Official FutureBit Apollo BTC Software/Image and Support thread - page 144.

Philipma1957cellphone

full member

Activity: 416

Merit: 125

Quote from: achtung082 on May 28, 2021, 01:54:44 PM

Have two issues.

1) Can only set one pool.

2) All but 1 of my units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function with no unit connected and shows the default config with default pool.

Update: I was able to now get some units working again by connecting each one to the USB 1 port and booting the units individually. All but 1 of the units are now working. I will try connect the still bad unit to a PI and run it on its own.

Any advice would be greatly appreciated.

If you are downloading the block chain node you are likely stressing the cpu out

Three or four miners and a node down load may stress that cpu.

I AM almost back from the clifton mine I am hoping the node is loaded up.

achtung082

sr. member

Activity: 358

Merit: 255

Have two issues.

1) Can only set one pool.

2) All but 1 of my units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function with no unit connected and shows the default config with default pool.

Update: I was able to now get some units working again by connecting each one to the USB 1 port and booting the units individually. All but 1 of the units are now working. I will try connect the still bad unit to a PI and run it on its own.

Any advice would be greatly appreciated.

jstefanop

legendary

Activity: 2193

Merit: 1401

Quote from: Jota_US on May 27, 2021, 10:48:38 PM

Quote from: jstefanop on May 27, 2021, 08:49:55 PM

Quote from: Jota_US on May 27, 2021, 08:43:19 PM

I'm mining and also syncing but the cpu load is less than 10%.
Everything seems to work ok, how come the load is so different?
about 43% synced.

Also, I tried to connect through MiningRigRentals but for some reason the end pool (in this case slush pool) doesn't receive the hashrate, although the rig is connected to MRR. Anybody in the same situation who made it work with MRR?
I am able to make MRR work with the LTC miner without any issue.

CPU usage during block sync is directly related to your bandwidth. During our tests we were maxing out the CPU at around 5-10 MB/s.

Will check out MRR, didn’t do any testing on that pool.

Was able to make MRR work.

What was the issue in case other users want to use this pool?

jstefanop

legendary

Activity: 2193

Merit: 1401

Quote from: jchotz on May 28, 2021, 09:26:53 AM

Quote from: jstefanop on May 27, 2021, 04:55:54 PM

Quote from: jchotz on May 27, 2021, 03:12:13 PM

I just recd mine and plugged it in. It worked fine for a few minutes. When I changed the setting to allow me to edit the performance mode, I was prompted to Save & Restart. The machine won't restart even with a hard boot. Suggestions?

It takes more than the 30 second timer to restart, so just wait for the dashboard to come back up...dont keep hitting restart.

Thanks. I didn't hit restart but the once. My miner continues to be dead after power off over night and the red/green light on the front does nothing.
Please advise on how to get my new miner working.

Reach out to us on email (reply to your order email with the issue) or via chat (on shop.futurebit.io) and well get you up and running.

jchotz

newbie

Activity: 6

Merit: 0

Quote from: jstefanop on May 27, 2021, 04:55:54 PM

Quote from: jchotz on May 27, 2021, 03:12:13 PM

I just recd mine and plugged it in. It worked fine for a few minutes. When I changed the setting to allow me to edit the performance mode, I was prompted to Save & Restart. The machine won't restart even with a hard boot. Suggestions?

It takes more than the 30 second timer to restart, so just wait for the dashboard to come back up...dont keep hitting restart.

Thanks. I didn't hit restart but the once. My miner continues to be dead after power off over night and the red/green light on the front does nothing.
Please advise on how to get my new miner working.

Jota_US

newbie

Activity: 53

Merit: 0

Quote from: jstefanop on May 27, 2021, 08:49:55 PM

Quote from: Jota_US on May 27, 2021, 08:43:19 PM

I'm mining and also syncing but the cpu load is less than 10%.
Everything seems to work ok, how come the load is so different?
about 43% synced.

Also, I tried to connect through MiningRigRentals but for some reason the end pool (in this case slush pool) doesn't receive the hashrate, although the rig is connected to MRR. Anybody in the same situation who made it work with MRR?
I am able to make MRR work with the LTC miner without any issue.

CPU usage during block sync is directly related to your bandwidth. During our tests we were maxing out the CPU at around 5-10 MB/s.

Will check out MRR, didn’t do any testing on that pool.

Was able to make MRR work.

garetjax

member

Activity: 151

Merit: 10

i switched to ethernet - still only 10/32 connections - but definitely downloading blockchain faster.

Jota_US

newbie

Activity: 53

Merit: 0

Quote from: jstefanop on May 27, 2021, 08:49:55 PM

Quote from: Jota_US on May 27, 2021, 08:43:19 PM

I'm mining and also syncing but the cpu load is less than 10%.
Everything seems to work ok, how come the load is so different?
about 43% synced.

Also, I tried to connect through MiningRigRentals but for some reason the end pool (in this case slush pool) doesn't receive the hashrate, although the rig is connected to MRR. Anybody in the same situation who made it work with MRR?
I am able to make MRR work with the LTC miner without any issue.

CPU usage during block sync is directly related to your bandwidth. During our tests we were maxing out the CPU at around 5-10 MB/s.

Will check out MRR, didn’t do any testing on that pool.

Ok makes sense. Also, I don't see the option to set failover pools? Can I only put one pool?

jstefanop

legendary

Activity: 2193

Merit: 1401

Quote from: Jota_US on May 27, 2021, 08:43:19 PM

I'm mining and also syncing but the cpu load is less than 10%.
Everything seems to work ok, how come the load is so different?
about 43% synced.

Also, I tried to connect through MiningRigRentals but for some reason the end pool (in this case slush pool) doesn't receive the hashrate, although the rig is connected to MRR. Anybody in the same situation who made it work with MRR?
I am able to make MRR work with the LTC miner without any issue.

CPU usage during block sync is directly related to your bandwidth. During our tests we were maxing out the CPU at around 5-10 MB/s.

Will check out MRR, didn’t do any testing on that pool.

Jota_US

newbie

Activity: 53

Merit: 0

I'm mining and also syncing but the cpu load is less than 10%.
Everything seems to work ok, how come the load is so different?
about 43% synced.

Also, I tried to connect through MiningRigRentals but for some reason the end pool (in this case slush pool) doesn't receive the hashrate, although the rig is connected to MRR. Anybody in the same situation who made it work with MRR?
I am able to make MRR work with the LTC miner without any issue.

philipma1957

legendary

Activity: 4382

Merit: 9330

'The right to privacy matters'

Quote from: garetjax on May 27, 2021, 06:32:08 PM

How did you guys synch so fast? I'm at 59.37% Block Sync Progress, 74.91GB Blockchain Size, and 10/32 connections. I am using Wifi - but it should get 300MB on my wifi network easily. Mine got here after noontime so I didn't set it up until 1 or 2pm EST.

Fit and Finish are top notch - really like the color of the case. GUI seems pretty slick - I'm also using CK's solo pool.

wifi is always slower on long downloads like the blockchain.

Once i figured that I lost my eth connection and started it again it picked right back up.

I am now over 95gb of the chain. I had up to 30 peers before the net dropped out.

I am back to 24 or so.

I am fucking around with ways to speed up the download.

I stopped the miner. I am just running the node.

It only uses 27% of the cpu.
It only uses 10-12 watts.
vs 80% and 126-130 watts when downloading and mining ⛏

since I only need to download once I don’t mind shutting the solopool off for 6-8 hours..

garetjax

member

Activity: 151

Merit: 10

How did you guys synch so fast? I'm at 59.37% Block Sync Progress, 74.91GB Blockchain Size, and 10/32 connections. I am using Wifi - but it should get 300MB on my wifi network easily. Mine got here after noontime so I didn't set it up until 1 or 2pm EST.

Fit and Finish are top notch - really like the color of the case. GUI seems pretty slick - I'm also using CK's solo pool.

jstefanop

legendary

Activity: 2193

Merit: 1401

Quote from: philipma1957 on May 27, 2021, 05:13:20 PM

Okay I definitely corrupted the setup. the sd card is a maybe and the 500 gb nvme is a maybe .

My internet dropped out and everything froze. After 3 or 4 minutes of being frozen even though internet was back.

Nothing worked. So I pulled the power. And I now have a miner that do not connect and a node that does not connect and says I have 0 space on the 500 gb ssd stick reality is I have 411 space on the stick.

suggestions to get this back up.

My guess is a new image for the sd card so I can start from the beginning. I do have multiple empty 16gb and 32 gb samsung cards.

Good news it was an internet issue. and it is now fixed. yeh!

An internet outage would not have corrupted your setup that easy. Stats on the node won't show up correctly unless your internet is online and the node starts syncing. Just give it a few minutes and check back on it, stats will probably sync up.

philipma1957

legendary

Activity: 4382

Merit: 9330

'The right to privacy matters'

Okay I definitely corrupted the setup. the sd card is a maybe and the 500 gb nvme is a maybe .

My internet dropped out and everything froze. After 3 or 4 minutes of being frozen even though internet was back.

Nothing worked. So I pulled the power. And I now have a miner that do not connect and a node that does not connect and says I have 0 space on the 500 gb ssd stick reality is I have 411 space on the stick.

suggestions to get this back up.

My guess is a new image for the sd card so I can start from the beginning. I do have multiple empty 16gb and 32 gb samsung cards.

Good news it was an internet issue. and it is now fixed. yeh!

jstefanop

legendary

Activity: 2193

Merit: 1401

Quote from: jchotz on May 27, 2021, 03:12:13 PM

I just recd mine and plugged it in. It worked fine for a few minutes. When I changed the setting to allow me to edit the performance mode, I was prompted to Save & Restart. The machine won't restart even with a hard boot. Suggestions?

It takes more than the 30 second timer to restart, so just wait for the dashboard to come back up...dont keep hitting restart.

philipma1957

legendary

Activity: 4382

Merit: 9330

'The right to privacy matters'

Quote from: jchotz on May 27, 2021, 03:12:13 PM

I just recd mine and plugged it in. It worked fine for a few minutes. When I changed the setting to allow me to edit the performance mode, I was prompted to Save & Restart. The machine won't restart even with a hard boot. Suggestions?

I appear to have done the same.

I am busy with some other things I will get to this sooner or later.

This may be an internet issue at my home.

yxt

legendary

Activity: 3528

Merit: 1116

Why is the backend code not published under an open source license?
I mean its BTC, small nice community project...

Do not trust, verify!

jchotz

newbie

Activity: 6

Merit: 0

I just recd mine and plugged it in. It worked fine for a few minutes. When I changed the setting to allow me to edit the performance mode, I was prompted to Save & Restart. The machine won't restart even with a hard boot. Suggestions?

NotFuzzyWarm

legendary

Activity: 3892

Merit: 2797

Evil beware: We have waffles!

Quote

Source for the UI is up on my github, backend firmware is all proprietary and built from the ground up for these ASICs (ie does not use open source cgminer/bfgminer).

Kudos for that, at least Kano can't argue about that aspect Wink

jstefanop

legendary

Activity: 2193

Merit: 1401

Quote from: crypto_curious on May 27, 2021, 12:12:06 PM

Quote from: jstefanop on May 26, 2021, 11:43:45 AM

Quote from: crypto_curious on May 26, 2021, 11:32:41 AM

Thanks.
No source code will be available?
If not, then please make sure Raspberry Pi zero and 2 is available.
Some peeple use Raspbian, some Debian or Manjaro on Pis and so on. I don't know how is that all compatible with each other.
Debian uses different architecture on Pi zero than Raspbian as far as I understand.

Linux flavors dont matter, as long as the binaries are built for the architecture then it will work on all of them.

Thanks.
Will source code be available?

Source for the UI is up on my github, backend firmware is all proprietary and built from the ground up for these ASICs (ie does not use open source cgminer/bfgminer).

Topic: Official FutureBit Apollo BTC Software/Image and Support thread - page 144. (Read 53594 times)