Bitcoin Forum>Bitcoin>Mining>Mining support
Author

Topic: T17 not hashing (Read 180 times)

Nthny77
newbie
Activity: 4
Merit: 1
T17 not hashing
November 11, 2021, 10:05:35 PM
#12
I opened it up and used the vacuum with light brush to clean, did not pull the hashboards out but Ill do that one day need to learn it.

I did a few more improvements on my ventilation and it looks to be running better again.
etc Taped my seals and gaps, used clamps instead of zip ties, added ducting support.

Interesting my fans speeds are now much lower, the sound is very good, like a loud bedroom fan.

SS below
https://imgur.com/a/hygPtSv
BitMaxz
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
Re: T17 not hashing
November 09, 2021, 06:21:02 PM
#11
Quote from: robertpaulsen on November 09, 2021, 01:20:49 PM
Those chip temps on board #2 look pretty high compared to pcb temp and other boards...

But still, it's far from the maximum ranges better check the temp ranges here "Miner normal operating temperature range"

Quote from: mikeywith on November 09, 2021, 04:42:21 PM
if this was another gear I would advise him to clean it, but since this is a T17, I rather not touch them if they work, I remember a bunch of heatsinks coming off when I used an air blower to clean them, it's like they installed them using saliva instead of solder.

That is why I always recommend using a brush to clean out the dust while blowing because sometimes blowing the dust without brushing cause some problems and issue.
I do recommend this brush


While slightly blowing it with air.
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: T17 not hashing
November 09, 2021, 04:42:21 PM
#10
Quote from: robertpaulsen on November 09, 2021, 01:20:49 PM
Those chip temps on board #2 look pretty high compared to pcb temp and other boards...

It's pretty normal for the chips on the middle dashboard to run slightly hotter than the other two, the difference in that picture is a bit over the average but nothing concerning to me at least, I have seen far greater variance than this, it could also be caused by something blocking the airway in the heatsink around the sensor that reports 82c.

if this was another gear I would advise him to clean it, but since this is a T17, I rather not touch them if they work, I remember a bunch of heatsinks coming off when I used an air blower to clean them, it's like they installed them using saliva instead of solder.
robertpaulsen
newbie
Activity: 20
Merit: 25
Re: T17 not hashing
November 09, 2021, 01:20:49 PM
#9
Quote from: Nthny77 on November 08, 2021, 08:36:09 PM
Here is my current status page:
https://imgur.com/a/Z3tvQ5u

Those chip temps on board #2 look pretty high compared to pcb temp and other boards...
BitMaxz
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
Re: T17 not hashing
November 09, 2021, 10:45:23 AM
#8
Quote from: Nthny77 on November 08, 2021, 08:36:09 PM
It has solved my temperature problems.
I do notice the fans are running at max rpm but I am unsure if I should be concerned.
It is operating in a box with x2 - 6inch ducts (in and out, so x4).

The status seems fine so nothing to worry about the RPM unless if you want to reduce the noise and power consumption.
You can able to change the fan speed if you want you can follow the guide from mikeywith guide here since you already have a cooling booster I guess it will stay at the same RPM.
Nthny77
newbie
Activity: 4
Merit: 1
Re: T17 not hashing
November 08, 2021, 08:36:09 PM
#7
Hello again, thank you for all the comments.

Following up on my problem I increased my ventilation with 2 of these:
https://www.amazon.ca/gp/product/B07FPFVZTZ/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

It has solved my temperature problems.
I do notice the fans are running at max rpm but I am unsure if I should be concerned.
It is operating in a box with x2 - 6inch ducts (in and out, so x4).

Here is my current status page:
https://imgur.com/a/Z3tvQ5u
BitMaxz
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
Re: T17 not hashing
October 25, 2021, 10:38:54 AM
#6
Your miner is running with the latest version of firmware according to your logs

Code:
2021-10-24 23:14:53 driver-btm-api.c:2031:bitmain_soc_init: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
2021-10-24 23:14:53 driver-btm-api.c:2032:bitmain_soc_init: commit version: 1c5be6f 2020-04-20 16:18:14, build by: lol 2020-04-23 16:35:04

So I don't think that the miner has hacked firmware. but flashing it through an SD card is worth trying.



@Nthny77
Did you properly set up your miner airflow I mean did you exhaust the heat from your miner?
If you have an exhaust and bring the heat outside this shouldn't cause "ERROR_TEMP_TOO_HIGH" or maybe robertpaulsen is right checking it physically if there are some heatsink fallen.

And another thing that I would like to suggest is to edit your whole post above and use a code tag with the icon "#" to make your thread clean not look messy.
robertpaulsen
newbie
Activity: 20
Merit: 25
Re: T17 not hashing
October 25, 2021, 04:42:48 AM
#5
It seems that one of your hashboards has decent temperature, so possibly the other two could have heatsinks fallen off. Or the fans aren't blowing in the right direction.
wndsnb
hero member
Activity: 544
Merit: 589
Re: T17 not hashing
October 24, 2021, 08:41:29 PM
#4
Chip temps are way to high for 23deg room temp. Are the fans running at full speed during startup? They should be very loud. Like hard to have a conversation in the same room loud.

I'd start by flashing stock firmware. Probably best to flash it with a SD card rather than the GUI because whoever "refurbished" your miner may have put some nasty firmware on there and you might not be able to get rid of it through the GUI.



Nthny77
newbie
Activity: 4
Merit: 1
Re: T17 not hashing
October 24, 2021, 08:23:57 PM
#3
Here is a screenshot.

https://imgur.com/a/oDMWgdI

https://imgur.com/a/oDMWgdI


Room temp is 23 degrees.
wndsnb
hero member
Activity: 544
Merit: 589
Re: T17 not hashing
October 24, 2021, 08:05:32 PM
#2
Quote from: Nthny77 on October 24, 2021, 07:10:54 PM
2021-10-24 23:19:05 thread.c:734:check_temperature: over max temp, pcb temp 72 (max 80), chip temp 104(max 103)
2021-10-24 23:19:05 driver-btm-api.c:205:set_miner_status: ERROR_TEMP_TOO_HIGH
2021-10-24 23:19:05 driver-btm-api.c:146:stop_mining: stop mining: over max temp
2021-10-24 23:19:05 thread.c:920:cancel_temperature_monitor_thread: cancel thread
2021-10-24 23:19:05 thread.c:930:cancel_read_nonce_reg_thread: cancel thread
2021-10-24 23:19:05 driver-btm-api.c:131:killall_hashboard: ****power off hashboard****

Looks like it is overheating. What is the room temperature where you're running it?

Also, what firmware is it running? 103deg C for the maximum chip temp seems too high. Thought it was normally 90deg C.

Can you post a screenshot of the status page?
Nthny77
newbie
Activity: 4
Merit: 1
Re: T17 not hashing
October 24, 2021, 07:10:54 PM
#1
Hello,

This is my first machine bought refurbished. I am having trouble getting it hashing and I am not sure what the problem is. I am using SlushPool and the worker appears on my account but is always offline. I contacted support and miner configuration looks good. The pool is alive but everything is discarded. Also my ethernet connects direct to my modem, the port is orange and should be green - I thought.

I can post any info requested.

Here is my Kernal Log, I am still learning to read them.

Code:
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203752K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25624K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12584K (cceb7000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 3266144891
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 4B3EE8FB-0A19-441D-A20E-85C2F357BFFF, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 7/4, WL threshold: 4096, image sequence number: 100324054
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 058C0E40-6EAA-4676-9C52-F694F6D34F3B, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
Oct 24 23:20:18 (none) local0.notice bmminer: set_start_time_point total_tv_start_sys=856 total_tv_end_sys=857
Oct 24 23:20:19 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_api_detect return: 0
Oct 24 23:20:20 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_update_job return: 0
Oct 24 23:20:21 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_shutdown return: 0
Oct 24 23:20:21 (none) local0.err cgminer: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: about to send detect
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: set_start_time_point total_tv_start_sys=859 total_tv_end_sys=860
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: Probing for an alive pool
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: Pool 0 difficulty changed to 8192
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: Pool 2 difficulty changed to 8192
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: LOW POWER MODE!
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: in stratum_sthread 
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: POOL 0 support ab mode!
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: Network diff set to 20.1T
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: Pool 1 difficulty changed to 8192
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: LOW POWER MODE!
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: in stratum_sthread 
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: LOW POWER MODE!
Oct 24 23:20:21 (none) local0.notice cgminer[2763]: in stratum_sthread 
Oct 24 23:20:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:20:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:20:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:20:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:20:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:20:27 (none) local0.warn cgminer[2763]: API running in IP access mode on port 4028 (14)
Oct 24 23:20:51 (none) local0.notice cgminer[2763]: Pool 0 difficulty changed to 1638
Oct 24 23:20:51 (none) local0.notice cgminer[2763]: Stratum from pool 0 requested work restart
Oct 24 23:20:51 (none) local0.notice cgminer[2763]: update job
Oct 24 23:20:51 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:20:51 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:20:51 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:20:51 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:21:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:21:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:21:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:21:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:21:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:21:51 (none) local0.notice cgminer[2763]: Pool 0 difficulty changed to 512
Oct 24 23:21:51 (none) local0.notice cgminer[2763]: Stratum from pool 0 requested work restart
Oct 24 23:21:51 (none) local0.notice cgminer[2763]: update job
Oct 24 23:21:51 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:21:51 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:21:51 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:21:51 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:22:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:22:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:22:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:22:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:22:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:22:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:22:52 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:22:52 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:22:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:22:52 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:23:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:23:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:23:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:23:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:23:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:23:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:23:52 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:23:52 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:23:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:23:52 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:24:09 (none) local0.notice cgminer[2763]: Stratum from pool 0 detected new block at height 706524
Oct 24 23:24:09 (none) local0.notice cgminer[2763]: update job
Oct 24 23:24:09 (none) local0.notice cgminer[2763]: job buf total len:2061, offset:2061
Oct 24 23:24:09 (none) local0.notice cgminer[2763]: about to send job, size is 2061
Oct 24 23:24:09 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2061
Oct 24 23:24:09 (none) local0.notice bmminer: parse job buf len:2061
Oct 24 23:24:10 (none) local0.notice cgminer[2763]: update job
Oct 24 23:24:10 (none) local0.notice cgminer[2763]: job buf total len:2446, offset:2446
Oct 24 23:24:10 (none) local0.notice cgminer[2763]: about to send job, size is 2446
Oct 24 23:24:10 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2446
Oct 24 23:24:10 (none) local0.notice bmminer: parse job buf len:2446
Oct 24 23:24:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:24:22 (none) local0.notice cgminer[2763]: job buf total len:2446, offset:2446
Oct 24 23:24:22 (none) local0.notice cgminer[2763]: about to send job, size is 2446
Oct 24 23:24:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2446
Oct 24 23:24:22 (none) local0.notice bmminer: parse job buf len:2446
Oct 24 23:24:38 (none) local0.notice cgminer[2763]: Stratum from pool 0 detected new block at height 706525
Oct 24 23:24:38 (none) local0.notice cgminer[2763]: update job
Oct 24 23:24:38 (none) local0.notice cgminer[2763]: job buf total len:2061, offset:2061
Oct 24 23:24:38 (none) local0.notice cgminer[2763]: about to send job, size is 2061
Oct 24 23:24:38 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2061
Oct 24 23:24:38 (none) local0.notice bmminer: parse job buf len:2061
Oct 24 23:24:40 (none) local0.notice cgminer[2763]: update job
Oct 24 23:24:40 (none) local0.notice cgminer[2763]: job buf total len:2382, offset:2382
Oct 24 23:24:40 (none) local0.notice cgminer[2763]: about to send job, size is 2382
Oct 24 23:24:40 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2382
Oct 24 23:24:40 (none) local0.notice bmminer: parse job buf len:2382
Oct 24 23:24:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:24:52 (none) local0.notice cgminer[2763]: job buf total len:2382, offset:2382
Oct 24 23:24:52 (none) local0.notice cgminer[2763]: about to send job, size is 2382
Oct 24 23:24:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2382
Oct 24 23:24:52 (none) local0.notice bmminer: parse job buf len:2382
Oct 24 23:25:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:25:22 (none) local0.notice cgminer[2763]: job buf total len:2414, offset:2414
Oct 24 23:25:22 (none) local0.notice cgminer[2763]: about to send job, size is 2414
Oct 24 23:25:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2414
Oct 24 23:25:22 (none) local0.notice bmminer: parse job buf len:2414
Oct 24 23:25:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:25:52 (none) local0.notice cgminer[2763]: job buf total len:2446, offset:2446
Oct 24 23:25:52 (none) local0.notice cgminer[2763]: about to send job, size is 2446
Oct 24 23:25:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2446
Oct 24 23:25:52 (none) local0.notice bmminer: parse job buf len:2446
Oct 24 23:26:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:26:22 (none) local0.notice cgminer[2763]: job buf total len:2446, offset:2446
Oct 24 23:26:22 (none) local0.notice cgminer[2763]: about to send job, size is 2446
Oct 24 23:26:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2446
Oct 24 23:26:22 (none) local0.notice bmminer: parse job buf len:2446
Oct 24 23:26:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:26:52 (none) local0.notice cgminer[2763]: job buf total len:2446, offset:2446
Oct 24 23:26:52 (none) local0.notice cgminer[2763]: about to send job, size is 2446
Oct 24 23:26:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2446
Oct 24 23:26:52 (none) local0.notice bmminer: parse job buf len:2446
Oct 24 23:27:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:27:22 (none) local0.notice cgminer[2763]: job buf total len:2446, offset:2446
Oct 24 23:27:22 (none) local0.notice cgminer[2763]: about to send job, size is 2446
Oct 24 23:27:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2446
Oct 24 23:27:22 (none) local0.notice bmminer: parse job buf len:2446
Oct 24 23:27:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:27:52 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:27:52 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:27:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:27:52 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:28:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:28:22 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:28:22 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:28:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:28:22 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:28:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:28:52 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:28:52 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:28:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:28:52 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:29:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:29:22 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:29:22 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:29:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:29:22 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:29:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:29:52 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:29:52 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:29:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:29:52 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:30:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:30:22 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:30:22 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:30:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:30:22 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:30:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:30:52 (none) local0.notice cgminer[2763]: job buf total len:2478, offset:2478
Oct 24 23:30:52 (none) local0.notice cgminer[2763]: about to send job, size is 2478
Oct 24 23:30:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2478
Oct 24 23:30:52 (none) local0.notice bmminer: parse job buf len:2478
Oct 24 23:31:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:31:22 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:31:22 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:31:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:31:22 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:31:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:31:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:31:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:31:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:31:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:32:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:32:22 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:32:22 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:32:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:32:22 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:32:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:32:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:32:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:32:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:32:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:33:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:33:22 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:33:22 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:33:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:33:22 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:33:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:33:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:33:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:33:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:33:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:34:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:34:22 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:34:22 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:34:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:34:22 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:34:48 (none) user.info kernel: macb e000b000.ethernet eth0: link down
Oct 24 23:35:37 (none) local0.notice cgminer[2763]: Stratum connection to pool 0 interrupted
Oct 24 23:35:37 (none) local0.notice cgminer[2763]: update job
Oct 24 23:35:47 (none) local0.warn cgminer[2763]: Waiting for work to be available from pools.
Oct 24 23:36:17 (none) local0.warn cgminer[2763]: Pool 0 stratum+tcp://ca.stratum.slushpool.com:3333 not responding!
Oct 24 23:37:51 (none) user.warn kernel: macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
Oct 24 23:37:51 (none) user.info kernel: macb e000b000.ethernet eth0: link up (100/Full)
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: Pool 0 successfully negotiated resume with the same session ID
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: Pool 0 difficulty changed to 8192
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: LOW POWER MODE!
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: Stratum from pool 0 requested work restart
Oct 24 23:37:52 (none) local0.warn cgminer[2763]: Work available from pools, resuming.
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:37:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:37:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:37:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:37:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:37:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:37:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:37:52 (none) local0.notice cgminer[2763]: POOL 0 support ab mode!
Oct 24 23:37:57 (none) user.info kernel: macb e000b000.ethernet eth0: link down
Oct 24 23:37:58 (none) user.warn kernel: macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
Oct 24 23:37:58 (none) user.info kernel: macb e000b000.ethernet eth0: link up (100/Full)
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: Pool 1 successfully negotiated resume with the same session ID
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: Pool 2 successfully negotiated resume with the same session ID
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: Pool 1 difficulty changed to 8192
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: Pool 2 difficulty changed to 8192
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: LOW POWER MODE!
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: LOW POWER MODE!
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: POOL 2 support ab mode!
Oct 24 23:38:02 (none) local0.notice cgminer[2763]: POOL 1 support ab mode!
Oct 24 23:38:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:38:22 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:38:22 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:38:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:38:22 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:38:52 (none) local0.notice cgminer[2763]: Pool 0 difficulty changed to 1638
Oct 24 23:38:52 (none) local0.notice cgminer[2763]: Stratum from pool 0 requested work restart
Oct 24 23:38:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:38:52 (none) local0.notice cgminer[2763]: job buf total len:2510, offset:2510
Oct 24 23:38:52 (none) local0.notice cgminer[2763]: about to send job, size is 2510
Oct 24 23:38:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2510
Oct 24 23:38:52 (none) local0.notice bmminer: parse job buf len:2510
Oct 24 23:39:22 (none) local0.notice cgminer[2763]: Pool 0 difficulty changed to 512
Oct 24 23:39:22 (none) local0.notice cgminer[2763]: Stratum from pool 0 requested work restart
Oct 24 23:39:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:39:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:39:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:39:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:39:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:39:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:39:52 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:39:52 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:39:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:39:52 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:40:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:40:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:40:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:40:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:40:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:40:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:40:52 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:40:52 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:40:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:40:52 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:41:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:41:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:41:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:41:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:41:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:41:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:41:52 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:41:52 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:41:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:41:52 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:42:22 (none) local0.notice cgminer[2763]: update job
Oct 24 23:42:22 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:42:22 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:42:22 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:42:22 (none) local0.notice bmminer: parse job buf len:2542
Oct 24 23:42:52 (none) local0.notice cgminer[2763]: update job
Oct 24 23:42:52 (none) local0.notice cgminer[2763]: job buf total len:2542, offset:2542
Oct 24 23:42:52 (none) local0.notice cgminer[2763]: about to send job, size is 2542
Oct 24 23:42:52 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4000528 size: 2542
Oct 24 23:42:52 (none) local0.notice bmminer: parse job buf len:2542
2021-10-24 23:14:53 driver-btm-api.c:663:init_freq_mode: This is scan-user version
2021-10-24 23:14:53 driver-btm-api.c:2028:bitmain_soc_init: opt_multi_version     = 1
2021-10-24 23:14:53 driver-btm-api.c:2029:bitmain_soc_init: opt_bitmain_ab        = 1
2021-10-24 23:14:53 driver-btm-api.c:2030:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-10-24 23:14:53 driver-btm-api.c:2031:bitmain_soc_init: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
2021-10-24 23:14:53 driver-btm-api.c:2032:bitmain_soc_init: commit version: 1c5be6f 2020-04-20 16:18:14, build by: lol 2020-04-23 16:35:04
2021-10-24 23:14:53 driver-btm-api.c:1844:show_sn: no SN got, please write SN to /nvdata/sn
2021-10-24 23:14:53 driver-btm-api.c:1167:miner_device_init: Detect 256MB control board of XILINX
2021-10-24 23:14:53 driver-btm-api.c:1115:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-10-24 23:14:53 thread.c:885:create_read_nonce_reg_thread: create thread
2021-10-24 23:14:59 driver-btm-api.c:1099:init_miner_version: miner ID : 81384c2c5c208814
2021-10-24 23:14:59 driver-btm-api.c:1105:init_miner_version: FPGA Version = 0xB013
2021-10-24 23:15:01 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-24 23:15:03 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-24 23:15:04 eeprom.c:431:check_pattern_test_level: L1 board
2021-10-24 23:15:04 driver-btm-api.c:737:get_product_id: product_id[0] = 1
2021-10-24 23:15:04 driver-btm-api.c:737:get_product_id: product_id[1] = 1
2021-10-24 23:15:04 driver-btm-api.c:737:get_product_id: product_id[2] = 1
2021-10-24 23:15:04 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[0] = 1
2021-10-24 23:15:04 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[1] = 1
2021-10-24 23:15:04 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[2] = 1
2021-10-24 23:15:04 driver-btm-api.c:1919:bitmain_board_init: g_ccdly_opt = 1
2021-10-24 23:15:04 driver-btm-api.c:676:_set_project_type: project:2
2021-10-24 23:15:04 driver-btm-api.c:706:_set_project_type: Project type: Antminer T17
2021-10-24 23:15:04 driver-btm-api.c:717:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-10-24 23:15:04 driver-btm-api.c:718:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-10-24 23:15:04 driver-btm-api.c:717:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-10-24 23:15:04 driver-btm-api.c:718:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-10-24 23:15:04 driver-btm-api.c:717:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-10-24 23:15:04 driver-btm-api.c:718:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-10-24 23:15:05 driver-btm-api.c:1939:bitmain_board_init: Fan check passed.
2021-10-24 23:15:07 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-10-24 23:15:11 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2021-10-24 23:15:12 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-10-24 23:15:16 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2021-10-24 23:15:18 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-10-24 23:15:21 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2021-10-24 23:15:21 thread.c:880:create_pic_heart_beat_thread: create thread
2021-10-24 23:15:21 power_api.c:55:power_init: power init ... 
2021-10-24 23:15:21 driver-btm-api.c:1949:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-10-24 23:15:53 power_api.c:232:set_iic_power_to_highest_voltage: setting to voltage: 17.00 ...
2021-10-24 23:15:59 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-24 23:16:01 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.732344 
2021-10-24 23:16:02 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.071054 
2021-10-24 23:16:04 power_api.c:86:get_average_voltage: chain[2], voltage is: 16.936347 
2021-10-24 23:16:04 power_api.c:97:get_average_voltage: aveage voltage is: 17.246582 
2021-10-24 23:16:04 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 17.000000 
2021-10-24 23:16:04 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-10-24 23:16:16 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2021-10-24 23:16:26 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2021-10-24 23:16:36 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2021-10-24 23:16:39 driver-btm-api.c:352:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0x1
2021-10-24 23:16:39 driver-btm-api.c:352:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0x1
2021-10-24 23:16:40 driver-btm-api.c:352:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0x1
2021-10-24 23:16:40 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0xb4
2021-10-24 23:16:40 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2021-10-24 23:16:40 driver-btm-api.c:1693:check_clock_counter: freq 50 clock_counter_limit 6
2021-10-24 23:16:41 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2021-10-24 23:16:41 voltage[0] = 1730
2021-10-24 23:16:41 voltage[1] = 1730
2021-10-24 23:16:41 voltage[2] = 1730
2021-10-24 23:16:41 power_api.c:140:set_working_voltage: working_voltage = 17.300000
2021-10-24 23:16:42 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2021-10-24 23:16:43 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2021-10-24 23:16:45 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2021-10-24 23:16:45 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2021-10-24 23:16:46 driver-btm-api.c:252:check_bringup_temp: Bring up temperature is 26
2021-10-24 23:16:46 thread.c:900:create_check_miner_status_thread: create thread
2021-10-24 23:16:46 thread.c:890:create_set_miner_status_thread: create thread
2021-10-24 23:16:46 driver-btm-api.c:613:calculate_timeout: dev->timeout = 392
2021-10-24 23:16:46 thread.c:875:create_temperature_monitor_thread: create thread
2021-10-24 23:16:46 freq_tuning.c:159:freq_tuning_get_max_freq: Max freq of tuning is 760
2021-10-24 23:16:46 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 18.00 ...
2021-10-24 23:17:19 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-24 23:17:21 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.989511 
2021-10-24 23:17:22 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.848681 
2021-10-24 23:17:24 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.946650 
2021-10-24 23:17:24 power_api.c:97:get_average_voltage: aveage voltage is: 17.928281 
2021-10-24 23:19:05 thread.c:734:check_temperature: over max temp, pcb temp 72 (max 80), chip temp 104(max 103)
2021-10-24 23:19:05 driver-btm-api.c:205:set_miner_status: ERROR_TEMP_TOO_HIGH
2021-10-24 23:19:05 driver-btm-api.c:146:stop_mining: stop mining: over max temp
2021-10-24 23:19:05 thread.c:920:cancel_temperature_monitor_thread: cancel thread
2021-10-24 23:19:05 thread.c:930:cancel_read_nonce_reg_thread: cancel thread
2021-10-24 23:19:05 driver-btm-api.c:131:killall_hashboard: ****power off hashboard****
2021-10-24 23:19:33 driver-btm-api.c:644:set_timeout: freq 700 final timeout=168
2021-10-24 23:19:33 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 17.30 ...
2021-10-24 23:20:00 power_api.c:124:check_voltage_multi: retry time: 0
2021-10-24 23:20:03 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.026250 
2021-10-24 23:20:06 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.854804 
2021-10-24 23:20:09 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.971142 
2021-10-24 23:20:09 power_api.c:97:get_average_voltage: aveage voltage is: 17.950732 
2021-10-24 23:20:09 frequency.c:654:get_current_min_freq: current min freq 700
2021-10-24 23:20:09 driver-btm-api.c:1693:check_clock_counter: freq 700 clock_counter_limit 89
2021-10-24 23:20:12 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 0, found 0, clock counter 0x00000000
2021-10-24 23:20:12 driver-btm-api.c:2139:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2021-10-24 23:20:12 thread.c:895:create_check_system_status_thread: create thread
2021-10-24 23:20:13 driver-btm-api.c:2155:bitmain_soc_init: Init done!
2021-10-24 23:20:13 driver-btm-api.c:205:set_miner_status: STATUS_INIT
2021-10-24 23:20:18 driver-btm-api.c:205:set_miner_status: STATUS_OKAY
2021-10-24 23:20:22 driver-btm-api.c:1325:dhash_chip_send_job: Version num 4
2021-10-24 23:37:52 driver-btm-api.c:1325:dhash_chip_send_job: Version num 1
2021-10-24 23:38:22 driver-btm-api.c:1325:dhash_chip_send_job: Version num 4
Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: