Topic: Technobit Hex8A1 Coincraft in hand. (Read 4174 times)
Got mine today, working perfectly, stable 260Ghs on a tl-mr3020 with patched firmware and default settings.
But this thing is incredibly noisy ...
But this thing is incredibly noisy ...
Gratz gcube
Got mine today, working perfectly, stable 260Ghs on a tl-mr3020 with patched firmware and default settings.
But this thing is incredibly noisy ...
But this thing is incredibly noisy ...
Sorry, Dude,
I just had the chance to do it :
I just had the chance to do it :
nice toaster! =) *where can i get one?
New image for TL-MR3020 + cgminer 3.12.3 patch 0.2.0 Milestone release
Do I need to reset the TL-MR3020 back to factory settings for it to install?
If so how, do I do that?
Thanks.
No need to reset, just browse the new image & hit flash
But i usually use factory bin, i am prefer "fresh install"
New image for TL-MR3020 + cgminer 3.12.3 patch 0.2.0 Milestone release
Do I need to reset the TL-MR3020 back to factory settings for it to install?
If so how, do I do that?
Thanks.
Read the change long
Use *sysupgrade.bin for openwrt preflashed router or *facory.bin for factory FW router. As i call it a virgin one
Short answer no, but after you install it go to web interface cgminer configuration andfeel all blanks with default values quoted and Save+Apply
New image for TL-MR3020 + cgminer 3.12.3 patch 0.2.0 Milestone release
Do I need to reset the TL-MR3020 back to factory settings for it to install?
If so how, do I do that?
Thanks.
New image for TL-MR3020 + cgminer 3.12.3 patch 0.2.0 Milestone release
Morning fellows,
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
I was curious what kind of heatsink upgrade
how much you want for the miner? 1,4btc
First batch (only 30x units) cost €1,500
BTC right now = €511
I don't think anyone will part with one for 1.4BTC = instant loss.
I know you're hinting we could have bought an AntMiner, but AntMiner was 1.95BTC and BTC was €615 when these orders were taken.
Back then it looked the same $/GH, but with better GH/W, but sadly not now, such is the risk of buying on specs.
how much you want for the miner? 1,4btc
Morning fellows,
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all
Technobit team did their job just perfect
3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all
Technobit team did their job just perfect 3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
loshia what are the temps being reported back?
But it is getting hard to touch if not cooled right
I would say up to 25 maybe 30 celsius you will be ok with stock fans an heatsink. My room temp is not more than 15 because of the winter so cooler is always better
Good to hear. We keep our "mining room/datacenter" at about 18c but I heard these things need some space to themselves.
Morning fellows,
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all Technobit team did their job just perfect
3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all
Technobit team did their job just perfect 3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
loshia what are the temps being reported back?
But it is getting hard to touch if not cooled right
I would say up to 25 maybe 30 celsius you will be ok with stock fans an heatsink. My room temp is not more than 15 because of the winter so cooler is always better
Morning fellows,
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all Technobit team did their job just perfect
3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all
Technobit team did their job just perfect 3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
loshia what are the temps being reported back?
Quote
My board PIC FW and heat sink and fans were upgraded yesterday.
New photo of new heatsink/fans please!
45A = 540W is high for 28nm though! 0.5GH/1W is like an AntMiner but that has a huge heatsink to dissipate that heat.
I'm not a fan of the Sunon 4500rpm leaf blowers. Can't wait to get my hands on the Hex8A1 and see if I can make it quiet. I like a challenge!
I guess you can always throw more chips at the GH problem like AntMiner did if you can make them cheap enough.
It's a shame it wasn't a 16x chip board then it would really have rocked.
I am the kind who like to be insured. So 45a is at least 20% on top
If you want 1w/GH you can always have it undervolting/clocking the board no problem
Yeah, if I can get 200GH out of them with quiet fans somewhere around 0.7GH/1W (like the Bitfury) I'll be very happy.
I'll post in "hands on" with the results when I get mine.
Quote
My board PIC FW and heat sink and fans were upgraded yesterday.
New photo of new heatsink/fans please!
45A = 540W is high for 28nm though! 0.5GH/1W is like an AntMiner but that has a huge heatsink to dissipate that heat.
I'm not a fan of the Sunon 4500rpm leaf blowers. Can't wait to get my hands on the Hex8A1 and see if I can make it quiet. I like a challenge!
I guess you can always throw more chips at the GH problem like AntMiner did if you can make them cheap enough.
It's a shame it wasn't a 16x chip board then it would really have rocked.
I am the kind who like to be insured. So 45a is at least 20% on top
If you want 1w/GH you can always have it undervolting/clocking the board no problem
Yeah, if I can get 200GH out of them with quiet fans somewhere around 0.7GH/1W (like the Bitfury) I'll be very happy.
I'll post in "hands on" with the results when I get mine.
Quote
My board PIC FW and heat sink and fans were upgraded yesterday.
New photo of new heatsink/fans please!
45A = 540W is high for 28nm though! 0.5GH/1W is like an AntMiner but that has a huge heatsink to dissipate that heat.
I'm not a fan of the Sunon 4500rpm leaf blowers. Can't wait to get my hands on the Hex8A1 and see if I can make it quiet. I like a challenge!
I guess you can always throw more chips at the GH problem like AntMiner did if you can make them cheap enough.
It's a shame it wasn't a 16x chip board then it would really have rocked.
I am the kind who like to be insured. So 45a is at least 20% on top
If you want 1w/GH you can always have it undervolting/clocking the board no problem
Quote
My board PIC FW and heat sink and fans were upgraded yesterday.
New photo of new heatsink/fans please!
45A = 540W is high for 28nm though! 0.5GH/1W is like an AntMiner but that has a huge heatsink to dissipate that heat.
I'm not a fan of the Sunon 4500rpm leaf blowers. Can't wait to get my hands on the Hex8A1 and see if I can make it quiet. I like a challenge!
I guess you can always throw more chips at the GH problem like AntMiner did if you can make them cheap enough.
It's a shame it wasn't a 16x chip board then it would really have rocked.
Morning fellows,
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all Technobit team did their job just perfect
3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
My board PIC FW and heat sink and fans were upgraded yesterday. What I can tell you it rocks. Here are my results after 14+ hours nonstop mining
Some things to point out:
1. My stats are not settled yet, because I am mining at 512 diif + filtering out nonces inside ASIC chips which do not meet it. The board is making 270GH stable and there is some room for overclocking. BUT I do not feel brave enough to do it and I suggest to all of you not to push it too much. We are hiiting the limits of hardware especially voltage regulators so overdriving them for a long period is not good idea at all. This is my personal opinion. I do hope that there will be precise measurement of power consumption very soon. I am using single rail psu rated 55A/12V. I think the bottom line is at lest 45A, to be on a safe side
2. Tplink+cgminer worked rock stable without an issue. My pool reject rate is 0.12% only which is golden! I am not commenting my HW error rate at all
Technobit team did their job just perfect 3. What I can tell you that all of you should be able to get the 260Gh advertised at clock around 260 and voltage around 1000 mv. You have to experiment a little bit to find your sweet spot though.
More updates to come
Jump to: