Someone make a pool yet? 
If I would stop puttering around the board and finish up my registration and payout code.
,I would be more than happy to open a pool to give the code a good testing. 
Topic: [NEW CURRENCY] Maria 2.0 was banned, here is her proof. The birth of Bytecoin! - page 46. (Read 106432 times)
April 02, 2013, 12:25:47 PM
If I would stop puttering around the board and finish up my registration and payout code.
,I would be more than happy to open a pool to give the code a good testing. 
April 02, 2013, 12:23:13 PM
Someone make a pool yet?
April 02, 2013, 12:19:38 PM
Yes, the quick new blocks are normal for now due to low diffculty compared to hash.
I would be more concerned about your GPU temps in combination with a low intensity of 1 (Using an intensity of 1 is most likely the reason for the low hash rates that are showing)
I would look at your hardware configuration and figure out how to get those temps down and increase your intensity setting.
Added:
For example, one of my rigs show up like this:
Code:
cgminer version 2.11.2 - Started: [2013-04-02 12:03:54]
--------------------------------------------------------------------------------
ST: 2 SS: 0 DW: 0 NB: 1 LW: 8 GF: 0 RF: 0 WU: 60.0
Connected to cryptocoinmine.com diff 64 with LP as user xxxx
Block: 07a09bd37d6eb7f1... Diff:64 Started: [12:03:54] Best share: 9
--------------------------------------------------------------------------------
[P]ool management [G]PU management [S]ettings [D]isplay options [Q]uit
GPU 0: 58.0C 3426RPM | 334.9M/1.468Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 1: 46.5C 3137RPM | 304.2M/1.228Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 2: 54.5C 65% | 304.1M/1.197Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
ST: 2 SS: 0 DW: 0 NB: 1 LW: 8 GF: 0 RF: 0 WU: 60.0
Connected to cryptocoinmine.com diff 64 with LP as user xxxx
Block: 07a09bd37d6eb7f1... Diff:64 Started: [12:03:54] Best share: 9
--------------------------------------------------------------------------------
[P]ool management [G]PU management [S]ettings [D]isplay options [Q]uit
GPU 0: 58.0C 3426RPM | 334.9M/1.468Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 1: 46.5C 3137RPM | 304.2M/1.228Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 2: 54.5C 65% | 304.1M/1.197Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
--------------------------------------------------------------------------------
And that is a fresh start, not completely up to speed. The numbers are closer to 400 m/H per card when start up is stabilized.
Well, this is laptop with dual radeon 6470... I think this Mh/s is quite good :-P
I wondered if this configuration is ok because it says "New block detected on network" but no coins in wallet...
April 02, 2013, 12:18:26 PM
No matter what I do, I get the same error in GUIMiner,
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
Make sure your bytecoin.conf includes this line:
rpcallowip=*
also Diablo Miner is better for mining Bytecoin.
That didn't help, same issue
EDIT:
rpcallowip=192.168.1.* Didn't work either
The only other thing I can think of at the moment is if you are using a daemon on a separate computer (host) that a firewall rule is blocking the connection.
I generally only use Cgminer, so there may be some quirk in the other mining programs that I am not aware of.
Also 192.168.1.* is only an example, you have to tailor it to whatever subnet your local network is using. 192.168.1.0 just happens to be the most common subnet used in home networks.
April 02, 2013, 12:17:27 PM
Yes, the quick new blocks are normal for now due to low diffculty compared to hash.
I would be more concerned about your GPU temps in combination with a low intensity of 1 (Using an intensity of 1 is most likely the reason for the low hash rates that are showing)
I would look at your hardware configuration and figure out how to get those temps down and increase your intensity setting.
Added:
For example, one of my rigs show up like this:
Code:
cgminer version 2.11.2 - Started: [2013-04-02 12:03:54]
--------------------------------------------------------------------------------
ST: 2 SS: 0 DW: 0 NB: 1 LW: 8 GF: 0 RF: 0 WU: 60.0
Connected to cryptocoinmine.com diff 64 with LP as user xxxx
Block: 07a09bd37d6eb7f1... Diff:64 Started: [12:03:54] Best share: 9
--------------------------------------------------------------------------------
[P]ool management [G]PU management [S]ettings [D]isplay options [Q]uit
GPU 0: 58.0C 3426RPM | 334.9M/1.468Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 1: 46.5C 3137RPM | 304.2M/1.228Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 2: 54.5C 65% | 304.1M/1.197Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
ST: 2 SS: 0 DW: 0 NB: 1 LW: 8 GF: 0 RF: 0 WU: 60.0
Connected to cryptocoinmine.com diff 64 with LP as user xxxx
Block: 07a09bd37d6eb7f1... Diff:64 Started: [12:03:54] Best share: 9
--------------------------------------------------------------------------------
[P]ool management [G]PU management [S]ettings [D]isplay options [Q]uit
GPU 0: 58.0C 3426RPM | 334.9M/1.468Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 1: 46.5C 3137RPM | 304.2M/1.228Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 2: 54.5C 65% | 304.1M/1.197Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
--------------------------------------------------------------------------------
And that is a fresh start, not completely up to speed. The numbers are closer to 400 m/H per card when start up is stabilized.
Well, this is laptop with dual radeon 6470... I think this Mh/s is quite good :-P
I wondered if this configuration is ok because it says "New block detected on network" but no coins in wallet...
April 02, 2013, 12:12:24 PM
But seriously now: This is just RUC with a new name and a whole fresh wave of sheeple working themselves into a mindless circlejerk over it. Once the hype dies, so will this "new" coin. Enjoy it while it lasts, I guess...
RUC was premined - 2 000 000 RUC.
Point taken.
However, my main criticism still stands: Bytecoin offers no improvements over Bitcoin, and I still think it will die in a very short amount of time.
But , but ... its green !
April 02, 2013, 12:11:43 PM
But seriously now: This is just RUC with a new name and a whole fresh wave of sheeple working themselves into a mindless circlejerk over it. Once the hype dies, so will this "new" coin. Enjoy it while it lasts, I guess...
RUC was premined - 2 000 000 RUC.
Point taken.
However, my main criticism still stands: Bytecoin offers no improvements over Bitcoin, and I still think it will die in a very short amount of time.
April 02, 2013, 12:09:26 PM
No matter what I do, I get the same error in GUIMiner,
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
Make sure your bytecoin.conf includes this line:
rpcallowip=*
also Diablo Miner is better for mining Bytecoin.
That didn't help, same issue
EDIT:
rpcallowip=192.168.1.* Didn't work either
April 02, 2013, 12:08:51 PM
No matter what I do, I get the same error in GUIMiner,
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
Make sure your bytecoin.conf includes this line:
rpcallowip=*
also Diablo Miner is better for mining Bytecoin.
rpcallowip=* is NOT a good idea from a security standpoint as it will allow anybody that can reach the daemon (in or out of your local network) to use rpc commands.
You need to limit the scope (like I mentioned earlier) with the wildcard being at most the last digit of the IP (example: 192.168.1.*)
April 02, 2013, 12:06:01 PM
No matter what I do, I get the same error in GUIMiner,
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
Make sure your bytecoin.conf includes this line:
rpcallowip=*
also Diablo Miner is better for mining Bytecoin.
April 02, 2013, 12:04:28 PM
No matter what I do, I get the same error in GUIMiner,
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
When I try to solo mine I get this error in GUIMiner
[Errno 10061] No connection could be made because the target machine actively refused it
April 02, 2013, 11:59:01 AM
Question:
Is this normal?
Is this normal?
Yes, the quick new blocks are normal for now due to low diffculty compared to hash.
I would be more concerned about your GPU temps in combination with a low intensity of 1 (Using an intensity of 1 is most likely the reason for the low hash rates that are showing)
I would look at your hardware configuration and figure out how to get those temps down and increase your intensity setting.
Added:
For example, one of my rigs show up like this:
Code:
cgminer version 2.11.2 - Started: [2013-04-02 12:03:54]
--------------------------------------------------------------------------------
ST: 2 SS: 0 DW: 0 NB: 1 LW: 8 GF: 0 RF: 0 WU: 60.0
Connected to cryptocoinmine.com diff 64 with LP as user xxxx
Block: 07a09bd37d6eb7f1... Diff:64 Started: [12:03:54] Best share: 9
--------------------------------------------------------------------------------
[P]ool management [G]PU management [S]ettings [D]isplay options [Q]uit
GPU 0: 58.0C 3426RPM | 334.9M/1.468Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 1: 46.5C 3137RPM | 304.2M/1.228Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
GPU 2: 54.5C 65% | 304.1M/1.197Gh/s | A:0 R:0 HW:0 U:0.00/m I: 5
--------------------------------------------------------------------------------
And that is a fresh start, not completely up to speed. The numbers are closer to 400 m/H per card when start up is stabilized.
April 02, 2013, 11:58:39 AM
Allright then.
I never had a chance to solo mine bitcoin, so I'm playing with this now and I'm not much familiar with setup/configuration...
thx
April 02, 2013, 11:58:01 AM
So who has the most BTE right now?
I currently have 2410.75 BTE.
I currently have 2595.9895 BTE
April 02, 2013, 11:57:27 AM
So who has the most BTE right now?
I currently have 2410.75 BTE.
April 02, 2013, 11:57:11 AM
Can we have multiple connections to our bytecoin solo server?
Here's my config
Here's my config
Code:
server=1
rpcuser=ebildude123
rpcpassword=pass
rpcallowip=*
rpcport=6960
April 02, 2013, 11:55:26 AM
April 02, 2013, 11:55:06 AM
But seriously now: This is just RUC with a new name and a whole fresh wave of sheeple working themselves into a mindless circlejerk over it. Once the hype dies, so will this "new" coin. Enjoy it while it lasts, I guess...
RUC was premined - 2 000 000 RUC.
April 02, 2013, 11:55:00 AM
So who has the most BTE right now?
April 02, 2013, 11:54:12 AM
Question:
Is this normal?
Is this normal?
Jump to: