Topic: L3+ Way Overclocked! 500M frequency - 650 MH/s! - page 3. (Read 3017 times)

Don't do that you will kill a board soooo fast

https://ibb.co/hQ6V0w
Dont know how to get it to show pic in post.

And I wrote and quoted (partially above) I have had my L3 plus for almost 90 days now so if something should go wrong I believe the time it would take to get it repaired would wipe out Most of the games games as the profits / income or decreasing greatly Even if I hadnt voided the warranty. I figured the +20 to 25% in hash power was worth the risk and thus far has been.

 I didn’t get my batch and until late September I believe. The lesson I’ve learned is to get in the first batch or don’t get in at all. Although I think I will eventually make profit with this primarily due to the increase  in value of the coin’s. I’ll have to do a calculation later to figure out if it would produce 45 LTC  for the L3 plus and the power supply adjusting for electric cost.

 I believe my experimentation warrants even a small tip and  I would be happy with pennies just to say I got a tip.  I recently registered my ENS (Ethereum Name Service) for ETH.  Most wallets including myetherwallet support it.  Someone do me a favor and verify I set it up right and send me a couple US cent (or a few ETH lol) to Rexmint.eth

Just type Rexmint.eth in the address to field And the wallet should do the rest and there is no need to type out a long string of letters and numbers. I think it’s a really neat service something on the surprise BTC haven’t done yet

What about warranty?
bitmain didn't accept overclocked machines

 I will upload photos tonight

 Sorry I may have not been as specific as needed.

The L3+ comes at stock set at 384M frequency (I think) which equals out to approximately 504 MH/S.

My first overclock I had it going around 600 MH/and I believe that was at 440-460 frequency.

As you can see in my post where I outlined the settings I have overclocked it to 500 frequency which is given me approximately 650 MH/S.

My question is if anyone has set a frequency of 500 or higher and if so if they have seen any issues? The only issue I see currently is the high HW account but at least according to nice hash it is reporting all my shares are 100% accepted and my temperatures appear to be at par with stocks settings?

Any long term issues with constant high H.W.?

The L3+ is advertized at 504MH/s stock. i have mine overclocked to 576MH/s. Do you mean 600MH/s?

I was planning on running my L3+ at 500M for 24 hours but my power went out about 18 hours so Ill run the test again starting now. Just started about 6 mins ago.

Here is what I got so far....

Summary
Elapsed 22m14s
MH/S(RT) 653.014
MH/S(avg) 614.46
FoundBlocks 0
LocalWork 1,304
Utility 1.80
WU 554,176.67
BestShare 10558902

Pools
Pool - URL - User - Status - Diff - GetWorks - Priority - Accepted - Nonce# - DiffA# - DiffR# - DiffS# - Rejected - Discard - Stale - LSTime
0 - stratum+tcp://scrypt.usa.nicehash.com:3333 - 3CpwE7z4wxJ696B518qjq7HRUngzFrXjMS.rexrig1 - Alive - 262K - 25 - 0 - 0 - 0 - 235 - 0 - 524,288 - 0:00:49
** Pool 1 (stratum+tcp://prohashing.com:3333) and 2 (stratum+tcp://us.litecoinpool.org:3333) all have the same data except "User", "Priority" has 1 for Pool 1 and 2 Pool 2.

AntMiner
Chain# - ASIC# - Frequency - MH/S(RT) - HW - Temp(PCB) - Temp(Chip) -ASIC status
1 72 500 163.02 191 I0 O49 I059 *all o"s
2 72 500 163.07 179 I0 O46 I055 *all o"s
3 72 500 163.63 307 I0 O45 I054 *all o"s
4 72 500 163.73 164 I0 O44 I053 *all o"s

Fan#   Speed (r/min)
Fan1 3,390
Fan2 3,420

-----

Okay and here is the readout after I got done writing, coping and pasting....

Summary
Elapsed 6m35s
MH/S(RT) 653.463
MH/S(avg) 605.71
FoundBlocks 0
LocalWork 413
Utility 1.37
WU 636,807.48
BestShare 7810993

Pools
Pool - URL - User - Status - Diff - GetWorks - Priority - Accepted - Nonce# - DiffA# - DiffR# - DiffS# - Rejected - Discard - Stale - LSTime
0 - stratum+tcp://scrypt.usa.nicehash.com:3333 - 3CpwE7z4wxJ696B518qjq7HRUngzFrXjMS.rexrig1 - Alive - 262K - 69 - 0 - 0 - 0 - 769 - 0 - 262,144 - 0:00:06
** Pool 1 (stratum+tcp://prohashing.com:3333) and 2 (stratum+tcp://us.litecoinpool.org:3333) all have the same data except "User", "Priority" has 1 for Pool 1 and 2 Pool 2.

AntMiner
Chain# - ASIC# - Frequency - MH/S(RT) - HW - Temp(PCB) - Temp(Chip) -ASIC status
1 72 500 163.17 723 I0 O48 I059 *all o"s
2 72 500 163.66 633 I0 O45 I054 *all o"s
3 72 500 163.02 1026 I0 O45 I054 *all o"s
4 72 500 163.16 587 I0 O44 I052 *all o"s

Fan#   Speed (r/min)
Fan1 3,390
Fan2 3,450

----------------------------------

I will get a KillAWatt reading later.

Likie I said I did have this running for almost 20 hours before my power went out on me.

If anyone could refer me to a guide so I can firgure out what everything means like "DiffS" and "DiffA" and all the rest I would appreciate it.

I have been earning about $1-1.25 per on NH with these settings. ProHashing was too unstable for me to get a good read out.


Has anyone pushed their L3+ this high or higher before? I figure with the rapidly increasing difficulty and my 90 days about up I dont have much to lose. Would really love to hear what you guys think and have done!

Ive looked HW up a bunch and if its anything like GPU HW then it really shouldnt be an issue has their fixed internally. My first (and prob last) ASIC.

My ASIC is in my garage which is gets pretty cold at night - around 35-45 degrees F and durning the day I would guess maybe 60 but that is with fans running.

Your thoughts. Once this is all done I will make a video!

Sincerely
Rexmint

Tips appericated for my testing would be greatly appreciated...
BTC 1HWiP5ApidERRNie93SkMMiAEhJjUgc1oe
BTC SegWit 3F8uxJjV4yJVSosyPzFNyUzbeKNhtCezPb
ETH 0xa64345D423D5CEe8c8285c0F1C465860b177cA7A
LTC LVnTG8aGo3g3vk3xsFH2RdWu6G1Tjrn6vU
LTC SegWit (not sure if all LTC are Segwit but Ledger made me choice lol) MTurGTyMzVGE1iXGpADZiVNEdtVTTxa4B6