Topic: M3A770DE with dual graphics.HELP! (Read 1854 times)
Any more suggestions?
On PCI PnP CONFIGURATION there is not a enable/disable or Yes/No
just has something like IDE Bus master wich is enabled...
and PCI latency timer...
OMG this really dont work..
just has something like IDE Bus master wich is enabled...
and PCI latency timer...
OMG this really dont work..
Maybe there is a PCI PnP CONFIGURATION, i will check it out tonight 
I didnt found plug and play or PnP. i think this board dont have.
Before you conclude your board is bad, check your bios settings and see if there is some kind of "plug and play" option that is disabled. If so, enable it, boot back into windows and see if this works. I had this issue with my board - my OS refused to display video on my secondary card until I enabled plug and play. May not work, but its worth a shot.
Im here to Help , so no Problem, and i tried my best. =)
Greetings, Frog
Greetings, Frog
Yeah i also think was board problem,
but thank u Frog,
there is no other person could help me instead you.
but thank u Frog,
there is no other person could help me instead you.
Well, then the Board is the Problem.
Maybe you should by a new one.
Because i cant say what on or in the Board causes the Error.
Greetings,
Frog
Maybe you should by a new one.
Because i cant say what on or in the Board causes the Error.
Greetings,
Frog
I tried two cards on x16 slot and both worked, so isnt card problem...
I also tried both cards on x4 and dont work..
PSU Corsair cx600 v2
I also tried both cards on x4 and dont work..
PSU Corsair cx600 v2
Try the Card which is running in the x16 Slot in the x4 please.
So far it seems like one of the Cards is the Problem.
Greetings,
Frog
So far it seems like one of the Cards is the Problem.
Greetings,
Frog
I tried just one card at X4 and no signal.
Maybe board problem?
Maybe board problem?
Heyho,
Remove the functioning Card from your Computer, then put the one that is not working into the Slot where the other Card was.
And start the Computer. If the Computer starts, and you have a Signal at the Screen, the Card is ok.
If not the Card seems to be Malfunctioning.
If you have a Signal, and the other Card to the x4 Slot. If you again have no Signal on the Second Card then,
maybe the PSU has not enough power(Watts) to maintain two Cards.
Greetings,
Frog
Remove the functioning Card from your Computer, then put the one that is not working into the Slot where the other Card was.
And start the Computer. If the Computer starts, and you have a Signal at the Screen, the Card is ok.
If not the Card seems to be Malfunctioning.
If you have a Signal, and the other Card to the x4 Slot. If you again have no Signal on the Second Card then,
maybe the PSU has not enough power(Watts) to maintain two Cards.
Greetings,
Frog
up! help please.
Hi,
I open a CCC and there dont have "Performance" and i dont find crossfire options.There havent a crossfire at CCC.
At Windows Resolution Settings, selected 2nd screen, and set to "Extend to this Screen"
and clicked apply nothing happen. The Extend to this Screen also changed to not marked,
so i dont know what to do, seems the motherboard dont recognise the second graphic.
:(someone help me please.
I open a CCC and there dont have "Performance" and i dont find crossfire options.There havent a crossfire at CCC.
At Windows Resolution Settings, selected 2nd screen, and set to "Extend to this Screen"
and clicked apply nothing happen. The Extend to this Screen also changed to not marked,
so i dont know what to do, seems the motherboard dont recognise the second graphic.
:(someone help me please.
Hi,
The Screen has to be Activated.
Go to Windows Resolution Settings, select 2nd screen, and set to "Extend to this Screen".
Then it should work.
Greetings
Frog
The Screen has to be Activated.
Go to Windows Resolution Settings, select 2nd screen, and set to "Extend to this Screen".
Then it should work.
Greetings
Frog
The problem is i connect a screen in each one and dont appears on guiminer and CCC..
Hey,
I had the Same issue.
Without Crossfire, i have to connect 1 Screen to every card. Then they show up in Miners, and at CCC.
When Crossfire is enabled, both cards show up, with just 1 Screen connected on the Primary Card.
You should have received the Cable with your Graphics Card.
If not, Crossfire should work without it too.
Greetings,
Frog
I had the Same issue.
Without Crossfire, i have to connect 1 Screen to every card. Then they show up in Miners, and at CCC.
When Crossfire is enabled, both cards show up, with just 1 Screen connected on the Primary Card.
You should have received the Cable with your Graphics Card.
If not, Crossfire should work without it too.
Greetings,
Frog
Hey Frog,
Yeah i installed the last version.
About Crossfire i think need something like crossfire bridge.
I dont have.
But i will try.without cable.
Gui miner shows two parameters like --platform=0 is a graphics card and --platform=0 its a CPU.
dont show the other card
I have heard to dont put crossfire will be better to mine.
thank u Frog.
Yeah i installed the last version.
About Crossfire i think need something like crossfire bridge.
I dont have.
But i will try.without cable.
Gui miner shows two parameters like --platform=0 is a graphics card and --platform=0 its a CPU.
dont show the other card
I have heard to dont put crossfire will be better to mine.
thank u Frog.
Okay,
Do you use the latest Catalyst ?
If not, download it, and install it.
If you do, follow these Steps:
1. Right click to Desktop, and select "AMD Vision Engine Control Center" formerly know as CCC=Catalyst Control Center
2. Go to "Performance" in the left Tab unter "Games"
3. Select "AMD CrossfireX Configuration
4. Check if the Tick at "Activate CrossfireX" is set. If it is, we have to think about again. If not, set it. And restart.
5. Now try to Mine (It will throw an Error)
6. To Fix this, you have to add a Parameter to the Miner Call Procedure.
Also note, that you have to start 2 Instances of the Miner to use 2 Cards for Mining.
The Parameter is --platform=0 or --platform=1 (try it, for me its 0)
One of those is the CPU, the other one is the Crossfire Bundle.
Please report back if this worked.
Greetings, Frog
Do you use the latest Catalyst ?
If not, download it, and install it.
If you do, follow these Steps:
1. Right click to Desktop, and select "AMD Vision Engine Control Center" formerly know as CCC=Catalyst Control Center
2. Go to "Performance" in the left Tab unter "Games"
3. Select "AMD CrossfireX Configuration
4. Check if the Tick at "Activate CrossfireX" is set. If it is, we have to think about again. If not, set it. And restart.
5. Now try to Mine (It will throw an Error)
6. To Fix this, you have to add a Parameter to the Miner Call Procedure.
Also note, that you have to start 2 Instances of the Miner to use 2 Cards for Mining.
The Parameter is --platform=0 or --platform=1 (try it, for me its 0)
One of those is the CPU, the other one is the Crossfire Bundle.
Please report back if this worked.
Greetings, Frog
Hi,
Question is, when does the Monitor dont show anything.
While booting ?
Or when in Windows ?
Fact is, only the Primary Card shows something when booting. (Which is the card in the Green Slot)
In Windows, you have to reinstall the Ati Driver to make the second card Working.
Dont forget to restart then. Back in Windows, you have to activate the Second screen manually, via
Windows resolution Settings.
On the other Hand, is the Bandwith of an x4 Slot very low compared to x16 which is standart,
i dont know if this is affecting the Mining Process, but its affecting 3D performance.
Hope i helped you a bit,
Frog
Question is, when does the Monitor dont show anything.
While booting ?
Or when in Windows ?
Fact is, only the Primary Card shows something when booting. (Which is the card in the Green Slot)
In Windows, you have to reinstall the Ati Driver to make the second card Working.
Dont forget to restart then. Back in Windows, you have to activate the Second screen manually, via
Windows resolution Settings.
On the other Hand, is the Bandwith of an x4 Slot very low compared to x16 which is standart,
i dont know if this is affecting the Mining Process, but its affecting 3D performance.
Hope i helped you a bit,
Frog
hey,
The monitor dont show anything while booting and in Windows, its like monitor is not connected to a graphic, its same monitor connected to power and no image.
I have unistalled Ati driver and installed again.
But still dont work, in Gui miner and Ati controler just show one graphic.
In windows device manager just show one card...
Also in Windows resolution Settings there say 2 monitors but i think when i just have one card also show 2.
Jump to: