You misunderstand each other.
Give us TW access and I'll try to fix it for you
Topic: [Guide] Dogie's Comprehensive Technobit HEX4M [HD] (Read 9771 times)
Interestingly it is not an option to disable.
Disable HEXM reset code (cgminer seting) via web and try again
Disable HEXM reset code (cgminer seting) via web and try again
Loshia and Martin have both offered to TW in and check it out as well. I will try that next and see how far we get.
Thank you for the help.
Thank you for the help.
If all of them is checked, then last resort is RMA 
If all of them is checked, then last resort is RMA
Now it sort of starts and then disables the miner.
With the Hex is was working fine I did nothing to it and it stopped.
I have hooked it up to a windows system it sees the miner. I just dont want to set it up on that one as it runs an array of Scrypt miners.
Here is what I get on the TP-Link again.
I have hooked it up to a windows system it sees the miner. I just dont want to set it up on that one as it runs an array of Scrypt miners.
Here is what I get on the TP-Link again.
Of course you can always switch back to previous version of TPLINK firmware that work before
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
Of course you can always switch back to previous version of TPLINK firmware that work before
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
So close. Now I have a Zombie. LOL
Hex4m is set for the handle USB error.
Remove the USB HUB Hex4m is set for the handle USB error.
Check again your cgminer configuration page.
Handle usb detect error as : set to hex4m
Handle usb detect error as : set to hex4m
Power off 12V of HEXM
Remove USB HEXM cable
Power on 12V of hexM
PLUG USB cable of HEXM into tplink without hub directly
and make sure your USB cable is OK
So close. Now I have a Zombie. LOL
Hex4m is set for the handle USB error.
Hex4m is set for the handle USB error.
Check again your cgminer configuration page.
Handle usb detect error as : set to hex4m
Handle usb detect error as : set to hex4m
Check again your cgminer configuration page.
Handle usb detect error as : set to hex4m
Handle usb detect error as : set to hex4m
Just power off HEXM board - unplug USB + 12V
Reboot tplink
power on 12V of HM board and finally plug USB cable
And you can remove hub also just plug board directly and make sure lsusb shows it
Reboot tplink
power on 12V of HM board and finally plug USB cable
And you can remove hub also just plug board directly and make sure lsusb shows it
Closer but not quite.
Rebooting the TP-Link and also SSH in and tried it manually.
Otherwise you need to restart cgminer
Or better just execute /usr/bin/fix_rc it will enable udevd and reboot tplink the all will be good
Rebooting the TP-Link and also SSH in and tried it manually.
It's a bit different this time. I changed the cable and the hub again.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
So it shall be mining if your udevd is started. I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
Otherwise you need to restart cgminerOr better just execute /usr/bin/fix_rc it will enable udevd and reboot tplink the all will be good
It's a bit different this time. I changed the cable and the hub again.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
So it shall be mining if your udevd is started. I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
Otherwise you need to restart cgminerOr better just execute /usr/bin/fix_rc it will enable udevd and reboot tplink the all will be good
It's a bit different this time. I changed the cable and the hub again.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I wish there was a RPi image for it. I have a ton of them. I will test it on a windows system.
Thank you for your help I do appreciate it.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
Thank you for your help I do appreciate it.
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Sorry it's 4:30am here I am a bit slow.
dude in shell please type lsusb and post output can you?
Jump to: