo=3844176&tab=7&SRCCODE=WEBLET03SHIP&cm_mmc=Email-_-WebletMain-_-WEBLET03SHIP-_-03ship&utm_source=EML&utm_medium=main&utm_campaign=WEBLET03SHIP&cm_lm=dennis@hydencafe.com
It is now up and running, hashing at 223 gh/s at 1400 mhz. I am happy, after it settles I will try increasing the frequency with these power supplies and see how it goes? I did discover another problem with this unit, it is missing thermocoupler for temp2, I will have to keep an eye on this!
I will update more later.
Mtnminer
http://www.tigerdirect.com/applications/searchtools/item-details.asp?EdpNo=3844176&tab=7&SRCCODE=WEBLET03SHIP&cm_mmc=Email-_-WebletMain-_-WEBLET03SHIP-_-03ship&utm_source=EML&utm_medium=main&utm_campaign=WEBLET03SHIP&cm_lm=dennis@hydencafe.com
It is now up and running, hashing at 223 gh/s at 1400 mhz. I am happy, after it settles I will try increasing the frequency with these power supplies and see how it goes? I did discover another problem with this unit, it is missing thermocoupler for temp2, I will have to keep an eye on this!
I will update more later.
Mtnminer
Anyone swap out the fans yet? Can we just use standard 120mm ones?
Hi I have maybe stupid noob question but how did you know that you have 5 cold chips ? it is some way to check to boards ?
After the night in the statistics in my mine I have measures form 230GH/s to 140 GH/s, I have to Antminer and there are stable it maybe 2-3% differential.
tnx for advice
but how did you know that you have 5 cold chips ? it is some way to check to boards ?After the night in the statistics in my mine I have measures form 230GH/s to 140 GH/s, I have to Antminer and there are stable it maybe 2-3% differential.
tnx for advice
If you go to the API Log, you can see how each of the individual miners (groups of chips) are doing.
As for you widely varying hashrate, again, look at your API Log and you'll be able to see what's going on. If some are hashing at half-rate, then that's the info that 5 chips are cold.
My miners three miners with the upgraded were running great after the flash. This made a big difference with fans speed stability on the factory power supplies. So I decided to get brave and push them up from 1400 mhz to 1500 mhz. As Btmine said so not overclock with the factory power supplies, they were honest. 1500 mhz isn't overclocking per the Avalon chip design, but for these factory power supplies it is too much!
They all shut down withing 3 minutes of increasing the frequency. The factory power supplies are at their max capacity at 1400 mhz. Btmine knew this and that is the reason for the overclock warning. There was no permanent damage, I had to give the power supplies about five minutes to cool, reboot and set the configs back to 1400 mhz. Now all is back to normal had hashing happily again!
When I get my power supplies delivered and installed in the two damaged units I am repairing that came with power supplies, I will post the results on these and what power I can squeeze out of them. The power supplies I have coming for these are 2 750 watt units and 4 900 watt units. These are matched pairs of two different brands. I will post those details with the update too.
Mtnminer
They all shut down withing 3 minutes of increasing the frequency. The factory power supplies are at their max capacity at 1400 mhz. Btmine knew this and that is the reason for the overclock warning. There was no permanent damage, I had to give the power supplies about five minutes to cool, reboot and set the configs back to 1400 mhz. Now all is back to normal had hashing happily again!
When I get my power supplies delivered and installed in the two damaged units I am repairing that came with power supplies, I will post the results on these and what power I can squeeze out of them. The power supplies I have coming for these are 2 750 watt units and 4 900 watt units. These are matched pairs of two different brands. I will post those details with the update too.
Mtnminer
can someone post their cgminer API log? i want to be sure im running correct settings.
I updated my firmware and now they are running much more stable. My errors have never been very high but lots of fan control issues. Perhaps flashing and updating your firmware will help you too?
Here is the upgrade firmware link
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin
Mtnminer
Here is the upgrade firmware link
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin
Mtnminer
Anyone having to reboot their machine daily because of errors?
Also how can I access this remotely
Also how can I access this remotely
I will try to do this today, I will have two of my damaged one apart replacing capacitors. I think i can get a good shot of one on these units.
Mtnminer
Mtnminer
Hi,
pls, can you somebody take a photo of pdu board from this unit? I need v1.8. I think that in my board is missing some caps and two are bad.
Anyway, order from 1/8/2014 delivered yesterday - 1/29/2014.
pls, can you somebody take a photo of pdu board from this unit? I need v1.8. I think that in my board is missing some caps and two are bad.
Anyway, order from 1/8/2014 delivered yesterday - 1/29/2014.
I sold my Avalon and did a Reset-to-Defaults
Now they buyer says its hashing only 60GH
Could someone please upload me their configuration.tar.gz from the Backup Tab?
Now they buyer says its hashing only 60GH
Could someone please upload me their configuration.tar.gz from the Backup Tab?
Here u go: https://www.dropbox.com/s/0dndepnlcneyodu/backup-OpenWrt-2014-01-30.tar.gz
Ip is 192.168.0.4 ..
OpenWrt version is 20131229 ..
Jump to: