Official FutureBit Apollo BTC Software/Image and Support thread - page 94.

amanz360

newbie

Activity: 9

Merit: 0

Quote from: mr_eee on January 01, 2022, 05:30:14 PM

I’ve had a full unit since august and it’s worked great without any issues. Recently I got a standard unit (batch 3) to connect to my full unit. I can get the standard unit mining for about 10 minutes and then it goes to inactive status. Then I have to power it off and on then restart mining to get it to start again. But it only will mine for a few minutes again before going inactive. The full unit continues mining without any issues. The red light on the standard unit has the slow red blinking light like it’s mining but it’s showing inactive in the dashboard. I’m running apollo web v0.3.2

Any ideas what the problem could be?

Hmm, yeah I've been having the same exact problem for a while. I was hoping this most recent update would fix it, but looks like I'm still having the same issue. I have 1 full unit and 2 standard units, for some reason all 3 of them wont stay hashing at the same time and one of them will drop off after a while. It's always just one that drops off and they all keep blinking the slow pattern.

austinbrady

newbie

Activity: 2

Merit: 0

Quote from: jstefanop on December 31, 2021, 09:15:09 PM

Quote from: JUST_coin on December 31, 2021, 07:47:53 PM

my apollo btc units were working fine on my preferred pool until today when suddenly it is rejecting most of the shares for 'low difficulty'.
spoke with several friends on the same mining pool with same units and they all have the same problem... scratching our heads why suddenly today this is a problem

Is this gorilla pool? Admin is in contact with us about it. Issue seems to be isolated with just their pool so could be some weird config issue on their end.

Can't wait for GP to be back fully operating with these units.

mr_eee

newbie

Activity: 7

Merit: 1

I’ve had a full unit since august and it’s worked great without any issues. Recently I got a standard unit (batch 3) to connect to my full unit. I can get the standard unit mining for about 10 minutes and then it goes to inactive status. Then I have to power it off and on then restart mining to get it to start again. But it only will mine for a few minutes again before going inactive. The full unit continues mining without any issues. The red light on the standard unit has the slow red blinking light like it’s mining but it’s showing inactive in the dashboard. I’m running apollo web v0.3.2

Any ideas what the problem could be?

jstefanop

legendary

Activity: 2188

Merit: 1401

Quote from: JUST_coin on December 31, 2021, 07:47:53 PM

my apollo btc units were working fine on my preferred pool until today when suddenly it is rejecting most of the shares for 'low difficulty'.
spoke with several friends on the same mining pool with same units and they all have the same problem... scratching our heads why suddenly today this is a problem

Is this gorilla pool? Admin is in contact with us about it. Issue seems to be isolated with just their pool so could be some weird config issue on their end.

JUST_coin

newbie

Activity: 10

Merit: 0

my apollo btc units were working fine on my preferred pool until today when suddenly it is rejecting most of the shares for 'low difficulty'.
spoke with several friends on the same mining pool with same units and they all have the same problem... scratching our heads why suddenly today this is a problem

notabeliever

hero member

Activity: 726

Merit: 504

Yes my miner has been running none stop for months now with room temperature under 40f.
I hope the next release will add the second line for pool configuration. It hurts my bottom line when the main pool is down and miner can't mine a additional one.

dwood443

jr. member

Activity: 95

Merit: 2

I just like to say my two miners are running rock solid and I'm also using wireless with no issues. Both run issue free and only restart when I choose to. I know some say an auto-restart would be nice but I've not seen the need. I will say the second miner I ordered has a error rate of 2.4% while my first is only 0.3% but performance seems ok and the error rate goes down if I run in balanced mode

crypto_curious

full member

Activity: 933

Merit: 175

Quote from: Bosiman on December 27, 2021, 04:39:19 PM

Quote

Can this be done on the command line?

How do i use comman line?

And plz another question: What should i do with the Node Dashboard? At the end its like a rudimentar Bitcoin Wallet like from Bitcoin.org?
Gr€€tz Biosman

First thing, you should open 8333 TCP port in your router and point it to 192.168.1.16. Until you do that, it's not full bitcoin node, it's restricted from accepting connections from other nodes.

Bosiman

newbie

Activity: 7

Merit: 0

Quote

Can this be done on the command line?

How do i use comman line?

And plz another question: What should i do with the Node Dashboard? At the end its like a rudimentar Bitcoin Wallet like from Bitcoin.org?
Gr€€tz Biosman

itskeule

newbie

Activity: 14

Merit: 4

Quote from: mutatrum on December 27, 2021, 12:35:17 PM

Can this be done on the command line?

If you want to disable your WiFi interface: ifconfig wlan0 down
or to disable your Ethernet: ifconfig eth0 down

Note: the commands are not boot resistant.

mutatrum

newbie

Activity: 10

Merit: 0

Quote from: jstefanop on December 22, 2021, 01:21:12 PM

Quote from: Bosiman on December 20, 2021, 04:52:38 PM

@jstefanop: This can't be correct:

Quote

Yea internal error usually has to do with no network connection, so your wifi is probably not connecting. Make sure you connecting to 2.4GHz network instead of 5 for better range

Because one of the Miner ist always on LAN, an when i connect to LAN or Wifi IP Adress, there is always this "internal message error"

Gr€€tz Biosman

This is because both interfaces are left "on" by the linux system when you use both LAN and wifi... the Web UI does not know how to deal with that currently. You need to log into the system via a monitor, and turn off the interface you are not using (drop down on the upper right corner of the desktop).

Can this be done on the command line?

Muppet007

newbie

Activity: 23

Merit: 0

Quote from: notabeliever on December 25, 2021, 05:31:57 PM

Quote from: AloTheMax on December 25, 2021, 04:02:06 PM

Yes!!!! Now I wait download the blockchain and then start to mine.... Roll Eyes

You can still mine something even though the download isn't finished.

Remember to run it on eco mode while downloading the blockchain to keep the temperature of the controller CPU down.
Once the blockchain is synced then go for balanced or turbo mode.

JUST_coin

newbie

Activity: 10

Merit: 0

Quote from: gt_addict on December 26, 2021, 06:10:06 PM

Quote from: JUST_coin on December 26, 2021, 04:02:38 PM

got 2 apollo btc units today. one is working perfectly, the second one the fan spins up but the LED in front never turns on and its never detected by usb. any ideas? thanks

Is the second unit a full unit or a “slave” unit?

they are both standard units, plugged into a pc via usb. 3 total standard units plugged into this computer, 1 I already had and the 2 new ones that showed up today. one of which I can't get the LED to turn on no matter if usb is plugged,unplugged and any psu i try. Just the fan spins

gt_addict

hero member

Activity: 2534

Merit: 623

Quote from: JUST_coin on December 26, 2021, 04:02:38 PM

got 2 apollo btc units today. one is working perfectly, the second one the fan spins up but the LED in front never turns on and its never detected by usb. any ideas? thanks

Is the second unit a full unit or a “slave” unit?

JUST_coin

newbie

Activity: 10

Merit: 0

got 2 apollo btc units today. one is working perfectly, the second one the fan spins up but the LED in front never turns on and its never detected by usb. any ideas? thanks

notabeliever

hero member

Activity: 726

Merit: 504

Quote from: AloTheMax on December 25, 2021, 04:02:06 PM

Yes!!!! Now I wait download the blockchain and then start to mine.... Roll Eyes

You can still mine something even though the download isn't finished.

AloTheMax

newbie

Activity: 7

Merit: 0

Yes!!!! Now I wait download the blockchain and then start to mine.... Roll Eyes

gt_addict

hero member

Activity: 2534

Merit: 623

Have you tried assigning it a static IP address on your router?

AloTheMax

newbie

Activity: 7

Merit: 0

No the problem is not the reception of the wifi, on the contrary the reception is 92% ... The problem is that after a while the ip address disappears and I can no longer access, from the pool it tells me that the worker is offline but the red led keeps flashing, the fan turns as if it were undermining! And to log back in I have to either reset the sd card or the router every time !!!!

ok now it has been working for more than two hours but ... I reset the sd card and I put the wifi antenna outside the metal case; at first it took some time, it seemed like it stalled or couldn't connect to the server. Now I'm just downloading the blockchain and not mining... by the way it detects me only 10/32 connections sometimes 11 this means that the port 8333 is open or not? I opened it on the router both TCP / UDP with the ip address of my futurebit, is that correct?

I was saying now I'm only downloading the blockchain and I'm not mining, maybe that's why it disconnected from the network due to a CPU overload or has nothing to do with it? Anyone who has any clarification about it thank you very much! By the way, best wishes to all of you for a Merry Christmas!!!

Bosiman

newbie

Activity: 7

Merit: 0

Is there a possibility to add a stronger and longer Wifi antenna?

I think this is the original Wifi antenna, red marked?
Is there a possibility to add an extra antenna on this connections, red marked?

To put the antenna a little bit out of the metal box, its possible, but in this cause not really a solution.

I ask, because one of the Apollo Futurebit Master Miner with 2 Slaves is behind a Fire Door and there i have no good Wifi connection. Sometimes it works, sometimes not (~15-20% connection quality.)

But it would be for me easily to put a cable under the Fire Door.....

Thx for your answers
Gr€€tz Biosman

PS: Merry christmas, catholic date, Merry christmas to all orthodox at 06.01 Kiss

Topic: Official FutureBit Apollo BTC Software/Image and Support thread - page 94. (Read 52102 times)