your solution is here :
https://bitcointalksearch.org/topic/repair-a-t9-after-a-bad-firmware-lost-chain-5032987
and sure read post no27
Topic: T9+ Reprogram Hashing Board Request (Read 287 times)
This is the wrong section for this, it should be in the bitcoin section.
can someone help me to bring back my two boards to life again?
Hi, still have this problem?
hi guys
i just apply this firmware to my ASIC t9+ https://bitcointalksearch.org/topic/m.42937649
and two of my board seems freezed and show zero hashing. i have only 3.5th/s that mean i have only one board alive after upgrading to this firmware.
now i was reverted back to the original bitmain t9+ firmware and used all 3 ways reset method but everything i tried was fail.
can someone help me to bring back my two boards to life again? i think they should be reprogrammed
thank
this is my kernel log
i just apply this firmware to my ASIC t9+ https://bitcointalksearch.org/topic/m.42937649
and two of my board seems freezed and show zero hashing. i have only 3.5th/s that mean i have only one board alive after upgrading to this firmware.
now i was reverted back to the original bitmain t9+ firmware and used all 3 ways reset method but everything i tried was fail.
can someone help me to bring back my two boards to life again? i think they should be reprogrammed
thank
this is my kernel log
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000303] ps7-ttc #0 at f0006000, irq=43
[ 0.000614] Console: colour dummy device 80x30
[ 0.000651] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090248] pid_max: default: 32768 minimum: 301
[ 0.090472] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090494] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.092634] CPU: Testing write buffer coherency: ok
[ 0.092981] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093040] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[ 0.093266] L310 cache controller enabled
[ 0.093286] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.171030] CPU1: Booted secondary processor
[ 0.260224] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260357] Brought up 2 CPUs
[ 0.260377] SMP: Total of 2 processors activated.
[ 0.260385] CPU: All CPU(s) started in SVC mode.
[ 0.261034] devtmpfs: initialized
[ 0.263442] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264647] regulator-dummy: no parameters
[ 0.271918] NET: Registered protocol family 16
[ 0.274179] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276445] cpuidle: using governor ladder
[ 0.276458] cpuidle: using governor menu
[ 0.283839] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.285351] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.285365] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285480] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.307462] bio: create slab at 0
[ 0.308864] vgaarb: loaded
[ 0.309560] SCSI subsystem initialized
[ 0.310762] usbcore: registered new interface driver usbfs
[ 0.310935] usbcore: registered new interface driver hub
[ 0.311200] usbcore: registered new device driver usb
[ 0.312005] media: Linux media interface: v0.10
[ 0.312159] Linux video capture interface: v2.00
[ 0.312395] pps_core: LinuxPPS API ver. 1 registered
[ 0.312406] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.312527] PTP clock support registered
[ 0.312890] EDAC MC: Ver: 3.0.0
[ 0.313912] Advanced Linux Sound Architecture Driver Initialized.
[ 0.316740] DMA-API: preallocated 4096 debug entries
[ 0.316754] DMA-API: debugging enabled by kernel config
[ 0.316840] Switched to clocksource arm_global_timer
[ 0.336826] NET: Registered protocol family 2
[ 0.337796] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.337891] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.338050] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.338110] TCP: reno registered
[ 0.338129] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.338181] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.338453] NET: Registered protocol family 1
[ 0.338818] RPC: Registered named UNIX socket transport module.
[ 0.338831] RPC: Registered udp transport module.
[ 0.338839] RPC: Registered tcp transport module.
[ 0.338848] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338861] PCI: CLS 0 bytes, default 64
[ 0.339302] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.341323] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.342719] bounce pool size: 64 pages
[ 0.343629] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.343839] msgmni has been set to 1486
[ 0.344616] io scheduler noop registered
[ 0.344629] io scheduler deadline registered
[ 0.344667] io scheduler cfq registered (default)
[ 0.356803] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.356823] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.480746] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.053349] console [ttyPS0] enabled
[ 1.057627] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.065237] [drm] Initialized drm 1.1.0 20060810
[ 1.082158] brd: module loaded
[ 1.091508] loop: module loaded
[ 1.100928] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.106680] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.114592] libphy: XEMACPS mii bus: probed
[ 1.119146] ------------- phy_id = 0x3625e62
[ 1.123882] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.132633] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.139296] ehci-pci: EHCI PCI platform driver
[ 1.146508] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.153338] usbcore: registered new interface driver usb-storage
[ 1.160201] mousedev: PS/2 mouse device common for all mice
[ 1.166292] i2c /dev entries driver
[ 1.173241] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.178782] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.184654] Xilinx Zynq CpuIdle Driver started
[ 1.189555] sdhci: Secure Digital Host Controller Interface driver
[ 1.195649] sdhci: Copyright(c) Pierre Ossman
[ 1.200016] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.206796] mmc0: no vqmmc regulator found
[ 1.210885] mmc0: no vmmc regulator found
[ 1.246857] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.255551] usbcore: registered new interface driver usbhid
[ 1.261059] usbhid: USB HID core driver
[ 1.265766] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.272065] nand: Micron MT29F2G08ABAEAWP
[ 1.276029] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281981] Bad block table found at page 131008, version 0x01
[ 1.288209] Bad block table found at page 130944, version 0x01
[ 1.294258] 3 ofpart partitions found on MTD device pl353-nand
[ 1.300044] Creating 3 MTD partitions on "pl353-nand":
[ 1.305129] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.313173] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.320491] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.329416] TCP: cubic registered
[ 1.332650] NET: Registered protocol family 17
[ 1.337362] Registering SWP/SWPB emulation handler
[ 1.343301] regulator-dummy: disabling
[ 1.347663] UBI: attaching mtd1 to ubi0
[ 1.734313] UBI: scanning is finished
[ 1.746150] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.753230] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.759993] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.766656] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.773535] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.779515] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.786622] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 862493722
[ 1.795578] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.804796] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.804801] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.808779] ALSA device list:
[ 1.808782] No soundcards found.
[ 1.825634] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.957626] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.963558] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.972689] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.982574] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.987613] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[ 2.027697] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.079822] devtmpfs: mounted
[ 2.082930] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 3.229537] random: dd urandom read with 0 bits of entropy available
[ 3.856877]
[ 3.856877] bcm54xx_config_init
[ 4.466873]
[ 4.466873] bcm54xx_config_init
[ 8.467697] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 8.473784] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 23.648077] In axi fpga driver!
[ 23.651144] request_mem_region OK!
[ 23.654536] AXI fpga dev virtual address is 0xf01fe000
[ 23.659675] *base_vir_addr = 0xc510
[ 23.674414] In fpga mem driver!
[ 23.677707] request_mem_region OK!
[ 23.681220] fpga mem virtual address is 0xf3000000
[ 24.456883]
[ 24.456883] bcm54xx_config_init
[ 25.086884]
[ 25.086884] bcm54xx_config_init
[ 29.087735] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 29.093750] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1070.665169] random: nonblocking pool is initialized
This is XILINX board. Totalram: 1039794176
Detect 1GB control board of XILINX
DETECT HW version=8000c510
miner ID : 815255ce2c008814
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x07003f0e
Find hashboard on Chain[1]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[8]
Find hashboard on Chain[9]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[1] has freq in PIC and will jump over...
Chain[1] has core num in PIC
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[8] has freq in PIC and will jump over...
Chain[8] has core num in PIC
has freq in PIC, will disable freq setting.
chain[9] has freq in PIC and will jump over...
Chain[9] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=11 on chain[1], value=870
get PIC voltage=11 on chain[2], value=870
get PIC voltage=11 on chain[3], value=870
get PIC voltage=11 on chain[8], value=870
get PIC voltage=11 on chain[9], value=870
get PIC voltage=11 on chain[10], value=870
get PIC voltage=11 on chain[11], value=870
get PIC voltage=11 on chain[12], value=870
get PIC voltage=11 on chain[13], value=870
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
set_reset_allhashboard = 0x00000000
chain[8] temp offset record: 1,0,0,0,0,0,37,28
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
chain[10] temp offset record: 1,0,0,0,0,0,37,28
chain[10] temp chip I2C addr=0x98
chain[10] has no middle temp, use special fix mode.
chain[12] temp offset record: 1,0,0,0,0,0,37,28
chain[12] temp chip I2C addr=0x98
chain[12] has no middle temp, use special fix mode.
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 9, total chain num = 9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1723 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 24 23:19:16 EST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 815255ce2c008814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=6120
get fan[2] speed=4440
get fan[5] speed=6120
get fan[2] speed=4440
get fan[5] speed=6120
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J2] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J2] test patten OK temp=-1
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J9] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J9] test patten OK temp=-1
Chain[J10] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J10] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J2] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!
Chain[J3] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J2] orignal chain_voltage_pic=11 value=870
Chain[J3] orignal chain_voltage_pic=11 value=870
Chain[J4] orignal chain_voltage_pic=11 value=870
Chain[J9] orignal chain_voltage_pic=11 value=870
Chain[J10] orignal chain_voltage_pic=11 value=870
Chain[J11] orignal chain_voltage_pic=11 value=870
Chain[J12] orignal chain_voltage_pic=11 value=870
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J2] has 0 asic
Chain[J4] has core num in PIC
Chain[J13] has core num in PIC
Chain[J14] has core num in PIC
miner total rate=3539GH/s fixed rate=3500GH/s
read PIC voltage=930 on chain[3]
Chain:3 chipnum=18
Chain[J4] voltage added=0.0V
Chain:3 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:3 max freq=575
Chain:3 min freq=575
read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Chain[J13] voltage added=0.0V
Chain:12 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:12 max freq=575
Chain:12 min freq=575
read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Chain[J14] voltage added=0.0V
Chain:13 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:13 max freq=575
Chain:13 min freq=575
Miner fix freq ...
read PIC voltage=930 on chain[3]
Chain:3 chipnum=18
Chain[J4] voltage added=0.0V
Chain:3 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:3 max freq=575
Chain:3 min freq=575
read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Chain[J13] voltage added=0.0V
Chain:12 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:12 max freq=575
Chain:12 min freq=575
read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Chain[J14] voltage added=0.0V
Chain:13 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:13 max freq=575
Chain:13 min freq=575
max freq = 575
set baud=1
Chain[J13] PIC temp offset=1,0,0,0,0,0,37,28
chain[12] temp chip I2C addr=0x98
chain[12] has no middle temp, use special fix mode.
Chain[J13] chip[0] use PIC middle temp offset=0 typeID=55
New offset Chain[12] chip[0] local:30 remote:34 offset:26
Chain[J13] chip[0] get middle temp offset=26 typeID=55
open core on chain[3] [12] [13]...
set voltage=870 on chain[3], the real voltage=870
Chain[J4] set working voltage=870 [11]
setStartTimePoint total_tv_start_sys=322 total_tv_end_sys=323
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[3]: (asic index start from 1-18)
Asic[01]=61.0690 Asic[02]=66.2360 Asic[03]=67.0240 Asic[04]=61.4040 Asic[05]=65.1960 Asic[06]=66.6890 Asic[07]=64.3400 Asic[08]=62.3440
Asic[09]=62.7300 Asic[10]=65.0110 Asic[11]=65.3300 Asic[12]=64.4410 Asic[13]=66.4880 Asic[14]=62.2930 Asic[15]=64.9610 Asic[16]=66.9570
Asic[17]=71.0850 Asic[18]=69.2560
get RT hashrate from Chain[12]: (asic index start from 1-18)
Asic[01]=70.2620 Asic[02]=68.5680 Asic[03]=70.3460 Asic[04]=63.3000 Asic[05]=63.7860 Asic[06]=67.6450 Asic[07]=66.7060 Asic[08]=65.3970
Asic[09]=69.8770 Asic[10]=59.9110 Asic[11]=69.7420 Asic[12]=67.3260 Asic[13]=59.8440 Asic[14]=62.6460 Asic[15]=68.0980 Asic[16]=67.0920
Asic[17]=65.2800 Asic[18]=64.3070
get RT hashrate from Chain[13]: (asic index start from 1-18)
Asic[01]=64.3570 Asic[02]=66.5710 Asic[03]=69.9770 Asic[04]=66.9910 Asic[05]=70.0280 Asic[06]=66.1520 Asic[07]=67.5450 Asic[08]=61.0520
Asic[09]=63.3670 Asic[10]=68.5850 Asic[11]=62.8640 Asic[12]=69.1220 Asic[13]=60.5990 Asic[14]=63.4510 Asic[15]=63.5010 Asic[16]=67.4440
Asic[17]=63.7530 Asic[18]=67.3600
Check Chain[J4] ASIC RT error: (asic index start from 1-18)
Check Chain[J13] ASIC RT error: (asic index start from 1-18)
Check Chain[J14] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
do read temp on Chain[12]
Chain[12] Chip[1] TempTypeID=55 middle offset=26
Chain[12] Chip[1] local Temp=69
Chain[12] Chip[1] middle Temp=83
Special fix Chain[12] Chip[1] middle Temp = 84
Done read temp on Chain[12]
set FAN speed according to: temp_highest=69 temp_top1[PWM_T]=69 temp_top1[TEMP_POS_LOCAL]=69 temp_change=1 fix_fan_steps=0
FAN PWM: 86
read_temp_func Done!
CRC error counter=24078
[ 0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000303] ps7-ttc #0 at f0006000, irq=43
[ 0.000614] Console: colour dummy device 80x30
[ 0.000651] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090248] pid_max: default: 32768 minimum: 301
[ 0.090472] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090494] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.092634] CPU: Testing write buffer coherency: ok
[ 0.092981] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093040] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[ 0.093266] L310 cache controller enabled
[ 0.093286] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.171030] CPU1: Booted secondary processor
[ 0.260224] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260357] Brought up 2 CPUs
[ 0.260377] SMP: Total of 2 processors activated.
[ 0.260385] CPU: All CPU(s) started in SVC mode.
[ 0.261034] devtmpfs: initialized
[ 0.263442] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264647] regulator-dummy: no parameters
[ 0.271918] NET: Registered protocol family 16
[ 0.274179] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276445] cpuidle: using governor ladder
[ 0.276458] cpuidle: using governor menu
[ 0.283839] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.285351] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.285365] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285480] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.307462] bio: create slab
[ 0.308864] vgaarb: loaded
[ 0.309560] SCSI subsystem initialized
[ 0.310762] usbcore: registered new interface driver usbfs
[ 0.310935] usbcore: registered new interface driver hub
[ 0.311200] usbcore: registered new device driver usb
[ 0.312005] media: Linux media interface: v0.10
[ 0.312159] Linux video capture interface: v2.00
[ 0.312395] pps_core: LinuxPPS API ver. 1 registered
[ 0.312406] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.312527] PTP clock support registered
[ 0.312890] EDAC MC: Ver: 3.0.0
[ 0.313912] Advanced Linux Sound Architecture Driver Initialized.
[ 0.316740] DMA-API: preallocated 4096 debug entries
[ 0.316754] DMA-API: debugging enabled by kernel config
[ 0.316840] Switched to clocksource arm_global_timer
[ 0.336826] NET: Registered protocol family 2
[ 0.337796] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.337891] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.338050] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.338110] TCP: reno registered
[ 0.338129] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.338181] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.338453] NET: Registered protocol family 1
[ 0.338818] RPC: Registered named UNIX socket transport module.
[ 0.338831] RPC: Registered udp transport module.
[ 0.338839] RPC: Registered tcp transport module.
[ 0.338848] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338861] PCI: CLS 0 bytes, default 64
[ 0.339302] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.341323] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.342719] bounce pool size: 64 pages
[ 0.343629] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.343839] msgmni has been set to 1486
[ 0.344616] io scheduler noop registered
[ 0.344629] io scheduler deadline registered
[ 0.344667] io scheduler cfq registered (default)
[ 0.356803] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.356823] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.480746] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.053349] console [ttyPS0] enabled
[ 1.057627] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.065237] [drm] Initialized drm 1.1.0 20060810
[ 1.082158] brd: module loaded
[ 1.091508] loop: module loaded
[ 1.100928] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.106680] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.114592] libphy: XEMACPS mii bus: probed
[ 1.119146] ------------- phy_id = 0x3625e62
[ 1.123882] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.132633] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.139296] ehci-pci: EHCI PCI platform driver
[ 1.146508] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.153338] usbcore: registered new interface driver usb-storage
[ 1.160201] mousedev: PS/2 mouse device common for all mice
[ 1.166292] i2c /dev entries driver
[ 1.173241] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.178782] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.184654] Xilinx Zynq CpuIdle Driver started
[ 1.189555] sdhci: Secure Digital Host Controller Interface driver
[ 1.195649] sdhci: Copyright(c) Pierre Ossman
[ 1.200016] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.206796] mmc0: no vqmmc regulator found
[ 1.210885] mmc0: no vmmc regulator found
[ 1.246857] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.255551] usbcore: registered new interface driver usbhid
[ 1.261059] usbhid: USB HID core driver
[ 1.265766] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.272065] nand: Micron MT29F2G08ABAEAWP
[ 1.276029] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281981] Bad block table found at page 131008, version 0x01
[ 1.288209] Bad block table found at page 130944, version 0x01
[ 1.294258] 3 ofpart partitions found on MTD device pl353-nand
[ 1.300044] Creating 3 MTD partitions on "pl353-nand":
[ 1.305129] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.313173] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.320491] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.329416] TCP: cubic registered
[ 1.332650] NET: Registered protocol family 17
[ 1.337362] Registering SWP/SWPB emulation handler
[ 1.343301] regulator-dummy: disabling
[ 1.347663] UBI: attaching mtd1 to ubi0
[ 1.734313] UBI: scanning is finished
[ 1.746150] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.753230] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.759993] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.766656] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.773535] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.779515] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.786622] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 862493722
[ 1.795578] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.804796] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.804801] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.808779] ALSA device list:
[ 1.808782] No soundcards found.
[ 1.825634] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.957626] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.963558] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.972689] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.982574] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.987613] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[ 2.027697] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.079822] devtmpfs: mounted
[ 2.082930] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 3.229537] random: dd urandom read with 0 bits of entropy available
[ 3.856877]
[ 3.856877] bcm54xx_config_init
[ 4.466873]
[ 4.466873] bcm54xx_config_init
[ 8.467697] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 8.473784] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 23.648077] In axi fpga driver!
[ 23.651144] request_mem_region OK!
[ 23.654536] AXI fpga dev virtual address is 0xf01fe000
[ 23.659675] *base_vir_addr = 0xc510
[ 23.674414] In fpga mem driver!
[ 23.677707] request_mem_region OK!
[ 23.681220] fpga mem virtual address is 0xf3000000
[ 24.456883]
[ 24.456883] bcm54xx_config_init
[ 25.086884]
[ 25.086884] bcm54xx_config_init
[ 29.087735] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 29.093750] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1070.665169] random: nonblocking pool is initialized
This is XILINX board. Totalram: 1039794176
Detect 1GB control board of XILINX
DETECT HW version=8000c510
miner ID : 815255ce2c008814
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x07003f0e
Find hashboard on Chain[1]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[8]
Find hashboard on Chain[9]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[1] has freq in PIC and will jump over...
Chain[1] has core num in PIC
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[8] has freq in PIC and will jump over...
Chain[8] has core num in PIC
has freq in PIC, will disable freq setting.
chain[9] has freq in PIC and will jump over...
Chain[9] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=11 on chain[1], value=870
get PIC voltage=11 on chain[2], value=870
get PIC voltage=11 on chain[3], value=870
get PIC voltage=11 on chain[8], value=870
get PIC voltage=11 on chain[9], value=870
get PIC voltage=11 on chain[10], value=870
get PIC voltage=11 on chain[11], value=870
get PIC voltage=11 on chain[12], value=870
get PIC voltage=11 on chain[13], value=870
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
set_reset_allhashboard = 0x00000000
chain[8] temp offset record: 1,0,0,0,0,0,37,28
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
chain[10] temp offset record: 1,0,0,0,0,0,37,28
chain[10] temp chip I2C addr=0x98
chain[10] has no middle temp, use special fix mode.
chain[12] temp offset record: 1,0,0,0,0,0,37,28
chain[12] temp chip I2C addr=0x98
chain[12] has no middle temp, use special fix mode.
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 9, total chain num = 9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1723 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 24 23:19:16 EST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 815255ce2c008814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=6120
get fan[2] speed=4440
get fan[5] speed=6120
get fan[2] speed=4440
get fan[5] speed=6120
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J2] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J2] test patten OK temp=-1
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J9] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J9] test patten OK temp=-1
Chain[J10] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J10] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J2] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!
Chain[J3] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J2] orignal chain_voltage_pic=11 value=870
Chain[J3] orignal chain_voltage_pic=11 value=870
Chain[J4] orignal chain_voltage_pic=11 value=870
Chain[J9] orignal chain_voltage_pic=11 value=870
Chain[J10] orignal chain_voltage_pic=11 value=870
Chain[J11] orignal chain_voltage_pic=11 value=870
Chain[J12] orignal chain_voltage_pic=11 value=870
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J2] has 0 asic
Chain[J4] has core num in PIC
Chain[J13] has core num in PIC
Chain[J14] has core num in PIC
miner total rate=3539GH/s fixed rate=3500GH/s
read PIC voltage=930 on chain[3]
Chain:3 chipnum=18
Chain[J4] voltage added=0.0V
Chain:3 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:3 max freq=575
Chain:3 min freq=575
read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Chain[J13] voltage added=0.0V
Chain:12 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:12 max freq=575
Chain:12 min freq=575
read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Chain[J14] voltage added=0.0V
Chain:13 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:13 max freq=575
Chain:13 min freq=575
Miner fix freq ...
read PIC voltage=930 on chain[3]
Chain:3 chipnum=18
Chain[J4] voltage added=0.0V
Chain:3 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:3 max freq=575
Chain:3 min freq=575
read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Chain[J13] voltage added=0.0V
Chain:12 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:12 max freq=575
Chain:12 min freq=575
read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Chain[J14] voltage added=0.0V
Chain:13 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:13 max freq=575
Chain:13 min freq=575
max freq = 575
set baud=1
Chain[J13] PIC temp offset=1,0,0,0,0,0,37,28
chain[12] temp chip I2C addr=0x98
chain[12] has no middle temp, use special fix mode.
Chain[J13] chip[0] use PIC middle temp offset=0 typeID=55
New offset Chain[12] chip[0] local:30 remote:34 offset:26
Chain[J13] chip[0] get middle temp offset=26 typeID=55
open core on chain[3] [12] [13]...
set voltage=870 on chain[3], the real voltage=870
Chain[J4] set working voltage=870 [11]
setStartTimePoint total_tv_start_sys=322 total_tv_end_sys=323
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[3]: (asic index start from 1-18)
Asic[01]=61.0690 Asic[02]=66.2360 Asic[03]=67.0240 Asic[04]=61.4040 Asic[05]=65.1960 Asic[06]=66.6890 Asic[07]=64.3400 Asic[08]=62.3440
Asic[09]=62.7300 Asic[10]=65.0110 Asic[11]=65.3300 Asic[12]=64.4410 Asic[13]=66.4880 Asic[14]=62.2930 Asic[15]=64.9610 Asic[16]=66.9570
Asic[17]=71.0850 Asic[18]=69.2560
get RT hashrate from Chain[12]: (asic index start from 1-18)
Asic[01]=70.2620 Asic[02]=68.5680 Asic[03]=70.3460 Asic[04]=63.3000 Asic[05]=63.7860 Asic[06]=67.6450 Asic[07]=66.7060 Asic[08]=65.3970
Asic[09]=69.8770 Asic[10]=59.9110 Asic[11]=69.7420 Asic[12]=67.3260 Asic[13]=59.8440 Asic[14]=62.6460 Asic[15]=68.0980 Asic[16]=67.0920
Asic[17]=65.2800 Asic[18]=64.3070
get RT hashrate from Chain[13]: (asic index start from 1-18)
Asic[01]=64.3570 Asic[02]=66.5710 Asic[03]=69.9770 Asic[04]=66.9910 Asic[05]=70.0280 Asic[06]=66.1520 Asic[07]=67.5450 Asic[08]=61.0520
Asic[09]=63.3670 Asic[10]=68.5850 Asic[11]=62.8640 Asic[12]=69.1220 Asic[13]=60.5990 Asic[14]=63.4510 Asic[15]=63.5010 Asic[16]=67.4440
Asic[17]=63.7530 Asic[18]=67.3600
Check Chain[J4] ASIC RT error: (asic index start from 1-18)
Check Chain[J13] ASIC RT error: (asic index start from 1-18)
Check Chain[J14] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
do read temp on Chain[12]
Chain[12] Chip[1] TempTypeID=55 middle offset=26
Chain[12] Chip[1] local Temp=69
Chain[12] Chip[1] middle Temp=83
Special fix Chain[12] Chip[1] middle Temp = 84
Done read temp on Chain[12]
set FAN speed according to: temp_highest=69 temp_top1[PWM_T]=69 temp_top1[TEMP_POS_LOCAL]=69 temp_change=1 fix_fan_steps=0
FAN PWM: 86
read_temp_func Done!
CRC error counter=24078
Jump to: