Pages:
Author

Topic: INNOSILICON A4 DOMINATOR SETUP GUIDE ---REVAMPED (Read 10860 times)

member
Activity: 97
Merit: 10
Does anybody have new firmware for dominators ?
or some setting to save electricity ?

ThX


Just drop your voltages until they stop working for each speed.
I run 3 units connected to a single controller at 900Mhz/730Mv and get 310Mh/s at 920 Watts.
newbie
Activity: 7
Merit: 0
Does anybody have new firmware for dominators ?
or some setting to save electricity ?

ThX
newbie
Activity: 15
Merit: 0

Does someone know how to use the --CS switch of cgminer ?!

i can only use --CS 8 (for all blades) or only 1 blade (--CS 1, or --CS 2, ect ect)

i'de like to use 2 blade, and the other 2 blades on a different cgminer instance.
so u think --CS 1,2 would work... but i doesn't.

any help appreciated !
newbie
Activity: 15
Merit: 0
Dose anyone know how to enable API access?

You mean the API of cgminer ?!
try cgminer /? 

if i'm correct: --api-listen --api-network
newbie
Activity: 15
Merit: 0
Did anyone tinker with the settings yet ?!

I'm looking for a way to under/over clock these A4's (280mh version) to get a better w/mh
at the moment i'm stuck at 3,2 w/mh at the lowest..  (700v - 800mhz)

also, innosilicon used a custom cgminer version for there dominators but did not released the sourcecode.
(But hey, cgminer is released under gpl-v3 !!, gimme the source!)

what i'm looking for are the most optimal settings (A1pll and A1vol)

Cheers.
member
Activity: 154
Merit: 10
Hi everyone,

My A4 meet this issues 1 ASC is not working, detail in picture:
https://ibb.co/cNLKT6

How can i fix it?
Thanks you
newbie
Activity: 75
Merit: 0
Guys, help me to flash my A4.
The problem is that I download firmware, any version, using the program Win32DiskImager to create the image on the SD card. Get a control Board, and the miner does not load the system.
what file system must be created on the SD card? NTFS FAT32 exFAT?
Does it matter?
Even after I write the image to the card, when trying to load a map I find that the map is empty and no files.
Please tell me how to understand what's going on?
Now on my miner address 192.168.1.150
after flashing to change this address??
newbie
Activity: 3
Merit: 0
newbie
Activity: 7
Merit: 0
can somebody help me !
I tried to cchanged IP adress but no luck.

I tried to delete old one and press setup, but it never conects again.
I also tried to write new one and press setup but it never conects again.

Somebody !

Please..
newbie
Activity: 4
Merit: 0
I have 2 kind of controller for A4
1. Use SD card
-> i find that the ​software: https://www.dropbox.com/s/sis8eoeo6wxoqdv/G5-20-V2.0.3.zip?dl=0
2. Use micro sd card
I cannot find its software. Please help me
newbie
Activity: 7
Merit: 0
Hello, any help appreciated.
I am trying to set up a pair of a4s. Everything is hooked up. I changed the ip on my laptop, but when I go to the default miner ip, it times out and cant find the setup page..I did see a flash of it before changing my pc ip, but it went away before I could even click English...now nothing..
legendary
Activity: 1274
Merit: 1000
if it's not the image send them a email here

[email protected]


they will get back with you in about day or have with me so far i was like wow when they did ...
hero member
Activity: 952
Merit: 508
Can anyone possibly assist me.. i have an a4 dominator that suddenly 3 cards stopped hashing. If i connect the one card by itself it stays on operating status running and starts to hash. If i connect any or all of the other 3 it goes from operating status running to stop before it starts hashing

Sounds like one or more boards is bad.

If you test one board at a time, do the work individually?

If yes, you may have something wrong with your Pi

I see posts in your history that indicate you have more than one of these, have you tried swapping the controllers? different SD card with fresh image?
newbie
Activity: 12
Merit: 0
Can anyone possibly assist me.. i have an a4 dominator that suddenly 3 cards stopped hashing. If i connect the one card by itself it stays on operating status running and starts to hash. If i connect any or all of the other 3 it goes from operating status running to stop before it starts hashing
newbie
Activity: 5
Merit: 0
Hey guys. I'm having trouble connecting to my a4. I log into my modem and it does not show the miner on the device table. I try to log into the default ip of the dominator but I get the time expired error.

I checked out a couple setup guides that mentioned the modem should have the ip of 192.168.1.1 (mine is 192.168.0.1) but I'm not able to change mine. I was wondering if anyone else has either had the same problem or was able to get around this.

Please help!!!
newbie
Activity: 39
Merit: 0
Thanx for guide, really helpful.
newbie
Activity: 3
Merit: 0
Hi Guys!

Who are measure A4 noise level?
How many DB the one unit + PSU provide?

Thanks
newbie
Activity: 13
Merit: 0
How about the links to Dominator's firmware?

This is the link they sent me to be able to download the .iso file. They suggested using Win32 Disk Imager to reflash the SD card, it does split it up into 3 partitions. As far I can tell, a boot partition in Fat32, an EXT4 for main filesystem, and then a swap partition.

https://www.dropbox.com/s/lhl4tx1sqi3xw4u/G5-1102.rar?dl=0
What this version?
0.0.3
1.0.3
or  2.0.2
i need 0.0.3  and 2.0.2
Have 2 different miners need this.
Can say plz when i can get this?
newbie
Activity: 9
Merit: 0
Update, got miner back online. v2.0.2beta. But not happy yet. need to have either on balance by quota or autos witch every hours...



Do you have a link to the beta firmware?  I'm having a similar issue.  My miner appears to be hashing but still reports 0 accepted shares.  Running V2.0.1 FW right now.
sr. member
Activity: 503
Merit: 250
Update, got miner back online. v2.0.2beta. But not happy yet. need to have either on balance by quota or autos witch every hours...

Pages:
Jump to: