Topic: Offering support for 2nd Gen 55nm Avalon (Read 1904 times)
I found it in a tangle of cables and free cpu connector at the other two connectors ........ but I do not know where to connect them.
aww I should have probably posted my question here instead... https://bitcointalksearch.org/topic/avalon-200-clone-hash-rate-discrepancies-438714
One thing I didn't mention in the thread was that I had it on "balance" - just switched to failover but it doesn't seem to have any effect, I'll check back in an hour or so..
thanks for any help you can provide!
One thing I didn't mention in the thread was that I had it on "balance" - just switched to failover but it doesn't seem to have any effect, I'll check back in an hour or so..
thanks for any help you can provide!
honestly no, I feel ...... but what I think and strange, and that the 9-10 and 0, and also the 15-16 ............ but try 'to control the various connections
I did the firmware upgrade ..... but I always some miners to 0 ...... You have other things to try?
sounds like you have some faulty chips or not connected. Have you checked all connections to the controller board?
I did the firmware upgrade ..... but I always some miners to 0 ...... You have other things to try?
If you don't have the chip option then you are using the wrong firmware for sure.
Could you post a link to the correct firmware?
studio1one hello, I have just received my .......... but I have some of the 16 miners to 0, but some moments are 50-100 ..... they are out of service or you can do something all this ...... because I go to 150 gh / s ....I await your advice thanks
If you don't have the chip option then you are using the wrong firmware for sure.
I don't have a router, I'm using a WiFi hotspot. But I took the device to a friend who has a router, set up the IPs correctly and couldn't get the device to mine. Then I tried using the device's WiFi connectivity - still no result. I think the tplink card may not be working right. This is why I'm trying to run it through a laptop in the first place.
Edit: Also, in the screenshot above I see a setting "Avalon Chip(Default 110nm)". My interface doesn't have that line for some reason. Is there a special kind of firmware being used?
Edit: Also, in the screenshot above I see a setting "Avalon Chip(Default 110nm)". My interface doesn't have that line for some reason. Is there a special kind of firmware being used?
Not too sure, but my Avalon may be a 2nd gen, in which case my support question belongs here as well, if I may: https://bitcointalksearch.org/topic/running-200ghs-avalon-via-a-computer-435863
OK read your thread, you are doing everything not right !!
This is a standalone unit
you need to connect it to your laptop via ethernet, if it is factory set it will be 192.168.0.100
if it has been pre mined (it will have been) its IP may have been changed.
How familiar are you with networks and submasks?
Basically you need to set your ethernet IPv4 to the same subnet mask as the miner and then find its IP address
so first set your mask to 192.168.0.xxx
try using your browser to connect to
192.168.0.100
if that doesn't work get an IP scanner and scan the range
192.168.0.1 to 192.168.0.255
if its IP doesn't appear change your laptop subnet mask to 192.168.1.xxx
then run a scan on teh range 192.168.1.xxx to 192.168.1.xxx
by now you should have found its IP address.
From there you need to enter the web address to your browser and connect to the machine.
Not too sure, but my Avalon may be a 2nd gen, in which case my support question belongs here as well, if I may: https://bitcointalksearch.org/topic/running-200ghs-avalon-via-a-computer-435863
Those settings are fine, so it isn't that. Are you certain your network is set up and running. The only thing I would say is that at 1500 these can draw more than 1000W from the wall so unless you have a 1200 or more PSU I would not go above 1400.
Can you post the print out of the logs from when you save and apply CGMiner settings.
Can you post the print out of the logs from when you save and apply CGMiner settings.
Here is the config:
Also firmware is available here if you need it
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin
speed set right?
55nm set?
miner count set to 16?
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin
speed set right?
55nm set?
miner count set to 16?
Hi Studio. I have a miner that is not hashing, hope you can help. On the Cgminer Status screen the top Summary portion and section related to the Pools is loading but the bottom Avalon section says:
"This section contains no values yet"
On the Cgminer API page there are no stats coming from the Avalon units.
Any ideas?
Hi guys. Okay we figured this out, although I'm still a bit confused. The "broadcast" address in his LAN settings was 192.168.0.255 however he was on the 192.168.1.X subnet so the broadcast was incorrect. However I checked my own 230G miner and it was configured the same, and working. I'm thinking maybe re-saving the LAN settings kicked something into working. Anyway, he is happy and it's hashing now. Thanks for the help!
no not had any modules die on me.
Have you had any modules go out? Ive got three down...
Also firmware is available here if you need it
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin
speed set right?
55nm set?
miner count set to 16?
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin
speed set right?
55nm set?
miner count set to 16?
If connection is refused is his worker detail set correctly?
Jump to: