Ubuntu Natty Narwhal 11.04 Mining Guide / HOWTO - page 7.

Christian Pezza

member

Activity: 154

Merit: 10

Quote from: ThiagoCMC on July 15, 2011, 10:51:45 PM

System stabilized, using vectors, 395MH / 89.00 ºC on both cores, now I want to do overclock but:

I run:

Code:

sudo aticonfig --initial -f --adapter=all

but:

Code:

root@garimpeiro-2:~# aticonfig --od-enable
ATI Overdrive(TM) enabled

root@garimpeiro-2:~# aticonfig --od-setclocks=900,1000 --adapter=all
ERROR - Set clocks failed for Adapter 0 - AMD Radeon HD 6990
        Please check that input values were valid
ERROR - Set clocks failed for Adapter 1 - AMD Radeon HD 6990
        Please check that input values were valid

What can I do?!

Is there some setup that I can manually include within xorg.conf?

Thanks!
Thiago

run aticonfig --odgc --adapter=all
you know what is the range of values u can input and from there there is the art of OC where I don't have any luck because keep freezen on me! Sad

but with some cards and some right set works awesome

good luck Wink

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

System stabilized, using vectors, 395MH / 89.00 ºC on both cores, now I want to do overclock but:

I run:

Code:

sudo aticonfig --initial -f --adapter=all

but:

Code:

root@garimpeiro-2:~# aticonfig --od-enable
ATI Overdrive(TM) enabled

root@garimpeiro-2:~# aticonfig --od-setclocks=900,1000 --adapter=all
ERROR - Set clocks failed for Adapter 0 - AMD Radeon HD 6990
        Please check that input values were valid
ERROR - Set clocks failed for Adapter 1 - AMD Radeon HD 6990
        Please check that input values were valid

What can I do?!

Is there some setup that I can manually include within xorg.conf?

Thanks!
Thiago

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

Shit! $#@%#$$#$%@#$%@F Cry

Now even with no "-v", the temperature is 94.00 ºC for GPU0 and 95.50 ºC for GPU1...

Damn it

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

Now I chaged poclbm:

./poclbm.py -v -d0 -f0 http://X:[email protected]:8332 - [392.275 MH/s (~113 MH/s)] - 92.50 ºC

./poclbm.py -v -d1 -f0 http://X:[email protected]:8332 - [392.422 MH/s (~112 MH/s)] - 93.50 ºC

I'm very concerned about the temperature... Please, some advice?! Bought a watercooler?

I'll disable "-v" for instance...

Thanks!
Thiago

Christian Pezza

member

Activity: 154

Merit: 10

works thank you

about 100c from my reading and some users asked XFX customer service they don't suggest to go over 94c!

I already burn one 6950 because of it :/

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

Quote from: ThiagoCMC on July 15, 2011, 08:58:52 PM

Hi!

I'm running:

./phoenix.py -u http://X:[email protected]:8332/ -k phatk VECTORS AGGRESSION=14 BFI_INT WORKSIZE=128 FASTLOOP=false DEVICE=0

MHash: 395
Temp: 87.0 C

./phoenix.py -u http://X:[email protected]:8332/ -k phatk VECTORS AGGRESSION=14 BFI_INT WORKSIZE=128 FASTLOOP=false DEVICE=1

MHash: 290
Temp: 79

What am I doing wrong?!

Thanks!!
Thiago

Hi! I figure out the following to stabilize:

"Do not run the gnome / X applications while mining!" \o/

1- reboot
2- login via SSH with root
3- run: service gdm stop
4- run: screen -aAdR
5- run: X

6- Press: control+a c
7- run: ./poclbm.py -d0 -f0 -w128 http://X:[email protected]:8332 - getting [357.657 MH/s (~400 MH/s)] - temp 89.50 C

8- Press: control+a c
9- run: ./poclbm.py -d1 -f0 -w128 http://X:[email protected]:8332 - getting [357.701 MH/s (~250 MH/s)] - temp 89.50 C

But if I change the poclbm to phoenix, I got:

7- run: ./phoenix.py -u http://X:[email protected]:8332/ -k phatk VECTORS AGGRESSION=12 BFI_INT WORKSIZE=128 FASTLOOP=false DEVICE=0 - [395.46 Mhash/sec] - temp 98.00 C

9- run: ./phoenix.py -u http://X:[email protected]:8332/ -k phatk VECTORS AGGRESSION=12 BFI_INT WORKSIZE=128 FASTLOOP=false DEVICE=1 - [395.34 Mhash/sec] - temp 97.10 C

All coolers are running at 100%.

No overclock, I just bought the 6990 and install, all defaults from factory.

My question is: It is safe to run close to 100 ºC ??!

Code:

root@garimpeiro-2:~# aticonfig --odgc --adapter=all

Adapter 0 - AMD Radeon HD 6990
   Core (MHz) Memory (MHz)
   Current Clocks : 880 1250
   Current Peak : 880 1250
  Configurable Peak Range : [500-1200] [1250-1500]
   GPU load : 99%

Adapter 1 - AMD Radeon HD 6990
   Core (MHz) Memory (MHz)
   Current Clocks : 880 1250
   Current Peak : 880 1250
  Configurable Peak Range : [500-1200] [1250-1500]
   GPU load : 99%

Second question: anybody running water-cooled 6990?
I'm thinking in get one of these:

http://www.koolance.com/water-cooling/product_info.php?product_id=1117
http://www.swiftech.com/epsilonhd-6990fullcovervgawaterblock.aspx

What do you guys think?!

Cheers,
Thiago

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

Quote from: Christian Pezza on July 15, 2011, 09:45:58 PM

help, I try to install another system and after all installing etc I am getting

poclbm.py: error: no such option: --SERVER

any advise please?

Just remove "--server"

./poclbm.py -d0 -f0 -w128 http://X:[email protected]:8332

Christian Pezza

member

Activity: 154

Merit: 10

help, I try to install another system and after all installing etc I am getting

poclbm.py: error: no such option: --SERVER

any advise please?

Christian Pezza

member

Activity: 154

Merit: 10

Quote from: stellan0r on July 14, 2011, 03:35:09 AM

Quote from: Christian Pezza on July 09, 2011, 10:10:19 PM

Hello

there is a way I can have one console and manage multiple GPU in the same machine or/and more machine(GPU'S) from may LAN?

ps Inaba thank you so much for your work and all of you partecipating of this forum!!! Just open up new opportunity for me!

asap I will donate but let me get some BTC first Wink

cp you can use the command "screen" in your terminal window / ssh session.
just connect to your miner via LAN (works also via internet if you have a static ip or a dynamic dns service Wink

), enter "screen" and a new prompt appears. start your miner or whatever, and then hit ctrl+A (together, hold both) and then hit C. then a new prompt appears, you get a new tab in that terminal window. like tabed browsing in firefox (just without the tabs to click at). enter your commands here. open a new "window" with ctrl+A +C again and so on.

cycle through windows with ctrl+A (again hold both keys) +N (for next) or +P (for previous) to go forward and backwards through your tabs.

you can close the terminal window with the screen ssh session and resume it even after restarting the computer you used to ssh into the miner or from another machine, just connect to your miner again and type "screen -r" into your terminal. et voila, you can flip through your screen tabs again.

With this method you will need only 1 window per miner with as many gpus inside as you want.

stellan0r, thank you for the tip I just was wishing to have a more friendly way of something cn regroup up to 15 GPU. It could become too busy. I got someone told me was possible but I have to just look in the net how... so just trying to get that way to do it make it practical

In the mean time I will practice what you suggest me!

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

Hi!

I'm running:

./phoenix.py -u http://X:[email protected]:8332/ -k phatk VECTORS AGGRESSION=14 BFI_INT WORKSIZE=128 FASTLOOP=false DEVICE=0

MHash: 395
Temp: 87.0 C

./phoenix.py -u http://X:[email protected]:8332/ -k phatk VECTORS AGGRESSION=14 BFI_INT WORKSIZE=128 FASTLOOP=false DEVICE=1

MHash: 290
Temp: 79

What am I doing wrong?!

Thanks!!
Thiago

ThiagoCMC

legendary

Activity: 1204

Merit: 1000

฿itcoin: Currency of Resistance!

Guys!

Why this guide does not use the "ati-driver-installer-11-6-x86.x86_64.run"?

Sorry but, my 6990 arrives today and I'm already mining but, the system is pretty weird, the GPU0 reaches 395MH but the gpu1 reaches only 300MH...

The temperature is around 89~83, is that normal?

The cooler is running at high speed.

Thanks!
Thiago

Inaba

legendary

Activity: 1260

Merit: 1000

No problem... USE MY POOL!

CYPER

hero member

Activity: 812

Merit: 502

Quote from: Inaba on July 15, 2011, 10:17:28 AM

Ok, you can download the file from my site: https://eclipsemc.com/files/python-jsonrpc.tar.gz

You can then untar it in your directory and continue on instead of the svn checkout.

Thanks you are a saviour Wink

Inaba

legendary

Activity: 1260

Merit: 1000

Ok, you can download the file from my site: https://eclipsemc.com/files/python-jsonrpc.tar.gz

You can then untar it in your directory and continue on instead of the svn checkout.

Flappy

member

Activity: 99

Merit: 10

Quote from: m0w3r on July 13, 2011, 11:12:53 PM

The json-rpc.org site appears to be down. Is there an alternative? Thanks.

edit - this really sucks that I'm unable to continue due to this repository being down, now on 2nd day

Me too.

stellan0r

hero member

Activity: 574

Merit: 500

Medical Translations for Bitcoins

Quote from: Christian Pezza on July 09, 2011, 10:10:19 PM

Hello

there is a way I can have one console and manage multiple GPU in the same machine or/and more machine(GPU'S) from may LAN?

ps Inaba thank you so much for your work and all of you partecipating of this forum!!! Just open up new opportunity for me!

asap I will donate but let me get some BTC first Wink

cp you can use the command "screen" in your terminal window / ssh session.
just connect to your miner via LAN (works also via internet if you have a static ip or a dynamic dns service Wink

), enter "screen" and a new prompt appears. start your miner or whatever, and then hit ctrl+A (together, hold both) and then hit C. then a new prompt appears, you get a new tab in that terminal window. like tabed browsing in firefox (just without the tabs to click at). enter your commands here. open a new "window" with ctrl+A +C again and so on.

cycle through windows with ctrl+A (again hold both keys) +N (for next) or +P (for previous) to go forward and backwards through your tabs.

you can close the terminal window with the screen ssh session and resume it even after restarting the computer you used to ssh into the miner or from another machine, just connect to your miner again and type "screen -r" into your terminal. et voila, you can flip through your screen tabs again.

With this method you will need only 1 window per miner with as many gpus inside as you want.

m0w3r

full member

Activity: 131

Merit: 100

The json-rpc.org site appears to be down. Is there an alternative? Thanks.

edit - this really sucks that I'm unable to continue due to this repository being down, now on 2nd day

irishmick

full member

Activity: 134

Merit: 100

Thanks. Adding noprompt worked. Gratuity on its way to you.

Inaba

legendary

Activity: 1260

Merit: 1000

Not really sure what you are asking specifically?

There was/is a program floating around that does what you want I think, though I've never used it myself and I couldn't tell you what the name is off hand. It's in the forums somewhere though.

Christian Pezza

member

Activity: 154

Merit: 10

Hello

there is a way I can have one console and manage multiple GPU in the same machine or/and more machine(GPU'S) from may LAN?

ps Inaba thank you so much for your work and all of you partecipating of this forum!!! Just open up new opportunity for me!

asap I will donate but let me get some BTC first Wink

Topic: Ubuntu Natty Narwhal 11.04 Mining Guide / HOWTO - page 7. (Read 281466 times)