sounds like rail overload? try just 2 blades, not all 3!
Should really not be an issue.
Some cables i've had were weird and i had to mess around them with the multimeter before they worked. Not sure whats up with that.
Topic: Lepa G1600W PSU for Antminer S7 - Can't power it on ! Bounty 0.05 BTC - page 2. (Read 2311 times)
January 27, 2016, 01:30:41 PM
Should really not be an issue.
Some cables i've had were weird and i had to mess around them with the multimeter before they worked. Not sure whats up with that.
January 27, 2016, 01:29:36 PM
I would get a PSU tester from amazon, you can get it pretty cheap or you can go nicer with PCIE testers and LCD. That will allow you to measure current if it's working at all.
But if it truly is not powering on check and make sure paperclip is making contact with metal within it. Make sure you have on a right combination of 2 wires. And if that does not work you likely will need to email manufacture.
But if it truly is not powering on check and make sure paperclip is making contact with metal within it. Make sure you have on a right combination of 2 wires. And if that does not work you likely will need to email manufacture.
January 27, 2016, 01:09:09 PM
sounds like rail overload? try just 2 blades, not all 3!
January 27, 2016, 12:59:59 PM
it finally powered ON, when no cable was attached to the MINER
then I powered it off, I connected it to the miner and after a minute or too it powered off again
then I powered it off, I connected it to the miner and after a minute or too it powered off again
January 27, 2016, 12:48:08 PM
The PSU does not turn ON at all!
The S7 miner works just fine, I tested it with another PSU
The S7 miner works just fine, I tested it with another PSU
January 27, 2016, 12:40:30 PM
Does the PSU turn on at all? A bit unclear if both do not turn on or if only the miner does not turn on.
January 27, 2016, 12:38:49 PM
Looks like you need to make contact between the 2 round at the ''clip'' side of the mobo connector on the psu!
Do not connect to the last 2 as they are red!!!!(5volts?)
Do not connect to the last 2 as they are red!!!!(5volts?)
January 27, 2016, 12:31:40 PM
Sorry picture was unclear.... socket and plug seem right
January 27, 2016, 12:30:15 PM
The socket starts with rounded-square-square-rounded-rounded but from the pictures i see your plug doesn't?
January 27, 2016, 12:20:43 PM
Suna-ma! am una pusa pe un batch7
January 27, 2016, 12:13:06 PM
I have multiple Antminer S7, with multiple PSU's from corsair, EVGA, coolmaster, running 4 Antminer S7
Today my 5th Antminer S7 has arrived and I have also bought a 5th PSU for it
I got it brand new, connected all 10 PCI-e PINS to the S7, the MB cable, put the paperclip switch to it and tried to turn it on ... surprise, it won't work
Anyone has any experience with this PSU ? I have noticed the MB cable is a bit different than at my other PSU's
The MB cable is split in 2 in the part where it comes into the PSU, and 1 part has 12 small slots
here are the pictures of the MB cable :
I will give 0.05 BTC to whoever helps me solve the mistery !
Today my 5th Antminer S7 has arrived and I have also bought a 5th PSU for it
I got it brand new, connected all 10 PCI-e PINS to the S7, the MB cable, put the paperclip switch to it and tried to turn it on ... surprise, it won't work
Anyone has any experience with this PSU ? I have noticed the MB cable is a bit different than at my other PSU's
The MB cable is split in 2 in the part where it comes into the PSU, and 1 part has 12 small slots
here are the pictures of the MB cable :
I will give 0.05 BTC to whoever helps me solve the mistery !
Jump to: