As with the above post, yeah as usual, many people don't give a shit about the license requirements on cgminer, and want to support people like fubly who break licenses.
It's the standard open source GPLv3 license as stated in the code ... not difficult to adhere to at all.
Topic: MinToRRo Bitmain Antminer Firmware S5 / S7- The Flash one! (Read 15081 times)
Hello all!
As i can see, people had difficulties with this package... So i have my things to tell now.
This is working now pretty well with my 2x S7
Those are 54asic models and both are running with lowered mhz, volts, fans, temps and little down with gh/s
Fans are not loud, when under 3000 rpm. My miners temps with 3000 rpm are around 50c(+/-5c)
It was not easy for me neither to get FW work this well, but i had good support from Mintorro´s team!
My machines works without issues. Those temps are so low that i don´t need to touch fans never.(If fans 100% temps under 40c)
I burned it many times and after several sessions with support things started to work well.
-Be sure that your image is correct and if running from sd, verify that it´s not damaged card.
-https://ant´s ip/login.php opens when it´s ready
+ Sd-image saved my beaglebone!(Frankenstein mod) Other miner won´t boot without it.
+ Where are errors? 0.0x%
+/- Now i can hear my wife again.. So...
My watts dropped more than work! So back in business with S7´s
Roomtemp is about 20c and still they are quiet.
Thanks and good luck for others (if problems)!
Special thanks for Fubly! This is something and works as i need it
As i can see, people had difficulties with this package... So i have my things to tell now.
This is working now pretty well with my 2x S7
Those are 54asic models and both are running with lowered mhz, volts, fans, temps and little down with gh/s
Fans are not loud, when under 3000 rpm. My miners temps with 3000 rpm are around 50c(+/-5c)
It was not easy for me neither to get FW work this well, but i had good support from Mintorro´s team!
My machines works without issues. Those temps are so low that i don´t need to touch fans never.(If fans 100% temps under 40c)
I burned it many times and after several sessions with support things started to work well.
-Be sure that your image is correct and if running from sd, verify that it´s not damaged card.
-https://ant´s ip/login.php opens when it´s ready
+ Sd-image saved my beaglebone!(Frankenstein mod)
Other miner won´t boot without it.+ Where are errors? 0.0x%
+/- Now i can hear my wife again..
So... My watts dropped more than work! So back in business with S7´s
Roomtemp is about 20c and still they are quiet.
Thanks and good luck for others (if problems)!
Special thanks for Fubly! This is something and works as i need it
Where's the cgminer source code for every version, as is required by the cgminer license.
Dear Kano,
It is forked from yours! Since March 2016
https://github.com/Zwilla/cgminer
In that single pull request, among other things, I see commits with empty files ... like zapi.c zapi.h ...
Comments saying it doesn't work ...
A change to show passwords, and a lot of simply deleted code for FPGA and other drivers.
As I said,
Where's the cgminer source code for every version, as is required by the cgminer license?
Thumbs up Kano. I was just bumping in to this thread looking for an cgminer version 4.9.2 for the S7`s ....
How ever It does look like their is some very important improvements of the Bitmain Firmware that we all could benefit from. I think Fubly is on the right track with the Bitmain Firmware...
Where's the cgminer source code for every version, as is required by the cgminer license.
Dear Kano,
It is forked from yours! Since March 2016
https://github.com/Zwilla/cgminer
In that single pull request, among other things, I see commits with empty files ... like zapi.c zapi.h ...
Comments saying it doesn't work ...
A change to show passwords, and a lot of simply deleted code for FPGA and other drivers.
As I said,
Where's the cgminer source code for every version, as is required by the cgminer license?
hello fubly,
how do I get the free version of your firmware, i'd like to check it out..... i don't see it on your website...
can you put a link up please
how do I get the free version of your firmware, i'd like to check it out..... i don't see it on your website...
can you put a link up please
Where's the cgminer source code for every version, as is required by the cgminer license.
Dear Kano,
It is forked from yours! Since March 2016
https://github.com/Zwilla/cgminer
Where's the cgminer source code for every version, as is required by the cgminer license.
Hi together,
I have some features built in more.
For those which are running Version 0026 (check Menu -> Miner -> Firmware upgrade page)
_______________________________________________________________________________ _______________________________
How to update if you are running MinTorro > Version 0026
_______________________________________________________________________________ _______________________________
How to upgrade if you are running Old Firmware > Version 0026
_______________________________________________________________________________ _______________________________
NEW AntMiner S7 RECOVERY SD-IMAGE - It recovers every board!
How to setup SD-CARD Image?
Setup now your miner
Setup Intervals
thx
fubly
This picture said more than 1000 words
I have some features built in more.
- Cgminer 4.9.2. with full customize able fan speed (hard nut) from 1% to 100%. The combination of automatic temp control = Ready for halving. Share your results, please.
- Automatic restart or reboot (Tools -> Settings)
- new Overview
- Nicehash support 100% working (not jet tested by NiceHash) see here:Antminer S7 on 4.9.2 at nicehash.com
- on Firmware page (upgrade App) NO REBOOT NEEDED!!!
- Working two weeks on Bitmain driver again!!! With Overkill Mode you got the best results now!!!
- Hardware Errors now at a minimum
- Accepted Shares nearly 100% (99,992%) possible
For those which are running Version 0026 (check Menu -> Miner -> Firmware upgrade page)
_______________________________________________________________________________ _______________________________
How to update if you are running MinTorro > Version 0026
- download this file Mintorro-SetpOne.tar from your customer account
- Menu -> Miner -> Firmware upgrade
- click on run this action button
- If you don´t have this button goto old style - Upload Archive
- after second reboot the system is ready for halving and it will start mining with YOUR own Pools
_______________________________________________________________________________ _______________________________
How to upgrade if you are running Old Firmware > Version 0026
- download this file Mintorro-SetpOne.tar from your customer account
- Menu -> System -> Firmware upgrade
- On Menu: RESTORE CONFIG select this file
- click on upload
- after second reboot the system is ready for halving and it will start mining with YOUR own Pools
_______________________________________________________________________________ _______________________________
NEW AntMiner S7 RECOVERY SD-IMAGE - It recovers every board!
How to setup SD-CARD Image?
- Download this file from your account MinToRRo-SD-Live-and-Recovery-System-on-MicroSD-Card.img.7z
- on download page you will also find the password for it
- Burn it on micro sd-card
- switch off the Antminer S7
- power on and wait for 45 to 55 seconds
- now open you browser at for example https://192.168.178.17
- setup now your login with the datas from your account
- click on 'register now'
- and after this on 'login now'
Setup now your miner
- click on the menu -> Miner
- click on -> My local Miner
- activate NiceHash Mode
- fill out all other fields
- click on Make Overkill mode
- review now your settings
- click on Start Mining
- now you will be redirected to the overview Page
- reload the page if nothing happens after some seconds
Setup Intervals
- click on the menu 'Tools'
- click on my Settings
- best case "activate" now Rig Update Delay to 1 Minute
- and Pools to 10 minutes (depends on your pool provider)
thx
fubly
This picture said more than 1000 words
The only way to change the chip voltage is to re-program the PIC in the hash board with a PIC programmer.
See sidehack's thread https://bitcointalksearch.org/topic/m.15298837
See sidehack's thread https://bitcointalksearch.org/topic/m.15298837
Are you using regular cryptoglance? Or is three another one. Sorry if I'm missing something but I've read the thread and and noticed features that I don't recall on standard cryptoglance.
This is not the standard Cryptoglance (which I actually do use use for monitoring all my home miners). This is custom firmware plus a pretty awesome customization of Cryptoglance that is tied in with the custom firmware. The only bummer is that I want to undervolt the S7 Miner and this looks like one of the only options that does not seem to be functioning with this custom firmware or maybe its because the voltage is fixed for the S7. I am looking for a hardware solution for the undervolt now but I don't think anyone has done it except for the S1, S3 and maybe the S5 miners. With my utility rate, am now breaking even with the halving and the current difficulty.
Are you using regular cryptoglance? Or is three another one. Sorry if I'm missing something but I've read the thread and and noticed features that I don't recall on standard cryptoglance.
Fubly,
I noticed in your demo video you used the configuration option: 'Zwilla Mod Special Miner Options ALL: 115200:32:8:7:200:0782:0725'. What are these parameters for specifically and should I be using them for undervolting?
-Ondart
Fubly,
I performed a more in-depth undervolt testing today. I think this pretty much confirms that the undervolt settings for my S7 AntMiner running cgminer 4.8.1 are not affecting the miner or reducing power consumption at the wall. I think this firmware is fantastic and has many valuable features. However, the one feature that is most important to me and I believe for many others is to extend the life of the S7 miner after the halving and as the difficulty increases by reducing utility costs. The amperage consumed by the S7 Miner does not noticeably change when undervolted even all the way down to the 0600 undervolt setting. Is there any other configuration that can be made to get the Miner to recognize voltage changes with this firmware?
Here are the results of my testing. I kept the frequency at the default 625 for the S7-B7 miner and stepped down the voltage using every setting and pulled the statistics at the 5 minute mark.
Test 1
| Hash Rate (5 Min/Avg) 4,960 Freq 625.00 Voltage .0706 (Default) Temps 73/73/73 AMPS 12.66 FAN RPM 3600/3600 |
| Hash Rate (5 Min/Avg) 4,980 Freq 625.00 Voltage .0696 Temps 73/72/73 AMPS 12.50 FAN RPM 3600/3600 |
| Hash Rate (5 Min/Avg) 4,930 Freq 625.00 Voltage .0684 Temps 73/72/73 AMPS 12.53 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 4,864 Freq 625.00 Voltage .0672 Temps 73/72/74 AMPS 12.57 FAN RPM 3600/3600 |
| Hash Rate (5 Min/Avg) 4,762 Freq 625.00 Voltage .0660 Temps 73/72/73 AMPS 12.66 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 5059 Freq 625.00 Voltage .0648 Temps 73/72/74 AMPS 12.60 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 4731 Freq 625.00 Voltage .0636 Temps 73/73/74 AMPS 12.61 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 4,908 Freq 625.00 Voltage .0624 Temps 74/73/74 AMPS 12.60 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 4,881 Freq 625.00 Voltage .0625 Temps 73/73/74 AMPS 12.60 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 5,132 Freq 625.00 Voltage .0612 Temps 73/73/74 AMPS 12.60 FAN RPM 3720/3600 |
| Hash Rate (5 Min/Avg) 4,999 Freq 625.00 Voltage .0600 Temps 73/73/74 AMPS 12.55 FAN RPM 3600/3600 |
Fubly,
I have done a couple of simple AntMiner S7 / Mintorro Firmware undervolt tests and the results were not what I expected. My test was to baseline at safe lower Frequency (500M) and use the stock ASIC Voltage (.706) and document the AMPs consumed at the wall. Then perform two tests by lowering the voltage only and observe the AMPs consumed and any temperature differences. I expected to see significantly less AMPs at the wall when dropping the voltage to the ASIC chips. Dropping the voltage had very little or no difference in Amperage consumption at the wall unexpectedly.
On a side note, I noticed that when I made the Frequency and Voltage changes on the 'my local Miner' page and saved it by clicking 'Check your Configuration Here', the cgminer.conf configuration file content did not show the changes. I had to manually change the frequency and voltage, save cgminer.conf and then 'Kill Mining Software' and then 'Start Mining Software' for the changes to take effect.
I could use some advice if there is a better way to do this test or any other recommendations.
The test results are as follows:
Undervolt Test Baseline
Miner: AntMiner S7 Batch 7
ASIC: BM1385
Custom Frequency: 500M
Stock ASIC Voltage: 0.706v
Actual Power Consumption at the Wall: 9.880A
Comments: This is the baseline test
Undervolt Test 1
Miner: AntMiner S7 Batch 7
ASIC: BM1385
Modified Frequency: 500M
Modified ASIC Voltage: 0.672v
Actual Power Consumption at the Wall: 9.67A
Comments: The Amperage dropped very little, .21A from the baseline
Undervolt Test 2
Miner: AntMiner S7 Batch 7
ASIC: BM1385
Modified Frequency: 500M
Modified ASIC Voltage: 0.636v
Actual Power Consumption at the Wall: 9.67A
Comments: The Amperage did not change, still .21A from the baseline
I have done a couple of simple AntMiner S7 / Mintorro Firmware undervolt tests and the results were not what I expected. My test was to baseline at safe lower Frequency (500M) and use the stock ASIC Voltage (.706) and document the AMPs consumed at the wall. Then perform two tests by lowering the voltage only and observe the AMPs consumed and any temperature differences. I expected to see significantly less AMPs at the wall when dropping the voltage to the ASIC chips. Dropping the voltage had very little or no difference in Amperage consumption at the wall unexpectedly.
On a side note, I noticed that when I made the Frequency and Voltage changes on the 'my local Miner' page and saved it by clicking 'Check your Configuration Here', the cgminer.conf configuration file content did not show the changes. I had to manually change the frequency and voltage, save cgminer.conf and then 'Kill Mining Software' and then 'Start Mining Software' for the changes to take effect.
I could use some advice if there is a better way to do this test or any other recommendations.
The test results are as follows:
Undervolt Test Baseline
Miner: AntMiner S7 Batch 7
ASIC: BM1385
Custom Frequency: 500M
Stock ASIC Voltage: 0.706v
Actual Power Consumption at the Wall: 9.880A
Comments: This is the baseline test
Undervolt Test 1
Miner: AntMiner S7 Batch 7
ASIC: BM1385
Modified Frequency: 500M
Modified ASIC Voltage: 0.672v
Actual Power Consumption at the Wall: 9.67A
Comments: The Amperage dropped very little, .21A from the baseline
Undervolt Test 2
Miner: AntMiner S7 Batch 7
ASIC: BM1385
Modified Frequency: 500M
Modified ASIC Voltage: 0.636v
Actual Power Consumption at the Wall: 9.67A
Comments: The Amperage did not change, still .21A from the baseline
Dear Customer,
here are the answers for your questions.
1. My main issue now is the Old-Miner page shows version 4.8.1 and it should be 4.8.2. I need your help to fix this.
-> If you click on "Make Overkill Mod" and restart the mining software (No reboot is needed)
This worked.
2. I can't seem to bring down the fans. I set them to 50% and they are still running at full speed. Do I need to reboot the Miner to set it?
-> please use UpdateApp.tar to fix that - > No reboot is needed ! -> Problem: On Cgminer.config direct you find a value "bitmain-temp", just delete this one!
Or after update just klick on "Make 480 Mod" and the line disappears.
This worked also and set it back to v4.8.1 but now I have dynamic fan control which is really what I wanted.
3. Is it possible to configure the fans to auto regulate speed per desired temperature? I have tried both Fan Auto Modus on and off with no change seen.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
I set the fan range to 40% min and 55% max. My miner fans are both running around 3,600 RPM now and the temp is around 71 degrees where I set it. I see the fans change RPM when needed so this is exactly what I wanted.
4. How do I view the temp control app? I click the button but I can't see how to get to the temp control app page.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
5. Is the license transferable if I sell the miner?
-> Yes - just let me know who will get the copy now and this / your customer has to open and register an account on our website Zwilla.de. After we knew
who will use your copy now we transfer it to him. On your side you have to click on the login page through the button "unregister this miner now!"
6. Does the license need to be renewed yearly or is it good for the lifetime of the Miner?
It is good for lifetime!
7. How are the SSL certs renewed when they expire?
The SSL cert is generated directly on your miner during Stepone Upgrade and it is 10 years valid.
fubly
here are the answers for your questions.
1. My main issue now is the Old-Miner page shows version 4.8.1 and it should be 4.8.2. I need your help to fix this.
-> If you click on "Make Overkill Mod" and restart the mining software (No reboot is needed)
This worked.
2. I can't seem to bring down the fans. I set them to 50% and they are still running at full speed. Do I need to reboot the Miner to set it?
-> please use UpdateApp.tar to fix that - > No reboot is needed ! -> Problem: On Cgminer.config direct you find a value "bitmain-temp", just delete this one!
Or after update just klick on "Make 480 Mod" and the line disappears.
This worked also and set it back to v4.8.1 but now I have dynamic fan control which is really what I wanted.
3. Is it possible to configure the fans to auto regulate speed per desired temperature? I have tried both Fan Auto Modus on and off with no change seen.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
I set the fan range to 40% min and 55% max. My miner fans are both running around 3,600 RPM now and the temp is around 71 degrees where I set it. I see the fans change RPM when needed so this is exactly what I wanted.
4. How do I view the temp control app? I click the button but I can't see how to get to the temp control app page.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
5. Is the license transferable if I sell the miner?
-> Yes - just let me know who will get the copy now and this / your customer has to open and register an account on our website Zwilla.de. After we knew
who will use your copy now we transfer it to him. On your side you have to click on the login page through the button "unregister this miner now!"
6. Does the license need to be renewed yearly or is it good for the lifetime of the Miner?
It is good for lifetime!
7. How are the SSL certs renewed when they expire?
The SSL cert is generated directly on your miner during Stepone Upgrade and it is 10 years valid.
fubly
Question: On the AntMiner Stats Summary Page, there is a field that says 'RIDE ON' and there is a link that says 'CHECK'. Clicking the link takes me to the miner configuration page. What does this mean?
I will be undervoltage testing later day and will post my results. I am pretty happy so far Fubly.
-Ondart
Customers Question:
Any news about S5 Miners?
Answer:
If you use StepOne upgrade it will work out of the box. I have no S5 for testing but other customers where reporting it to me.
If it will not work well we / you can adjust the settings on the menu:
-> Dashboard -> Miner -> My local miner
or here
-> Dashboard -> Miner -> Cgminer.conf direct
After you made your changes, please click on "Start Mining Software" button.
At the fist time you setup your miner with MinToRRo for S5 please,
let MinerType on S7 fill all fields with your settings and click than on any "Make xxxx Mod button"
Now you can switch to AntminerType "S5" select your MHZ and click on "Make 480 Mod" button.
Then restart mining software by click on "Start Mining Software", please.
fubly
Any news about S5 Miners?
Answer:
If you use StepOne upgrade it will work out of the box. I have no S5 for testing but other customers where reporting it to me.
If it will not work well we / you can adjust the settings on the menu:
-> Dashboard -> Miner -> My local miner
or here
-> Dashboard -> Miner -> Cgminer.conf direct
After you made your changes, please click on "Start Mining Software" button.
At the fist time you setup your miner with MinToRRo for S5 please,
let MinerType on S7 fill all fields with your settings and click than on any "Make xxxx Mod button"
Now you can switch to AntminerType "S5" select your MHZ and click on "Make 480 Mod" button.
Then restart mining software by click on "Start Mining Software", please.
fubly
Dear Customer,
here are the answers for your questions.
1. My main issue now is the Old-Miner page shows version 4.8.1 and it should be 4.8.2. I need your help to fix this.
-> If you click on "Make Overkill Mod" and restart the mining software (No reboot is needed)
2. I can't seem to bring down the fans. I set them to 50% and they are still running at full speed. Do I need to reboot the Miner to set it?
-> please use UpdateApp.tar to fix that - > No reboot is needed ! -> Problem: On Cgminer.config direct you find a value "bitmain-temp", just delete this one!
Or after update just klick on "Make 480 Mod" and the line disappears.
3. Is it possible to configure the fans to auto regulate speed per desired temperature? I have tried both Fan Auto Modus on and off with no change seen.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
4. How do I view the temp control app? I click the button but I can't see how to get to the temp control app page.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
5. Is the license transferable if I sell the miner?
-> Yes - just let me know who will get the copy now and this / your customer has to open and register an account on our website Zwilla.de. After we knew
who will use your copy now we transfer it to him. On your side you have to click on the login page through the button "unregister this miner now!"
6. Does the license need to be renewed yearly or is it good for the lifetime of the Miner?
It is good for lifetime!
7. How are the SSL certs renewed when they expire?
The SSL cert is generated directly on your miner during Stepone Upgrade and it is 10 years valid.
fubly
here are the answers for your questions.
1. My main issue now is the Old-Miner page shows version 4.8.1 and it should be 4.8.2. I need your help to fix this.
-> If you click on "Make Overkill Mod" and restart the mining software (No reboot is needed)
2. I can't seem to bring down the fans. I set them to 50% and they are still running at full speed. Do I need to reboot the Miner to set it?
-> please use UpdateApp.tar to fix that - > No reboot is needed ! -> Problem: On Cgminer.config direct you find a value "bitmain-temp", just delete this one!
Or after update just klick on "Make 480 Mod" and the line disappears.
3. Is it possible to configure the fans to auto regulate speed per desired temperature? I have tried both Fan Auto Modus on and off with no change seen.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
4. How do I view the temp control app? I click the button but I can't see how to get to the temp control app page.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
5. Is the license transferable if I sell the miner?
-> Yes - just let me know who will get the copy now and this / your customer has to open and register an account on our website Zwilla.de. After we knew
who will use your copy now we transfer it to him. On your side you have to click on the login page through the button "unregister this miner now!"
6. Does the license need to be renewed yearly or is it good for the lifetime of the Miner?
It is good for lifetime!
7. How are the SSL certs renewed when they expire?
The SSL cert is generated directly on your miner during Stepone Upgrade and it is 10 years valid.
fubly
Fubly,
Thank you for the personal e-mail and additional instructions to assist me. All my problems are resolved now except for one last issue. When I check the Old-Menu page, the version still shows 4.8.1. I e-mailed you with details so you could help me out tomorrow and thank you for the excellent support. This custom firmware is what I have been looking for and its totally awesome. Once I get the miner running on 4.8.2 with your help tomorrow I will then be testing bringing down voltage and hash rate and observing lower AMPs at the wall which is expected to lower my electricity costs running the miner. If this works as I expect it will, I am going to be able to run my S7s well into the halving and as the difficulty increases and continue to make a profit over utility costs. Once I do this testing, I will be purchasing more licenses for my other S7s. I will send more details as soon as I get them tomorrow.
-Ondart
Thank you for the personal e-mail and additional instructions to assist me. All my problems are resolved now except for one last issue. When I check the Old-Menu page, the version still shows 4.8.1. I e-mailed you with details so you could help me out tomorrow and thank you for the excellent support. This custom firmware is what I have been looking for and its totally awesome. Once I get the miner running on 4.8.2 with your help tomorrow I will then be testing bringing down voltage and hash rate and observing lower AMPs at the wall which is expected to lower my electricity costs running the miner. If this works as I expect it will, I am going to be able to run my S7s well into the halving and as the difficulty increases and continue to make a profit over utility costs. Once I do this testing, I will be purchasing more licenses for my other S7s. I will send more details as soon as I get them tomorrow.
-Ondart
I am at the point now where I am attempting to activate the license key so I can change to Red Z-Mod 492. Every time I login it asks me to register. When I attempt to register it says 'NO ist falsch' so something is not right. I see the following errors on the screen. The text says I have a valid license. I can't seem to find a way around this issue at the moment. The good thing is that while I figure this out, my rig is still mining with my normal settings so I am not losing anything. I wanted to note that the support provided by Michael on the support e-mail has been responsive and appreciated even with the time difference from the US.
Here are the errors I see when attempting to register my license:
Warning: unlink(/config/user_data/configs/license-active.json): No such file or directory in /www/miner-settings.php on line 212
Dear Ondart,
This appears only on the SD-Card Recovery Image, because there is no login possible. Please use the SD-Image only for recovering.
thx fubly
p.s my personal 36 hours uptime period is now finished. I'm knocked out today. (I will respond to the next messages within 18 hours n8)
I ended up booting to the SD Card and then flashing the latest Bitmain S7 Batch 7 firmware. Once I did this I was able to boot up without the Recovery SD card zwilla mod. I then re-executed the Mintorro-Setpone.tar Ugrade and it was successful this time. I was able to get into the interface and determine that it was hashing with my default values. I then successfully executed the Update procedure. My lesson learned here was to flash to the latest default firmware before executing the Update procedure. I think a comment about this should be at the beginning of the Update instructions. I am trying to configure the miner and get into 'Z-Mod 492' Red mode next. I'll post more info soon. So far so good...
Dear Ondart and to all other customers!
Please! Before you upgrade or update download a new copy of StepOne and others, because I update these scripts every day and that multiple times a day.
To StepOne:
StepOne contains all functions to update, upgrade your miner there is no need to use the upgrade after using StepOne, because StepOne will do it all for you.
So when you where using StepOne the onliest think you can run it UpdateApp.tar.
UpdateApp.tar will catch the brand new Version of MinToRRo (into background) installs all and that without stop mining and without any reboot.
fubly
Hello Fubly,
I need assistance. I executed your 'Upgrade' procedure and did a System Upgrade, Restore Backup of Mintorro-SetpOne.tar on my AntMiner S7 Batch 2. I waited over 10 min and the miner never recovered and never came back up on the network. The network status light flashes red continuously. I am attempting to recover using your 'Recovery' procedure. I flashed the SD card successfully, installed it in the Miner and booted up on the SD card without an issue so I am back up and mining for now but I need some help here.
Recovery Question: I can now only run the miner on the SD card as it will not bootup with network connectivity without it. Should I flash the original Firmware and then restore my original backup to get this miner able to boot up on stock firmware and without the SD card?
Upgrade Question: I really want to see this firmware function. How do I determine what went wrong and how do I get this firmware functional? Do I need to be at a particular stock Bitmain firmware level running first for the upgrade to be successful?
Hi Ondart,
I was writing you a detailed email atm, please check your inbox and let me know if it now working!
Please take a look to the How To, then will you discover that the SD-Card is only for recovering a none working Antminer. It will recover every absolute death flashed Antminer S5 and S7.
fubly
I am at the point now where I am attempting to activate the license key so I can change to Red Z-Mod 492. Every time I login it asks me to register. When I attempt to register it says 'NO ist falsch' so something is not right. I see the following errors on the screen. The text says I have a valid license. I can't seem to find a way around this issue at the moment. The good thing is that while I figure this out, my rig is still mining with my normal settings so I am not losing anything. I wanted to note that the support provided by Michael on the support e-mail has been responsive and appreciated even with the time difference from the US.
Here are the errors I see when attempting to register my license:
Warning: unlink(/config/user_data/configs/license-active.json): No such file or directory in /www/miner-settings.php on line 212
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
Warning: Cannot modify header information - headers already sent by (output started at /www/includes/headar.php:3) in /www/miner-settings.php on line 277
I ended up booting to the SD Card and then flashing the latest Bitmain S7 Batch 7 firmware. Once I did this I was able to boot up without the Recovery SD card zwilla mod. I then re-executed the Mintorro-Setpone.tar Ugrade and it was successful this time. I was able to get into the interface and determine that it was hashing with my default values. I then successfully executed the Update procedure. My lesson learned here was to flash to the latest default firmware before executing the Update procedure. I think a comment about this should be at the beginning of the Update instructions. I am trying to configure the miner and get into 'Z-Mod 492' Red mode next. I'll post more info soon. So far so good...
Hello Fubly,
I need assistance. I executed your 'Upgrade' procedure and did a System Upgrade, Restore Backup of Mintorro-SetpOne.tar on my AntMiner S7 Batch 2. I waited over 10 min and the miner never recovered and never came back up on the network. The network status light flashes red continuously. I am attempting to recover using your 'Recovery' procedure. I flashed the SD card successfully, installed it in the Miner and booted up on the SD card without an issue so I am back up and mining for now but I need some help here.
Recovery Question: I can now only run the miner on the SD card as it will not bootup with network connectivity without it. Should I flash the original Firmware and then restore my original backup to get this miner able to boot up on stock firmware and without the SD card?
Upgrade Question: I really want to see this firmware function. How do I determine what went wrong and how do I get this firmware functional? Do I need to be at a particular stock Bitmain firmware level running first for the upgrade to be successful?
you can find the source codes here:
http://www.mintorro.com/help.php
Kano, what problem do you have? Do you also give away a work of many month for free?
What else do you want to stay in your thread?
I do not know what else you want from me. What is the point of your actions?
Let me explain:
All time spending on this project, about 1800 hours.
And now, you have really nothing better to do than talking, writing and acting from one post to the other against me.
If you write a song it will not be "open source", a single musical note is "open source".
You better ask bitmain where the "source" of bmminer is. It is a fork of your 4.9.2 and nothing else.
Also you can ask them where the "REAL" source of cgminer 4.8.0 for Antminer S7 is or where the REAL source of the S5 cgminer is.
That what they where posting on github is an absolut fake!
If you also life from nothing, decrease the fee of your pool, please, and let me sell my composition.
And now let me explain in german what I wrote, and after this you can explain where there the problem is:
https://bitcointalksearch.org/topic/m.14698985
other user inclusive you mean that I have no plan how hashing works. Then I wrote:
Means:
By studying the driver from bitmain (more then 2 month, every day)
Means:
Means:
Finish! And you mean that's all a big lie? Make up your own mind,please.
And I done more then optimizing the timeout, I also reserved 10 x more ram for cgminer and limited the cpu to 94%.
Before you or every other mean that this is also bs, than please just open your miner with ssh, then screen -r and press d and d again. For that you will enter the debug mode, now you can verify that your miner only hashes the half more or minus. This is the evidence that if the cgminer has not enough ram and cpu power the hashrate goes down.
thx fubly
Edit: Update:
http://www.mintorro.com/help.php
Kano, what problem do you have? Do you also give away a work of many month for free?
What else do you want to stay in your thread?
I do not know what else you want from me. What is the point of your actions?
Let me explain:
- Working 12 to 16 hours a day on this firmware sine December 2015 also on most Sun and Saturday's
- to get out more features of this machine.
- Compiling so many tools (see the link above) to get it work
- I spend weeks to figure out how this guys from Bitmain, start boot, and hide code from our eyes.
- More then a month to get cgminer 492 working
- and also the Nicehash support
- my mistake by acting with the cryptoglance software (more than a month)
- many many days without any sleep
- form March to May many times 36 hour working - 8 hours sleep for 3-4 periods, then knock out for 12 hours
All time spending on this project, about 1800 hours.
And now, you have really nothing better to do than talking, writing and acting from one post to the other against me.
If you write a song it will not be "open source", a single musical note is "open source".
You better ask bitmain where the "source" of bmminer is. It is a fork of your 4.9.2 and nothing else.
Also you can ask them where the "REAL" source of cgminer 4.8.0 for Antminer S7 is or where the REAL source of the S5 cgminer is.
That what they where posting on github is an absolut fake!
If you also life from nothing, decrease the fee of your pool, please, and let me sell my composition.
And now let me explain in german what I wrote, and after this you can explain where there the problem is:
https://bitcointalksearch.org/topic/m.14698985
Quote
I was writing that with MinToRRo it is possible to get better results out of every hash work
other user inclusive you mean that I have no plan how hashing works. Then I wrote:
Quote
Stimmt, Ahnung habe ich definitiv keine!!!
Means:
Quote
YES, I have absolut no idea how it works!!!
andQuote
Jedoch, wenn ich einem Core, die Möglichkeit gebe eine Operation auszuführen = Hash-Auftag
bekommt dieser eine Möglichkeit diese Aufgabe auszuführen innerhalb einer bestimmten Zeit.
bekommt dieser eine Möglichkeit diese Aufgabe auszuführen innerhalb einer bestimmten Zeit.
By studying the driver from bitmain (more then 2 month, every day)
Means:
Quote
But, if I give a single core more time, before I get an error (timeout),
what mean that the input work on this core was for the ass.
OK?! Understand: -> TimeOut = Work for the A = on most cases Hardware Error = Bitmain definition.
And now?
I'am a liar? No !!! or YES Make up your own mind.
But I say, think and believe that: AS lower the hardware error AS lower the work for the A AS higher the chance to find better shares AND AS lower the Hardware Errors AS higher the hashrate
what mean that the input work on this core was for the ass.
OK?! Understand: -> TimeOut = Work for the A = on most cases Hardware Error = Bitmain definition.
And now?
I'am a liar? No !!! or YES Make up your own mind.But I say, think and believe that: AS lower the hardware error AS lower the work for the A AS higher the chance to find better shares AND AS lower the Hardware Errors AS higher the hashrate
Quote
So ist es aktuell in der original Software hinterlegt, wenn ich jetzt aber hingehe und diese Zeit nur leicht anhebe, dann erhöht das auch
die Wahrscheinlichkeit.
die Wahrscheinlichkeit.
Means:
Quote
At moment it is on original software recorded, but if I decrease now the timeout a little bit, then I decrease also the chance
Finish! And you mean that's all a big lie? Make up your own mind,please.
And I done more then optimizing the timeout, I also reserved 10 x more ram for cgminer and limited the cpu to 94%.
Before you or every other mean that this is also bs, than please just open your miner with ssh, then screen -r and press d and d again. For that you will enter the debug mode, now you can verify that your miner only hashes the half more or minus. This is the evidence that if the cgminer has not enough ram and cpu power the hashrate goes down.
Quote
press "CTRL" and on "A" and then on "D" to leave the screen session
thx fubly
Edit: Update:
Update: I have added an automatic https http redirect now on mintorro.
For updating please use only the "Mintorro-Update.tar" this will update only the running system. Within the half time of StepOne File!
Oh I forgot, I have opened all port on the boards (9), can any one confirm if they work. On my bixes it doesn´t work, but I'm 100% sure that I added the code as it have to.
For updating please use only the "Mintorro-Update.tar" this will update only the running system. Within the half time of StepOne File!
Oh I forgot, I have opened all port on the boards (9), can any one confirm if they work. On my bixes it doesn´t work, but I'm 100% sure that I added the code as it have to.
Good news i like it but it was a bear to get loaded in right for me i had to make sure my S5 had the July Firmware not the one i had in it . once i had it set to that firmware it all loaded in great took a few mins to adjust but now i can do a lot more with what i have for now once i get a S7 or two il buy two more copy's and the s5 is going solo .
ty
and
hope my feed back helped remember this is what i had to do to get it to work , now to play with it see what freedom it gives me.
cya
PS trying to download the SD image still says Sorry, you have reached the download limit for this file. not the tar file i can download the tar file and it still loads any firmware version i try to S7 and the only way it lets me adjust the fan speed is if i use the old classic way and it only hashes at 4.56 GH no TH very slow because of the firmware it keeps trying to load the S7 and S5 use completely different firmware but the S5 + will work on the S5 if you have so many blades loaded using it. sigh for now because of the annoying high 100 % fan speed it going back to the default S5 i was using from nice hash .I'll study it more and watch some of the wordless videos with no writing that explains nothing, so its hit and miss guessing .but i do like it but it's not working as intended and should not be such a pain to get just right .
last question was this even tested on a S5 it looks like no it wasn't ?. I'm willing to bet it will load a S7 or S9 flawless .
cya
ty
and
hope my feed back helped remember this is what i had to do to get it to work , now to play with it see what freedom it gives me.
cya
PS trying to download the SD image still says Sorry, you have reached the download limit for this file. not the tar file i can download the tar file and it still loads any firmware version i try to S7 and the only way it lets me adjust the fan speed is if i use the old classic way and it only hashes at 4.56 GH no TH very slow because of the firmware it keeps trying to load the S7 and S5 use completely different firmware but the S5 + will work on the S5 if you have so many blades loaded using it. sigh for now because of the annoying high 100 % fan speed it going back to the default S5 i was using from nice hash .I'll study it more and watch some of the wordless videos with no writing that explains nothing, so its hit and miss guessing .but i do like it but it's not working as intended and should not be such a pain to get just right .
last question was this even tested on a S5 it looks like no it wasn't ?. I'm willing to bet it will load a S7 or S9 flawless .
cya
i got into it I put port 80 like this at end if you can't access it.
make sure it is not .
read father i was able to find the flash not the SD image which is what had a limit on it after i was able to read your site better .
I can only access it with the SD image loaded on the miner i did make a mistake of not backing up my old s5 setting so now the only way i get into it is if i have the sd card in the s5 . the Mintorro-SetpOne.tar
image was loaded in how you said etc so no idea wtf went wrong. I'll fix that and burn a s4 image t0 SD and load it as a S4 then put it back to default s5 because I tried to load the default image with your image for recovering it gives me a dead page and doesn't work and I tried other things probably everything you ask me to.
and the fan from what i was able to figure stays at 100 no matter what mode it is till I adjust it , it loads the s7 firmware o my s5 so now im gonna get the s5 july firmware after i get it back to default were i can do something,then try sense there was a issue using other version of cgminer then the one from that firm ware the fan spins at a 100 % if you load in any other miners software then what it came with. I'm not being a jerk if it seems I am this is feedback to me there is no other way to put it but seem to be rude im not . if i had a S7 the way it looks it will load out of the box as intended but i don't but will soon sense the S9 are out and above what i can afford .s7 should be come S5 prices and S5 should be come S3 prices if there not all ready i haven't gone shopping yet.
and this can also mean the BB files got corrupted so it won't load any pages thu the browser but will if i use SSH which i can do that way but is not to help full unless i do a lot of replacing so ill S4 it then load the July bitmain firmware and let you know.
recovering now
Warning: session_start(): Cannot send session cookie - headers already sent by (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: session_start(): Cannot send session cache limiter - headers already sent (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: Cannot modify header information - headers already sent by (output started at /www/index.php:23) in /www/index.php on line 32
so using this does work https://bitmaintech.com/support.htm?pid=007201604120945219855QObfk20066C then i loaded it to the S5 July firmware it looks like you all use . im back to default S5 now gonna reload the Mintorro-SetpOne.tar and see what that does with the S5 July firmware not the May version i had loaded .
Code:
https://your Ip:80
Code:
https
Code:
http
read father i was able to find the flash not the SD image which is what had a limit on it after i was able to read your site better
.I can only access it with the SD image loaded on the miner i did make a mistake of not backing up my old s5 setting so now the only way i get into it is if i have the sd card in the s5 . the Mintorro-SetpOne.tar
image was loaded in how you said etc so no idea wtf went wrong. I'll fix that and burn a s4 image t0 SD and load it as a S4 then put it back to default s5 because I tried to load the default image with your image for recovering it gives me a dead page and doesn't work and I tried other things probably everything you ask me to.
and the fan from what i was able to figure stays at 100 no matter what mode it is till I adjust it , it loads the s7 firmware o my s5 so now im gonna get the s5 july firmware after i get it back to default were i can do something,then try sense there was a issue using other version of cgminer then the one from that firm ware the fan spins at a 100 % if you load in any other miners software then what it came with. I'm not being a jerk if it seems I am this is feedback to me there is no other way to put it but seem to be rude im not . if i had a S7 the way it looks it will load out of the box as intended but i don't but will soon sense the S9 are out and above what i can afford .s7 should be come S5 prices and S5 should be come S3 prices if there not all ready i haven't gone shopping yet.
and this can also mean the BB files got corrupted so it won't load any pages thu the browser but will if i use SSH which i can do that way but is not to help full unless i do a lot of replacing so ill S4 it then load the July bitmain firmware and let you know.
recovering now
Warning: session_start(): Cannot send session cookie - headers already sent by (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: session_start(): Cannot send session cache limiter - headers already sent (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: Cannot modify header information - headers already sent by (output started at /www/index.php:23) in /www/index.php on line 32
so using this does work https://bitmaintech.com/support.htm?pid=007201604120945219855QObfk20066C then i loaded it to the S5 July firmware it looks like you all use . im back to default S5 now gonna reload the Mintorro-SetpOne.tar and see what that does with the S5 July firmware not the May version i had loaded .
well to start with i can't down load any thing it keeps saying this to me
Sorry, you have reached the download limit for this file.
if there is no limits on down loads why i do keep getting the above .
your site is so hard to understand because the translator you all use when i use it, does not work to well. i end up using google translator which actually works better then one you all use or seems to if you use the same one it''s not set up right or something .
Sorry, you have reached the download limit for this file.
if there is no limits on down loads why i do keep getting the above .
your site is so hard to understand because the translator you all use when i use it, does not work to well. i end up using google translator which actually works better then one you all use or seems to if you use the same one it''s not set up right or something .
Download limit now fixed!
I hope you don't think i have to pay another 20 bucks for software that never worked right to start with . beyond that let me know . Please !!! .
last thought clicking this : http://www.mintorro.com goes to a dead page or i get this:
Forbidden
You don't have permission to access / on this server.
Apache/2.4.20 (Ubuntu) Server at www.mintorro.com Port 80
last thought clicking this : http://www.mintorro.com goes to a dead page or i get this:
Forbidden
You don't have permission to access / on this server.
Apache/2.4.20 (Ubuntu) Server at www.mintorro.com Port 80
The page is empty, thats right! And no other 20 bucks!
i was able to read the site enough to get flash but now after i do it how you said here i get this
recovering now
Warning: session_start(): Cannot send session cookie - headers already sent by (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: session_start(): Cannot send session cache limiter - headers already sent (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: Cannot modify header information - headers already sent by (output started at /www/index.php:23) in /www/index.php on line 32
How could you flash your minern, when the download limit is reached?
/www/index.php:23 -> just looks for your /config/cgminer/cgminer-s7.conf (this is nearly impossible, that this file is not existing. If is only called s7.conf, but it is used for all miners S5 and S7)
I was upgrading more then 40 miners, without any problems like that.
Warning: session_start(): It is a php problem, on the first start.
At this case:
1. The software tries to read the settings-file but it takes some seconds to create it.
2. You are using the copy for more then one miner, if so, click on the button "unregister miner" on that you want uninstall MinToRRo.
Just put in your credentials again.
Your login = the email Address from customer account
Pass: = what you want
Did MinToRRO recovering your settings?
Was the miner running after update on your own and private cgminer.conf ?
Honestly i don't see how this is much better then before the fan still spins at a 100 % all the time but now i can't even access anything on my S5 to lower the fan speed and will have to do a hard ware reset and hope that works if it doesn't then the SD way , if that does i do have a BB laying around as backup , i hope i just didn't thrash the BB on the miner now .
On which mode do you run the firmware?
on "Overkill mode" it runs on 100% Fan Speed, there is no open source code for the driver. There is one, but not that with the vil mode from Bitmain!
also i don't use the July firmware from bitmain it sucks worse then the ones before it i do use the may 2015 version forked from nicehash sense it works better then any version bitmain put out and not the July 15 2015 version you all may have , i see i may have to update to for this to work right ?
I really want to use this software but at this point in time it's shit and i can't say i have anything good to say about it , till it really works like it should out of the box GL .. I normally don't have issue picking some thing up.
I sent another email !!! .
cya
I really want to use this software but at this point in time it's shit and i can't say i have anything good to say about it , till it really works like it should out of the box GL .. I normally don't have issue picking some thing up.
I sent another email !!! .
cya
How long does it take to recover the new firmware?
Let me know, if on all other modes the fan is running normal?
And sorry for that problems!
well to start with i can't down load any thing it keeps saying this to me
Sorry, you have reached the download limit for this file.
if there is no limits on down loads why i do keep getting the above .
your site is so hard to understand because the translator you all use when i use it, does not work to well. i end up using google translator which actually works better then one you all use or seems to if you use the same one it''s not set up right or something .
I hope you don't think i have to pay another 20 bucks for software that never worked right to start with . beyond that let me know . Please !!! .
last thought clicking this : http://www.mintorro.com goes to a dead page or i get this:
Forbidden
You don't have permission to access / on this server.
Apache/2.4.20 (Ubuntu) Server at www.mintorro.com Port 80
i was able to read the site enough to get flash but now after i do it how you said here i get this
recovering now
Warning: session_start(): Cannot send session cookie - headers already sent by (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: session_start(): Cannot send session cache limiter - headers already sent (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: Cannot modify header information - headers already sent by (output started at /www/index.php:23) in /www/index.php on line 32
Honestly i don't see how this is much better then before the fan still spins at a 100 % all the time but now i can't even access anything on my S5 to lower the fan speed and will have to do a hard ware reset and hope that works if it doesn't then the SD way , if that does i do have a BB laying around as backup , i hope i just didn't thrash the BB on the miner now .
also i don't use the July firmware from bitmain it sucks worse then the ones before it i do use the may 2015 version forked from nicehash sense it works better then any version bitmain put out and not the July 15 2015 version you all may have , i see i may have to update to for this to work right ?. I really want to use this software but at this point in time it's shit and i can't say i have anything good to say about it , till it really works like it should out of the box GL .. I normally don't have issue picking some thing up.
I sent another email !!! .
cya
Sorry, you have reached the download limit for this file.
if there is no limits on down loads why i do keep getting the above .
your site is so hard to understand because the translator you all use when i use it, does not work to well. i end up using google translator which actually works better then one you all use or seems to if you use the same one it''s not set up right or something .
I hope you don't think i have to pay another 20 bucks for software that never worked right to start with . beyond that let me know . Please !!! .
last thought clicking this : http://www.mintorro.com goes to a dead page or i get this:
Forbidden
You don't have permission to access / on this server.
Apache/2.4.20 (Ubuntu) Server at www.mintorro.com Port 80
i was able to read the site enough to get flash but now after i do it how you said here i get this
recovering now
Warning: session_start(): Cannot send session cookie - headers already sent by (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: session_start(): Cannot send session cache limiter - headers already sent (output started at /www/index.php:23) in /www/includes/inc.php on line 31
Warning: Cannot modify header information - headers already sent by (output started at /www/index.php:23) in /www/index.php on line 32
Honestly i don't see how this is much better then before the fan still spins at a 100 % all the time but now i can't even access anything on my S5 to lower the fan speed and will have to do a hard ware reset and hope that works if it doesn't then the SD way , if that does i do have a BB laying around as backup , i hope i just didn't thrash the BB on the miner now .
also i don't use the July firmware from bitmain it sucks worse then the ones before it i do use the may 2015 version forked from nicehash sense it works better then any version bitmain put out and not the July 15 2015 version you all may have , i see i may have to update to for this to work right ?. I really want to use this software but at this point in time it's shit and i can't say i have anything good to say about it , till it really works like it should out of the box GL .. I normally don't have issue picking some thing up.
I sent another email !!! .
cya
OLD MENU - FREE VERSION
CHECK DETAILS
by a click on this Menu you will be redirected to a file browser where you can see and check what files are stored inside your config
by a click on this Menu you will be redirected to a file browser where you can see and check what files are stored inside your config
- click on Dashboard > Miner > Check Details
- you get a full file browser to:
- watch and check the files about your config
- downloading them by click on them
- navigation by click on folders
DEBUG
this will crawl all your miners and output one time the request of Mining Software api (cgminer-api)
you will get detailed information about the running machines
this will crawl all your miners and output one time the request of Mining Software api (cgminer-api)
you will get detailed information about the running machines
MY BACKUPS
nothing easier than that
Making Backup
Delete Backup
Restore Backup
Find a backup
nothing easier than that
Making Backup
- click on menu ->Miner
- then on menu -> MyBackups
- click on button -> "make a Backup"
- browse the files
- click on a generated backup (download starts)
Delete Backup
- delete backups, just click on button "delete all backups"
Restore Backup
- restore your backup - > click on button "Firmware upgrade"
- choose the file you downloaded
- click on the button "run this action"
- you find it also Menu > Miner > Firmware upgrade > upload > run this action
Find a backup
- click on the sign to find a backup and enter your search string followed by hitting "enter"
COMING SOON
FEARTURE LIST
NICEHASH SUPPORT
Our build is ready, Cgminer 4.9.2 is running stable since 20th June with extra nonce support. One of our Antminer S7 is running on it, check here:
MinToRRo Antminer S7: Details on NiceHash (see details)
check if xnsub enabled ("algo":1)
_______________________________________________________________________________ ____________________________
How to setup MinToRRo with NiceHash xnsub support? - Pool Mining
(stratum+tcp://sha256.eu.nicehash.com:3334) - it depends on your location - see here https://www.nicehash.com/?p=gstarted
_______________________________________________________________________________ ____________________________
How to setup MinToRRo with NiceHash xnsub support? - Solo Mining
_______________________________________________________________________________ ____________________________
How to setup the Worker on NiceHash servers? - manual Worker / automatic Worker
Manual Worker:
Automatic Worker:
Our build is ready, Cgminer 4.9.2 is running stable since 20th June with extra nonce support. One of our Antminer S7 is running on it, check here:
MinToRRo Antminer S7: Details on NiceHash (see details)
check if xnsub enabled ("algo":1)
_______________________________________________________________________________ ____________________________
How to setup MinToRRo with NiceHash xnsub support? - Pool Mining
(stratum+tcp://sha256.eu.nicehash.com:3334) - it depends on your location - see here https://www.nicehash.com/?p=gstarted
- click on menu "Miner"
- click on "My local Miner"
- switch the button "NiceHash Mode" to on (green)
- setup your poolworkers
- click on "Make Overkill Mod"
- click on "Start Mining Software"
- wait for restarting, MinToRRo will you redirect to the overview page (some seconds)
_______________________________________________________________________________ ____________________________
How to setup MinToRRo with NiceHash xnsub support? - Solo Mining
- like above
- use this Address - (stratum.solo.nicehash.com:3334)
_______________________________________________________________________________ ____________________________
How to setup the Worker on NiceHash servers? - manual Worker / automatic Worker
Manual Worker:
- User = your BTC Address.
- QuoteWorker= use a dot {.} behind your User/BTC like this: 1QAUCDw2naJzCXrxfKARwDLyMx71qxQneh.Worker1
Automatic Worker:
- you find this function on Menu "my local miner" above the Pools
- click on the switch "Enable Pool Automatic Worker !" (green)
- now you have the choice between "Mac-Address" or "IP-Address"
- QuoteWorker= use a dot {.} behind your User/BTC
- check if NiceHash Mode is activated
- click on "Make Overkill Mod"
- click on "Start Mining Software"
- wait for restarting, MinToRRo will you redirect to the overview page (some seconds)
POOLS
try it: Add a Mining Pool
http://www.mintorro.com/index.php
click on the green button to add a miner or add a pool
Adding a Pool
Pool Overview on Dashboard
try it: Add a Mining Pool
http://www.mintorro.com/index.php
click on the green button to add a miner or add a pool
Adding a Pool
- click on Dashboard
- click on "add a panel" (green folder sign on the right)
- click on "add a pool"
- new panel opens now
- select a pool from the dropdown menu
- fill this form with the details you have from your pool opp
- the field "homepage" can filled with a link of your own choice
- note! Not all fields are required. It depends on your selected pool
- click on the button "save"
- you will be redirected to the Dashboard now
- the first time crawling your pool will take some seconds
- if you want it faster, refresh the page by "reload your browser (circle button) tab"
Pool Overview on Dashboard
- click on "goto" will redirect you to the link "homepage" you filled in the form before
- click on "edit" will open the pool setup form
- click on "up" sign, will hide / show the pool
- click on "X" sign, will delete the pool panel (followed by the question: "sure to delete"
- click on "url" will redirect you to the pools website
- for example "nicehash" here you will be redirected to the stats page of your wallet by clicking on "url"
Managing
DASHBORAD
CONF DIRECT
http://www.mintorro.com/cgminer-conf.php
Review your settings and save them
Restart Mining Software after review
Give him a Kick
Kill Mining Software
Reset to your old cgminer config
http://www.mintorro.com/cgminer-conf.php
Review your settings and save them
- click on > Dashboard > Miner > Cgminer.conf Direct
- new window opens
- review your settings
- make changes direct on the file
- set what ever you want (feel free) no limitations
- click on "save cgminer.conf" (it just save the settings without restart your miner!!!)
Restart Mining Software after review
- click on the button "start mining software" it will restart your mining software with the new settings
- if you are not firm with this settings, please use only the "my local miner" menu
- after clicking on start, you will be redirected to the Dashboard (it will take some seconds)
- if you cant wait, just reload the hole tab over your browser (circle sign)
Give him a Kick
- if your miner stops working and you do not want to reboot the hole miner
- just click on the button "give him a kick"
- now all diagnostics known by MinToRRo will run over and over your miner
- note the website will answer "delayed"
- on every case your miner will start mining by it self
- maximum time (5 minutes)
Kill Mining Software
- by click on this button
- the mining software will be killed and stops working for 5 Minutes
- after this time it starts from it self again!
Reset to your old cgminer config
- by click on this button
- it will delete all your settings
- grabbing your config from your first time upgrade to MinToRRo
- note the miner will start with your old settings after click on "start mining software"
- before "reset to old" please backup your live datas over > Dashboard > Miner > My Backups
Settings Menu
Menu: -> Dashboard -> Miner -> My local Miner
Here you can setup your miner to run with the settings of your choice
Overview
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
Menu: -> Dashboard -> Miner -> My local Miner
Here you can setup your miner to run with the settings of your choice
Overview
- NiceHash Mode
- switch on and off this mode
- select MinToRRo: 4.9.2 (green), please
- at the end to activate it click "Make Overkill Mod"
- Use backup driver
- your old driver was stored on the folder /config
- only use this if your miner really not hashing
- enable the old on (green)
- disable the old on (red) = default
- works with every Make Mod
----------------------------------------------------------------------------
- Miner Type
- on first time setup let it on S7 until you click on Make a Mod
- Selection
- Antminer S7
- Antminer S5
- after first time "Make mod" the table for the S5 frequency will appear
----------------------------------------------------------------------------
- MinToRRo: 4.9.2 (green)
- Green is for:
- Overkill Mode
- Nicehash Mode
- MinToRRo: 4.8.0 (red)
- Red is for:
- Z-Mod 492
- Z-Mod 480
- OLD Mode
- Miner Mhz
- Select the MHz of your choice
- Warning! Do not use a too high MHz on your miner
- check the hardware errors
- play with the timeout
- Note! After first time click on "Make" buttons you can select other miner types and their MHZ table will appear
----------------------------------------------------------------------------
- TimeOut for Asic
- Set here the timeout for the miner hash work
- Default for S5 and S7 = 5 seconds
- controll the hashing
- if you got to much hardware errors, go higher
----------------------------------------------------------------------------
- Miner Target Temp
- The best Temp for S7 = 71C° - smashing
- just select and forget it
----------------------------------------------------------------------------
- Miner Cut Off Temp
- Default on S7 is 80C°
- just select and forget it
----------------------------------------------------------------------------
- Overvolt under Volt
- It controls the voltage
- take a look to the dropdown infos
- all my miners are running with 0600
- check your saving with an voltmeter and share your results, please
- I do not know if on 0900 the board will hash faster
- One thing I know it is possible to run on 0900 (do it on your own risk all above the default setting
- Default S5 = 0726 please use 0720
- Default S7 = 0706
----------------------------------------------------------------------------
- Fan Auto Modus
- Switch it on off
- the dropdowns will appear
- select minimum level
- select maximum level
- after setting these two values switch it ON or OFF again, please.
----------------------------------------------------------------------------
- Enable Pool Automatic Worker !
- Switch it on off
- after switch it ON an other switch will appear (IP or MAC) Worker selection
- on IP: the IP of this AntMiner will be added
- on MAC: the MAC-Address of this AntMiner will be added
- Note! Take a look to the pool providers setup instructions for the worker and add on Worker (next field) an underscore or a dot at the end
----------------------------------------------------------------------------
- Your Pool Settings
- fill all the fields Pool 1 to Pool 4
- Address! just copy and paste it
- without stratum://
- Worker = Your pool worker
- Sometimes it is a good idea to setup the ip-address of your pool (prevent DNS problems)
- Note! Take a look to the pool providers setup instructions for the worker and add on Worker (next field) an underscore or a dot at the end
----------------------------------------------------------------------------
- Your Api Port
- Default is 4028
- set and forgett it
- for security reason you can also choose any other port
- above 1024 to prevent conficts with other network port, but it depends on your network layout
- Note! Make sure that no one else can access your miner from outside
----------------------------------------------------------------------------
- Pool fallback
- Default on cgminer is 120 seconds
- that means, if your pool is not responding on this time it will be switched to an other one
- Sometimes it is a good idea to setup the ip-address of your pool (prevent DNS problems)
- Note! If all your pools are not respondig the miner will stops hashing
----------------------------------------------------------------------------
- Suggest Diff for Pools:
- Your miner will tell your pool to work on this diff
- If you set it to low it will result in many (share above) target errors
- If you set it to high it will result in a low share rate
- on Kano.is and some other they will respect your suggestion but decrease it automatically to a fair rate
- Note Warning! An over dimensioned will result in a low share rate vice versa if your miner has good look it will result into best gainings
----------------------------------------------------------------------------
- Your Btc Address:
- Fill this field with a btc wallet address
- you need this for solo mining
- you have to fill this field
- Note! If your address is wrong your miner are not able to mine on this address, but it depends on the solo-pool-provider or you mint on their pocket
----------------------------------------------------------------------------
- Api Allow Network
- for setup your AntMiner over api conecction
- W:0.0
- Allow API access only to the given list of [G:]IP[/Prefix] addresses[/subnets]
- e.g. W:192.168.0.1,10.0.0/24
- take a look to this documentation https://github.com/ckolivas/cgminer/blob/master/API-README
- Note! If you fill here wrong addresses the hole field is unreadable and every one can access your miner from outside the internet
----------------------------------------------------------------------------
- Maximum Error Rate
- Setting up this will
- coloring the dashboard panel from green to red if a problem occurred
- Note! At the start of the mining software it is sometimes RED colored
----------------------------------------------------------------------------
- Make Mod's
- This will just make the config! You have to restart the mining by your self
- The Make a Mod selection depends of your choice
- on every case it will make a valid cgminer config file which is located on /config/cgminer folder
- to review the config click on "Check your config here"
- also you can browse the hole files stored on your miner config: Dashboard > Miner > Check details Menu
- Note! If you manually edit the file and make a misstake your miner will not start working
----------------------------------------------------------------------------
- License Key:
- Nothing to do!
- it will be filled automatically by the system
----------------------------------------------------------------------------
- Upper Buttons
- Controll your Antminer
- Reboot: reboots the system
- Kill mining software: just stops the mining service, but note, that the mining control service will start it within 5 minutes from it self
- Start mining software: restarts the mining and kills old instances
- Reset to defaults: Warning! It resets your miner to the time where you upgraded the first time to MinToRRo
- Start FAN Controll App, it starts and checke the service with the settings you made above!
- Give him a kick: If you do not want to reboot your miner it will run several scripts to recover your hash boards.
- Note! On every case your miner will come back! But sometimes it is faster to reboot the hole system
----------------------------------------------------------------------------
- Warning! Read this button
- please read carefully the hole text
- if you have any problems please write us an email or a pm here
- Note! Read and understand the warnings! You can damage your miner with a to high MHZ or wrong Voltage!
Screen Shots
DEMO VIDEOS
HOW TO USE
Benefits?
- After upgrading to MinToRRo your Bitmain Antminer is mining directly after reboot with your own old settings
- Changing and playing with the settings you find on Menu ->"Miner" ->My local Miner
- Setup the first time MinToRRo
- Click on Make Mode
- Check your Settings -> Menu -> Miner -> Conf-Direct
- Click on "Start mining Software"
- wait some seconds for respond of the Mining Api
- Check the results on top menu -> Dashboard
Benefits?
- Your miner will deliver nearly 99,8% good and valid shares
- Hardware errors nearly eliminated!
- MinToRRo is ready for halving
- over and under volt
It can recovering all now!
Download the file SD-CARD IMAGE from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
There are no limitations!
Note: This Version is only for recovering, it does not contain the brand new MinToRRo it's really only for recovering!
MinToRRo it self is designed to run perfect with the StepOne.tar for upgrading and Mintorro-Update.tar.
How to RECOVER on Windows Computer
- Download the SD-Image
- Download and install Win32-SD imager https://sourceforge.net/projects/win32diskimager/
- download 7zip (link)on your computer
- right click on this file and select unzip with 7zip from the context menu
- unzip the uSD-Image (password: zwilla)
- Plug your uSD-Card into your Windows computer
- open Win32-Imager
- select the SD-Image
- click on burning
- after complete burning, secure unplug your SD-Card
- switch off the Miner, plug the SD into the Antminer slot
- switch your Miner on
- after reboot click on the button "Old Menu"
- follow now this steps https://bitcointalksearch.org/topic/m.15218506
How to RECOVER on Ubuntu
- Download the SD-Image
- Plug your uSD-Card into your Ubuntu computer
- unzip the uSD-Image (password: zwilla)
- ImageBurner will open automatically after unzipping
- select your SD-Card as destination
- click on burning
- after complete burning, secure unplug your SD-Card
- switch off the Miner, plug the SD into the Antminer slot
- switch your Miner on
- after reboot click on the button "Old Menu"
- follow now this steps https://bitcointalksearch.org/topic/m.15218506
NOTE!
Do not use this Recovery version for Mining![/list]
on SALE now!
UPDATE - CORE
Means updating an existing MinToRRO Firmware! (not from SD-Card Zwilla Mod)
UPDATE - APP
UPDATE - CORE
Means updating an existing MinToRRO Firmware! (not from SD-Card Zwilla Mod)
- Download the file Update from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
- Click on Miner
- Click on Firmware upgrade
- Upload the file Mintorro-Update-Core.tar
- Click on the button "Run this Action"
- This process is unruinable, on every case (lost network, power off, aso. ) your miner will be up within 3 Minutes and starts mining with YOUR pool datas
UPDATE - APP
- Click on Miner
- Click on Firmware upgrade
- Upload the file Mintorro-Update-APP.tar
- Click on the button "Run this Action"
- No - and never a reboot is needed
- or just click on the Button "Update App"
HOW TO INSTALL?
_______________________________________________________________________________ ____________________________
UPGRADE
Means upgrading from old Bitmain Antminer Firmware to MinToRRO! (not from SD-Card Zwilla Mod)
Download the file Upgrade from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
You have to "https://your.miner.ip." to login now!
Take a look to this video https://youtu.be/-fPufy8Pf2E how it works live!
NOTE!
If you want to upgrade more than 100 Antminers at once please contact us we will make and send you a personal upgrade script!
_______________________________________________________________________________ ____________________________
UPGRADE
Means upgrading from old Bitmain Antminer Firmware to MinToRRO! (not from SD-Card Zwilla Mod)
Download the file Upgrade from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
- Go on the old Firmware to menu -> SYSTEM -> Upgrade
- Click on "Restore backup:"
- Choose now the File: "Mintorro-SetpOne.tar"
- Click on "upload Archive" now
- please wait now for up to 5 minutes
- on first shutdown (about 90 seconds) please close your bowser window or click on an other tab of bitmain old menu
- Note! Your Miner talking now over https to your browser!!!
- Now you can login and setting up what you want!
- Login: your customer email address and Password: what you want
You have to "https://your.miner.ip." to login now!
Take a look to this video https://youtu.be/-fPufy8Pf2E how it works live!
NOTE!
If you want to upgrade more than 100 Antminers at once please contact us we will make and send you a personal upgrade script!
on SALE now!
Custom Firmware for Bitmain Antminer S5 and S7
Website: http://www.mintorro.com
More later!
Take a look on:
LICENSE:
There is a free version included (old Menu), if you want only to use the free version? Stay on the old firmware!
All new Zwilla functions you can get with the none free version!
Source Code? No problem! Open your miner (ssh) $ cd / and review what you want!
Custom Firmware for Bitmain Antminer S5 and S7
Website: http://www.mintorro.com
More later!
Take a look on:
LICENSE:
There is a free version included (old Menu), if you want only to use the free version? Stay on the old firmware!
All new Zwilla functions you can get with the none free version!
Source Code? No problem! Open your miner (ssh) $ cd / and review what you want!
on SALE now!
Custom Firmware for Bitmain Antminer S5 and S7
S9 (we need the Firmware / Miner at first, then we release the S9 support)
Website: http://www.mintorro.com live system!
German support here: https://bitcointalksearch.org/topic/biete-antminer-s7-and-s5-custom-firmware-all-batches-1299240
What is MinToRRo?
MinToRRo is not only a software, it is a firmware release for all Antminer S5 and Antminer S7 for all batches.
_______________________________________________________________________________ ____________________________
Take a look on:
_______________________________________________________________________________ ____________________________
LICENSE: https://bitcointalksearch.org/topic/m.15218497
There is a free version included (old Menu), if you want only to use the free version? Stay on the old firmware!
All new Zwilla functions you can get with the none free version!
Source Code? No problem! Open your miner (ssh) $ cd / and review what you want!
_______________________________________________________________________________ ____________________________
_______________________________________________________________________________ ____________________________
NEWS
HOW TO INSTALL and USE!?
_______________________________________________________________________________ ____________________________
UPGRADE https://bitcointalksearch.org/topic/m.15218506
Means upgrading from old Bitmain Antminer Firmware to MinToRRO! (not from SD-Card Zwilla Mod)
Download the file Upgrade from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
_______________________________________________________________________________ ____________________________
UPDATE https://bitcointalksearch.org/topic/m.15218510
Means updating an existing MinToRRO Firmware! (not from SD-Card Zwilla Mod)
Download the file Update from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
_______________________________________________________________________________ ____________________________
RECOVERY https://bitcointalksearch.org/topic/m.15218516
It can recovering all now!
Download the file SD-CARD IMAGE from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
There are no limitations,
_______________________________________________________________________________ ____________________________
HOW TO USE https://bitcointalksearch.org/topic/m.15218521
_______________________________________________________________________________ ____________________________
DEMO VIDEOS https://bitcointalksearch.org/topic/m.15218524
_______________________________________________________________________________ ____________________________
Screen Shots https://bitcointalksearch.org/topic/m.15218528
_______________________________________________________________________________ ____________________________
Settings Menu https://bitcointalksearch.org/topic/m.15218533
_______________________________________________________________________________ ____________________________
CONF DIRECT https://bitcointalksearch.org/topic/m.15218535
_______________________________________________________________________________ ____________________________
NETWORK https://bitcointalksearch.org/topic/m.15218539
_______________________________________________________________________________ ____________________________
DASBOARD https://bitcointalksearch.org/topic/m.15218544
_______________________________________________________________________________ ____________________________
Managing https://bitcointalksearch.org/topic/m.15218551
_______________________________________________________________________________ ____________________________
POOLS https://bitcointalksearch.org/topic/m.15218556
_______________________________________________________________________________ ____________________________
NICEHASH SUPPORT https://bitcointalksearch.org/topic/m.15218560
After review and agreement, the Team of NiceHash we will release this firmware for their customers !
(cgminer 4.9.2 --extranonce-subscribe is ready for Bitmain Antminers S5 and S7. It is running now stable since 20th June 09:00 )
(click the link to see how to, please )
_______________________________________________________________________________ ____________________________
FEARTURE LIST https://bitcointalksearch.org/topic/m.15218564
_______________________________________________________________________________ ____________________________
COMING SOON https://bitcointalksearch.org/topic/m.15218572
_______________________________________________________________________________ ____________________________
MY BACKUPS https://bitcointalksearch.org/topic/m.15218576
_______________________________________________________________________________ ____________________________
DEBUG https://bitcointalksearch.org/topic/m.15218579
_______________________________________________________________________________ ____________________________
CHECK DETAILS https://bitcointalksearch.org/topic/m.15218585
_______________________________________________________________________________ ____________________________
OLD MENU - FREE VERSION https://bitcointalksearch.org/topic/m.15218591
_______________________________________________________________________________ ____________________________
Removing MinToRRo from your Antminer
_______________________________________________________________________________ ____________________________
_______________________________________________________________________________ ____________________________
Custom Firmware for Bitmain Antminer S5 and S7
S9 (we need the Firmware / Miner at first, then we release the S9 support)
Website: http://www.mintorro.com live system!
German support here: https://bitcointalksearch.org/topic/biete-antminer-s7-and-s5-custom-firmware-all-batches-1299240
What is MinToRRo?
MinToRRo is not only a software, it is a firmware release for all Antminer S5 and Antminer S7 for all batches.
_______________________________________________________________________________ ____________________________
Take a look on:
_______________________________________________________________________________ ____________________________
LICENSE: https://bitcointalksearch.org/topic/m.15218497
There is a free version included (old Menu), if you want only to use the free version? Stay on the old firmware!
All new Zwilla functions you can get with the none free version!
Source Code? No problem! Open your miner (ssh) $ cd / and review what you want!
_______________________________________________________________________________ ____________________________
_______________________________________________________________________________ ____________________________
NEWS
- 02. July 2016 - New StepOne.tar and so on (all portal files are updated)
- 28. June 2016 - Full automatic Relax Mode - Temperatur and Fan Control
- 23. June 2016 - New Update System - Now we never need a restart or reboot to update your miner!
- 21. June 2016 - Test - NiceHash Mode (extra nonce support) is running perfect on
HOW TO INSTALL and USE!?
_______________________________________________________________________________ ____________________________
UPGRADE https://bitcointalksearch.org/topic/m.15218506
Means upgrading from old Bitmain Antminer Firmware to MinToRRO! (not from SD-Card Zwilla Mod)
Download the file Upgrade from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
_______________________________________________________________________________ ____________________________
UPDATE https://bitcointalksearch.org/topic/m.15218510
Means updating an existing MinToRRO Firmware! (not from SD-Card Zwilla Mod)
Download the file Update from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
_______________________________________________________________________________ ____________________________
RECOVERY https://bitcointalksearch.org/topic/m.15218516
It can recovering all now!
Download the file SD-CARD IMAGE from your account on https://www.zwilla.de/de/downloads/custom-firmware-antminer-s7/
There are no limitations,
_______________________________________________________________________________ ____________________________
HOW TO USE https://bitcointalksearch.org/topic/m.15218521
_______________________________________________________________________________ ____________________________
DEMO VIDEOS https://bitcointalksearch.org/topic/m.15218524
_______________________________________________________________________________ ____________________________
Screen Shots https://bitcointalksearch.org/topic/m.15218528
_______________________________________________________________________________ ____________________________
Settings Menu https://bitcointalksearch.org/topic/m.15218533
_______________________________________________________________________________ ____________________________
CONF DIRECT https://bitcointalksearch.org/topic/m.15218535
_______________________________________________________________________________ ____________________________
NETWORK https://bitcointalksearch.org/topic/m.15218539
_______________________________________________________________________________ ____________________________
DASBOARD https://bitcointalksearch.org/topic/m.15218544
_______________________________________________________________________________ ____________________________
Managing https://bitcointalksearch.org/topic/m.15218551
_______________________________________________________________________________ ____________________________
POOLS https://bitcointalksearch.org/topic/m.15218556
_______________________________________________________________________________ ____________________________
NICEHASH SUPPORT https://bitcointalksearch.org/topic/m.15218560
After review and agreement, the Team of NiceHash we will release this firmware for their customers !
(cgminer 4.9.2 --extranonce-subscribe is ready for Bitmain Antminers S5 and S7. It is running now stable since 20th June 09:00 )
(click the link to see how to, please )
_______________________________________________________________________________ ____________________________
FEARTURE LIST https://bitcointalksearch.org/topic/m.15218564
_______________________________________________________________________________ ____________________________
COMING SOON https://bitcointalksearch.org/topic/m.15218572
_______________________________________________________________________________ ____________________________
MY BACKUPS https://bitcointalksearch.org/topic/m.15218576
_______________________________________________________________________________ ____________________________
DEBUG https://bitcointalksearch.org/topic/m.15218579
_______________________________________________________________________________ ____________________________
CHECK DETAILS https://bitcointalksearch.org/topic/m.15218585
_______________________________________________________________________________ ____________________________
OLD MENU - FREE VERSION https://bitcointalksearch.org/topic/m.15218591
_______________________________________________________________________________ ____________________________
Removing MinToRRo from your Antminer
- click on old Menu
- click on upgrade
- on Menu "Flash new firmware image" choose your original Bitmain Firmware
- enable "keep settings"
- click on "Flash image"
- wait for reboot
_______________________________________________________________________________ ____________________________
_______________________________________________________________________________ ____________________________
Jump to: