I have 4 S2's that arrived yesterday. 1 looked like it was thrown down 20 flights of stairs (backplane bent to hell) and non-functional. So as mentioned above, you need to undo the ~15 screws and look inside. The box mentioned above had both the ribbon cable to the controller and the network cable undone internally as so many cards were dislodged in shipment.
I did have 2 units arrive in good condition but sadly only one of the four is operating to spec (~ 1Th/s). Hoping to get this sorted in the coming days...
Topic: Help New AntMiner S2 Lcd not working and cant connect. (Read 818 times)
Hello.
My problem is that when im turning on my AntMiner S2 its making lots of noice like its working all properly but my Lcs is not working at all. Its like just not working , no leds working no beeping and not even lightening , and of courst showing nothink on it. I hoped its not that bad , that maybe i can just configure it without that lcd working. I followed to steps from other topic : https://bitcointalksearch.org/topic/guide-dogies-comprehensive-bitmain-antminer-s2-setup-hd-518205
"Configuration is straight forward as Antminer S2s are standalone.
Power on as above.
Plug in a network cable from the S2 to your router.
Change your router's subnet to 1, ie 192.168.1.x. This is just temporary. If this is not possible, see below indented steps.
Unplug your computer from all internet sources.
Plug in a network cable from the S2 to your computer.
Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings
Right click on your ethernet adapter -> Properties
Click on "Internet Protocol Version 4" and click properties
Select "Use the following IP address" and enter the following:
IP Address: 192.168.1.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.1.99
Resume normal steps.
Using a browser, navigate to 192.168.1.99 - this goes to the S2's configuration page."
I done all that and still not connection into this configuration page , its not finding anythink.
Do You know what's seams to be a problem?
My problem is that when im turning on my AntMiner S2 its making lots of noice like its working all properly but my Lcs is not working at all. Its like just not working , no leds working no beeping and not even lightening , and of courst showing nothink on it. I hoped its not that bad , that maybe i can just configure it without that lcd working. I followed to steps from other topic : https://bitcointalksearch.org/topic/guide-dogies-comprehensive-bitmain-antminer-s2-setup-hd-518205
"Configuration is straight forward as Antminer S2s are standalone.
Power on as above.
Plug in a network cable from the S2 to your router.
Change your router's subnet to 1, ie 192.168.1.x. This is just temporary. If this is not possible, see below indented steps.
Unplug your computer from all internet sources.
Plug in a network cable from the S2 to your computer.
Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings
Right click on your ethernet adapter -> Properties
Click on "Internet Protocol Version 4" and click properties
Select "Use the following IP address" and enter the following:
IP Address: 192.168.1.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.1.99
Resume normal steps.
Using a browser, navigate to 192.168.1.99 - this goes to the S2's configuration page."
I done all that and still not connection into this configuration page , its not finding anythink.
Do You know what's seams to be a problem?
You should have opened it up and made sure everything was connected and seated correctly before turning it on.
Hello.
My problem is that when im turning on my AntMiner S2 its making lots of noice like its working all properly but my Lcs is not working at all. Its like just not working , no leds working no beeping and not even lightening , and of courst showing nothink on it. I hoped its not that bad , that maybe i can just configure it without that lcd working. I followed to steps from other topic : https://bitcointalksearch.org/topic/guide-dogies-comprehensive-bitmain-antminer-s2-setup-hd-518205
"Configuration is straight forward as Antminer S2s are standalone.
Power on as above.
Plug in a network cable from the S2 to your router.
Change your router's subnet to 1, ie 192.168.1.x. This is just temporary. If this is not possible, see below indented steps.
Unplug your computer from all internet sources.
Plug in a network cable from the S2 to your computer.
Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings
Right click on your ethernet adapter -> Properties
Click on "Internet Protocol Version 4" and click properties
Select "Use the following IP address" and enter the following:
IP Address: 192.168.1.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.1.99
Resume normal steps.
Using a browser, navigate to 192.168.1.99 - this goes to the S2's configuration page."
I done all that and still not connection into this configuration page , its not finding anythink.
Do You know what's seams to be a problem?
My problem is that when im turning on my AntMiner S2 its making lots of noice like its working all properly but my Lcs is not working at all. Its like just not working , no leds working no beeping and not even lightening , and of courst showing nothink on it. I hoped its not that bad , that maybe i can just configure it without that lcd working. I followed to steps from other topic : https://bitcointalksearch.org/topic/guide-dogies-comprehensive-bitmain-antminer-s2-setup-hd-518205
"Configuration is straight forward as Antminer S2s are standalone.
Power on as above.
Plug in a network cable from the S2 to your router.
Change your router's subnet to 1, ie 192.168.1.x. This is just temporary. If this is not possible, see below indented steps.
Unplug your computer from all internet sources.
Plug in a network cable from the S2 to your computer.
Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings
Right click on your ethernet adapter -> Properties
Click on "Internet Protocol Version 4" and click properties
Select "Use the following IP address" and enter the following:
IP Address: 192.168.1.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.1.99
Resume normal steps.
Using a browser, navigate to 192.168.1.99 - this goes to the S2's configuration page."
I done all that and still not connection into this configuration page , its not finding anythink.
Do You know what's seams to be a problem?
Jump to: