werent these 1.49btc?
I'm not sure what arrangements other distributers have with friedcat, but this is the best price I can offer at this point. Is there another reseller in the US with cubes in stock?
Topic: [PENDING] ASICMiner Cubes. 30-38gh/s - USA - 1 BTC - Price protection! - page 11. (Read 18205 times)
November 16, 2013, 12:29:29 PM
I'm not sure what arrangements other distributers have with friedcat, but this is the best price I can offer at this point. Is there another reseller in the US with cubes in stock?
November 16, 2013, 12:17:42 PM
werent these 1.49btc?
November 16, 2013, 10:38:48 AM
Orders made within the next hour will be shipped today.
November 16, 2013, 03:22:46 AM
Is it pretty loud, or relatively quiet?
It's not bad, I've owned an SC single and it's much quieter than one of those. It's got one fan blowing air accross 6 mini blades.
November 16, 2013, 02:58:06 AM
Is it pretty loud, or relatively quiet?
November 16, 2013, 01:50:55 AM
Ok guys I've fired one up and I've been unable to use the usb interface so far. The unit is recognized as a CP2102 USBtoUART bridge controller. I suspect the hardware ID(VID_10C4&PID_EA60) just needs to be added to bfgminer/cgminer. I'll take a look later tonight.
I've got my kill-a-watt hooked up and the only number I can provide so far is 99 watts idle. I'll be posting more pictures shortly after I get it up and running via network.
I've got my kill-a-watt hooked up and the only number I can provide so far is 99 watts idle. I'll be posting more pictures shortly after I get it up and running via network.
usb is only for debugging and firmware upgrade
November 16, 2013, 01:46:17 AM
Ok guys I've fired one up and I've been unable to use the usb interface so far. The unit is recognized as a CP2102 USBtoUART bridge controller. I suspect the hardware ID(VID_10C4&PID_EA60) just needs to be added to bfgminer/cgminer. I'll take a look later tonight.
I've got my kill-a-watt hooked up and the only number I can provide so far is 99 watts idle. I'll be posting more pictures shortly after I get it up and running via network.
I've got my kill-a-watt hooked up and the only number I can provide so far is 99 watts idle. I'll be posting more pictures shortly after I get it up and running via network.
usb is only for debugging and firmware upgrade
November 15, 2013, 11:54:41 PM
High clock averaging around 39 gh/s over last the last 12 minutes. 324 watts at the wall.
November 15, 2013, 11:35:39 PM
Ok, I've been mining for about 21 minutes (low clock) at 30.2 gh/s over network interface to a local stratum proxy.
230 watts at the wall. I'm going to kick it into overdrive now, I'll report results shortly.
230 watts at the wall. I'm going to kick it into overdrive now, I'll report results shortly.
November 15, 2013, 11:10:49 PM
Disappointing!!
Its .05 less than buying 3 blades.
Its .05 less than buying 3 blades.
Ok my math was wrong or I just anticipated the next price drop on blades !!
its .20 less than 3 blades.
Would still rather have 3 blades than that portable toaster / heat gun.
November 15, 2013, 11:04:20 PM
Disappointing!!
Its .05 less than buying 3 blades. Uses the same power (same chip so under operation should draw same power).
1 btc would be great price. At 1.75 I would rather buy 3 blades. All your eggs aren't in the same basket.
You could probably roast marshmallows out of the heat that will be rolling out of it at the power density. Which will most likely shorten
its life.
Yes, hot chips today is better than the promise of cooler/faster/more efficient ones in the future !!
Its .05 less than buying 3 blades. Uses the same power (same chip so under operation should draw same power).
1 btc would be great price. At 1.75 I would rather buy 3 blades. All your eggs aren't in the same basket.
You could probably roast marshmallows out of the heat that will be rolling out of it at the power density. Which will most likely shorten
its life.
Yes, hot chips today is better than the promise of cooler/faster/more efficient ones in the future !!
November 15, 2013, 10:55:43 PM
I would like to buy one of these soon, I'll let you know when I get a little more BTC transferred to me.
November 15, 2013, 08:33:49 PM
Also, I'm going to need to increase shipping. I may be able to fit 2 in a region C box. I could fit 2 in a large flat rate but I don't want to put them on their sides.
November 15, 2013, 08:31:22 PM
Ok guys I've fired one up and I've been unable to use the usb interface so far. The unit is recognized as a CP2102 USBtoUART bridge controller. I suspect the hardware ID(VID_10C4&PID_EA60) just needs to be added to bfgminer/cgminer. I'll take a look later tonight.
I've got my kill-a-watt hooked up and the only number I can provide so far is 99 watts idle. I'll be posting more pictures shortly after I get it up and running via network.
I've got my kill-a-watt hooked up and the only number I can provide so far is 99 watts idle. I'll be posting more pictures shortly after I get it up and running via network.
November 15, 2013, 06:28:15 PM
interested, need more details on interface, specs, etc. Compatibility with BFG/CG miner?
November 15, 2013, 05:44:30 PM
I'm interested but I'd have to know several things first:
- What is the interface (USB/LAN)? If USB, does the computer see it as one device or as multiple devices?
- What are the power requirements?
- Are any other components needed (power cable, power supply, etc.)?
- Does cgminer or other popular software support this?
November 15, 2013, 05:30:27 PM
Why trusty sellers never ship to Europe... 
because America is better ? USA! USA !but the cubes are made in China!
November 15, 2013, 05:13:11 PM
If I buy 2, the price is 3.55 btc shipped?
Correct, I may raise rates tonight as I determine best boxing stategy, but as long as you get your payment in before then, I won't change the price on you.
November 15, 2013, 04:59:30 PM
PM send regarding shipping. Thanks,
November 15, 2013, 04:49:03 PM
Why trusty sellers never ship to Europe...
because America is better ? USA! USA !but the cubes are made in China!
Jump to: