Topic: Just purchased an S9 Miner off Ebay and it has one heatsink missing? Still Mines (Read 287 times)

 
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203704K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25672K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12632K (cceab000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  ? 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Broadcom BCM5241 e000b000.etherne:00: attached PHY driver [Broadcom BCM5241] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 26/13, WL threshold: 4096, image sequence number: 1096145258
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 7893A978-0C61-4250-9E4B-39014213963B, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 3772/565, WL threshold: 4096, image sequence number: 2121478933
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID D1567B42-F8A6-4D25-B2FC-07792E17957C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
 [2022-04-03 20:37:18.789] httpListenThread start ret=0
 [2022-04-03 20:37:48.790] start listen on 6060 ...
 [2022-04-03 20:43:49.717] setStartTimePoint total_tv_start_sys=438 total_tv_end_sys=439

2022-04-03 20:37:18 driver-btm-soc.c:6520:bitmain_soc_init: This is Antminer S9 SE scan user version
2022-04-03 20:37:18 driver-btm-soc.c:6526:bitmain_soc_init: special mode: disabled
2022-04-03 20:37:18 driver-btm-soc.c:6533:bitmain_soc_init: This is high performance mode
2022-04-03 20:37:18 driver-btm-soc.c:6538:bitmain_soc_init: last commit version: 99791ac commit time: 2019-09-17 19:17:44 build: 2019-09-18 16:00:29
2022-04-03 20:37:18 driver-btm-soc.c:6559:bitmain_soc_init: Detect 256MB control board of XILINX
2022-04-03 20:37:18 driver-btm-soc.c:6562:bitmain_soc_init: Miner compile time: Wed Sep 18 15:51:07 CST 2019 type: Antminer S9 SE
2022-04-03 20:37:18 driver-btm-soc.c:839:check_chain: get_hash_on_plug is 0x7
2022-04-03 20:37:18 driver-btm-soc.c:851:check_chain: !! chain[0]is exist
2022-04-03 20:37:18 driver-btm-soc.c:851:check_chain: !! chain[1]is exist
2022-04-03 20:37:18 driver-btm-soc.c:851:check_chain: !! chain[2]is exist
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fc 28 fc ff
00000080 ff ff ff ff ff ff ff a0   59 59 59 56 4e 54 4e 56
00000090 56 54 54 56 56 56 54 4e   59 59 59 4e 56 59 59 56
000000a0 56 4e 54 4e 59 54 4e 4e   54 54 56 56 56 59 59 59
000000b0 59 4e 59 59 56 56 56 54   54 4e 54 54 56 56 56 59
000000c0 4e 59 59 4e 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff a7 14 00 00   20 ff ff ff 39 10 be a9
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fc 28 fc ff
00000080 ff ff ff ff ff ff ff a0   59 59 59 56 4e 54 4e 56
00000090 56 54 54 56 56 56 54 4e   59 59 59 4e 56 59 59 56
000000a0 56 4e 54 4e 59 54 4e 4e   54 54 56 56 56 59 59 59
000000b0 59 4e 59 59 56 56 56 54   54 4e 54 54 56 56 56 59
000000c0 4e 59 59 4e 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff a7 14 00 00   20 ff ff ff 39 10 be a9
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fc 28 fc ff
00000080 ff ff ff ff ff ff ff a0   59 59 59 56 4e 54 4e 56
00000090 56 54 54 56 56 56 54 4e   59 59 59 4e 56 59 59 56
000000a0 56 4e 54 4e 59 54 4e 4e   54 54 56 56 56 59 59 59
000000b0 59 4e 59 59 56 56 56 54   54 4e 54 54 56 56 56 59
000000c0 4e 59 59 4e 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff a7 14 00 00   20 ff ff ff 39 10 be a9

read chain[0] hardware info:
major type: 0
minor type: 4
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[1] hardware info:
major type: 0
minor type: 4
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[2] hardware info:
major type: 0
minor type: 4
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

sweep config for eco mode:
sweep_start_voltage: 8.60
max_aging_voltage:   8.90
sweep_min_freq:      300M
sweep_max_freq:      380M

sweep config for hpf mode:
sweep_start_voltage: 9.20
max_aging_voltage:   9.50
sweep_min_freq:      415M
sweep_max_freq:      465M
2022-04-03 20:37:30 driver-btm-soc.c:839:check_chain: get_hash_on_plug is 0x7
2022-04-03 20:37:30 driver-btm-soc.c:851:check_chain: !! chain[0]is exist
2022-04-03 20:37:30 driver-btm-soc.c:851:check_chain: !! chain[1]is exist
2022-04-03 20:37:30 driver-btm-soc.c:851:check_chain: !! chain[2]is exist
2022-04-03 20:37:30 driver-btm-soc.c:5965:get_freq_result_from_eeprom: orginal chip freq:
chain 0 freq:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390

chain 1 freq:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390

chain 2 freq:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390

2022-04-03 20:37:30 driver-btm-soc.c:6647:bitmain_soc_init: reset all...
2022-04-03 20:37:32 driver-btm-soc.c:6655:bitmain_soc_init: miner ID : 805275025c208854
2022-04-03 20:37:32 driver-btm-soc.c:6359:init_miner_version: FPGA Version = 0xB00D
2022-04-03 20:37:52 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[0] PIC software version: 177
2022-04-03 20:37:52 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[1] PIC software version: 177
2022-04-03 20:37:53 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[2] PIC software version: 177
2022-04-03 20:37:53 power.c:185:power_init: power init ...
2022-04-03 20:37:53 driver-btm-soc.c:5060:get_working_voltage_from_eeprom: get working vol [ 9.50] from chain[0] eeprom
2022-04-03 20:37:53 power.c:232:set_working_voltage_by_chain: chain[0] working_voltage = 9.50
2022-04-03 20:37:53 driver-btm-soc.c:5060:get_working_voltage_from_eeprom: get working vol [ 9.50] from chain[1] eeprom
2022-04-03 20:37:53 power.c:232:set_working_voltage_by_chain: chain[1] working_voltage = 9.50
2022-04-03 20:37:53 driver-btm-soc.c:5060:get_working_voltage_from_eeprom: get working vol [ 9.50] from chain[2] eeprom
2022-04-03 20:37:53 power.c:232:set_working_voltage_by_chain: chain[2] working_voltage = 9.50
2022-04-03 20:37:53 driver-btm-soc.c:5754:update_highest_voltage: chain 0 hpf working voltage 9.20
2022-04-03 20:37:53 driver-btm-soc.c:5754:update_highest_voltage: chain 1 hpf working voltage 9.20
2022-04-03 20:37:53 driver-btm-soc.c:5754:update_highest_voltage: chain 2 hpf working voltage 9.20
2022-04-03 20:37:53 driver-btm-soc.c:5763:update_highest_voltage: open core at max voltage 9.94
2022-04-03 20:37:53 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[0] setting to highest voltage: 09.94 ...
2022-04-03 20:37:53 power.c:707:set_iic_power_by_voltage: now setting voltage to : 09.94
2022-04-03 20:37:54 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[1] setting to highest voltage: 09.94 ...
2022-04-03 20:37:56 power.c:707:set_iic_power_by_voltage: now setting voltage to : 09.94
2022-04-03 20:37:56 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[2] setting to highest voltage: 09.94 ...
2022-04-03 20:37:57 power.c:707:set_iic_power_by_voltage: now setting voltage to : 09.94
2022-04-03 20:37:57 driver-btm-soc.c:1188:get_eeprom_total_hash_rate: chain[0] hash rate = 5287
2022-04-03 20:37:57 driver-btm-soc.c:1188:get_eeprom_total_hash_rate: chain[1] hash rate = 5287
2022-04-03 20:37:57 driver-btm-soc.c:1188:get_eeprom_total_hash_rate: chain[2] hash rate = 5287
2022-04-03 20:37:57 driver-btm-soc.c:1192:get_eeprom_total_hash_rate: total rate = 15861
2022-04-03 20:37:57 driver-btm-soc.c:1200:get_ideal_hash_rate: get ideal hash rate 15000
2022-04-03 20:37:57 eeprom.c:669:travel_eeprom_store: chain[0] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:445 IC[001]:445 IC[002]:445 IC[003]:430 IC[004]:390 IC[005]:420 IC[006]:390 IC[007]:430 IC[008]:430 IC[009]:420
IC[010]:420 IC[011]:430 IC[012]:430 IC[013]:430 IC[014]:420 IC[015]:390 IC[016]:445 IC[017]:445 IC[018]:445 IC[019]:390
IC[020]:430 IC[021]:445 IC[022]:445 IC[023]:430 IC[024]:430 IC[025]:390 IC[026]:420 IC[027]:390 IC[028]:445 IC[029]:420
IC[030]:390 IC[031]:390 IC[032]:420 IC[033]:420 IC[034]:430 IC[035]:430 IC[036]:430 IC[037]:445 IC[038]:445 IC[039]:445
IC[040]:445 IC[041]:390 IC[042]:445 IC[043]:445 IC[044]:430 IC[045]:430 IC[046]:430 IC[047]:420 IC[048]:420 IC[049]:390
IC[050]:420 IC[051]:420 IC[052]:430 IC[053]:430 IC[054]:430 IC[055]:445 IC[056]:390 IC[057]:445 IC[058]:445 IC[059]:390
voltage in mode2: 9.20 V
hash rate in mode2: 05287 GH/s

2022-04-03 20:37:57 eeprom.c:669:travel_eeprom_store: chain[1] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:445 IC[001]:445 IC[002]:445 IC[003]:430 IC[004]:390 IC[005]:420 IC[006]:390 IC[007]:430 IC[008]:430 IC[009]:420
IC[010]:420 IC[011]:430 IC[012]:430 IC[013]:430 IC[014]:420 IC[015]:390 IC[016]:445 IC[017]:445 IC[018]:445 IC[019]:390
IC[020]:430 IC[021]:445 IC[022]:445 IC[023]:430 IC[024]:430 IC[025]:390 IC[026]:420 IC[027]:390 IC[028]:445 IC[029]:420
IC[030]:390 IC[031]:390 IC[032]:420 IC[033]:420 IC[034]:430 IC[035]:430 IC[036]:430 IC[037]:445 IC[038]:445 IC[039]:445
IC[040]:445 IC[041]:390 IC[042]:445 IC[043]:445 IC[044]:430 IC[045]:430 IC[046]:430 IC[047]:420 IC[048]:420 IC[049]:390
IC[050]:420 IC[051]:420 IC[052]:430 IC[053]:430 IC[054]:430 IC[055]:445 IC[056]:390 IC[057]:445 IC[058]:445 IC[059]:390
voltage in mode2: 9.20 V
hash rate in mode2: 05287 GH/s

2022-04-03 20:37:57 eeprom.c:669:travel_eeprom_store: chain[2] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:445 IC[001]:445 IC[002]:445 IC[003]:430 IC[004]:390 IC[005]:420 IC[006]:390 IC[007]:430 IC[008]:430 IC[009]:420
IC[010]:420 IC[011]:430 IC[012]:430 IC[013]:430 IC[014]:420 IC[015]:390 IC[016]:445 IC[017]:445 IC[018]:445 IC[019]:390
IC[020]:430 IC[021]:445 IC[022]:445 IC[023]:430 IC[024]:430 IC[025]:390 IC[026]:420 IC[027]:390 IC[028]:445 IC[029]:420
IC[030]:390 IC[031]:390 IC[032]:420 IC[033]:420 IC[034]:430 IC[035]:430 IC[036]:430 IC[037]:445 IC[038]:445 IC[039]:445
IC[040]:445 IC[041]:390 IC[042]:445 IC[043]:445 IC[044]:430 IC[045]:430 IC[046]:430 IC[047]:420 IC[048]:420 IC[049]:390
IC[050]:420 IC[051]:420 IC[052]:430 IC[053]:430 IC[054]:430 IC[055]:445 IC[056]:390 IC[057]:445 IC[058]:445 IC[059]:390
voltage in mode2: 9.20 V
hash rate in mode2: 05287 GH/s

2022-04-03 20:37:57 driver-btm-soc.c:6698:bitmain_soc_init: fan_eft : 0  fan_pwm : 0
2022-04-03 20:37:57 driver-btm-soc.c:6388:bring_up_chain:

bring up chain 0
2022-04-03 20:37:58 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2022-04-03 20:38:30 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2022-04-03 20:38:31 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 0, find asic num = 60
2022-04-03 20:38:34 driver-btm-soc.c:4816:set_freq_by_chain: chain[0] set freq:100.00
2022-04-03 20:38:35 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 0
2022-04-03 20:38:35 driver-btm-soc.c:4090:set_clock_delay_control: core_data = 0x06
2022-04-03 20:38:35 temperature.c:614:is_eeprom_tempsensor_data_correct: sensor_num 2, sensor pos = 31, 40, 0, 0
2022-04-03 20:38:35 temperature.c:523:is_tempsensor_data_correct: Bad,temp_info.type = 0
2022-04-03 20:38:35 temperature.c:751:calibration_sensor_offset: chain[0] temp info is bad, reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0
sensor offset: -4  -4  0  0  0  0
2022-04-03 20:38:35 temperature.c:801:calibration_sensor_offset: Chain[0] chip[31] middle temp offset=-4, typeID=55
2022-04-03 20:38:36 temperature.c:801:calibration_sensor_offset: Chain[0] chip[40] middle temp offset=-4, typeID=55
2022-04-03 20:38:36 driver-btm-soc.c:6388:bring_up_chain:

bring up chain 1
2022-04-03 20:38:37 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2022-04-03 20:39:09 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2022-04-03 20:39:10 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 1, find asic num = 60
2022-04-03 20:39:13 driver-btm-soc.c:4816:set_freq_by_chain: chain[1] set freq:100.00
2022-04-03 20:39:14 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 1
2022-04-03 20:39:14 driver-btm-soc.c:4090:set_clock_delay_control: core_data = 0x06
2022-04-03 20:39:14 temperature.c:614:is_eeprom_tempsensor_data_correct: sensor_num 2, sensor pos = 31, 40, 0, 0
2022-04-03 20:39:14 temperature.c:523:is_tempsensor_data_correct: Bad,temp_info.type = 0
2022-04-03 20:39:14 temperature.c:751:calibration_sensor_offset: chain[1] temp info is bad, reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0
sensor offset: -4  -4  0  0  0  0
2022-04-03 20:39:15 temperature.c:801:calibration_sensor_offset: Chain[1] chip[31] middle temp offset=-4, typeID=55
2022-04-03 20:39:15 temperature.c:801:calibration_sensor_offset: Chain[1] chip[40] middle temp offset=-4, typeID=55
2022-04-03 20:39:15 driver-btm-soc.c:6388:bring_up_chain:

bring up chain 2
2022-04-03 20:39:16 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2022-04-03 20:39:48 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-03 20:39:49 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 2, find asic num = 60
2022-04-03 20:39:53 driver-btm-soc.c:4816:set_freq_by_chain: chain[2] set freq:100.00
2022-04-03 20:39:53 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 2
2022-04-03 20:39:53 driver-btm-soc.c:4090:set_clock_delay_control: core_data = 0x06
2022-04-03 20:39:53 temperature.c:614:is_eeprom_tempsensor_data_correct: sensor_num 2, sensor pos = 31, 40, 0, 0
2022-04-03 20:39:53 temperature.c:523:is_tempsensor_data_correct: Bad,temp_info.type = 0
2022-04-03 20:39:53 temperature.c:751:calibration_sensor_offset: chain[2] temp info is bad, reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0
sensor offset: -4  -4  0  0  0  0
2022-04-03 20:39:54 temperature.c:801:calibration_sensor_offset: Chain[2] chip[31] middle temp offset=-4, typeID=55
2022-04-03 20:39:54 temperature.c:801:calibration_sensor_offset: Chain[2] chip[40] middle temp offset=-4, typeID=55
2022-04-03 20:39:55 asic.c:1153:set_baud: set baud=1
2022-04-03 20:39:55 asic.c:1269:set_asic_ticket_mask: set ticket mask 63
2022-04-03 20:39:56 temperature.c:2064:detect_startup_environment_temperature: Environment temperature: [33]
2022-04-03 20:39:56 temperature.c:2081:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 1 times ...
2022-04-03 20:40:07 temperature.c:2064:detect_startup_environment_temperature: Environment temperature: [33]
2022-04-03 20:40:07 temperature.c:2081:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 2 times ...
2022-04-03 20:40:18 temperature.c:2064:detect_startup_environment_temperature: Environment temperature: [33]
2022-04-03 20:40:18 temperature.c:2081:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 3 times ...
2022-04-03 20:40:28 driver-btm-soc.c:4160:open_core_bm1393: Start Open Core!!
2022-04-03 20:40:34 driver-btm-soc.c:4227:open_core_bm1393: End Open Core!!
2022-04-03 20:40:35 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 125
2022-04-03 20:40:37 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 150
2022-04-03 20:40:39 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 175
2022-04-03 20:40:42 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 200
2022-04-03 20:40:44 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 225
2022-04-03 20:40:46 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 250
2022-04-03 20:40:48 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 275
2022-04-03 20:40:50 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 300
2022-04-03 20:40:52 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 325
2022-04-03 20:40:54 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 350
2022-04-03 20:40:56 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 375
2022-04-03 20:40:59 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 390
2022-04-03 20:41:01 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 445 ,min = 390
2022-04-03 20:41:01 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[0] increaseing the diff freq ...
2022-04-03 20:41:11 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 0 final freq setting:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390
2022-04-03 20:41:11 power.c:1309:slowly_set_working_power_t11: set chain 0 to working voltage:
now setting chain[0]-volt[09.89]-data[017]
now setting chain[0]-volt[09.80]-data[019]
now setting chain[0]-volt[09.72]-data[021]
now setting chain[0]-volt[09.65]-data[023]
now setting chain[0]-volt[09.58]-data[025]
now setting chain[0]-volt[09.54]-data[026]
now setting chain[0]-volt[09.51]-data[027]
2022-04-03 20:41:40 power.c:1331:slowly_set_working_power_t11: done!
2022-04-03 20:41:40 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 125
2022-04-03 20:41:42 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 150
2022-04-03 20:41:44 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 175
2022-04-03 20:41:46 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 200
2022-04-03 20:41:49 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 225
2022-04-03 20:41:51 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 250
2022-04-03 20:41:53 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 275
2022-04-03 20:41:55 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 300
2022-04-03 20:41:57 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 325
2022-04-03 20:41:59 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 350
2022-04-03 20:42:01 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 375
2022-04-03 20:42:03 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 390
2022-04-03 20:42:05 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 445 ,min = 390
2022-04-03 20:42:05 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[1] increaseing the diff freq ...
2022-04-03 20:42:16 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 1 final freq setting:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390
2022-04-03 20:42:16 power.c:1309:slowly_set_working_power_t11: set chain 1 to working voltage:
now setting chain[1]-volt[09.89]-data[017]
now setting chain[1]-volt[09.80]-data[019]
now setting chain[1]-volt[09.72]-data[021]
now setting chain[1]-volt[09.65]-data[023]
now setting chain[1]-volt[09.58]-data[025]
now setting chain[1]-volt[09.54]-data[026]
now setting chain[1]-volt[09.51]-data[027]
2022-04-03 20:42:45 power.c:1331:slowly_set_working_power_t11: done!
2022-04-03 20:42:45 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 125
2022-04-03 20:42:48 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 150
2022-04-03 20:42:50 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 175
2022-04-03 20:42:52 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 200
2022-04-03 20:42:54 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 225
2022-04-03 20:42:56 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 250
2022-04-03 20:42:58 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 275
2022-04-03 20:43:00 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 300
2022-04-03 20:43:02 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 325
2022-04-03 20:43:05 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 350
2022-04-03 20:43:07 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 375
2022-04-03 20:43:09 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[2] increase to 390
2022-04-03 20:43:11 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 445 ,min = 390
2022-04-03 20:43:11 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[2] increaseing the diff freq ...
2022-04-03 20:43:22 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 2 final freq setting:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390
2022-04-03 20:43:22 power.c:1309:slowly_set_working_power_t11: set chain 2 to working voltage:
now setting chain[2]-volt[09.89]-data[017]
now setting chain[2]-volt[09.80]-data[019]
now setting 2022-04-03 20:43:33 dspic33ep16gs202.c:276:dsPIC33EP16GS202_set_pic_voltage: ERROR! failed on Chain[2] after 3 times try!
chain[2]-volt[09.72]-data[021]
now setting chain[2]-volt[09.65]-data[023]
now setting chain[2]-volt[09.58]-data[025]
now setting 2022-04-03 20:43:45 dspic33ep16gs202.c:276:dsPIC33EP16GS202_set_pic_voltage: ERROR! failed on Chain[2] after 3 times try!
chain[2]-volt[09.54]-data[026]
now setting chain[2]-volt[09.51]-data[027]
2022-04-03 20:43:49 power.c:1331:slowly_set_working_power_t11: done!
2022-04-03 20:43:49 driver-btm-soc.c:5112:set_timeout: freq 445 final timeout=294
2022-04-03 20:43:49 driver-btm-soc.c:2920:low_temp_process_parm_init: chip miner_type = [4]
2022-04-03 20:43:49 driver-btm-soc.c:2920:low_temp_process_parm_init: chip miner_type = [4]
2022-04-03 20:43:49 driver-btm-soc.c:2920:low_temp_process_parm_init: chip miner_type = [4]
2022-04-03 20:43:49 driver-btm-soc.c:3359:check_system_work: check system thread start...
2022-04-03 20:43:49 driver-btm-soc.c:3376:check_system_work: low_bringup_pcb_temp_threshhold = 28
2022-04-03 20:43:49 driver-btm-soc.c:3377:check_system_work: recovery_working_vol_low_temp = 30, recovery_working_vol_high_temp = 35
2022-04-03 20:43:49 driver-btm-soc.c:3378:check_system_work: delta_voltage = 0.10
2022-04-03 20:43:49 driver-btm-soc.c:6810:bitmain_soc_init: Init done!
2022-04-03 20:43:49 driver-btm-soc.c:7429:bitmain_soc_prepare: bitmain soc init success.
2022-04-03 20:43:50 temperature.c:1525:read_temp_func: bring_up_pcb_temp = 39
2022-04-03 20:43:55 util.c:2178:process_version_mask: Pool 0 Version num is 2
2022-04-03 20:43:55 driver-btm-soc.c:7104:send_job: Version num 2
2022-04-03 20:44:08 driver-btm-soc.c:3541:check_system_work: set reopen algorith parameters...
2022-04-03 20:47:51 driver-btm-soc.c:3279:decrease_voltage_at_high_temp: decrease volt for max chip temp is 96
2022-04-03 20:47:51 power.c:246:set_customer_voltage_by_chain: chain[0] customer_voltage = 9.30
2022-04-03 20:47:51 power.c:246:set_customer_voltage_by_chain: chain[1] customer_voltage = 9.30
2022-04-03 20:47:51 power.c:246:set_customer_voltage_by_chain: chain[2] customer_voltage = 9.30
2022-04-03 20:47:51 power.c:1258:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage:
now setting chain[0]-volt[09.48]-data[028] chain[1]-volt[09.48]-data[028] chain[2]-volt[09.48]-data[028]
now setting chain[0]-volt[09.45]-data[029] chain[1]-volt[09.45]-data[029] chain[2]-volt[09.45]-data[029]
now setting chain[0]-volt[09.42]-data[030] chain[1]-volt[09.42]-data[030] chain[2]-volt[09.42]-data[030]
now setting chain[0]-volt[09.39]-data[031] chain[1]-volt[09.39]-data[031] chain[2]-volt[09.39]-data[031]
now setting chain[0]-volt[09.37]-data[032] chain[1]-volt[09.37]-data[032] chain[2]-volt[09.37]-data[032]
now setting chain[0]-volt[09.34]-data[033] chain[1]-volt[09.34]-data[033] chain[2]-volt[09.34]-data[033]
now setting chain[0]-volt[09.32]-data[034] chain[1]-volt[09.32]-data[034] chain[2]-volt[09.32]-data[034]
2022-04-03 20:48:11 power.c:1278:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage end!
now setting chain[0]-volt[09.30]-data[034] chain[1]-volt[09.30]-data[034] chain[2]-volt[09.30]-data[034]
2022-04-03 20:49:11 eeprom.c:917:eeprom_get_inbalance_info: error: chain[0] inbalance num is 255, more than MAX_OFFSET 4
2022-04-03 20:49:11 driver-btm-soc.c:2500:is_domain_imbalance: eeprom info not correct! ret = 0, len = 0
2022-04-03 20:49:11 eeprom.c:917:eeprom_get_inbalance_info: error: chain[1] inbalance num is 255, more than MAX_OFFSET 4
2022-04-03 20:49:11 driver-btm-soc.c:2500:is_domain_imbalance: eeprom info not correct! ret = 0, len = 0
2022-04-03 20:49:11 eeprom.c:917:eeprom_get_inbalance_info: error: chain[2] inbalance num is 255, more than MAX_OFFSET 4
2022-04-03 20:49:11 driver-btm-soc.c:2500:is_domain_imbalance: eeprom info not correct! ret = 0, len = 0
2022-04-03 20:49:11 driver-btm-soc.c:2513:is_domain_imbalance: dumping inbalance domain info...
0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  
0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  0 0 0 0  
2022-04-03 21:14:35 driver-btm-soc.c:3510:check_system_work: The avg rate is  15355 in 30 mins, PCB temperature between 39 ~ 74
2022-04-03 21:45:03 driver-btm-soc.c:3510:check_system_work: The avg rate is  15467 in 30 mins, PCB temperature between 40 ~ 74
2022-04-03 22:15:31 driver-btm-soc.c:3510:check_system_work: The avg rate is  15457 in 30 mins, PCB temperature between 40 ~ 75
2022-04-03 22:46:00 driver-btm-soc.c:3510:check_system_work: The avg rate is  15433 in 30 mins, PCB temperature between 41 ~ 75
2022-04-03 23:16:28 driver-btm-soc.c:3510:check_system_work: The avg rate is  15522 in 30 mins, PCB temperature between 41 ~ 75
2022-04-03 23:46:57 driver-btm-soc.c:3510:check_system_work: The avg rate is  15372 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 00:17:26 driver-btm-soc.c:3510:check_system_work: The avg rate is  15497 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 00:32:40 driver-btm-soc.c:3555:check_system_work:  start to reopen
2022-04-04 00:32:40 driver-btm-soc.c:6911:re_open_core_by_chain:

reopen chain 0, current pwm 100
2022-04-04 00:32:42 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[0] setting to highest voltage: 09.94 ...
2022-04-04 00:32:42 power.c:707:set_iic_power_by_voltage: now setting voltage to : 09.94
2022-04-04 00:32:43 asic.c:1176:set_baud_by_chain: chain 0 set baud=26
2022-04-04 00:32:43 driver-btm-soc.c:6388:bring_up_chain:

bring up chain 0
2022-04-04 00:32:43 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff9
2022-04-04 00:32:44 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-04 00:32:45 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 0, find asic num = 60
2022-04-04 00:32:48 driver-btm-soc.c:4816:set_freq_by_chain: chain[0] set freq:100.00
2022-04-04 00:32:49 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 0
2022-04-04 00:32:49 driver-btm-soc.c:4090:set_clock_delay_control: core_data = 0x06
2022-04-04 00:32:49 temperature.c:614:is_eeprom_tempsensor_data_correct: sensor_num 2, sensor pos = 31, 40, 0, 0
2022-04-04 00:32:50 temperature.c:801:calibration_sensor_offset: Chain[0] chip[31] middle temp offset=-4, typeID=55
2022-04-04 00:32:50 temperature.c:801:calibration_sensor_offset: Chain[0] chip[40] middle temp offset=-4, typeID=55
2022-04-04 00:32:50 asic.c:1176:set_baud_by_chain: chain 0 set baud=1
2022-04-04 00:32:51 asic.c:1269:set_asic_ticket_mask: set ticket mask 63
2022-04-04 00:32:51 driver-btm-soc.c:4160:open_core_bm1393: Start Open Core!!
2022-04-04 00:32:53 driver-btm-soc.c:4227:open_core_bm1393: End Open Core!!
2022-04-04 00:32:53 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 125
2022-04-04 00:32:55 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 150
2022-04-04 00:32:57 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 175
2022-04-04 00:32:59 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 200
2022-04-04 00:33:01 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 225
2022-04-04 00:33:03 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 250
2022-04-04 00:33:05 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 275
2022-04-04 00:33:08 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 300
2022-04-04 00:33:10 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 325
2022-04-04 00:33:12 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 350
2022-04-04 00:33:14 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 375
2022-04-04 00:33:16 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[0] increase to 390
2022-04-04 00:33:18 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 445 ,min = 390
2022-04-04 00:33:18 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[0] increaseing the diff freq ...
2022-04-04 00:33:29 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 0 final freq setting:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390
2022-04-04 00:33:29 driver-btm-soc.c:5112:set_timeout: freq 445 final timeout=294
2022-04-04 00:33:30 driver-btm-soc.c:6938:re_open_core_by_chain: reopen chain 0 finished, chain 0 chip temp 66 - 86
2022-04-04 00:33:30 driver-btm-soc.c:6939:re_open_core_by_chain: all chain chip temp 65 - 98
2022-04-04 00:33:30 power.c:996:slowly_set_iic_power_to_working_voltage_by_chain: chain[0] slowly setting to voltage: 09.50 ...
2022-04-04 00:33:31 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.94
2022-04-04 00:33:37 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.89
2022-04-04 00:33:40 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.80
2022-04-04 00:33:43 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.72
2022-04-04 00:33:47 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.65
2022-04-04 00:33:48 dspic33ep16gs202.c:213:dsPIC33EP16GS202_pic_heart_beat: ERROR! failed on Chain[0] after 3 times try!
2022-04-04 00:33:52 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.58
2022-04-04 00:33:55 power.c:728:set_iic_power_by_iic_data: now setting voltage to : 09.54
2022-04-04 00:33:56 driver-btm-soc.c:6955:re_open_core_by_chain: re_open_core done!
2022-04-04 00:34:26 driver-btm-soc.c:6911:re_open_core_by_chain:

reopen chain 1, current pwm 100
2022-04-04 00:34:29 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[1] setting to highest voltage: 09.94 ...
2022-04-04 00:34:30 power.c:707:set_iic_power_by_voltage: now setting voltage to : 09.94
2022-04-04 00:34:30 asic.c:1176:set_baud_by_chain: chain 1 set baud=26
2022-04-04 00:34:30 driver-btm-soc.c:6388:bring_up_chain:

bring up chain 1
2022-04-04 00:34:30 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffa
2022-04-04 00:34:31 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-04 00:34:33 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 1, find asic num = 59
2022-04-04 00:34:33 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffa
2022-04-04 00:34:34 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-04 00:34:37 driver-btm-soc.c:4003:check_asic_num: without pre_open_core chain 1, find asic num = 59
2022-04-04 00:34:37 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffa
2022-04-04 00:34:38 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-04 00:34:39 driver-btm-soc.c:4011:check_asic_num: check asic num with pre_open_core
2022-04-04 00:34:39 driver-btm-soc.c:3976:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 0
2022-04-04 00:34:39 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffa
2022-04-04 00:34:40 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-04 00:34:41 driver-btm-soc.c:3944:check_asic_num_without_power_off: Open 5 core for chain 1
2022-04-04 00:34:41 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 1
2022-04-04 00:34:43 driver-btm-soc.c:3950:check_asic_num_without_power_off: chain 1, find asic num = 59
2022-04-04 00:34:43 driver-btm-soc.c:3976:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 1
2022-04-04 00:34:43 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffa
2022-04-04 00:34:44 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2022-04-04 00:34:45 driver-btm-soc.c:3944:check_asic_num_without_power_off: Open 5 core for chain 1
2022-04-04 00:34:45 driver-btm-soc.c:3929:pre_open_core_one_chain: for chain 1
2022-04-04 00:34:46 driver-btm-soc.c:3950:check_asic_num_without_power_off: chain 1, find asic num = 59
2022-04-04 00:34:47 driver-btm-soc.c:4033:check_asic_num: chian 1 check asic number failed!
2022-04-04 00:34:47 asic.c:1176:set_baud_by_chain: chain 1 set baud=1
2022-04-04 00:34:47 asic.c:1269:set_asic_ticket_mask: set ticket mask 63
2022-04-04 00:34:47 driver-btm-soc.c:4160:open_core_bm1393: Start Open Core!!
2022-04-04 00:34:47 driver-btm-soc.c:4227:open_core_bm1393: End Open Core!!
2022-04-04 00:34:47 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 125
2022-04-04 00:34:49 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 150
2022-04-04 00:34:51 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 175
2022-04-04 00:34:52 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 200
2022-04-04 00:34:54 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 225
2022-04-04 00:34:56 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 250
2022-04-04 00:34:58 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 275
2022-04-04 00:34:59 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 300
2022-04-04 00:35:01 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 325
2022-04-04 00:35:03 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 350
2022-04-04 00:35:05 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 375
2022-04-04 00:35:06 driver-btm-soc.c:5367:increase_freq_by_eeprom_slowly_by_chain: chain[1] increase to 390
2022-04-04 00:35:08 driver-btm-soc.c:5383:increase_freq_by_eeprom_slowly_by_chain: max = 445 ,min = 390
2022-04-04 00:35:08 driver-btm-soc.c:5389:increase_freq_by_eeprom_slowly_by_chain: chain[1] increaseing the diff freq ...
2022-04-04 00:35:16 driver-btm-soc.c:5418:increase_freq_by_eeprom_slowly_by_chain: chain 1 final freq setting:
445 445 445 430 390 420 390 430 430 420
420 430 430 430 420 390 445 445 445 390
430 445 445 430 430 390 420 390 445 420
390 390 420 420 430 430 430 445 445 445
445 390 445 445 430 430 430 420 420 390
420 420 430 430 430 445 390 445 445 390
2022-04-04 00:35:16 driver-btm-soc.c:5112:set_timeout: freq 445 final timeout=294
2022-04-04 00:35:17 driver-btm-soc.c:6938:re_open_core_by_chain: reopen chain 1 finished, chain 1 chip temp 73 - 94
2022-04-04 00:35:17 driver-btm-soc.c:6939:re_open_core_by_chain: all chain chip temp 64 - 96
2022-04-04 00:35:17 power.c:988:slowly_set_iic_power_to_working_voltage_by_chain: error! chain[1] does not exist!
2022-04-04 00:35:17 driver-btm-soc.c:6955:re_open_core_by_chain: re_open_core done!
2022-04-04 00:35:47 driver-btm-soc.c:3646:check_system_work: Reboot cost 187 sec !
2022-04-04 00:35:47 driver-btm-soc.c:3657:check_system_work: re_open_core [1] times!
2022-04-04 00:35:47 power.c:1258:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage:
now setting chain[0]-volt[09.51]-data[027] chain[2]-volt[09.51]-data[027]
2022-04-04 00:35:49 power.c:1278:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage end!
now setting chain[0]-volt[09.50]-data[027] chain[2]-volt[09.50]-data[027]
2022-04-04 00:51:03 driver-btm-soc.c:3510:check_system_work: The avg rate is  11522 in 30 mins, PCB temperature between 41 ~ 76
2022-04-04 01:21:30 driver-btm-soc.c:3510:check_system_work: The avg rate is  10375 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 01:51:58 driver-btm-soc.c:3510:check_system_work: The avg rate is  10278 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 02:22:26 driver-btm-soc.c:3510:check_system_work: The avg rate is  10228 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 02:52:54 driver-btm-soc.c:3510:check_system_work: The avg rate is  10252 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 03:23:22 driver-btm-soc.c:3510:check_system_work: The avg rate is  10340 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 03:53:50 driver-btm-soc.c:3510:check_system_work: The avg rate is  10359 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 04:24:18 driver-btm-soc.c:3510:check_system_work: The avg rate is  10202 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 04:54:45 driver-btm-soc.c:3510:check_system_work: The avg rate is  10208 in 30 mins, PCB temperature between 41 ~ 75
2022-04-04 05:25:13 driver-btm-soc.c:3510:check_system_work: The avg rate is  10270 in 30 mins, PCB temperature between 42 ~ 75
2022-04-04 05:55:40 driver-btm-soc.c:3510:check_system_work: The avg rate is  10245 in 30 mins, PCB temperature between 42 ~ 75
2022-04-04 06:26:08 driver-btm-soc.c:3510:check_system_work: The avg rate is  10325 in 30 mins, PCB temperature between 42 ~ 76
2022-04-04 06:56:36 driver-btm-soc.c:3510:check_system_work: The avg rate is  10180 in 30 mins, PCB temperature between 42 ~ 76
2022-04-04 07:27:04 driver-btm-soc.c:3510:check_system_work: The avg rate is  10216 in 30 mins, PCB temperature between 42 ~ 76
2022-04-04 07:57:32 driver-btm-soc.c:3510:check_system_work: The avg rate is  10171 in 30 mins, PCB temperature between 42 ~ 76
2022-04-04 08:28:00 driver-btm-soc.c:3510:check_system_work: The avg rate is  10216 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 08:58:28 driver-btm-soc.c:3510:check_system_work: The avg rate is  10070 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 09:28:55 driver-btm-soc.c:3510:check_system_work: The avg rate is  10206 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 09:59:23 driver-btm-soc.c:3510:check_system_work: The avg rate is  10319 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 10:29:51 driver-btm-soc.c:3510:check_system_work: The avg rate is  10189 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 11:00:19 driver-btm-soc.c:3510:check_system_work: The avg rate is  10302 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 11:30:46 driver-btm-soc.c:3510:check_system_work: The avg rate is  10141 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 12:01:14 driver-btm-soc.c:3510:check_system_work: The avg rate is  10266 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 12:31:42 driver-btm-soc.c:3510:check_system_work: The avg rate is  10219 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 13:02:10 driver-btm-soc.c:3510:check_system_work: The avg rate is  10080 in 30 mins, PCB temperature between 43 ~ 78
2022-04-04 13:32:38 driver-btm-soc.c:3510:check_system_work: The avg rate is  10114 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 14:03:06 driver-btm-soc.c:3510:check_system_work: The avg rate is  10318 in 30 mins, PCB temperature between 43 ~ 77
2022-04-04 14:33:33 driver-btm-soc.c:3510:check_system_work: The avg rate is  10136 in 30 mins, PCB temperature between 43 ~ 77